DYNAMIX Wi-Fi VoIP Gateway DW 3512 Technical Manaul Revision information Version Date Description EN-V1.00 Jul-19-2007 1st English version Copyright © 2007 Dynamix Pro., Ltd. All right reserved.
Dynamix DW 3512 Technical Manual V1.
Dynamix DW 3512 Technical Manual V1.
Dynamix DW 3512 Technical Manual V1.
Dynamix DW 3512 Technical Manual V1.00 Chapter 1 Overview of the DW 3512 DW 3512 is a two-port FXS + one PSTN wireless gateway, which supports RFC3261 SIP protocol. Telephone will switch to PSTN port automatically under power failure. User can also select to dial out through PSTN line manually. DW 3512 complies with wireless protocol 802.11 b/g, and can operate as Access Point or Client. Built-in four LAN ports and NAT function allows other devices to access network more easily.
Dynamix DW 3512 Technical Manual V1.00 802.11b/g client mode WISP Mode WDS and Universal Repeater Mode 802.1d with spanning tree protocol NAT/NAPT Firewall Virtual DMZ ALG for:FTP, SIP, VPN pass-through with multiple sessions (IPSEC, L2TP) DHCP client and server Up to 98MB throughput at Bridge Mode Qos: 802.
Dynamix DW 3512 Technical Manual V1.00 System log Display real-time information for system setting, statistics, and associated wireless client status. User name/password authentication for web server login and logout Web-based configuration and management interface Firmware update through web Configuration backup/restore to/from a file.
Dynamix DW 3512 Technical Manual V1.00 Front View LED Indicator 10 9 8 7 6 5 4 3 2 1 Status Light On Light Off Light Flashing 1 Power power on power off N/A 2 WLAN N/A N/A WLAN is transmitting or receiving data. 3 4 5 6 7 8 9 10 PSTN Phone 2 Phone 1 LAN 4 LAN 3 LAN 2 LAN 1 WAN Gateway fails to Gateway succeeds to PSTN has incoming call or register on Proxy register on Proxy PSTN line is in use.
Dynamix DW 3512 Technical Manual V1.00 Back View A B C D E F G Port/ Button Functions A 12V DC Input AC 100V~120V. Output DC12V. B Reset Press Reset key over 5 seconds, DW3512 will reboot and all configurations will restore to default values. If user press Reset key for 3-5 seconds, DW 3512 will only reboot, but not return to default values. C PSTN RJ-11 interface for connecting the extension line of PABX or PSTN Line.
Dynamix DW 3512 Technical Manual V1.00 Call Features Direct IP Call User can dial out call with IP address directly. ¾ Dial IP: ex. To dial out IP 192.168.1.1 via phone set need to press 192*168*1*1#. “#” means to dial out immediately, if user doesn’t follow by “#” sign, DW3512 will dial out after “auto dial time”. ¾ Dial IP and port: To dial out IP 192.168.1.1 and port 5061 via phone set need to press 192*168*1*1**5061#.
Dynamix DW 3512 Technical Manual V1.00 4) Phone 1 dial to B, both Phone 1 and A will hear ring back tone. 5) B picks up, B and C in communication, A hear busy tone and disconnect. Copyright © 2007 Dynamix Pro., Ltd. All right reserved.
Dynamix DW 3512 Technical Manual V1.00 Chapter 2 Configuring the DW3512 through Voice Prompt and Phone set Please connect one analog phone set with Phone 1 port of DW3512, and then input specific keys as below to get some information or make brief configurations. Category Function Input Key Example DHCP client for WAN #111 #111# Set Fixed IP for WAN #112 Set Netmask for WAN #113 Set Gateway for WAN #114 Set DNS #115 Set Network Settings #112192*168*0*100# set IP as 192.168.0.
Dynamix DW 3512 Technical Manual V1.00 #13001# Set 711 u-law to be first priority codec. Codec Number: 01: G.711 u-law 02: G.711 a-law Set first priority codec #130 + first priority codec 03: G.729 04: G.723 6.3k 05: G.723 5.3k 06: G.726-16 07: G.726-24 08: G.726-32 09: G.
Dynamix DW 3512 Technical Manual EN-V1.00 Chapter 3 Configuring the DW 3512 through Web Pages The HTTP web management interface provides user an easy way to configure DW3512. PC LAN IP address: DHCP Power Adapter PC WLAN IP address: DHCP ESSID: WiFi_AP Channel: 11 Encryption: disabled LAN WAN SOHO Router DW 3512 WAN default IP address: DHCP LAN default IP address: 192.168.123.123 SSID: WiFi_AP Channel: 11 Encryption: disabled ADSL/ Cable Modem Internet Step 1. Power on the DW 3512 Step 2.
Dynamix DW 3512 Technical Manual V1.00 Step 5. Start to configure After enter web management interface, user can see 8 main items. 1. Setup Wizard: User can follow steps in wizard to make first-time initial configuration. 2. Operation Mode: User can setup different modes to LAN and WLAN interface for NAT and bridging function. 3. Wireless: User can set all wireless related parameters here. 4. TCP/IP: User can set LAN and WAN related configurations here. 5.
Dynamix DW 3512 Technical Manual V1.00 Setup Wizard The setup wizard will guide you to configure access point for first time. Please follow the setup wizard step by step. Press Cancel will return to the first page of Setup Wizard. Press Next>> to next step. Press <
Dynamix DW 3512 Technical Manual V1.00 DHCP client or static IP. Time Zone Setting You can maintain the system time by synchronizing with a public time server over the Internet. ¾ Enable NTP client update: User can update time of DW3512 from NTP server if this function is enabled. ¾ Time Zone Select: Select the time zone according to location. ¾ NTP server: User may select one NTP server for DW3512 to update current time. Copyright © 2007 Dynamix Pro., Ltd. All right reserved.
Dynamix DW 3512 Technical Manual V1.00 LAN Interface Setup This page is used to configure the parameters for local area network which connects to the LAN port of your Access Point. Here you may change the setting for IP address, subnet mask, DHCP, etc… ¾ IP Address: Set IP address of LAN interface. ¾ Subnet Mask: Set subnet mask of LAN interface. WAN Interface Setup This page is used to configure the parameters for Internet network which connects to the WAN port of your Access Point.
Dynamix DW 3512 Technical Manual V1.00 ¾ DHCP Client: Set WAN interface as DHCP mode. ¾ PPPoE: Set WAN interface as PPPoE mode. 1) User Name: Set user name of PPPoE connection. 2) Password: Set password of PPPoE connection. Copyright © 2007 Dynamix Pro., Ltd. All right reserved.
Dynamix DW 3512 Technical Manual V1.00 Wireless Basic Settings This page is used to configure the parameters for wireless LAN clients, which may connect to your Access Point. ¾ Band: Select wireless band as 802.11b, 802.11g, or 802.11b+g. ¾ Mode: Select wireless mode. User could find 4 different modes here, including AP, Client, WDS, AP+WDS. AP mode enables DW3512 as wireless access point and allows other devices to connect wirelessly to a wired Ethernet network.
Dynamix DW 3512 Technical Manual V1.00 Wireless Security Setup This page allows you setup the wireless security. Turn on WEP or WPA by using Encryption Keys could prevent any unauthorized access to your wireless network. ¾ Encryption: Set encryption as none, WEP, WPA, WPA2 or WPA2 Mixed. Copyright © 2007 Dynamix Pro., Ltd. All right reserved.
Dynamix DW 3512 Technical Manual V1.00 1) WEP: When encryption WEP is selected, you must set WEP key value. Only user with the same WEP key can connect to the DW3512. • Key Length: set WEP key length as 64 or 128 bits and select user to transmit data using 64 or 128 bits WEP key encryption. 64 bits represents a lower level encryption for security, and uses ASCII (5 characters) or Hex (10 characters) encryption scheme as a secret key.
Dynamix DW 3512 Technical Manual V1.00 • Pre-Shared Key: set pre-shared key manually. 3) WPA2(AES): AES ( Advance Encryption Standard) is the U.S. government’s next generation cryptography algorithm. • Pre-Shared Key Format: Select Pre-Shared Key Format as Passphrase or Hex (64 characters). • Pre-Shared Key: set pre-shared key manually. Copyright © 2007 Dynamix Pro., Ltd. All right reserved.
Dynamix DW 3512 Technical Manual V1.00 4) WPA2 Mixed • Pre-Shared Key Format: Select Pre-Shared Key Format as Passphrase or Hex (64 characters). • Pre-Shared Key: set pre-shared key manually. Operation Mode You can setup different modes to LAN and WLAN interface for NAT and bridging function. DW3512 provide all 3 primary modes and 4 extended modes. Here you can find 3 primary modes, including: 1) Gateway mode, 2) Bridge mode, 3) Wireless ISP.
Dynamix DW 3512 Technical Manual V1.00 For more information regarding Operation Modes, please refer to CH 4 Wireless Operation Modes. Wireless Basic Settings This page is used to configure the parameters for wireless LAN clients which may connect to your Access Point. ¾ Disable Wireless LAN Interface: If user checks his function, wireless LAN will be disabled. In other words, this device will not be visible by any wireless station. ¾ Band: Select wireless band as 802.11b, 802.11g, or 802.11b+g.
Dynamix DW 3512 Technical Manual V1.00 Identifier). You may use the default SSID unless there more than one DW3512 in the same area. In this case, you should specify different SSID for each DW3512. ¾ Channel Number: Set channel for wireless connection. You can set channel for radio communication manually. If you set it as Auto, the DW3512 will select a clear channel during boot up. ¾ Associated Clients: Press Show Active Clients to see which client registers on this DW3512.
Dynamix DW 3512 Technical Manual V1.00 divided from 802.11 frames. If there are excessive collisions over WLAN, user can try different fragment size to increase reliability. ¾ RTS Threshold (0-2347): RTS Threshold is a mechanism implemented to prevent the problem of “Hidden Node”. “Hidden Node” is a situation in which two stations are within range of the same Access Point, but are not within range of each other. Therefore, they are hidden nodes for each other.
Dynamix DW 3512 Technical Manual V1.00 Security This page allows you setup the wireless security. Turn on WEP or WPA by using Encryption Keys could prevent any unauthorized access to your wireless network. ¾ Encryption: Set encryption as none, WEP, WPA, WPA2 or WPA2 Mixed. ¾ Set WEP Key: When encryption WEP is selected, you must set WEP key value. 1) Key Length: Set WEP key length as 64 or 128 bits. 2) Key Format: Set key format as ASCII (5 characters) if you are using ASCII characters.
Dynamix DW 3512 Technical Manual V1.00 format and fill in Pre-Shared Key. ¾ WPA Cipher Suite: Select WPA Cipher Suite to be TKIP or AES, this field is used as a password to begin the encryption process. ¾ WPA2 Cipher Suite: Select WPA Cipher Suite to be TKIP or AES. WPA is an encryption standard proposed by WiFi for advance protection. It is more secure than WEP encryption. ¾ Pre-Shared Key Format: There are two formats for choice to set the Pre-Shared key, i.e. Passphrase and Hex.
Dynamix DW 3512 Technical Manual V1.00 Access Control If you choose Allowed Listed, only those clients whose wireless MAC addresses are in the access control list will be able to connect to your Access Point. When Deny Listed is selected, these wireless clients on the list will not be able to connect the Access Point. ¾ Wireless Access Control Mode: Set disable control, allow list or deny list. If user set control mode as Allow Listed, please add MAC address below to increase Allow List.
Dynamix DW 3512 Technical Manual V1.00 ¾ Set Security: This setting is use between both wireless AP/ Router device. ¾ Show Statistics: Show the current statistics of WDS. ¾ Current WDS AP List: Show the current WDS AP list. Site Survey This page provides tool to scan the wireless network. If any Access Point or IBSS is found, you could choose to connect it manually when client mode is enabled. TCP/IP Settings LAN Interface ¾ IP Address: Set IP address of LAN interface.
Dynamix DW 3512 Technical Manual V1.00 ¾ Default Gateway: Set default gateway of LAN interface. It is normally used when Bridge mode is enabled. ¾ DHCP: Set DHCP mode to be disabled, Client, or Server. When user set DHCP mode as server mode, please set DHCP Client Range for LAN interface to assign DHCP IP. ¾ Show Client: Press this key can check current DHCP clients that captured IP from DW3512. Press Refresh can renew screen display, and press Close can close window.
Dynamix DW 3512 Technical Manual V1.00 9) Enable Web Server Access on WAN: If this function is checked to enable, user can enter Web Server management of DW3512 through WAN IP address. 10) Enable IPsec pass through on VPN connection: check to enable IPsec function. 11) Enable PPTP pass through on VPN connection: check to enable PPTP pass through function. 12) Enable L2TP pass through on VPN connection: check to enable L2TP pass through function. ¾ DHCP Client: Set WAN interface as DHCP mode.
Dynamix DW 3512 Technical Manual V1.00 5) Enable Ping Access on WAN: If this function is checked to enable, user can reach DW3512 via Ping WAN IP address. 6) Enable Web Server Access on WAN: If this function is checked to enable, user can enter Web Server management of DW3512 through WAN IP address. 7) Enable IPsec pass through on VPN connection: check to enable IPsec function. 8) Enable PPTP pass through on VPN connection: check to enable PPTP pass through function.
Dynamix DW 3512 Technical Manual V1.00 when PPPoE disconnect. If user set type as Connect on Demand, please set following idle time, DW3512 will check connection after this time. If user set type as Manual, DW3512 will only connect or disconnect by press Connect or Disconnect manually. 5) Idle Time: Set PPPoE connection idle time for Connect on Demand. 6) MTU Size: Set MTU (maximum transmission unit) size.
Dynamix DW 3512 Technical Manual V1.00 Firewall Port Filtering Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway. Use of such filters can be helpful in securing or restricting your local network. ¾ Enable Port Filtering: check to enable Port Filtering function. ¾ Port Range: set start port and end port for port filtering range. ¾ Protocol: set protocol as TCP or UDP or both protocol.
Dynamix DW 3512 Technical Manual V1.00 ¾ Comment: Make description for this IP filtering rule. MAC Filtering Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway. Use of such filters can be helpful in securing or restricting your local network. ¾ Enable MAC Filtering: check to enable MAC Filtering function. ¾ MAC Address: set MAC Address for MAC filtering. ¾ Comment: Make description for this MAC filtering rule.
Dynamix DW 3512 Technical Manual V1.00 URL Filtering URL filter is used to deny LAN users from accessing the internet. Block those URLs which contain keywords listed below. ¾ Enable URL Filtering: check to enable URL Filtering function. ¾ URL Address: set URL address for URL filtering function. Port Forwarding Entries in this table allow you to automatically redirect common network services to a specific machine behind the NAT firewall.
Dynamix DW 3512 Technical Manual V1.00 DMZ A Demilitarized Zone is used to provide Internet services without sacrificing unauthorized access to its local private network. Typically, the DMZ host contains devices accessible to Internet traffic, such as Web (HTTP ) servers, FTP servers, SMTP (e-mail) servers and DNS servers. ¾ Enable DMZ: check to enable DMZ function. ¾ DMZ Host Address: set IP address for DMZ function.
Dynamix DW 3512 Technical Manual V1.00 1) Display Name: Set WiFi Phone display name for caller ID information. 2) Number: Set registering Phone number. 3) Login ID: If Proxy server needs registration authentication please input Login ID here. 4) Password: If Proxy server needs registration authentication please input password here. ¾ SIP Proxy 1) Proxy: Check to enable Proxy mode. 2) Proxy Addr: If user enable Proxy mode, please input Proxy address.
Dynamix DW 3512 Technical Manual V1.00 4) Busy Number: Enter the assigned number for busy forward. 5) No Answer Forward to: Check to enable no answer forward function. When phone is not answered for a period of time, incoming call will be forwarded to assigned number. 6) No Answer Number: Enter assigned number for no answer forward. 7) No Answer Time (sec): Set no answer time. Once phone is not picked up after this time, incoming call be will forwarded to assigned number.
Dynamix DW 3512 Technical Manual V1.00 2) T.38 Port: Set T.38 port for FAX. ¾ Hot Line 1) Use Hot Line: Check to enable Hot Line function. 2) Hot Line Number: Set the destination number for Hot Line function.. ¾ DND (Don’t Disturb) 1) DND Mode: You can select 3 mode of DND. The call will be always rejected if Always is selected. The call will be rejected by below Time setting (From and To) if Enable is selected. The call will be accepted if Disable is selected.
Dynamix DW 3512 Technical Manual V1.00 Copyright © 2007 Dynamix Pro., Ltd. All right reserved.
Dynamix DW 3512 Technical Manual V1.00 Copyright © 2007 Dynamix Pro., Ltd. All right reserved.
Dynamix DW 3512 Technical Manual V1.00 Tone ¾ Select Country User can select country to specify tone parameters (Dial Tone, Ring Tone, Busy Tone, and Waiting Tone). If user wants to set tone manually, please select CUSTOMER. After selecting CUSTOMER, user can assign Custom 1 to 8 for each tone. ¾ Select Custom Tone: Select Custom tone number to set Tone Parameters. ¾ Tone Parameters: 1) CanOn: set cadence time for tone to play in ms.
Dynamix DW 3512 Technical Manual V1.00 tone will be played for 100ms. 2) CanOff: set cadence time for tone not to play in ms. For example, if set CanOff as 100, the tone will stop playing for 100ms. 3) Freq1: set first set of tone frequency in Hz. 4) Freq2: set second set of tone frequency in Hz. This frequency is optional. 5) Gain1: set volume level of Freq1 in dB (-7~-10). Please set this parameter under zero and suggested to set between –7 to –10. 6) Gain2: set volume level of Freq2 in dB (-7~-10).
Dynamix DW 3512 Technical Manual V1.00 PSTN Set hotkey to switch to PSTN line. Please notice that the key must be *+0-9. When user wants to dial out from PSTN line, press this special key first, phone will pass to PSTN line. Other ¾ Call Transfer: Set call transfer function key. ¾ Auto Dial Time: Set Auto dial time. When user finish input number after this time, Gateway will dial out immediately.
Dynamix DW 3512 Technical Manual V1.00 When DSCP is defined, a DSCP will be added in SIP and RTP packets, and the priority of voice should be higher than data. ¾ VLAN 1) VLAN Packets: Check to enable VLAN function. 2) VLAN ID: Set VLAN ID. 3) User Priority: Set user priority. 4) CFI: Set CFI (canonical format indicator). Config ¾ Save Settings to File: Save current VoIP settings to a file. ¾ Load Settings from File: Browse and load setting from file.
Dynamix DW 3512 Technical Manual V1.00 Management Status In this page can show the current status and some basic settings of the DW3512. Copyright © 2007 Dynamix Pro., Ltd. All right reserved.
Dynamix DW 3512 Technical Manual V1.00 Statistics This page shows the packet counters for transmission and reception regarding to wireless and Ethernet networks. DDNS Dynamic DNS is a service, which provides you with a valid, unchanging, internet domain name (an URL) to go with that (possibly ever-changing) IP-address. Before setting this page, you should click below link to DynDNS or TZO to apply an account for DDNS. ¾ Enable DDNS: Check to enable DDNS function.
Dynamix DW 3512 Technical Manual V1.00 Time Zone Setting You can maintain the system time by synchronizing with a public time server over the Internet. ¾ Current Time: input current time manually. ¾ Time Zone Select: select local time zone according to location. ¾ Enable NTP client update: check to enable NTP update. Once this function is enabled, DW3512 will automatically update current time from NTP server. ¾ NTP Server: User may select prefer NTP sever or input address of NTP server manually.
Dynamix DW 3512 Technical Manual V1.00 Denial-of-Service A "denial-of-service" (DoS) attack is characterized by an explicit attempt by hackers to prevent legitimate users of a service from using that service. ¾ Enable DoS Prevention: Check to enable DoS function. ¾ User may set other related configurations about DoS below. Log This page can be used to set remote log server and show the system log. ¾ Enable Log: check to enable log function.
Dynamix DW 3512 Technical Manual V1.00 in this remote server. This is compatible with Linux Syslog server. Upgrade Firmware This page allows you upgrade the Access Point firmware to new version. Please note, do not power off the device during the upload because it may crash the system. ¾ Select File: browse and select file you want to upgrade and press Upload to perform upgrade. Please wait till on screen shows related information after upgrade finished. Copyright © 2007 Dynamix Pro., Ltd.
Dynamix DW 3512 Technical Manual V1.00 Save/Reload Settings This page allows you save current settings to a file or reload the settings from the file which was saved previously. Besides, you could reset the current configuration to factory default. ¾ Save Settings to File: save current settings to a file. ¾ Load Settings from File: browse a file and upload to reload settings. ¾ Reset Settings to Default: pres Reset will clean all current configurations and return to default values.
Dynamix DW 3512 Technical Manual V1.00 ¾ User Name: Enter user name. ¾ New Password: input password for this user. ¾ Confirmed Password: confirm password again. System Reboot Press Reboot to reboot system. Please wait for a few minutes and reload web page again. Copyright © 2007 Dynamix Pro., Ltd. All right reserved.
Dynamix DW 3512 Technical Manual V1.00 Chapter 4 Wireless Operation Modes The DW3512 provides 8 modes for wireless operation, including: Access Point: With NAT and Without NAT. Client (Infrastructure) Client (Ad-hoc) P2P Bridge WDS Repeater Universal Repeater WISP WISP + Universal Repeater Here we will guide the purpose and configuration steps for these modes.
Dynamix DW 3512 Technical Manual V1.00 enabled and PCs in LAN ports and WLAN share the same IP to ISP through WAN port. ¾ Step4: Go to the page of TCP/IPÆ WAN set the necessary IP information for WAN. ¾ Step5: If necessary, go to the page of TCP/IPÆ LAN to set the advanced settings for LAN. Such as DHCP server…etc. ¾ Step6: Go to the page of WirelessÆ Basic Settings, set the mode to AP. Please also change the SSID to another name if necessary.
Dynamix DW 3512 Technical Manual V1.00 servers exist in your Office LAN and your PCs may get IP from a wrong DHCP server. ¾ Step5: Please renew the IP settings of the PC which connect with the LAN port of 3512. Then the PC should get new IP from the DHCP server which connected with your Office LAN. ¾ Step6: Go to the page of WirelessÆ Basic Settings, set the mode to AP. Please also change the SSID to another name if necessary.
Dynamix DW3512 Technical Manual V1.00 page of TCP/IPÆ LAN to set the network settings to connect with DW3512-A. Maybe you could set the IP to 192.168.123.200 and set Default Gateway to 192.168.123.123. ¾ Step5: Go to the page of WirelessÆ Basic Settings, set the mode to Client and set the Network Type to Infrastructure. ¾ Step6: Go to the page of WirelessÆ Security, to set the necessary authentication method for DW3512-A if DW3512-A has enable authentication.
Dynamix DW 3512 Technical Manual V1.00 P2P Bridge In this mode, 2 access points in two remote locations connect to each other to provide a wireless bridge between 2 remote LANs. It is mostly used by enterprise to connect 2 remote office’s network together. This feature is also useful when users want to bridge networks between buildings where it is impossible to deploy network cable connections between these buildings. The P2P Bridge should be connected by using WDS Repeater.
Dynamix DW 3512 Technical Manual V1.00 ¾ Step4: When Bridge mode is enabled, the WAN configuration is disabled, so please go to the page of TCP/IPÆ LAN to set the network settings to connect with your Office LAN. In this example, we set the LAN IP to 192.168.123.200 and DHCP is disabled. ¾ Step5: Login 192.168.123.200. Go to the page of WirelessÆ Basic Settings, set the mode to WDS. Set the Channel to a fixed one, such as 11.
Dynamix DW 3512 Technical Manual V1.00 ¾ Step2: Enter 192.168.123.123 for the WEB interface of DW3512-A with no login ID and password. ¾ Step3: Go to the page of Operation, set DW3512-A to Bridge mode. In this mode, all Ethernet ports and wireless interface are bridged together and NAT function is disabled. All the WAN related function and firewall are not supported.
Dynamix DW 3512 Technical Manual V1.00 DW3512 could be the same or different. And you should set the WDS table for each other. Universal Repeater A Universal repeater can also extend the wireless coverage of another wireless AP or router. But the Universal Repeater does not require the remote side to have WDS function. Below is an example to show you how to implement Universal Repeater with Bridge mode. Notebook with wireless Notebook with wireless network Adapter network Adapter DW3512-A LAN IP: 192.
Dynamix DW 3512 Technical Manual V1.00 password. ¾ Step3: Go to the page of Operation, set DW3512 to Bridge mode. In this mode, all Ethernet ports and wireless interface are bridged together and NAT function is disabled. All the WAN related function and firewall are not supported. ¾ Step4: When Bridge mode is enabled, the WAN configuration is disabled, so please go to the page of TCP/IPÆ LAN to set the network settings to connect with your Office LAN. In this example, we set the LAN IP to 192.168.123.
Dynamix DW 3512 Technical Manual V1.00 ¾ Step1: Power on DW3512-A and set one pc to connect with DW3512-A’s LAN. Set PC to DHCP then PC should got an IP as 192.168.123.x by default. ¾ Step2: Enter 192.168.123.123 for the WEB interface of DW3512-A with no login ID and password. ¾ Step3: Go to the page of Operation, set DW3512-A to Wireless ISP mode. ¾ Step4: Go to the page of WirelessÆ Basic Settings, set the mode to Client and set the Network Type to Infrastructure.
Dynamix DW 3512 Technical Manual V1.00 ¾ Step4: Go to the page of WirelessÆ Basic Settings, set the mode to Client and set the Network Type to Infrastructure. ¾ Step5: Go to the page of WirelessÆ Security, to set the necessary authentication method for WISP Outdoor AP, if WISP Outdoor AP has enable authentication. ¾ Step6: Go to the page of WirelessÆ Site Survey to search and connect to WISP Outdoor AP. When connection is OK, there should be a successful message appeared.
