Installation Guide

ManualsBrandsHome Styles ManualsKitchen Appliance32x72x17 in. Crescent Hill Pantry Cabinet in Dark Tortoise Shell

IMPORTANT NOTE

Carefully remove all the parts from the carton and put

them individually on a soft cloth to prevent scratches

or other damage occurring to the parts.

We have taken great care in the design of this

product and request that you carefully and strictly

follow our assembly instructions to ensure a

completed product as it was designed.

Part List

Home Styles Consumer Assistance: www.homestyles-furniture.com,

servicedesk@homestyles-furniture.com, 888-680-7460, 877-831-0319

88 5549 652

Pantry

For assembly also need the parts and hardware from carton 88 5549 651

(Please refer to the last page of these

instructions for drawer assembly steps.)

Tools required for assembly : Phillips screwdriver

Tools recommended for assembly : Level

Drawer

1 Pc.

Back Panel

2 Pcs.

Front Stretcher

1 Pc.

Base

1 Pc.

Leg

1 Pc.

Leg

1 Pc.

Leg

1 Pc.

Leg

1 Pc.

Back Stretcher

2 Pcs.

Shelf

4 Pcs.

Back Stretcher

2 Pcs.

Back Panel

2 Pcs.

Middle Panel

1 Pc.

Top

1 Pc.

Summary of content (6 pages)

PAGE 1
88 5549 652 Pantry IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damage occurring to the parts. We have taken great care in the design of this product and request that you carefully and strictly follow our assembly instructions to ensure a completed product as it was designed. Part List G. Shelf 4 Pcs. A. Top 1 Pc. J. Middle Panel 1 Pc. D. Back Stretcher 2 Pcs. M. Front Stretcher 1 Pc. E. Back Stretcher 2 Pcs. N.
PAGE 2
Assembly Instructions 3 2/6 IMPORTANT * Please keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future. * Do not tighten up all the Head Cap Bolts until each part is properly assembled. * Use a soft cloth between these parts and the floor. * After assembly item must be level to work properly. Use the included adjustable levelers to level. STEP 1 Insert Cam Lock Screws into pre-drilled holes of Top (A), Side Panels (B), (C), (K), (L), Middle Panel (J).
PAGE 3
Assembly Instructions 3/6 4 V Head Cap Bolt (long) Spring Washer Flat Washer U T N STEP 3 Place Base (N) upside down on a soft cloth. S Attach Legs (S), (T), (U) and (V) to Base (N) with Flat Washers, Spring Washers and Head Cap Bolts (long). (See Figure 3) K M Cam Lock Figure 3 O E N L O Head Cap Bolt (short) STEP 4 Figure 4 Attach Side Panel (K) to Base (N) with Head Cap Bolts (short). (See Figure 4) Attach Back Stretcher (E) to unit. Slide Back Panels (O) into position.
PAGE 4
Assembly Instructions 4/6 5 STEP 5 A B Attach Back Stretchers (D) to Side Panel (B) with Cam Locks. D Attach Back Stretcher (E) to unit. F E D Slide Back Panels (F) into position. C Attach Side Panel (C) to unit with Cam Locks. F Attach Top (A) to the unit with Cam Locks. Cam Lock STEP 6 Turn the unit from Step 4 over to its’ upright position. Attach Middle Panel (J) to the unit from Step 4 with Cam Locks. H Attach unit from Step 5 to unit with Cam Locks.
PAGE 5
Assembly Instructions 5/6 6 STEP 7 Insert Adjustable Pins into the side panels at the desired level. G Place Shelves (G) into position. Slide Drawer (R) into position. G R G G Adjustable Pin STEP 8 Level the unit by adjusting the adjustable levelers on the bottom of the legs. (See Figure 8) Insert Wood Screws (short) into pre-drilled holes in the back panel. Note : Please make sure unit is level before tightening these screws.
PAGE 6
Assembly Instructions 76/6 Drawer (R) R1 R3 STEP 1 R2 Attach R1, R2 and R3 using a Phillips screwdriver and long Wood Screws (4X), tighten halfway. R4 Figure 1 STEP 2 Attach R1, R2 and R4 using long Wood Screws (4X), tighten halfway. (See Figure 1) MAKE SURE ROLLER IS ON THE BACK Slide R5 into grooves in R3 and R4. Be sure to push R5 all the way forward so it meets R1.