Owner's manual

ManualsBrandsHome Styles ManualsComputers5549-18

IMPORTANT NOTE

Carefully remove all the parts from the carton and put

them individually on a soft cloth to prevent scratches

or other damage occurring to the parts.

We have taken great care in the design of this

product and request that you carefully and strictly

follow our assembly instructions to ensure a

completed product as it was designed.

Part List

Home Styles Consumer Assistance: www.homestyles-furniture.com,

servicedesk@homestyles-furniture.com, 888-680-7460, 877-831-0319

88 5549 182

Crescent Hill

Pedestal Desk

(Please refer to the last page of these

instructions for drawer assembly steps.)

Also need the following from carton 88 5549 181 :

Tools required for assembly : Phillips screwdriver Tools recommended for assembly : Level

Drawer

1 Pc.

Drawer

1 Pc.

Drawer

1 Pc.

Drawer

1 Pc.

Keyboard Front

1 Pc.

Keyboard

1 Pc.

Base

1 Pc.

Base

1 Pc.

Door

1 Pc.

Metal Strip

2 Pcs.

Side Panel

1 Pc.

Side Panel

1 Pc.

Middle Panel

1 Pc.

Middle Panel

1 Pc.

Summary of content (10 pages)

PAGE 1
88 5549 182 Crescent Hill Pedestal Desk IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damage occurring to the parts. We have taken great care in the design of this product and request that you carefully and strictly follow our assembly instructions to ensure a completed product as it was designed. Part List G. Drawer 1 Pc. B. Side Panel 1 Pc. C. Side Panel 1 Pc. D. Middle Panel 1 Pc. E. Middle Panel 1 Pc. H.
PAGE 2
Assembly Instructions 3 2/10 IMPORTANT * Please keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future. * Do not tighten up all the bolts until each part is properly assembled. * Use a soft cloth between these parts and the floor. * After assembly item must be level to work properly. Use the included adjustable levelers to level. STEP 1 Insert Cam Lock Screws into pre-drilled holes of Top (A), Side Panels (B) and (C) and Back Panel (F).
PAGE 3
Assembly Instructions 4 3/10 STEP 3 Attach Middle Panel (D) to Base (M) and Middle Panel (E) to Base (N) with Head Cap Bolts. (See Figure 3) D M E N Head Cap Bolt Figure 3 STEP 4 Attach units to Back Panel (F) with Cam Locks. (See Figure 4) Figure 4 Cam Lock F Cam Lock B STEP 5 Attach Side Panels (B) and (C) to unit with Cam Locks and Head Cap Bolts.
PAGE 4
Assembly Instructions 5 4/10 A Cam Lock STEP 6 Turn the unit over to its’ upright position. Attach Top (A) to the unit with Cam Locks. Wood Screw for Hinge K L L Figure 5 STEP 7 Attach Keyboard Front (L) to Keyboard (K) with Wood Screws for Hinge. Attach Pull Handle to Keyboard Front (L) with Machine Screws.
PAGE 5
Assembly Instructions 5/10 6 G O H I Q J Adjustable Pin Figure 6 Figure 7 Figure 8 Figure 9 STEP 8 Insert Adjustable Pins into the side panel and middle panel at the desired level. Place Shelf (Q) into position. Attach Pull Handle to Door (O) with Machine Screws. (See Figure 6) Attach Door (O) by sliding the door lift hinges into the side panel lift hinges. (See Figure 7) Slide Drawers (G), (H), (I), (J) and keyboard into position.
PAGE 6
Assembly Instructions 76/10 Drawer (G) G1 G3 STEP 1 G2 Figure 1 Attach G1, G2 and G3 using a Phillips screwdriver and long Wood Screws (4X), tighten halfway. G4 Attach G1, G2 and G4 using long Wood Screws (4X), tighten halfway. (See Figure 1) MAKE SURE ROLLER IS ON THE BACK STEP 2 Slide G5 into grooves in G3 and G4. Be sure to push G5 all the way forward so it meet G1. (See Figure 2) G1 G3 G5 G4 Figure 2 STEP 3 G5 Insert short Wood Screws (4X) into the pre-drilled holes in G5, tighten screws.
PAGE 7
Assembly Instructions 8 7/10 Drawer (H) H1 H3 STEP 1 H2 Figure 1 Attach H1, H2 and H3 using a Phillips screwdriver and long Wood Screws (4X), tighten halfway. H4 Attach H1, H2 and H4 using long Wood Screws (4X), tighten halfway. (See Figure 1) MAKE SURE ROLLER IS ON THE BACK STEP 2 Slide H5 into grooves in H3 and H4. Be sure to push H5 all the way forward so it meet H1.
PAGE 8
Assembly Instructions 8/10 9 Drawer (I) I1 I3 STEP 1 I2 I4 Attach I1, I2 and I3 using a Phillips screwdriver and long Wood Screws (4X), tighten halfway. MAKE SURE ROLLER IS ON THE BACK Figure 1 Attach I1, I2 and I4 using long Wood Screws (4X), tighten halfway. (See Figure 1) STEP 2 I1 I3 Slide I5 into grooves in I3 and I4. Be sure to push I5 all the way forward so it meet I1.
PAGE 9
Assembly Instructions 10 9/10 Drawer (J) J1 J3 STEP 1 J2 Attach J1, J2 and J3 using a Phillips screwdriver and long Wood Screws (6X), tighten halfway. J4 Attach J1, J2 and J4 using long Wood Screws (6X), tighten halfway. (See Figure 1) Figure 1 STEP 2 Slide J5 into grooves in J3 and J4. Be sure to push J5 all the way forward so it meet J1. (See Figure 2) J3 J1 J5 J4 J5 STEP 3 Insert short Wood Screws (4X) into the pre-drilled holes in J5, tighten screws.
PAGE 10
Assembly Instructions 10/10 11 Keyboard (K) K4 STEP 1 Attach K1 to K4, using a Phillips screwdriver and long Wood Screws (3X), tighten halfway. (See Figure 1) K1 Figure 1 K2 K3 STEP 2 Figure 2 Attach K2 and K3 to unit, using a Phillips screwdriver and long Wood Screws (8X), tighten halfway. (See Figure 2) Tighten all screws used in drawer assembly. Part List K1. Back Part 1 Pc. K2. Side Part 1 Pc. K3. Side Part 1 Pc. K4. Base Part 1 Pc.