Installation Guide

ManualsBrandsHome2O ManualsKitchen FaucetsSchyler Oil Rubbed Bronze 1-Handle Deck Mount Pull-Out Sprayer Kitchen Faucet

04-27-2018

Homewerks Worldwide, LLC • Lake Bluff, IL 60044 • www.homewerksww.com

KITCHEN FAUCET

H60K-51D-CH – Polished chrome nish with pull-out spray

H60K-51D-BN – Brushed nickel nish with pull-out spray

H60K-51D-ORB – Oil rubbed bronze nish with pull-out spray

PACKAGE AND HARDWARE CONTENTS

NSF/ANSI 61

ADA

PART DESCRIPTION

QUANTITY

A Faucet assembly 1

B Gasket 1

C Mounting bolt 2

D Mounting nut 2

E Rubber washer 1

F Lock nut 1

G Screw 2

H Collar 1

SAFETY INFORMATION

Please read and understand this entire manual before attempting to

assemble, operate or install the product.

WARNING

• Protect your eyes with safety glasses when cutting or soldering water supply

lines.

CAUTION

• If you solder the joints during installation, the seats, cartridges, and washers

must be removed before using a ame or the warranty will be voided on

these parts.

• Cover the drain to avoid losing parts.

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare

parts with package contents list and hardware contents. If any part is missing or

damaged, do not attempt to assemble the product.

Contact customer service for replacement parts.

Estimated Assembly Time: 30 minutes

Tools Required for Assembly (not included): Adjustable Wrench, thread sealant

tape, Silicone

Installations may vary depending on how the previous faucet was

installed. Supplies necessary for the installation of the faucet are not

all included; however, they are available wherever plumbing supplies

are sold.

Prior to beginning installation, turn off the hot and cold water lines, then turn

on the old faucet to release built-up pressure. When installing the new faucet,

hand tighten the connector nuts. DO NOT OVERTIGHTEN. Connections

that are too tight will reduce the integrity of the system.

Need Help? Please call our toll-free line at (877) 319-3757 (8 am to 5 pm CST) for additional assistance or service.

Summary of content (8 pages)

PAGE 1
KITCHEN FAUCET H60K-51D-CH – Polished chrome finish with pull-out spray H60K-51D-BN – Brushed nickel finish with pull-out spray H60K-51D-ORB – Oil rubbed bronze finish with pull-out spray NSF/ANSI 61 PACKAGE AND HARDWARE CONTENTS ADA PART DESCRIPTION QUANTITY A Faucet assembly 1 B Gasket 1 C Mounting bolt 2 D Mounting nut 2 E Rubber washer 1 F Lock nut 1 G Screw 2 H Collar 1 B C A D E F G H SAFETY INFORMATION Please read and understand this entire manual before attempting t
PAGE 2
PRODUCT SPECIFICATIONS SPECIFICATIONS SPECIFICATIONS Max. Flow Rate: 1.8 GPM (6.814 LPM) at 60 PSI Ball control cartridge ASME A112.18.1/CSA B125 NSF 61-9 Manufactured to include no more than 0.25% weighted average lead content on wetted surfaces Polished chrome, brushed nickel or oil rubbed bronze finish Total weight of item: 3.90 lbs. ASSEMBLY INSTRUCTIONS 1. urn off water at the supply valve T under the sink or at the main water supply, disconnect the supply line, and remove old faucet.
PAGE 3
ASSEMBLY INSTRUCTIONS 9. Pull sprayer hose out of spout and hold into sink. Flush both water lines by turning handle to a full mixed position, allowing water to run for one minute. 10. Attach spray wand, hand tighten and turn water on. CHECK ALL CONNECTIONS FOR LEAKS. 9 10 TROUBLESHOOTING PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Leaks underneath handle. Bonnet has come loose or O-ring on cartridge is dirty or twisted. 1. M ove the handle to the OFF position.
PAGE 4
ROUGH-IN 10.7" 5.25" 1.85" 7.51" 9.87" 10.36" 8.0" 1/2-14NPSM REPLACEMENT PARTS For replacement parts, call our customer service department at (877) 319-3757, 8 a.m. - 5 p.m., CST, Monday - Friday.
PAGE 5
GRIFO DE LA COCINA H60K-51D-CH - Acabado en cromo pulido con rociador extraíble H60K-51D-BN - Acabado de níquel cepillado con rociador extraíble H60K-51D-ORB - Acabado en bronce pulido con rociador extraíble NSF/ANSI 61 PAQUETE DE HARDWARE Y CONTENIDO ADA PARTE DESCRIPCIÓN CANTIDAD A Montaje de grifería 1 B Empaquetadora 1 C Perno de montaje 2 D Tuerca de montaje 2 E Lavadora de caucho 1 F Tuerca de bloqueo 1 G Tornillo 2 H Collar 1 B C A D E F G H INFORMACIÓN SOBRE LA SEG
PAGE 6
ESPECIFICACIONES DEL PRODUCTO ESPECIFICACIONES ESPECIFICACIONES Caudal de flujo máximo: 6,814 LPM (1,8 GPM) a 60 PSI Cartucho de control de bola ASME A112.18.1/CSA B125 NSF 61-9 Fabricado a incluir no más de 0,25% de contenido de plomo promedio ponderado en superficies mojadas Cromo pulido, níquel cepillado y acabado en bronce aceitado Peso total: 3.90 libras INSTRUCCIONES DE MONTAJE 1.
PAGE 7
INSTRUCCIONES DE MONTAJE 9. Jale la manguera del rociador fuera del surtidor y sostenga en el fregadero. Enjuague ambas líneas de agua girando la manija a una posición completamente mezclada, permitiendo que el agua corra durante un minuto. 10. Coloque la varilla de pulverización, apriete a mano y encender el agua 10 COMPRUEBE TODAS LAS CONEXIONES PARA DETECTAR FUGAS. 9 SOLUCIÓN DE PROBLEMAS PROBLEMA POSIBLE CAUSA ACCIÓN CORRECTIVA Fugas debajo de manejar.
PAGE 8
ÁSPERA EN 10.7" 5.25" 1.85" 7.51" 9.87" 10.36" 8.0" 1/2-14NPSM LISTA DE REPUESTOS Para piezas de repuesto, llame a nuestro departamento de servicio al cliente al (877) 319-3757, 8 a.m.-5 p.m. CST, Lunes - Viernes.