® Chain Saw / Scie De Chaine / Motosierra Timberman® 45cc 18" w/CC UT10910 OPERATOR'S MANUAL MANUEL DU PROPRIÉTAIRE MANUAL PARA EL OPERADOR Homelite Consumer Products, Inc.
WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. CALIFORNIA PROPOSITION 65 For product information, technical help, dealer locations or parts ordering information visit our website at: www.homelite.com.
WARNING: READ THE OWNER'S MANUAL BEFORE USING YOUR CHAIN SAW. FOLLOW ALL INSTRUCTIONS FOR SAFE OPERATION. ADVERTENCIA: LEA EL MANUAL DEL PROPIETARIO ANTES DE USAR SU SIERRA DE CADENA. SIGA TODAS LAS INSTRUCCIONES PARA UN FUNCIONAMIENTO SEGURO. AVERTISSEMENT: AVANT D’UTILISER CETTE TRONÇONNEUSE, LIRE LES INSTRUCTIONS CONTENUES DANS LE MANUEL DU PROPRIÉTAIRE. POUR UN FONCTIONNEMENT EN TOUTE SÉCURITÉ, EN RESPECTER TOUTES LES INSTRUCTIONS.
• • • • • • • Make sure that the area in which you are cutting is free from obstructions. Do not let the nose of the guide bar contact a log, branch, fence, or any other obstruction that could be hit while you are operating the saw. Keep SAFE-T-TIP® Anti-Kickback Nose Guard properly mounted on the guide bar to prevent kickback. Always cut with the engine running at full speed. Fully squeeze the throttle trigger and maintain a steady cutting speed. Do not overreach or cut above chest height.
RECOMMENDED BAR AND CHAIN COMBINATIONS COMBINAISONS RECOMMANDÉES DE GUIDE-CHAÎNE ET DE CHAÎNE COMBINACIONES RECOMENDADAS DE BARRAS Y CADENAS For .325 Pitch Chain RECOMMENDED BAR AND CHAIN COMBINATIONS COMBINAISONS RECOMMANDÉES DE GUIDE-CHAÎNE ET DE CHAÎNE COMBINACIONES RECOMENDADAS DE BARRAS Y CADENAS LENGTH OF BAR AND STYLE OF TIP TYPE D’EXTRÉMITÉ ET LONGUEUR DU GUIDE-CHAÎNE LONGITUD DE LA BARRA Y ESTILO DEL EXTREMO GUIDE BAR NO. GUIDE-CHAÎNE Nº BARRA DE GUIA NO. CHAIN PART NO.
A B M N C L D K E O J F I H A. B. C. D. E. F. G. H. I. J. K. L. M. N. O. Front hand guard Front handlebar Cylinder cover Throttle lock button for starting Trigger lock Rear handle Throttle trigger Ignition Switch (I) On / (O) Off Fuel mix cap Chain oil cap Starter/Fan housing Starter grip Safe-t-tip® Primer bulb Choke lever A. B. C. D. E. F. G. H. I. J. K. L. M. N. O.
REMARQUE : Les personnes souffrant de troubles de la circulation sanguine qui sont exposées aux vibrations prolongées d’outils motorisés par moteur à essence peuvent subir des dommages aux nerfs et vaisseaux sanguins des doigts, mains et poignets, ou des enflures anormales. Une utilisation prolongée par temps froid a causé des dommages aux vaisseaux sanguins de personnes en bonne santé.
• • • • • • Always use caution when handling fuel. Move the chain saw at least 10 feet (3m) from the fueling point before starting the engine. Do not operate a chain saw with one hand! Serious injury to the operator, helpers, bystanders, or any combination of these persons may result from one-handed operation. A chain saw is intended for two-handed use. Never let anyone use your chain saw who has not received adequate instructions in its proper use.
MAINTENANCE • Never operate a chain saw that is damaged, ENTRETIEN • Ne jamais se MANTENIMIENTO • No opere nunca una • • servir d’une tronçonneuse endommagée, mal réglée ou qui n’est pas complètement et solidement assemblée. Bien vérifier que la chaîne s’arrête de tourner lorsque l’on relâche la gâchette de l’accélérateur. improperly adjusted, or is not completely and securely assembled. Be sure that the saw chain stops moving when the throttle control trigger is released.
FRONT HAND GUARD PROTÈGE-MAIN AVANT Your saw has a factory-installed front hand guard to prevent contact with the chain if your hand slips off the front handle. Do not remove the front hand guard. Maintain the guard in good condition and do not use the guard as a hand grip. Replace it if damaged or broken. L’appareil est doté à l’avant d’un protège-main installé à l’usine pour empêcher un contact avec la chaîne si la main glisse de la poignée avant.
LOW KICKBACK SAW CHAIN CHAÎNE À FAIBLE REBOND The rakers (depth gauges) ahead of each cutter can minimize the force of a kickback reaction by preventing the cutters from digging in too deeply at the kickback zone. Only use replacement chain that is equivalent to original chain or has been certified as low kickback chain per ANSI B175.1. Low kickback saw chain is chain that has met the kickback performance requirements of ANSI B175.
GUIDE BAR AND CHAIN ASSEMBLY ASSEMBLAGE DE LA CHAÎNE ET DU GUIDE-CHAÎNE DANGER Never start your engine unless guide bar, chain, drivecase cover and clutch drum are installed. Without all these parts in place, the clutch can fly off or explode. 1. Always put the switch to "O" stop before you do any work on the saw. 2. Remove the mounting nuts (A) (5/8" wrench required), drive case cover (B), and outer guide bar plate (C). 3. Wear gloves when handling the chain as it is sharp.
CHAIN TENSION TENSION DE LA CHAÎNE TENSION DE LA CADENA 1. Stop the engine before setting tension. Turn the adjusting screw (I) clockwise to move the guide bar outward until the chain is tight to the bar but can still be pulled around the bar by hand. See Illustration A. Tighten guide bar nut(s) securely to lock in position. 2. Chain must be re-tensioned whenever the drive link tangs hang out of the bar groove. See Illustration B. 3.
PREPARING FOR USE PRÉPARATION À L’EMPLOI PREPARACION PARA EL USO FUELING REMPLISSAGE EN CARBURANT COMBUSTIBLE This product is powered by a 2-cycle engine and requires pre-mixing gasoline and 2-cycle oil. Premix unleaded gasoline and 2-cycle engine oil in a clean 1 gallon container approved for gasoline. RECOMMENDED FUEL: THIS ENGINE IS CERTIFIED TO OPERATE ON UNLEADED GASOLINE INTENDED FOR AUTOMOTIVE USE. Mix HOMELITE® Premium Exact Mix™ Oil with gasoline according to the instructions on the package.
CHAIN OIL SYSTEM ® 1. Use HOMELITE Bar and Chain Oil. It is designed for chains and chain oilers and is formulated to perform over a wide temperature range with no dilution required. If not available, use any new SAE-30 weight engine oil. NOTE: Used, dirty or otherwise contaminated oils must not be used. 2. Fill the oil tank every time engine is fueled. 3. The automatic oil pump is a positive displacement pump operated through gears driven off the crankshaft assembly.
9. Pull starter until engine tries to run. (No more than 6 pulls.) 10.Move choke lever to half choke position (G) and pull starter until engine runs. 11.Move choke lever to run position (H). Squeeze the trigger and then release. This unlatches the trigger and gives you control of throttle for cutting. 12.Now you are ready to pick up the saw. Use the proper grip and hold onto both handles. 13.Flip the switch to "O" stop position when you wish to stop the engine. Special Starting Situations 14.
PREPARATION FOR CUTTING PROPER GRIP ON HANDLES 1. Wear non-slip gloves for maximum grip and protection. 2. Maintain a proper grip (A) on the saw whenever the engine is running. The fingers should encircle the handlebar and the thumb is wrapped under the handlebar. This grip is least likely to be broken (by a kickback or other sudden reaction of the saw). Any grip in which the thumb and fingers are on the same side of the handle (B), is dangerous because a slight kick of the saw can cause loss of control.
PROPER CUTTING STANCE • Weight should be balanced on both feet - feet • • • on solid ground. Keep arm with elbow locked in a "straight arm" position (A) to withstand any kickback force. Your body should always be to the left of the chain line (B). Thumb on underside of handlebar (C). POSITION CORRECTE DU CORPS POUR LA COUPE • Le poids du corps doit être réparti également • • • sur les deux pieds, les pieds reposant sur un sol ferme.
WORK AREA PRECAUTIONS • Cut only wood or materials made from wood; no • • • • • sheet metal, no plastics, no masonry, no nonwood building materials. Never allow children to operate your saw. Allow no person to use this chain saw who has not read this Owner's Manual or received adequate instructions for the safe and proper use of this chain saw. Keep everyone - helpers, bystanders, children, and animals a safe distance from the cutting area.
UNUSUAL HAZARDOUS CONDITIONS • Do not fell trees during periods of high wind or CONDITIONS PARTICULIÈREMENT DANGEREUSES • Ne pas abattre d’arbres en période de grand heavy precipitation. Wait to do your cutting until the hazard has ended. Do not cut down trees having an extreme lean or large trees that have rotten limbs, loose bark, or hollow trunks. Have these trees pushed or dragged down with power equipment. Then you can cut them up.
3. Cut a notch (C) about 1/3 the diameter of the trunk in the side of the tree. Make the cuts of the notch so they intersect at a right angle to the line of fall . See Illustration 5. This notch should be cleaned out to leave a straight line. To keep the weight of the wood off the saw, always make the lower cut of the notch before the upper cut. 4. The backcut is always made level and horizontal, and at a minimum of 2 inches (5 cm) above the horizontal cut of the notch (D). 5.
During bucking operations always stand on the uphill side so that the cut-off section of the log can not roll over you. A wedge can be used on large diameter logs to hold the cut open (See illustration). Pendant le tronçonnage sur un terrain en pente, toujours se placer en amont pour éviter d’être heurté au cas où la section coupée se mettrait à rouler. Dans le cas d’un rondin de gros diamètre, on peut utiliser un coin pour maintenir l’entaille ouverte (voir figure).
LIMBING AND PRUNING ÉBRANCHAGE ET ÉLAGAGE • • • • • Work slowly, keeping both hands on the saw with a firm grip. Maintain secure footing and balance. Keep the tree between you and the chain while limbing (A). Cut from the side of the tree opposite the branch you are cutting. Do not cut from a ladder, this is extremely dangerous. Leave this operation for professionals. Do not cut above chest height as a saw held higher is difficult to control against kickback.
BAR AND CHAIN MAINTENANCE Use only HOMELITE ® Raker low-kickback chain on this saw. This fast-cutting chain will provide kickback reduction when properly maintained. For smooth and fast cutting, Raker chain needs to be maintained properly. The chain requires sharpening when the wood chips are powdery, the chain must be forced through the wood during cutting, or the chain cuts to one side. During maintenance of your chain, consider the following: 1.
HOW TO FILE THE CUTTERS AFFÛTAGE DES COUTEAUX COMO LIMAR LOS CORTADORES Be careful to file all cutters to the specified angles and to the same length, as fast cutting can be obtained only when all cutters are uniform. 1. Clamp the middle of the guide bar in a vice. Be careful that you do not pinch the guide bar rails or the chain will not move freely in the groove. 2. Tighten the chain tension enough that the chain doesn't wobble. Do all of your filing at the mid-point of the bar.
RAKER (DEPTH GAUGE) CLEARANCE DÉGAGEMENT DES LIMITEURS D’ÉPAISSEUR DE COPEAUX 1. The rakers (D, see page 24) should be maintained at a clearance (A, see page 24) between .020" (0.5 mm) and .018 (0.46 mm). Depth gauge tool #D06885 can be used for checking the raker clearances. 2. Every time the chain is filed, check the raker clearance. 1. Le dégagement des limiteurs d’épaisseur de copeaux (D, voir page 24) doit être maintenu entre 0,5 et 0,46 mm (0,020 et 0,018 po) (A, voir page 24).
REGULAR MAINTENANCE ENTRETIEN RÉGULIER MANTENIMIENTO REGULAR AIR FILTER MAINTENANCE ENTRETIEN DU FILTRE À AIR For proper performance and long life, keep air filter clean. Maintenir le filtre à air propre pour assurer un bon fonctionnement et une bonne durée de vie. MANTENIMIENTO DEL FILTRO DEL AIRE TO INSPECT AND CLEAN OR REPLACE THE AIR FILTER INSPECTION ET NETTOYAGE, OU REMPLACEMENT DU FILTRE À AIR NOTE Always clean the air filter before making any mixture adjustments of the carburetor. 1.
SPARK ARRESTOR PARE-ÉTINCELLES RECUPERADOR DE CHISPAS 1. Always keep the muffler (A) and spark arrestor (B) on your saw in good condition. A faulty spark arrestor screen can create a fire hazard. 2. The spark arrestor screen is retained by the deflector (C). Remove the deflector screw (D) to access screen. 3. Replace the spark arrestor screen if it is cracked or otherwise deteriorated. 1. Maintenir le silencieux d’échappement (A) et le pare-étincelles (B) en bon état.
TROUBLESHOOTING IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM CONTACT YOUR AUTHORIZED SERVICING DEALER. PROBLEM Engine will not start: (Make sure RUN/STOP switch is in RUN “I” position.) POSSIBLE CAUSE SOLUTION 1. NO SPARK. 1. Check Spark. Remove cylinder cover. Remove spark plug from cylinder. Reattach the spark plug wire and lay spark plug on top of muffler or cylinder. Pull the starter rope and watch for spark at spark plug tip. If there is no spark, repeat test with a new spark plug. 2.
LOCALISATION DES PANNES SI LES SOLUTIONS SUIVANTES NE PERMETTENT PAS DE RÉSOUDRE LE PROBLÈME, S’ADRESSER À UN DÉPOSITAIRE AGRÉÉ POUR LES RÉPARATIONS. PROBLÈME Le moteur ne démarre pas : Vérifier que l’interrupteur Marche/ Arrêt est dans la position “I” (Marche) CAUSE POSSIBLE 1. PAS D’ÉTINCELLE 2. PAS DE CARBURANT. 3. LE MOTEUR EST NOYÉ. SOLUTION 1. Vérifier la bougie. Enlever la capot de cylindre. Démonter la bougie.
RESOLUCION DE PROBLEMAS SI ESTAS SOLUCIONES NO RESUELVEN EL PROBLEMA, PONGASE EN CONTACTO CON SU AGENTE DE SERVICIO AUTORIZADO. PROBLEMA POSIBLE CAUSA El motor no se pone en marcha: (Asegúrese de que el conmutador de PUESTA EN MARCHA/PARADA esté en la posición RUN (FUNCIONAMIENTO) “I”) 1. NO DA CHISPA 2. NO HAY COMBUSTIBLE 3. MOTOR AHOGADO SOLUCION 1. Compruebe la chispa. Retire la cubierta del cilindro. Saque la bujía del cilindro.
HOMELITE® PRODUCTS - LIMITED WARRANTY Homelite Consumer Products, Inc. warrants to the original retail purchaser that this Homelite® Product is free from defects in material and workmanship and agrees to repair or replace, at Homelite Consumer Products, Inc.
MANUFACTURER'S WARRANTY COVERAGE: The 1995 and later small off-road engines are warranted for two years in California. In other states, 1997 and later model year nonroad engines are also warranted for two years. If any emission-related part on your engine is defective, the part will be repaired or replaced by Homelite Consumer Products, Inc. free of charge.
PRODUIT HOMELITE® - GARANTIE LIMITÉE HomeliteConsumer Products, Inc. garantit à l’acquéreur original (vente au détail) que ce produit Homelite® ne présente pas de défauts de matière ou de main d’oeuvre, et s’engage à réparer ou à remplacer (à la discrétion de Homelite Consumer Products, Inc.) gratuitement tout produit défectueux pendant la durée ci-dessous à compter de la date de l’achat : • Un an si le Produit est utilisé dans le cadre personnel, familial ou domestique.
GARANTIE DU FABRICANT : En Californie, les petits moteurs de véhicules tout terrain datant de 1995 et ultérieurs bénéficient d’une garantie de deux ans. Dans les autres États, les moteurs de véhicules hors route datant de 1997 et ultérieurs bénéficient aussi d’une garantie de deux ans. En cas de défaillance d’une pièce faisant partie du dispositif anti-pollution, la pièce sera gratuitement réparée ou remplacée par Homelite Consumer Products, Inc.
PRODUCTOS HOMELITE® - GARANTIA LIMITADA La Homelite Consumer Products, Inc. le garantiza al comprador original al por menor que este Producto Homelite® se encuentra libre de defectos de material y mano de obra, y acepta reparar o reemplazar, a discreción de Homelite Consumer Products, Inc.
COBERTURA DE GARANTIA DEL FABRICANTE: Los motores de vehículos para uso fuera de la carretera y todo terreno fabricados en 1995 y años posteriores se encuentran garantizados durante un período de dos años en California. En otros estados, los motores de vehículos para uso fuera de la carretera y todo terreno fabricados en 1997 y los modelos de años posteriores se encuentran asimismo garantizados durante un período de dos años.
PRODUCT INFORMATION NO. PART NO. A. UP 00126 B. UP 00125 UP 04213 UP 04033 C. UP 07865 D. UP 06753 E. UP 06749 F. UP 06754 G. H. I. J. K. L. M. UP DA DA A UP UP UP UP UP UP UP N. A O. A P. A Q. UP R.
ACCESSORY SHEET LISTE D’ ACCESSOIRES HOJA DE ACCESORIOS If your Homelite® dealer does not have these accessories, you may order direct from PDQ sales in the continental USA using this form or CALL: Si votre concessionnaire PDQ ne dispose pas de ces accessoires, vous pouvez les commander directement auprès de Homelite® sur le territoire continental des États-Unis , soit à l'aide de cette page soit PAR TÉLÉPHONE AU NUMÉRO SUIVANT: En caso de que su distribuidor de productos PDQ no tenga estos accesorios, ust
Exact Mix TM Oil Huile Exact Mix TM Aceita de Exact Mix TM No. US $ 01231 D .............................................................. # $14.97 Three Pack (mixes 18 gallons of fuel). Carton de 3 flacons (pour 18 gallons de carburant). Tres paquetes (mezcla 18 galones de gasolina). Specially developed 2-cycle oil to be mixed with gasoline for lubricating 2-cycle air-cooled engines. The bottle design has a built-in chamber for quick, easy measuring of the exact amount of oil.
