Assembly Instructions Instrucciones de Ensamblaje 120mns SAVE THESE INSTRUCTIONS GUARDE ESTAS INSTRUCCIONES 3-Drawer Desk Escritorio de 3 cajones C1720023 Do Not Return! No Vuelvas! Email or call customer service for help first. Envie correo electrónico o llame al servicio para obtener ayuda primero. 1-883-907-1099 Monday-Friday 9am - 4pm CST customer@primahomefurnishings.
WARNING This product can expose you to chemicals including Formaldehyde, which is known to the State of California to cause cancer or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov/furniture ADVERTENCIA Este producto puede exponerlo a sustancias quím icas, incluyendo el formaldehído, el cual es conocido en el estado de California como causante de cáncer, defectos de nacimiento u otros daños reproductivos. Para obtener más información vaya a www.P65Warnings.ca.
Helpful advice 1. Follow the assembly instructions carefully. 2. Check to ensure all parts, fasteners and hardware are present. 3. To prevent product damage, assemble the furniture on top of the carton. 4. Clean surface of furniture with a duster or damp cloth only. Do not use abrasive cleaners. Consejos útiles 1. Siga a tentamente las instrucciones de montaje. 2. Asegúrese de que la caja contiene todas las piezas, sujeciones y materiales. 3. Monte el mueble sobre la caja para evitar dañarlo. 4.
Parts list/Lista de piezas ITEM DESCRIPTION 20 Upper left drawer back Tablero posterior del cajón superior izquierdo 1 21 Upper left drawer bottom Tabrero inferior del cajón superior izquierdo 2 22 Upper left drawer front Tablero frontal del cajón superior izquierdo 1 23 Lower drawer side left Tablero izquierdo del cajón inferior 1 24 Lower drawer side right Tablero derecho del cajón inferior 1 25 Lower drawer back Tablero posterior del cajón inferior 1 26 Lower drawer front Tab
Hardware/Lista de materiales ITEM IMAGE DESCRIPTION DESCRIPCIÓN QUANTITY A Wood dowel Pernos Madera 20 B Cam bolt (large) Perno Metálico (grande) 14 C Cam lock (large) Bloqueo metálico (grande) 14 D Φ3.5*12 mm Screw Φ3.
Hardware/Lista de materiales ITEM IMAGE DESCRIPTION DESCRIPCIÓN M Φ4.7*12.5 mm Screw Φ4.7*12.5 mm Tornillo 8 N Φ3.8*35 mm Screw Φ3.
Har Hardware/Lista de materiales ITEM IMAGE Y DESCRIPTION DESCRIPCIÓN QUANTITY Φ3*16 mm Screw Φ3*16 mm Tornillo 8 Note/Rema que/Nota r El uso del tornillo incorrecto puede provocar daños al producto. Antes de iniciar la operación de Using the wrong screw will cause damage. Before you begin assembly check to ensure all parts are present. Screws are actual size. tornillo.
Necessary tools/Herramientas necesarias Glue Glue not enclosed (We recommend to apply some glue into holes before inserting wood dowels.) Colle non fournie (Nous vous recommandons d’appliquer quelques gouttes de colle dans les trous avant notd’y included ( Weles recommend apply some glue into holes before inserting wood dowels .) introduire chevilles detobois.) Cola, nomadera.) incluida (Le recomendamos colocarunas gotas de cola en los orificios antes de insertar las clavijas de madera.
Attention: In order to help your assembly, do not lock the screw tightly until you have assembled all the other parts. Atención: Con el fin de facilitar su montaje, no apretar el tornillo firmemente hasta que haya ensamblad o todas las otras partes. Step 1/Paso 1 Insert 4 wood dowels (A) into the edge of the fixed shelf (1). Insert 2 wood dowels (A) into the edge of the rail (2). Inserte 4 Pernos Maderas (A) en el estante izquierdo (1), y 2 Pernos en la Barra bajo del Cajón (2).
Step 3/Paso 3 Insert 3 cam locks (C) into fixed shelf (1) and rail (2) to combine them with gable left (3). Make sure cam locks are fully insert and in correct orientation. Conecte el Estante izquierdo (1),la Barra inferior del Cajón (2) al Tablero izquierdo (3) con 3 Bloqueos metálicos (grandes) (C). Cx3 2 C 3 Step 4/Paso 4 Insert 4 wood dowels (A) and 3 cam bolts (B) into the divider (4). Align 2 right glider (F) with the holes on the divider (4), then secure with 6 screws (D).
Step 5/Paso 5 Insert 3 cam locks (C) into the holes on fixed shelf (1) and rail (2) to combine the divider (4) with them. Make sure cam locks are fully insert and in correct orientation. Conecte el Tablero vertical (4) al ensamblaje con 3 Bloqueos metálicos (grandes) (C). 4 Cx3 C 2 3 Step 6/Paso 6 Align the dowels on gable left (3) and gable right (4) with the holes on the left bottom (5), then combine them with 4 screws (G). Conecte el Tablero izquierdo inferiorr (5) al ensamblaje con 4 Tornillos (G).
Step 7/Paso 7 Insert 2 cam bolts (B) into the divider (4). Align 1 left glide (E) with the holes on the divider (4), then secure with 3 screws (D). Make sure the first hole you align is correct. Inserte 2 Pernos metálicos (grandes) (B) en fuera del Tablero vertical (4), Inserte el Planeador izquierdo(E) en el Tablero vertical (4) con 3 Tornillos (D) Tenga en cuenta que la posición del primer agujero sea correcto.
Step 9/Paso 9 Insert 2 cam locks (C) into the right bottom (6) to combine it with the divider (4). Insert 2 brackets (H) into the divider (4) with 2 screws (I). Conecte el Marco derecho inferior (6) al Tablero vertical (4) con 2 Bloqueos metálicos (grandes) (C), Insterte 2 Chapas en el Tablero vertical (4) con 2 Tornillos. Cx2 Ix2 I 4 H 6 C Step 10/Paso 10 Insert 4 wood dowels (A) into the large holes on the edge of gable right (7).
Step 11/Paso 11 Align the dowels on the gable right (7) with the holes on the right bottom (6), then combine them with 2 screws (G). Conecte el Tablero derecho (7) al Marco derecho inferior (6) con 2 Tornillos (G). Gx2 7 6 G Step 12 /Paso 12 Insert left back panel (8) and right back panel (9) into the bottom. Inserte el Tablero izquierdo posterior (8) e Tablero derecho posterior (9).
Step 13/Paso 13 Insert 2 cam bolts (B) into the smaller holes on the top (10). Inserte 6 Pernos metálicos (grandes) (B) en el Panel superior (10). Bx6 B 10 Step 14/Paso 14 Align the top (10) with the holes on gable left (3) and gable right (7), then combine them with 6 cam locks (C). Conecte el Panel superior (10) al ensamblaje con 6 Bloqueos metálicos (grandes) (C).
Step 15/Paso 15 Insert 2 bolts (W) through the connecting pipe (11) and into the right leg (12), then tighten with a hex wrench (V). Utilice una llave Allen (V) y 2 Tornillos (W) para conectar el Tubo de conexión (11) al Soporte derecho (12). 11 V V W Wx2 12 Step 16/Paso 16 Insert left leg (13) and right leg (12) into the stand assembly with 7 bolts (U) and 7 washers (J), then tighten with a hex wrench (V).
Step 17/Paso 17 Combine connecting pipe (11) with divider (4) with 2 screws (I) and 2 washers (J). Conecte el Tubo de conexión (11) al Tablero vertical (4) con 2 Tornillos (I) y 2 Arandelas planas (J). Ix2 J Jx2 I 4 11 Step 18/Paso 18 Insert 8 back buttons (Y) into the left back panel (8) and right back panel (9) with 8 screws (I). Utilice 8 Tornillos (Y) para bloquear 8 Botones de retrocesos (X) al Tablero izquierdo posterior (8) e Tablero derecho posterior (9).
x2 Step 19/Paso 19 Align 1 left glide (E) with the holes on the upper drawer side left (14), then secure with 3 screws (D). Align 1 right glide (F) with the holes on the upper drawer side right (15), then secure with 3 screws (D). Conecte el Planeador izquierdo (E) al Tablero izquierdo del cajón superior (14) con 3 Tornillos (D),Conecte Planeador derecho (F) al Tablero derecho del cajón superior (15) con 3 Tornillos (D).
Step 21/Paso 21 Insert upper right drawer bottom (18) into the assembly part. Insert 1 cam bolt (S) into the upper right drawer front (19). Insterte el Tablero inferior del cajón derecho (18), Bloquee el Tornilla metálico (Pequeño) (S) al Tablero frontal del cajón derecho (19). Sx1 18 S 19 Step 22/Paso 22 Insert handle (Q) into the upper right drawer front (19). Use 1 cam lock (T) to combine upper right drawer front (19) with upper right drawer bottom rail (17).
Step 23/Paso 23 Combine upper drawer side left (14) and upper drawer side right (15) with upper left drawer back (20) with 4 screws (N). Insert small drawer connector (K) into the upper drawer side left (14) and upper drawer side right (15) with 2 screws (L). Conecte el Tablero izquierdo del cajón superior (14), el Tablero derecho del cajón superior (15) al Tablero posterior del cajón superior izquierdo (20) con 4 Tornillos (N).
Step 25/Paso 25 Insert handle (Q) to the upper left drawer front (22) with 2 bolts (P). Secure small drawer connector (K) to the upper left drawer front (22) with 2 screws (M). Conecte el Tirador (Q) al Tablero frontal del cajón superior izquierdo (22) con 2 Tornillos (P), y bloquee los Conectores de plástico (pequeños) (K) con 3 Tornillos (M), y cerralos bien. Mx2 Px2 M Qx1 P Q 22 Step 26/Paso 26 Align 1 left glide (E) with the holes on the lower drawer side left (23), then secure with 3 screws (D).
Step 27/Paso 27 Combine lower drawer side left (23) and lower drawer side right (24) with lower drawer back (25) with 4 screws (N). Insert small drawer connector (K) into lower drawer side left (23) and lower drawer side right (24) with 4 screws (L).
Step 29/Paso 29 Insert handle (Q) into lower drawer front (26) with 2 screws (P). Secure large drawer connector (O) to lower drawer front (26) with 4 screws (M). Attach plastic file hanger (R) to lower drawer side left (23) and lower drawer side right (24). Conecte el Tirador (Q) al Tablero frontal del cajón inferior (26) con 2 Tornillos (P), Bloquee los Conectores de plástico (grandes) (O) con 4 Tornillos (M),y cerralos bin.
Maximum weight capacities/Capacidades de carga máxima 3kg 6.61lbs. 45kg 99.21lbs. 1.5kg 3.31lbs. 12kg 26.46lbs. 6.5kg 14.33lbs. WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. －This product is intended to hold maximum weight indicated. Exceeding the maximum weight will result in instability and may cause serious injury.
1 YEAR WARRANTY BASIC WARRANTY: Homestar® furniture is warranted by Homestar Corporation (Homestar) to the original purchaser for a period of one year from the date of purchase, subject to the following conditions and limitations. 1. Install and operate this item in accordance with the Installation and operating instructions provided with the product at all times. Any alteration, willful abuse, accident, or misuse of the product shall nullify this warranty. 2.
