Use and Care Manual

ManualsBrandsHOMESTYLES ManualsFurnitureAmericana Pantry in White

Hardware List

Part List

Home Styles Customer Service: www.homestyles-furniture.com,

servicedesk@homestyles-furniture.com,

888-680-7460, 877-831-0319

Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit

5004 692-

Pantry

IMPORTANT

Carefully remove all the parts from the carton and

place them individually on a soft cloth to prevent

scratches or other damage.

Carefully and strictly follow these assembly instructions

to ensure a completed product as designed.

Do not use power tools above 8 volts to assemble.

Cam Lock Screw

24 pcs. (+1 extra)

Cam Lock

24 pcs. (+4 extra)

M3.5x16

Wood Screw

16 pcs. (+1 extra)

Adjustable Pin

16 pcs. (+1 extra)

Knob

4 pcs.

M4x25

Machine Screw

4 pcs.

Top

1 pc.

Side Panel

2 pcs.

Side Panel

2 pcs.

Back Stretcher

4 pcs.

Back Upright

2 pcs.

Back Panel

4 pcs.

Middle Panel

1 pc.

Base

1 pc.

Shelf

4 pcs.

Door

2 pcs.

Door

2 pcs.

Summary of content (7 pages)

PAGE 1
5004-692 Pantry IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List A. Top 1 pc. B. Side Panel 2 pcs. C. Side Panel 2 pcs. E. Back Upright 2 pcs. F. Back Panel 4 pcs. J. Door 2 pcs. K. Door 2 pcs. G. Middle Panel 1 pc. D. Back Stretcher 4 pcs. I.
PAGE 2
Assembly Instructions 2/6 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Make sure unit is level before tightening these screws. The unit must be level to work properly. Use the included adjustable levelers to level. Cam Lock Screw STEP 1 Insert Cam Lock Screws into pre-drilled holes in Top (A), Side Panels (B), (C), Middle Panel (G) and Base (H), then tighten.
PAGE 3
Assembly Instructions 3/6 STEP 2 Cam Lock D Attach Back Stretcher (D) to Side Panel (B) with Cam Lock. (See Figure 2) Attach Back Upright (E) to Stretcher (D). F Slide Back Panels (F) into position. F B Attach Back Stretcher (D) to unit with Cam Lock. E C Attach Side Panel (C) to unit with Cam Locks. D Cam Lock Figure 2 STEP 3 G Cam Lock Attach unit to Base (H) with Cam Locks. Attach Doors (J) and (K) to unit by sliding door hinges into side panel hinges.
PAGE 4
Assembly Instructions 4/6 Cam Lock D STEP 4 Attach Back Stretcher (D) to Side Panel (B) with Cam Lock. (See Figure 2) F Attach Back Upright (E) to Stretcher (D). F B E Slide Back Panels (F) into position. C Attach Back Stretcher (D) to unit with Cam Lock. Attach Side Panel (C) to unit with Cam Locks. D Cam Lock STEP 5 Attach unit from Step 4 to unit from Step 3 with Cam Locks.
PAGE 5
Assembly Instructions 5/6 A STEP 6 Cam Lock Insert Adjustable Pins into side panels at desired level. Adjustable Pin Place Shelves (I) into position. Attach Doors (J) and (K) to unit by sliding door hinges into side panel hinges. I Attach Knobs to Doors (J) and (K) with Machine Screws. (See Figure 4) J I K Attach Top (A) to unit with Cam Locks. Adjustable Pin Machine Screw Knob I J I K Figure 4 STEP 7 Level unit by adjusting the adjustable levelers on bottom of unit.
PAGE 6
Assembly Instructions 6/6 IMPORTANT To help reduce the risk of the unit tipping over, the Tipover Restraint must be installed following these instructions exactly. STEP 8 Anchor in wall Place unit at desired location. Bracket on wall Pre-drilled hole at top of unit Wall Screw Wood Screw 3/8” wall hole Drill a 3/8” hole in wall in-line with pre-drilled hole at top of unit. Move unit. Tie end Insert Anchor into the wall hole and attach Bracket with Wall Screw.
PAGE 7
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.