Use and Care Manual

ManualsBrandsHOMESTYLES ManualsBathBarnside Metro 25 in. W Over the Toilet Space Saver in Driftwood Gray

Part List

5053-106

Over the Commode Stand

IMPORTANT

Carefully remove all the parts from the carton and

place them individually on a soft cloth to prevent

scratches or other damage.

Carefully and strictly follow these assembly instructions

to ensure a completed product as designed.

Do not use power tools above 8 volts to assemble.

Top

1 pc.

Shelf

2 pcs.

Shelf

1 pc.

Side Frame

1 pc.

Side Frame

1 pc.

Side Frame

1 pc.

Side Frame

1 pc.

Front Rail

2 pcs.

Back Rail

2 pcs.

Hardware List

Anchor

2 pcs. (+1 extra)

Bracket

2 pcs. (+1 extra)

Tool(s) required for assembly: Phillips screwdriver, Level, Pencil, Drill (8 volts or less), 3/8” Drill Bit

M3.5x40

Wall Screw

2 pcs. (+1 extra)

Hex Wrench

1 pc.

Small Hex Wrench

1 pc.

M6x16

Head Cap Bolt

32 pcs. (+1 extra)

Spring Washer

32 pcs. (+1 extra)

Flat Washer

24 pcs. (+1 extra)

Flat Washer (large)

8 pcs. (+1 extra)

Adjustable Pin

8 pcs. (+1 extra)

styles Customer Service: www.homestylesfurniture.com,home

servicedesk@homestylesfurniture.com,

888-680-7460

Summary of content (7 pages)

PAGE 1
5053-106 Over the Commode Stand IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List A. Top 1 pc. B. Shelf 2 pcs. C. Shelf 1 pc. D. Side Frame 1 pc. H. Front Rail 2 pcs. E. Side Frame 1 pc. F. Side Frame 1 pc. G. Side Frame 1 pc. I. Back Rail 2 pcs.
PAGE 2
Assembly Instructions 2/6 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Hex Wrench as the bolts may need to be tightened in the future.
PAGE 3
Assembly Instructions 3/6 E G STEP 2 Attach Side Frame (E) to Side Frame (G) with Flat Washer, Spring Washer and Head Cap Bolt, tightening bolt only halfway. Attach unit to unit from Step 1 with Flat Washers, Spring Washers and Head Cap Bolts, tightening bolts only halfway.
PAGE 4
Assembly Instructions 4/6 A C Flat Washer (large) Spring Washer Head Cap Bolt STEP 3 Attach Top (A) and Shelf (C) to unit with Flat Washers (large), Spring Washers and Head Cap Bolts, tightening bolts only halfway. Tighten all bolts used in all steps.
PAGE 5
Assembly Instructions 5/6 B Adjustable Pin B Figure 3 STEP 4 Turn unit to its upright position. Insert Adjustable Pins into unit at desired level. (See Figure 3) Place Shelves (B) into position. Level unit by adjusting the adjustable levelers on bottom of unit. (See Figure 4) Note: Unit must be level to work properly.
PAGE 6
Assembly Instructions 6/6 IMPORTANT To help reduce the risk of the unit tipping over, the Tipover Restraint must be installed following these instructions exactly. STEP 5 Place unit at desired location. Loosen slightly Head Cap Bolts attaching Brackets to unit. Slide Brackets to wall, then retighten Head Cap Bolts. Mark wall with pencil through holes in Brackets. (See Figure 5) Move unit. 3/8” wall hole Drill 3/8” holes in wall at marks, then insert Anchors into the wall holes.
PAGE 7
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.