20 05100 0002 Buffet IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List G. Back Stretcher 1 pc. H. Back Stretcher 1 pc. A. B. C. E. D. F. Side Panel Side Panel Middle Panel Middle Panel Back Panel Back Upright 1 pc. 1 pc. 1 pc. 3 pcs. 1 pc. 2 pcs. K.
Assembly Instructions 2/8 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Hex Wrench as the bolts may need to be tightened in the future. STEP 1 Insert Cam Lock Screws into pre-drilled holes in Side Panels (A), (B) and Middle Panels (C), (D), then tighten.
Assembly Instructions 3/8 STEP 3 Attach Back Stretcher (H) to unit with Cross Dowels and Head Cap Bolts (long). (See Figure 3) E E Attach Back Uprights (F) to Back Stretcher (H). E Slide Back Panels (E) into position. F F Head Cap Bolt (long) Cross Dowel G H Cross Dowel Head Cap Bolt (long) STEP 4 Attach Back Stretcher (G) to unit with Cross Dowels and Head Cap Bolts (long). Figure 3 I K K J STEP 5 Attach Front Stretcher (J) to unit. Attach Front Uprights (K) to unit.
Assembly Instructions 4/8 Cam Lock STEP 6 Attach Side Panels (A) and (B) to unit with Cam Locks. B A Cam Lock Cross Dowel N Head Cap Bolt Head Cap Bolt (long) M STEP 7 Attach Base (M) to unit with Cross Dowels and Head Cap Bolts (long). N Attach Legs (N) to Base (M) with Head Cap Bolts. Cam Lock Screw U STEP 8 Arrow label Place Top (U) upside down on a soft cloth. Insert Cam Lock Screws into pre-drilled holes in Top (U), then tighten.
Assembly Instructions 5/8 Knob Machine Screw STEP 9 Turn unit to its’ upright position. Insert Adjustable Pins into side panels and middle panels at desired level. R Place Shelves (Q) into position. Attach Doors (R) and (S) to unit by sliding door hinges into side panel hinges. (See Figure 4) Q Q Attach Knobs to Doors (R) and (S) with Machine Screws. (See Figure 5) S Adjustable Pin Figure 4 Figure 5 U Cam Lock STEP 10 Attach Top (U) to unit with Cam Locks.
Assembly Instructions 6/8 Drawer (T) Wood Screw (long) Bottom T1 STEP 11 T3 Attach Drawer Front (T1) and Drawer Back (T2) to Drawer Side (T3) with Wood Screws (long). T2 T4 Attach Drawer Side (T4) to unit with Wood Screws (long). Roller at back Wood Screw (short) STEP 12 Slide Drawer Bottom (T5) into groove. T5 Attach Drawer Bottom (T5) to unit with Wood Screws (short). Machine Screw STEP 13 Attach Handle with Machine Screws. Handle Part List T1. Drawer Front 3 pcs. T2. Drawer Back 3 pcs.
Assembly Instructions 7/8 STEP 14 T Slide Drawers (T) into position. T T L P Slide Wine Grids (P) into grooves of Fixed Shelf (L). Slide Wine Grids (O) into unit. P O O Wood Screw for Back Panel STEP 15 Level unit by adjusting the adjustable levelers on bottom of unit. (See Figure 6) Insert Wood Screws for Back Panel into pre-drilled holes in unit, then tighten. Note: Unit must be level before tightening these screws.
Assembly Instructions 8/8 IMPORTANT To help reduce the risk of the unit tipping over, the Tip-over Restraint must be installed following these instructions exactly. STEP 16 Anchor in wall Place unit at desired location. Drill a 3/8” hole in wall in-line with Pre-drilled hole at top of unit. Bracket on wall Wall Screw Pre-drilled hole at top of unit Wood Screw 3/8” wall hole Move unit. Tie end Insert Anchor into the wall hole and attach Bracket with Wall Screw.
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.
20 05100 0302 Hutch IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Hutch Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List A. Top 1 pc. F. Back Stretcher 1 pc. B. Side Panel 1 pc. G. Back Stretcher 1 pc. C. Side Panel 1 pc. D. Back Panel 3 pcs. E. Back Upright 2 pcs. H. Front Stretcher 1 pc. I.
Assembly Instructions 2/6 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the screws until each part is properly assembled. Cam Lock Screw STEP 1 Insert Cam Lock Screws into pre-drilled holes in Top (A), Side Panels (B), (C) and Fixed Shelf (I), then tighten.
Assembly Instructions 3/6 STEP 3 Attach Fixed Shelf (I) to unit with Cam Locks. I Cam Lock Cam Lock H STEP 4 Attach Middle Panels (L) and (M) to unit with Cam Locks. L M Attach Front Stretcher (H) to unit with Cam Lock. Cam Lock Cam Lock STEP 5 C Attach Side Panel (C) to unit with Cam Locks.
Assembly Instructions 4/6 Adjustable Pin STEP 6 N Insert Adjustable Pins into side panels and middle panels at desired level. O K Place Shelves (J) and (K) into position. J K Attach Doors (N) and (O) to unit by sliding door hinges into side panel hinges. (See Figure 3) Attach Knobs to Doors (N) and (O) with Machine Screws. (See Figure 4) Machine Screw Figure 3 A Knob Figure 4 Cam Lock STEP 7 Attach Top (A) to unit with Cam Locks.
Assembly Instructions 5/6 STEP 8 Insert Wood Screws for Back Panel into pre-drilled holes in unit. Wood Screw for Back Panel Wood Screw for Bracket Figure 5 Bracket STEP 9 Attach Hutch to Buffet with Brackets by inserting Wood Screws for Bracket into pre-drilled holes.
Assembly Instructions 6/6 IMPORTANT To help reduce the risk of the unit tipping over, the Tip-over Restraint must be installed following these instructions exactly. STEP 10 Anchor in wall Place unit at desired location. Bracket on wall Pre-drilled hole at top of unit Wall Screw Wood Screw 3/8” wall hole Drill a 3/8” hole in wall in-line with pre-drilled hole at top of unit. Move unit. Insert Anchor into the wall hole and attach Bracket with Wall Screw.
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.
20 05100 0101 Solid Wood Top IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List U. Top 1 pc. For assembly see instructions in carton 20 05100 Buffet carton. Home Styles Customer Service: www.homestyles-furniture.com, servicedesk@homestyles-furniture.
