Use and Care Manual

ManualsBrandsHOMESTYLES ManualsFurnitureWhite Buffet with Hutch

Part List

5100 102-

Stainless Steel Top

IMPORTANT

Carefully remove all the parts from the carton and

place them individually on a soft cloth to prevent

scratches or other damage.

Carefully and strictly follow these assembly instructions

to ensure a completed product as designed.

Do not use power tools above 8 volts to assemble.

Care Instructions

This stainless steel top is made from high grade stainless steel on a strong wood

product base construction.

To avoid scratching the top during assembly, do not remove the top from this

carton until the body has been assembled and is ready for the top to be installed.

After removing the top from this carton place it on a soft cloth. ......................

This stainless steel top is ideal as a surface for food preparation but cannot be

used as a cutting or chopping board. Do not use knives or any sharp objects

directly on the top.

If scratched the following may improve the appearance of the top:

Apply talcum powder or flour on the scratched area and rub with very

fine steel wool in the same direction as the top’s hairline scratch pattern.

For assembly see instructions in 5100 Buffet carton.

styles Customer Service: www.homestylesfurniture.com,home

servicedesk@homestylesfurniture.com,

888-680-7460

Summary of content (17 pages)

PAGE 1
5100-102 Stainless Steel Top IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List Care Instructions This stainless steel top is made from high grade stainless steel on a strong wood product base construction.
PAGE 2
5100-002 Buffet IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List G. Back Rail 1 pc. H. Back Rail 1 pc. A. Side Panel 1 pc. B. C. Side Panel Middle Panel 1 pc. 1 pc. K. Front Upright 2 pcs. O. Wine Grid 2 pcs. L. Fixed Shelf 1 pc. P. Wine Grid 2 pcs. D.
PAGE 3
Assembly Instructions 2/8 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Hex Wrench as the bolts may need to be tightened in the future.
PAGE 4
Assembly Instructions 3/8 STEP 3 Attach Back Rail (H) to unit with Cross Dowels and Head Cap Bolts (long). (See Figure 3) E E E Attach Back Uprights (F) to Back Rail (H). Slide Back Panels (E) into position. F F Cross Dowel Head Cap Bolt (long) H Figure 3 G Head Cap Bolt (long) Cross Dowel STEP 4 Attach Back Rail (G) to unit with Cross Dowels and Head Cap Bolts (long). I K K J STEP 5 Attach Front Rail (J) to unit. Attach Front Uprights (K) to unit. Attach Front Rail (I) to unit.
PAGE 5
Assembly Instructions 4/8 Cam Lock STEP 6 B Attach Side Panels (A) and (B) to unit with Cam Locks. A Cross Dowel N STEP 7 Attach Base (M) to unit with Cross Dowels and Head Cap Bolts (long). M Attach Legs (N) to Base (M) with Head Cap Bolts. Head Cap Bolt Head Cap Bolt (long) N Cam Lock Screw Arrow label STEP 8 Place Top (U) upside down on a soft cloth. Insert Cam Lock Screws into pre-drilled holes in Top (U), then tighten.
PAGE 6
Assembly Instructions 5/8 STEP 9 Turn unit to its upright position. Insert Adjustable Pins into side panels and middle panels at desired level. R Place Shelves (Q) into position. Attach Doors (R) and (S) to unit by sliding door hinges into side panel hinges. (See Figure 4) S Q Q Attach Knobs to Doors (R) and (S) with Machine Screws. (See Figure 5) Adjustable Pin Figure 4 Knob Machine Screw Figure 5 U Cam Lock STEP 10 Attach Top (U) to unit with Cam Locks.
PAGE 7
Assembly Instructions 6/8 Drawer (T) Wood Screw (long) Bottom Botto T3 STEP 11 m Attach Drawer Front (T1) and Drawer Back (T2) to Drawer Side (T3) with Wood Screws (long). T1 T4 T2 STEP 12 Attach Drawer Side (T4) to unit with Wood Screws (long). Roller at back Wood Screw (short) Botto Slide Drawer Bottom (T5) into groove. m T5 Attach Drawer Bottom (T5) to unit with Wood Screws (short). STEP 13 Machine Screw Handle Attach Handle with Machine Screws. Part List T1. Drawer Front 3 pcs. T2.
PAGE 8
Assembly Instructions 7/8 T STEP 14 T T L P P Slide Drawers (T) into position. Slide Wine Grids (P) into grooves in Fixed Shelf (L). Slide Wine Grids (O) into unit. O O Wood Screw for Back Panel STEP 15 Level unit by adjusting the adjustable levelers on bottom of unit. (See Figure 6) Note: Unit must be level to proceed. Insert Wood Screws for Back Panel into pre-drilled holes in unit, then tighten. Note: Unit must be level before tightening these screws.
PAGE 9
Assembly Instructions 8/8 IMPORTANT To help reduce the risk of the unit tipping over, the Tipover Restraint must be installed following these instructions exactly. STEP 16 Anchor in wall Place unit at desired location. Bracket on wall Wall Screw Pre-drilled hole at top of unit Wood Screw 3/8” wall hole Drill a 3/8” hole in wall in-line with Pre-drilled hole at top of unit. Tie end Move unit. Lock end Bracket at top of unit Insert Anchor into the wall hole and attach Bracket with Wall Screw.
PAGE 10
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.
PAGE 11
5100-302 Hutch IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Hutch Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List A. Top 1 pc. B. Side Panel 1 pc. F. Back Rail 1 pc. G. Back Rail 1 pc. K. Shelf 2 pcs. J. Shelf 1 pc. L. Middle Panel 1 pc. C. Side Panel 1 pc. D. Back Panel 3 pcs. E.
PAGE 12
Assembly Instructions 2/6 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the screws until each part is properly assembled. Cam Lock Screw STEP 1 Insert Cam Lock Screws into pre-drilled holes in Top (A), Side Panels (B), (C) and Fixed Shelf (I), then tighten. (See Figure 1) A B C I Figure 2 Figure 1 Cam Lock G STEP 2 B D D E D E F Attach Back Rail (F) to Side Panel (B) with Cam Lock.
PAGE 13
Assembly Instructions 3/6 Cam Lock STEP 3 I Attach Fixed Shelf (I) to unit with Cam Locks. Cam Lock H L STEP 4 M Attach Middle Panels (L) and (M) to unit with Cam Locks. Attach Front Rail (H) to unit with Cam Lock. Cam Lock STEP 5 C Attach Side Panel (C) to unit with Cam Locks.
PAGE 14
Assembly Instructions 4/6 Adjustable Pin STEP 6 Insert Adjustable Pins into side panels and middle panels at desired level. N K Place Shelves (J) and (K) into position. J K O Attach Doors (N) and (O) to unit by sliding door hinges into side panel hinges. (See Figure 3) Attach Knobs to Doors (N) and (O) with Machine Screws. (See Figure 4) Knob Machine Screw Figure 3 Figure 4 Cam Lock A STEP 7 Attach Top (A) to unit with Cam Locks.
PAGE 15
Assembly Instructions 5/6 STEP 8 Insert Wood Screws for Back Panel into pre-drilled holes in unit. Wood Screw for Back Panel Figure 5 Wood Screw for Bracket Bracket STEP 9 Attach Hutch to Buffet with Brackets by inserting Wood Screws for Bracket into pre-drilled holes, then tighten.
PAGE 16
Assembly Instructions 6/6 IMPORTANT To help reduce the risk of the unit tipping over, the Tipover Restraint must be installed following these instructions exactly. STEP 10 Anchor in wall Place unit at desired location. Bracket on wall Wall Screw Pre-drilled hole at top of unit Wood Screw 3/8” wall hole Drill a 3/8” hole in wall in-line with Pre-drilled hole at top of unit. Tie end Move unit. Lock end Bracket at top of unit Insert Anchor into the wall hole and attach Bracket with Wall Screw.
PAGE 17
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.