Instructions / Assembly

ManualsBrandsHOMESTYLES ManualsOutdoor BenchesLaguna 47.5 in. Wood Outdoor Bench

Hardware List

Part List

Home Styles Customer Service: www.homestyles-furniture.com,

servicedesk@homestyles-furniture.com,

888-680-7460, 877-831-0319

Tool(s) required for assembly: Phillips screwdriver, Level

88 5134 26

Bench

IMPORTANT

Carefully remove all the parts from the carton and

place them individually on a soft cloth to prevent

scratches or other damage.

Carefully and strictly follow these assembly instructions

to ensure a completed product as designed.

Do not use power tools above 8 volts to assemble.

M8x32

Wood Screw

for Pull Handle

2 pcs. (+1 extra)

Pull Handle

2 pcs.

Top

1 pc.

Middle Panel

1 pc.

Front Stretcher

1 pc.

Back Panel

1 pc.

Base

1 pc.

Leg

1 pc.

Door

1 pc.

Door

1 pc.

Side Panel

1 pc.

Side Panel

1 pc.

M4x19

Wood Screw (short)

12 pcs. (+1 extra)

M8x38

Wood Screw (long)

1 pc. (+1 extra)

Small Hex Wrench

1 pc.

Magnet

2 pcs.

M3x15

Wood Screw

for Magnet

4 pcs. (+1 extra)

M6x35

Head Cap Bolt (short)

4 pcs. (+1 extra)

M6x40

Head Cap Bolt (long)

8 pcs. (+1 extra)

Hex Wrench

1 pc.

Summary of content (5 pages)

PAGE 1
88 5134 26 Bench IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List A. Top 1 pc. B. Side Panel 1 pc. E. Front Stretcher 1 pc. F. Back Panel 1 pc. H. Leg 1 pc. C. Side Panel 1 pc. D. Middle Panel 1 pc. G. Base 1 pc. I. Door 1 pc. J. Door 1 pc.
PAGE 2
Assembly Instructions 2/4 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Hex Wrench in a safe place as the bolts may need to be tightened up in the future. C STEP 1 Attach Back Panel (F) and Base (G) to Side Panel (B) with Head Cap Bolts (long).
PAGE 3
Assembly Instructions 3/4 Head Cap Bolt (short) A I J STEP 3 Attach Doors (I) and (J) to unit with Wood Screws (short). (See Figure 3) Attach Pull Handles to Doors (I) and (J) with Wood Screws for Pull Handle. (See Figure 4) Attach Top (A) to unit with Head Cap Bolts (short). Level unit by adjusting the adjustable levelers on the bottom of legs.
PAGE 4
Assembly Instructions 4/4 IMPORTANT If the magnetic door catches are too strong and difficult to open, the magnetic power can be reduced and the door made easier to open by doing the following: 1 2 Magnet Magnet location. 3 Magnet position. 4 Rotate the Magnet until one Screw is all the way forward and the other Screw is all the way back in the catch slots. Loosen the Screws only halfway. 5 6 Tighten the Screws. New position.
PAGE 5
CARE INSTRUCTIONS Advisory Notes · · · · · · · Do not use power tools above 8 volts to assemble. Periodic structural checks of this furniture should be undertaken. Do not use if there are any doubts about its’ fitness for purpose. Exercise care so as to not trap fingers in any of the hinged parts of this furniture. Always use on firm level ground, ensuring that all legs remain in contact with the ground. Do not stand on a chair or sit or stand on any other item.