Instructions / Assembly

ManualsBrandsHOMESTYLES ManualsDining Room Sets5-Piece Black and Oak Dining Set

Hardware List

Part List

Tool(s) required for assembly: Level

Home Styles Customer Service: www.homestyles-furniture.com,

servicedesk@homestyles-furniture.com,

888-680-7460, 877-831-0319

Carton 88 5168 301 is also needed for assembly.

IMPORTANT

Carefully remove all the parts from the carton and

place them individually on a soft cloth to prevent

scratches or other damage.

Carefully and strictly follow these assembly instructions

to ensure a completed product as designed.

Do not use power tools above 8 volts to assemble.

Connector Panel

1 pc.

Leg

4 pcs.

Table Top

1 pc.

Hex Wrench

1 pc.

Small Hex Wrench

1 pc.

M6x40

Head Cap Bolt

4 pcs. (+1 extra)

Nut

12 pcs. (+1 extra)

Key Wrench

1 pc.

Spring Washer (large)

12 pcs. (+1 extra)

Flat Washer (large)

12 pcs. (+1 extra)

Spring Washer (small)

4 pcs. (+1 extra)

Flat Washer (small)

4 pcs. (+1 extra)

88 5168 302

Round Table

Summary of content (7 pages)

PAGE 1
88 5168 302 Round Table IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List B. Connector Panel 1 pc. A. Table Top 1 pc. D. Leg 4 pcs. Hardware List Hex Wrench 1 pc. Key Wrench 1 pc. Small Hex Wrench 1 pc. Flat Washer (large) 12 pcs.
PAGE 2
Assembly Instructions 2/2 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Hex Wrench in a safe place as the bolts may need to be tightened up in the future.
PAGE 3
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.
PAGE 4
88 5168 301 Round Table IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List C. Post 1 pc. For assembly see instructions in carton 88 5168 302. Home Styles Customer Service: www.homestyles-furniture.com, servicedesk@homestyles-furniture.
PAGE 5
88 5168 80 Side Chair IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List A. Seat 1 pc. C. Leg 1 pc. B. Leg 1 pc. D. Back Frame 1 pc. Hardware List Flat Washer 11 pcs. (+1 extra) Hex Wrench 1 pc. M6x40 Head Cap Bolt (short) 3 pcs.
PAGE 6
Assembly Instructions 2/2 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. Keep Hex Wrench in a safe place as the bolts may need to be tightened up in the future. STEP 1 Attach Legs (B) and (C) to Seat (A) with Flat Washers, Spring Washers and Head Cap Bolts. (See Figure 1) B Tightening the bolts only half way.
PAGE 7
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.