20051700070 Vanity with Mirror . eg IMPORTANT Cara fully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List 8. ¢. Mirror Base Ul stent Leg Mirror 1pe. Hl 2 pes. 4 pes. Support Back Anal Je i Divider Divider Tpe 1 pe. G. Front Rail Side Pans! 2 pes. 1pe. L H.
( Assembly Instructions 2/11 ) IMPORTANT = Use a soft cloth between these parts and the floor. = Da not use power tools above 8 volts to assemble. + Do not tighten zl the screws until hats part is properly assembled. o The unit must be level to work properly. Use the included adjustable levelers to level. © Keep Key Wrench in a safe place as the Bolts may need to be tightened up in the future.
( Assembly Instructions 3/11 ) STEP 3 Cam Lock: Attach Front Rail {K) and TN Back Pane! (N} to unit with & Cam Locks. ) {See Figure 2} STEP 4 Attach Side Panels {G) and {H} to unit with Cam Lacks. {See Figure 2} 4.
( Assembly Instructions 5/11 ) STEP 7 Attach Mirror Supports (B} and (C} to Mirror Base (D) with 1" Round Head Screws. STEP 8 Attach Mirror {A} to unit using Axis Bolts, Mirror Axes and Plastic Washers. {See Figure 3} Axis Bolt A Plastic Washer 4.
( Assembly Instructions 6/11 ) STEP 9 Attach Battens (E) to unit from Step 6 and unit from Step 8 with Bolts, Spring Washers and Flat Washers, Tighten Bolts using Key Wrench. (See Figure 4) Flat Washer yr 8 Wash @. o rusher Pah (X a (A STEP 10 Level unit by adjusting the adjustable levelers on bottom of legs. {See Figure 5) Figure 5 4.
( Assembly Instructions 7/11 ) IMPORTANT = Ta hap reduce the risk of the unit tipping over, the Tip-over Restraint must be installed following these instructions exactly. STEP 11 Place the unit at desired location. Mark wall with pencil to show position of hole in Back Pane! (N). (See Figure 6} Move unit. Drill a 3/8" hole in wall 1” below mark. Insert Anchor into the wall hole and attach Tip-over Restraint to Anchor with 1 1/2” Round Head Screw and Flat Washer.
( Assembly Instructions 8/11 ) Drawer (P) STEP 12 Attach Drawer Side (P3) to Drawer Front {P1} and Drawer Back (P2)} with 1 1/4" Flat Head Screws. 11/4" Fiat Hood Screw 1/8" Fist Hoa Craw STEP 13 Rolls st back ha Insert Drawer Bottom (P5} into the groove. Se Attach Drawer Side {P4} to unit with 1 1/4" Flat Head Screws. STEP 14 Attach Handle with Machine Screws. + Machine Screw STEP 15 Nn Place Jewel Box (P6) into position.
( Assembly Instructions 9/11 ) Drawer (Q) STEP 16 Attach Support {Q6) to Drawer Front (Q1) and Drawer Back (02). a . CC 11/4" Fat Head Sower panache Drawer Side (G3) to Drawer Front (Q1} and Drawer Back {Q2) with 1 1/4" Flat Head Rioter at back Screws. STEP 17 41/4" Fiat Head Sere Insert Drawer Bottom {Q5) into the groove. a Attach Drawer Side {Q4) to unit with 1 1/4" Flat Head Screws. pee Machine Screw STEP 18 Attach Handles with Machine Screws.
( Assembly Instructions 10/11 ) STEP 19 For Drawer (PF) uninstall the lower center screw and loosen slight the upper center screw. For Drawer {Q) loosen slightly the two screws per-installed on back of drawer front. STEP 20 Insert drawers into unit, then adjust drawer front panels left or right and up or down until drawer gaps look proportional. STEP 21 Pull each drawer open slowly and re-tighten screws from Step 19.