2005170 0431 LT Dresser IMPORTANT Carefully remove all the parts from the carton and place therm individually on a soft cloth to prevent scratches or other damage. Carefully and strictly fol ow these assembly instructions to ensure a completed product as designed. De not use power tools above 8 volts to assemble. ~ Part List A, Top 1pe Foot Canter Lag 4 pes. 1pe. had. MBE. . Drawer Back Drawer Side Drawer ee Drawer Bottom Front Rail 2 pes. 2 pes. 2 pes. 2 pes. Front Rai . : Drawer Front Drawer iv 4 pes. Na.
( Assembly Instructions 2/11 ) IMPORTANT » Use a soft cloth between these parts and the floor. + Do not use power tools above 8 volts to assemble. » Do not tighten all the screws unt] each part 's properly assembled, Tha unit must be level to work properly. Use the included adjustable levelers to level. STEP 1 insert Cam Lock Screws into per-drilled holes of Top (A), Side Panels (B), (C}, Front Rails (7) (G), Base (hand | Back Panel (L}, then tighten. ; a.
( Assembly Instructions 3/11 ) STEP 2 coma Assemble Back Panels (K) and {L) with = ® Cam Locks. (See Figure 1) : Note: Arrow label indicates top of Back Panel (i). Figure 1 STEP 3 Attach Front Rails (E), (F) and (G) to Divider {ID} with Cam Locks and 11/2" Round Head Screw. an.
( Assembly Instructions 4/11 ) a 144° Round Head Screws Attach unit from Step 2 to unit from Step 3 with 1 1/4" Round Head Screws. STEP STEPS Attach Side Panel (B) to unit with Cam Locks. a.
( Assembly Instructions 5/11 ) STEP 6 Attach Side Panel {C) to unit with Cam Locks. Tle Cam Lok STEP Attach Base (H) to unit with Wooden Dowels, Cam Locks and 1 1/2" Round Head Screws. a.
( Assembly Instructions 6/11 ) STEP 8 Attach Feet and Center Leg {J) to unit. STEP 9 Attach Top {A} to unit with Cam Locks and 1 1/4" Round Head Screws. Note: A Phillips screwdriver 5° or less in length is recommended. Lee! unit by adjusting the adjustable levelers on bottom of unit. {See Figure 2) Note: Unit must be level to work properly. 1 1/4" Round Head Screw \ Figure 2 a.
( IMPORTANT Assembly Instructions 7/11 » Tar help reduce the risk of the unit tipping aver, the Tip-over Restraint must be installed following these instructions exactly. STEP 10 Place unit at desired location. Mark wall with pencil just above and in-line with hole in Top (A). (See Figure 3) Move unit. Drill a 3/8" hole in wall 1 1/2* below mark. Insert Anchor into the wall hole and attach Restraint to Anchor with 1 1/2” Round Head Screw and Flat Washer.
( Assembly Instructions 8/11 ) Drawer (M) STEP 11 Attach Drawer Sides (M3), (M4) and Drawer Supports {(Mé) to Drawer Back (M2) with 11/4" Flat Head Screws. Rotter at back STEP 12 11/4" Flat Head Screw Insert Drawer Boston (M5) into the groove. Attach Drawer Front (M1) to unit with 11/4" Flat Head Screws. Machine Screw STEP 13 Attach Handles with Machine Screws. Note: Drawer assembly is not complete until 3/4” Flat Head Screws are used in a later step.
( Assembly Instructions 9/11 ) Drawer (N) STEP 14 Attach Drawer Sides (N3), (N4) and Drawer Supports (Mé) to Drawer Back (N2) with 11/4" Flat Head Screws. Roller at back “mye 1 1/4" Fiat Head Screw STEP 1 5 1144" Flat Head Screw Insert Drawer Boston (N5) into the groove. Attach Drawer Front (N1) to unit with 11/4" Flat Head Screws. Machine Screw STEP 16 Attach Handles with Machine Screws. Note: Drawer assembly is not complete until 3/4” Flat Head Screws are used in a later step. Drawer Back 4 pes.
( Assembly Instructions 10/11 ) STEP 17 Loosen slightly the screws per-installed on back of drawer fronts. p—— oe) STEP 18 a) ks = Insert drawers into unt, then — [I adjust drawer front panels left right and up or down until drawer gaps look proportional, a > > STEP 19 Pull gate drawer open slowly and re-tighten screws from Step 17. Make sure drawer front panel does not move and lock drawer front panel into position with 3/4" Flat Head Screws.