Assembly Instructions 2

ManualsBrandsHomestyles ManualsDining Room & KitchenHomestyles Cambridge Kitchen Island With Quartz Top

Hardware List

Part List

Home Styles Customer Service: www.homestyles-furniture.com,

servicedesk@homestyles-furniture.com,

888-680-7460, 877-831-0319

Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit

IMPORTANT

Cartons 88 5523 94Q1 or 941 and 942 are also needed for assembly.

88 5170 943

Kitchen Island

M4x25

Machine Screw

6 pcs.

Cam Lock Screw

18 pcs.(+2 extra)

Spring Washer

6 pcs. (+1 extra)

Adjustable Pin

16 pcs. (+1 extra)

Knob

6 pcs.

M3x15

Wood Screw

for back panel

8 pcs. (+1 extra)

Magnet

2 pcs.

M x388

Head Cap Bolt

6 pcs. (+1 extra)

Carefully remove all the parts from the carton and

place them individually on a soft cloth to prevent

scratches or other damage.

Carefully and strictly follow these assembly instructions

to ensure a completed product as designed.

Do not use power tools above 8 volts to assemble.

Drawer

2 pcs.

Refer to later page(s) of these

instructions for drawer assembly.

Shelf

4 pcs.

Door

1 pc.

Back Upright

1 pc.

Front Rail

2 pcs.

Door

1 pc.

Base

1 pc.

Back Rail

2 pcs.

Back Panel

2 pcs.

Cam Lock

18 pcs.(+6 extra)

Small

Hex Wrench

1 pc.

Wood Dowel

6 pcs.

Flat Washer

6 pcs. (+1 extra)

Hex Wrench

1 pc.

M3x15

Wood Screw

4 pcs. (+1 extra)

Summary of content (6 pages)

PAGE 1
88 5170 943 Kitchen Island IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List E. Base 1 pc. F. Shelf 4 pcs. H. Back Upright 1 pc. G. Front Rail 2 pcs. J. Door 1 pc. K. Door 1 pc. I. Back Panel 2 pcs. M. Drawer 2 pcs. L. Back Rail 2 pcs.
PAGE 2
Assembly Instructions 2/5 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the screws until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Hex Wrench in a safe place as the bolts may need to be tightened up in the future.
PAGE 3
Assembly Instructions 3/5 STEP 2 Attach Back Rails (L) to Side Panel (C) with Cam Locks. (See Figure 2) I Slide Back Panel (I), Back Upright (H) and Back Panel (I) to unit. H L I Cam Lock L C Figure 2 Figure 3 Cam Lock STEP 3 D Attach Front Rails (G) and Middle Panel (D) to unit with Cam Locks. B Attach Side Panel (B) to unit with Cam Locks.
PAGE 4
Assembly Instructions 4/5 Drawer (M) STEP 5 M4 Attach Drawer Sides (M3) and (M4) to Drawer Back (M2), then flip the locks. (See Figures 4 and 5) M2 M3 Lock Roller at back STEP 6 Figure 4 Figure 5 Slide Drawer Bottom (M5) into the grooves in Drawer Sides (M3) and (M4). Push Drawer Bottom (M5) all the way into Drawer Back (M2). M1 M4 M5 M3 M2 Attach Drawer Front (M1) to unit, then flip the locks. STEP 7 Attach Knob with Machine Screw. Part List M1. Drawer Front 2 pcs. M2. Drawer Back 2 pcs.
PAGE 5
Assembly Instructions 5/5 Wood Screw for back panel Cam Lock STEP 8 A Wood Dowel Turn the unit to its’ upright position, then insert Wood Dowels into side panels and middle panel. Attach Top (A) to unit with Cam Locks. Attach Magnets to unit with Wood Screws. (See Figure 6) Level unit by adjusting the adjustable levelers on the bottom of unit. (See Figure 7) Insert Wood Screws for back panel into pre-drilled holes of unit. Note: Unit must be level before tightening these screws.
PAGE 6
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.