20051850016 Student Desk Sa IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft doth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List F. Front Rail 1 pe. B. Side Frame 1 pe. E. Frame 1pe, C. Side Frame 1 pe. oO. Divider 1 pe Refer to later page(s) of these instructions for drawer assembly. A.
( Assembly Instructions 2/8 ) IMPORTANT » Use a soft cloth between these parts and the floor. ® Do not use power too's above 8 volts to assemble. » Do not tighten all the screws unt ach part is properly assembled, ® The unit must be level to work properly. Lie the included adjustable levelers to level. ® Keep Hex Wrench as the bolts may need to be tightened in the future.
( Assembly Instructions 3/8 ) STEP 3 Attach Front Rail (F} to unit with Cam Lock. Attach Frame (E} to unt with Dowels and 1 1/4" Round Head Screws. Fiat Washer Siring Washer Head Cap Bolt % 11/4" Round Head Screw b#® Hex Wrench gs Figure 2 STEP 4 Attach Side Frame (B) to unit with Cam Locks, Flat Washers, Spring Washers and Head Cap Bolts (short), Attach Stretcher {G) to unit with Dowel, Flat Washer, Spring Washer and Head Cap Bolt {long}. Tighten Head Cap Bolts with Hex Wrench. {See Figure 2) 0.
( Assembly Instructions 4/8 ) STEP 5 Attach Side Frame (C) to unit with Dowel, Cam Locks, Flat Washers, Spring Washers, Head Cap Bolts {long and short). Tighten Head Cap Bolts with Hex Wrench. Head Cap Holt (short) Spring Washer Flat Washer Car Les eke Head Cap Bot long) Spring Washboard— pa. _ Fiat Washer BR Figure 3 STEP 6 Tum unit to its upright position. Level unit by adjusting the adjustable levelers on bottom of legs. (See Figure 3} 0.
( Assembly Instructions 5/8 ) Drawer (I) ~~ ~ Attach Drawer Front {11}, and Drawer Back (12) to Heller at back ~ 11/4" Flat Head Sam Drawer Side (13) with 1 1/4" Flat Head Screws. STEP 8 11/4" Fiat Hon Screw pl Insert Drawer Bottom (5) into groove. RS Attach Drawer Side (14) to unit with ~~ 11/4" Flat Head Screws. STEP 9 Attach Handle with Machine Screws. Note: Drawer assembly is not complete until 3/4” Flat Head Screws are used in a later step.
( Assembly Instructions 6/8 ) Drawer (J) STEP 10 Attach Drawer Front {J1), and Drawer Back (12) to Roller at back 2 . Drawer Side {13) with 1 1/4" Flat Head Screws. STEP 11 11/4" Fiat Hind Screw pl N Insert Drawer Bottom (5) into groove. Attach Drawer Side {4) to unit with 11/4" Flat Head Screws. STEP 12 Attach Handle with Machine Screws. Note: Drawer assembly is not complete until 3/4” Flat Head Screws are used in a later step. Part List Drover Front Drover Back Drawer Si de Drawer Side Drawer Bottom 1 pe.
( Assembly Instructions 7/8 ) STEP 13 Loosen slightly screws per-installed on back of drawer fronts. STEP 14 Insert drawers into unit, then adjust drawer front panels left or right and up or down until drawer gaps look proportional. STEP 15 Pull each drawer open slowly, then re-tighten screws from Step 13. Make sure drawer front panels do not move and lock drawer front panels into position with 3/4" Flat Head Screws. Note: These 3/4" Flat Head Screws must be installed to complete the drawer assembly.
CARE INSTRUCTIONS NEVER NEVER allow lipids to remain on armature. {ise glass Cleaners on Absorption causes parts to warp finished furniture: Ammonia and. split and finishes to laminate. chemically attacks the finish, = Diana place direct sunlight. PREVENT FADING Da anti directly on surface.