2005185 0181 e Pedestal Desk IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft doth to prevent scratches or other damage. Carefully and strictly fol'ow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List k. Front Rail 1 pe. L Front Rail 1pe. Drawer Back _j\ Front Rail 1 pe. K,\ Front Rail 1pe 51, T Drawer Front Drawer Front 1pe. Back Panel 1pe.
0051850182 Pedestal Desk e IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft doth to prevent scratches or other damage. Carefully and strictly fol'ow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. e i o, Part List Middle Panel 1pe. 8. pe Sde Anal 1pe. c. Side Pane 1pe. E. Riddle Pansy 1pe. A 53, 54, Drawer Side Drawer Side 2 pes. 2 pes. ©3. o4, Drawer Side Di rawer Side Nz 2 pes. 2 pes.
( Assembly Instructions 2/16 ) IMPORTANT » Lse & soft cloth between these parts and the floor. ® Do into use power too's above 8 volts to assemble. » Do not tighten all the screws unto sate part is properly assembled, ® The unit must be level to work properly. Lie the included adjustable levelers to level. STEP 1 Insert Can Lock Screws into per-drilled ‘ holes in Top (A}, Side Panels (B), (C), ’ ; Middle Panels (D), (E), Front Rails (F), | \ {G), (J), (K} and Back Panel {1}, ; then tighten.
( Assembly Instructions 3/16 ) STEP 2 Attach Front Rail (J] to Bottom (M) with Cam Locks. {See Figure 1) Attach Front Rail (K] to Bottom (M) with Cam Locks. Cam Lade STEP 3 Attach Bottom (M) with Front All {J) attached to Middle Panel {0} with Dowels and Cam Locks. Attach Bottom (M) with Front Rail (K} attached to Middle Pane! (E) with Dowels and Cam Locks.
( Assembly Instructions 4/16 ) STEP 4 Attach units to Back Panel {1 with Cam Locks. STEP 5 Attach Front Rails {F} and {G) to unt with Can Locks.
( Assembly Instructions 5/16 ) Swearer belle pointing to Front STEP 6 Orientate Front Rail {H) with Arrow label pointing to front of unit, then attach Front Ral {H} to unit with Cam Locks. STEP Orientate Front Rail () with Arrow label painting to front of unit, then attach Front Rail {l) to unit with Cam Locks. Attach Side Pane! {C) to unit with Cam Locks.
( Assembly Instructions 6/16 ) STEP 8 Turn unit to its upright position. Attach Top {A) to unit with Cam Locks and 1 174" Round Head Screws. Level unit by adjusting the adjustable levelers on bottom of unit. (See Figure 2) Note: Unit must be level to work properly.
( Assembly Instructions 7/16 ) Drawer (N} STEP 9 Attach Hand es to Drawer Front (N1} with Machine Screws, STEP 10 Attach Drawer Front (N1) to Drawer (N2} with 1/2" Flat Head Screws.
( Assembly Instructions 8/16 ) Drawer (O} = STEP 11 ~ S Attach Drawer Side (03) to Drawer Front ((01) and Drawer Back (02) Rifler at back Y1 14" Fist Head Sere with 1 1/4" Flat Head Screws. STEP Insert Drawer Bottom (O5) into groove. Attach Drawer Side (04} to unit with 1 1/4" Flat Head Screws. Machine Sower STEP 13 Attach Handle with Machine Screws, Note: Drawer assembly is not complete until 3/4” Flat Head Screws are installed n a later step.
( Assembly Instructions 9/16 ) S STEP 14 Attach Drawer Side (03) to Drawer Front (P1) and Drawer Back (O2) Y1 14" Fist Head Sere with 1 174" Flat Head Screws. Roller at back. STEP 1 5 114" Flt Head Sower L o Insert Drawer Bottom (O5) into groove. Attach Drawer Side (04} to unit with 1 1/4" Flat Head Screws. Machine Sower STEP 16 Attach Handle with Machine Screws, Note: Drawer assembly is not complete until 3/4” Flat Head Screws are installed n a later step.
( Assembly Instructions 10/16 ) Drawer (Q) STEP 17 Attach Drawer Side (03) to Drawer Front (Q1) and Drawer Back (Q2) with 1 1/4" Flat Head Screws. STEP 18 11/4" Flat Head Strew > Insert Drawer Bottom (O5) into groove. Attach Drawer Side (Q4) to unit with 1 1/4" Flat Head Screws. Machine Crow STEP 19 Attach Handle with Machine Screws. Note: Drawer assembly is not complete until 3/4” Flat Head Screws are installed 'n a later step. Part List Drawer Front Drawer Back Drawer side Drawer Side Drawer Bottom 1pe.
( Assembly Instructions 11/16 ) Drawer (R) STEP 20 Attach Drawer Side (03) to Drawer Front (R1) and Drawer Back (Q2) with 1 1/4" Flat Head Screws. Roller at back S 1 124" Flat Heine Screw STEP 21 11/4" Flat Head Strew > Insert Drawer Bottom (O5) into groove. Attach Drawer Side [Q4) to unit with 1 1/4" Flat Head Screws. Machine Crow STEP 22 Attach Handle with Machine Screws. Note: Drawer assembly is not complete until 3/4” Flat Head Screws are installed 'n a later step.
( Assembly Instructions 12/16 ) Drawer (5} T STEP 23 Attach Drawer Side (53) to Drawer Front (51} and Drawer Back {52) with 1 1/4" Flat Head Screws. TS 114" Fiat Head Sower STEP 24 144" Insert Drawer Bottom (O3] into groove. Attach Drawer Side (54) to unit with 1 1/4" Flat Head Screws. w Aching Sower STEP 25 Attach Handle with Machine Screws. Hand's Note: Drawer assembly is not complete until 3/4” Flat Head Screws are installed n a later step.
( Assembly Instructions 13/16 ) Drawer (T) T STEP 26 Attach Drawer Side (53) to Drawer Front {T1} and Drawer Back (52) with 1 1/4" Flat Head Screws. TS 114" Fiat Head Sower STEP 27 1 1/8" Flat Head Sower Insert Drawer Bottom (O3] into groove. Attach Drawer Side (54) to unit with 1 1/4" Flat Head Screws. w Aching Sower STEP 28 Attach Handle with Machine Screws. Hand's Note: Drawer assembly is not complete until 3/4” Flat Head Screws are installed 'n a later step.
( Assembly Instructions 14/16 ) STEP 29 Loosen slightly screws per-installed on back of drawer fronts of Drawers (O}, (P}, (Q), (R), {5} and (T). STEP 30 Slide Drawers {O), (P}, {O) and (R} into unit, Align metal runners on sides of Drawers (S) and (T} into metal guides on unit and slide Drawers (S) and (T} into unit. Adjust drawer front panels left or right and up or down unto! gaps look proportional.
Assembly Instructions 15/16 ) STEP 31 Pull Drawers (O), (P}, (Q} and (R} open slowly. Remove Drawers () and {T) by pushing plastic lever on left side up, pushing plastic lever on right side down and pull open. {See Figures 3 and 4) Figure 4 Re-tighten screws from Step 29. Make sure drawer front panels do not move and lock drawer front panels into position with 3/4" Flat Head Screws. Note: These 3/4" Flat Head Screws must be installed to complete the drawer assembly.
( Assembly Instructions 16/16 ) STEP 32 Place Metal Strips into position in Drawers {S) and (T). Metal Strips can be adjusted for letter or legal files. (See Figure 5) Slide Drawers (N}, {O), (P}, (Q), {R), (8} and (T} into position.
