20 05185 0041 Chest IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. ( . \ Part List A Top 1 pe. E. Front Rail 1pe. J. Drawer 1 pc. G. Back Panel Side Panel oS Jedi Panel Drawer Back Panel 1pe. Drawer = I. spec. Bottom Refer to later page(s) of these 1pc.
( Assembly Instructions 2/10 ) IMPORTANT « Use a soft cloth between these parts and the floor. « Do not use power tools above 8 volts to assemble. = Do not tighten all the screws until each part is properly assembled. « The unit must be level to work properly. Use the included adjustable levelers to level. Insert Cam Lock Screws into per-drilled holes in Top (A), Side Panels {B}, (C} and Back Panels (G), (H), then tighten. Cam Lock STEP 2 Attach Back Panel (G) to Back Panel {H} with Cam Locks.
( Assembly Instructions 3/10 ) STEP 3 Attach Bottom (I) to unit with Cam Locks. Cam er Dowel STEP 4 Orientate Front Rails (E) and (F) with Arrow label pointing to front of unit, then attach unit and Front Rails (D), (E), {F} to Side Panels (B) and {C) with Dowels and Cam Locks. can.
Assembly Instructions 4/10 Attach Top (A) to unit with Cam Locks and 1" Round Head Screws. STEP 5 STEP Turn u sting the adjustable levelers on bottom of Level unit by adj: 2 unit.
( IMPORTANT Assembly Instructions 5/10 « To help reduce the risk of the unit tipping over, the Tip over Restraint must be installed following these instructions exactly. STEP 7 Place unit at desired location. Mark wall with pencil just above and in-line with hole in Top (A). (See Figure 3) Move unit. Drill a 3/8" hole in wall 2” below mark. Insert Anchor into the wall hole and attach Tip over Restraint to Anchor with 1 1/2" Round Head Screw and Flat Washer.
( Assembly Instructions 6/10 ) Drawer STEP 8 Attach Drawer Sides (J3), (J4) and Supports {J6) to Drawer Back (J2) . with 1 1/4" Flat Head Screws. N41 1/4" Fiat Head Crow STEP 9 11/4" Fit Head Screw Insert Drawer Bottom (J5) into ed Screw ay groove. Attach Drawer Front {J1) to unit with 1 1/4" Flat Head Screws. STEP 10 Attach Handle with Machine Screws. Note: Drawer assembly is not complete until 3/4” Flat Head Screws are used in a later step.
( Assembly Instructions 7/10 ) Drawer STEP 11 Attach Drawer Sides (J3), (J4) and Supports {J6) to Drawer Back (J2) . with 1 1/4" Flat Head Screws. N41 1/4" Fiat Head Crow STEP 12 11/4" Fiat Head Screw —— Insert Drawer Bottom (K5) into ead Screw ag groove. Attach Drawer Front {K1) to unit with 1 1/4" Flat Head Screws. STEP 13 Attach Handle with Machine Screws. Note: Drawer assembly is not complete until 3/4” Flat Head Screws are used in a later step.
( Assembly Instructions 8/10 ) Drawer STEP 14 Attach Drawer Sides (J3), (J4) and Supports {J6) to Drawer Back (J2) . with 1 1/4" Flat Head Screws. N41 1/4" Fiat Head Crow STEP 15 11/4" Fiat Head Screw Insert Drawer Bottom (K5) into meathead Screw Se groove. Attach Drawer Front {L1) to unit with 1 1/4" Flat Head Screws. STEP 16 Attach Handle with Machine Screws. Note: Drawer assembly is not complete until 3/4” Flat Head Screws are used in a later step.
( Assembly Instructions 9/10 ) STEP 17 Loosen slightly screws per-installed on back of drawer fronts. Je. STEP 18 o Insert drawers into unit, then adjust drawer front panels left or right and up or down until drawer gaps look proportional. STEP 19 Pull each drawer open slowly, then re-tighten screws from Step 17. Make sure drawer front panels do not move and lock drawer front panels into position with 3/4" Flat Head Screws. Note: These 3/4" Flat Head Screws must be installed to complete the drawer assembly.
CARE INSTRUCTIONS NEVER NEVER allow liquids 1 remain on furniture, us glass cleaners on Absorption causes parts to warp finished furniture, Ammonia and split and finishes to laminate. chemically attacks the finish. Do not write directly on surface. PREVENT MARKING Do not use power tools above 8 volts to assemble. PREVENT CRACKING 1 Do not page hot objects on surface.
