20 051850070 Vanity with Mirror e IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft doth to prevent scratches or other damage. Carefully and strictly fol'ow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List Mirror Mirror Support Supper 1pe. 1pe. M. Stretcher Mirror 1pe. F. Top 1 pe. G, Side Anal Rent Rail 1pe. o. H. Side Panel 1pe peL P.
( Assembly Instructions 2/13 ) IMPORTANT » Lse & soft cloth between these parts and the floor. ® Do into use power too's above 8 volts to assemble. » Do not tighten all the screws unto sate part is properly assembled, ® The unit must be level to work properly. Lie the included adjustable levelers to level.
( Assembly Instructions 3/13 ) STEP 3 Attach Front Rail (K), and Back Pane! (N} to unit with Cam Locks. STEP 4 Attach Bottoms (O} and (P} to unit with Dowels and Cam Locks.
( Assembly Instructions 4/13 ) STEP 5 Attach Side Panel (G} to unit with Dowels and Can Locks, Fiat Washer Spring Washer Attach Stretcher (M) to Side Panel (G} with Flat Washer, Head Cap Bolt {ong) Spring Washer and Head Cap Bolt (long). Tighten Head Cap Bolt {long) with Hex Wrench. {See Figure 2) Hex Wrench * STEP 6 Attach Side Pane/ (H) to unit with Dowels, Cam Locks, Flat Washer, Spring Washer and Head Cap Bolt (long).
( Assembly Instructions 5/13 ) STEP Turk unit to its upright position. Attach Top {F} to unit with Dowels, Cam Locks and 1 1/4" Round Head Screws.
( Assembly Instructions 6/13 ) STEP 8 Attach Mirror Supports (B} and (C) to Miro Base (D) with 1 1/4" Round Head Screws. 114" Round Head Scow\ STET 9 Attach Mirror (A} to unit using Axis Bolts, Mirror Axes and Plastic Washers.
( Assembly Instructions 7/13 ) Flat Washer @ Spring Washer = Cap Bot [short) Hex Ranch —— Figure 4 Head Cap Bolt (hart) Spring Washer Flat Washer STEP 10 Attach Battens (E) to unit from Step 6 and unit from Step 7 with Head Cap Bolts (short), Spring Washers and Flat Washers, Tighten Head Cap Bolts (short) with Hex Wrench. (See Figure 4) Level unit by adjusting the adjustable levelers on bottom of legs.
( Assembly Instructions 8/13 ) IMPORTANT » Tor help reduce the rig of the unit tipping aver, the Tip over Restraint must be installed following these Instructions exactly. STEP 11 Place the unit at desired location. Mark wall with pencil to show position of hole in Back Pane! (N). (See Figure 6} Move unit, Drill a 3/8" hole in wall 17 below mark. Insert Anchor into the wall hole and attach Tip over Restraint to Anchor with 1 1/2" Round Head Screw and Flat Washer.
( Assembly Instructions 9/13 ) Drawer (Q) STEP 12 Attach Drawer Side (Q3) to Drawer Front (Q1) and Drawer Back (22) with 1 1/4" Flat Head Screws. 11/4" Flat Head Screwworm\ STEP 13 Insert Drawer Bottom (Q5) into groove, Attach Drawer Side {O4) to unit with 1 1/4" Flat Head Screws. STEP 14 Attach Handle with Machine Screws. STEP 15 Place Jewelry Tray (Q6) into position. Note: Drawer assembly is not complete until 3/4” Flat Head Screws are used in a later step.
( Assembly Instructions 10/13 ) iy Attach Drawer Side {Q3) to Drawer Front (R1) \ and Drawer Back {(02) with 1 1/4" Flat Head Screws. o 1174 eyt 1 1/4" Flat Head Screw T~ STEP 17 ~ Insert Drawer Bottom (Q5) into groove, . Attach Drawer Side {O4) to unit with 1 1/4" Flat Head Screws. STEP 18 Attach Handle with Machine Screws. STEP 19 Place Jewelry Tray (Q6) into position. Note: Drawer assembly is not complete until 3/4” Flat Head Screws are used in a later step.
( Assembly Instructions 11/13 ) Drawer (5} STEP 20 Attach Supper {56} to Drawer Front (51} and Drawer Back {52). T Voltmeter 1/4" Flat Head Strew Attach Drawer Side {83) to Drawer Front (S1) and Drawer Back (52) with 1 1/4" Flat Head Screws. STEP 21 11/4" Flat Head Screw B A, Insert Drawer Bottom (85) into groove. 2 Attach Drawer Side {54} to unit with 1 1/4" Flat Head Screws. STEP 22 Attach Handles with Machine Screws.
( Assembly Instructions 12/13 ) STEP 23 For Drawers (O} and (R} uninstall upper center screw and loosen slightly lower center screw. For Drawer (S} loosen slightly screws per-installed on back of drawer front. / STEP 24 Insert drawers into unit, then adjust drawer front panels left or right and up or down until drawer gaps look proportional.