20 05185 0432 home styles’ Dresser IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List Middle Panel =~ Drawer Bottom B. C. 2 pes. Side Panel spec. 05, Drawer Bottom 4 pes. Drawer Side Drawer Side lI Center Leg Support 4 pcs. 4 pcs. 1pc. 6 pcs.
( Assembly Instructions 2/15 ) IMPORTANT « Use a soft cloth between these parts and the floor. « Do not use power tools above 8 volts to assemble. = Do not tighten all the screws until each part is properly assembled. « The unit must be elev! to work properly. Use the included adjustable levelers to level. Cam Lock Crow— § STEP 1 Insert Cam Lock Screws into per-drilled holes in Top (A), Side Panels (B}, (C}, Front rails {G), (H), {l} and Back Panels (J), (K), then tighten.
( Assembly Instructions 3/15 ) STEP 2 Attach Back Panel (J} to Back Panel (K} with Cam Locks. (See Figure 1} Attach Middle Rail (E) to Middle Panel (D} with Dowels and 1 1/2" Round Head Screws. Attach Center Leg (L) to unit, then tighten. STEP 4 Attach unit from Step 3 to unit from Step 2 with Cam Locks.
( Assembly Instructions 4/15 ) STEP 5 Attach Front Rails (G}, (H) and () to unit with Cam Locks. Attach Front Rail (F) to unit with 1 1/2" Round Head Screw. Attach 1 1/2" Round Head Screw to unit.
Assembly Instructions 5/15 nit to Side Panels (B) and (C) STEP 7 Attach u STEP 8 nit with Cam Locks and 1" Round Head Screws.
( Assembly Instructions 7/15 ) IMPORTANT « To help reduce the risk of the unit tipping over, the Tip over Restraint must be installed following these instructions exactly. STEP 10 Place unit at desired location. Mark wall with pencil just above and in-line with hole in Top (A). {See Figure 3) Move unit. o Drill a 3/8” hole in wall 2” below mark. Insert Anchor into the wall hole and attach Tip over Restraint to Anchor with 1 1/2” Round Head Screw and Flat Washer.
( Assembly Instructions 8/15 ) Drawer STEP 11 Attach Drawer Sides (M3), {M4) and Supports (Mé) to Drawer Back (M2} TN 1 /4" Flat Head Se row with 1 1/4" Flat Head Screws. STEP 12 Insert Drawer Bottom (M5} into groove. Attach Drawer Front {(M1) to unit with 1 1/4" Flat Head Screws. STEP 13 Attach Handle with Machine Screws. \ Handle Note: Drawer assembly is not complete until 3/4” Flat Head Screws are used in a later step. Part List MS.
( Assembly Instructions 9/15 ) Drawer STEP 14 Attach Drawer Sides (M3), {M4) and Supports (Mé) to Drawer Back (M2) TN 1 /4" Flat Head Se row with 1 1/4" Flat Head Screws. STEP 15 Insert Drawer Bottom (M5} into groove. Attach Drawer Front (N1} to unit with 1 1/4" Flat Head Screws. STEP 16 Attach Handle with Machine Screws. Note: Drawer assembly is not complete until 3/4” Flat Head Screws are used in a later step. Handle Part List MS.
( Assembly Instructions 10/15 ) Drawer STEP 17 Attach Drawer Sides (M3), {M4) and Supports (Mé) to Drawer Back (M2) TN 1 /4" Flat Head Se row with 1 1/4" Flat Head Screws. STEP 18 Insert Drawer Bottom (O5) into groove. Attach Drawer Front {O1) to unit with 1 1/4" Flat Head Screws. STEP 19 Attach Handle with Machine Screws. \ Handle Note: Drawer assembly is not complete until 3/4” Flat Head Screws are used in a later step. Part List Drawer Front Drawer Back Drawer Side Drawer Side Drawer Bottom Support spec.
( Assembly Instructions 11/15 ) Drawer STEP 20 Attach Drawer Sides (M3), {M4) and Supports (Mé) to Drawer Back (M2) TN 1 /4" Flat Head Se row with 1 1/4" Flat Head Screws. STEP 21 Insert Drawer Bottom (O5) into groove. Attach Drawer Front {P1} to unit with 1 1/4" Flat Head Screws. STEP 22 Attach Handle with Machine Screws. \ Handle Note: Drawer assembly is not complete until 3/4” Flat Head Screws are used in a later step. Part List Drawer Front Drawer Back Drawer Side Drawer Side Drawer Bottom Support spec.
( Assembly Instructions 12/15 ) Drawer STEP 23 Attach Drawer Sides (M3), {M4) and Supports (Mé) to Drawer Back (M2) TN 1 /4" Flat Head Se row with 1 1/4" Flat Head Screws. STEP 24 Insert Drawer Bottom (O5) into groove. Attach Drawer Front {Q1) to unit with 1 1/4" Flat Head Screws. STEP 25 Attach Handle with Machine Screws. \ Handle Note: Drawer assembly is not complete until 3/4” Flat Head Screws are used in a later step. Part List Drawer Front Drawer Back Drawer Side Drawer Side Drawer Bottom Support spec.
( Assembly Instructions 13/15 ) Drawer STEP 26 Attach Drawer Sides (M3), {M4) and Supports (Mé) to Drawer Back (M2) TN 1 /4" Flat Head Se row with 1 1/4" Flat Head Screws. STEP 27 Insert Drawer Bottom (O5) into groove. Attach Drawer Front {R1) to unit with 1 1/4" Flat Head Screws. STEP 28 Attach Handle with Machine Screws. \ Handle Note: Drawer assembly is not complete until 3/4” Flat Head Screws are used in a later step. Part List Drawer Front Drawer Back Drawer Side Drawer Side Drawer Bottom Support spec.
( STEP 29 Loosen slightly screws per-installed on back of drawer fronts. Assembly Instructions 14/15 STEP Insert drawers into unit, then adjust ~ L2 drawer front panels left or right and up or down until drawer gaps look o proportional. STEP 31 Pull each drawer open slowly, then re-tighten screws from Step 29. Make sure drawer front panels do not move and lock drawer front panels into position with 3/4" Flat Head Screws. Note: These 3/4" Flat Head Screws must be installed to complete the drawer assembly.
CARE INSTRUCTIONS NEVER NEVER allow liquids 1 remain on furniture, usé glass cleaners on Absorption causes parts to warp finished furniture, Ammonia and split and finishes to laminate. chemically attacks the finish. Do not write directly on surface. PREVENT MARKING Do not use power tools above 8 volts to assemble. PREVENT CRACKING K Do not page hot objects on surface.
20 05185 0431 home styles’ Dresser IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. ( . ) Part List M1. N1, Drawer Front Drawer Front 1pe. F. Front Rail 1pc. o1. P1. I Drawer Front Drawer Front Front Rail H. 1pe. 1pc. Front Rail Q1. R1. Drawer Front Drawer Front 1pe.
& 20051850078 v . Mirror IMPORTANT Cara fully remove all the parts from the carton and place them individually on a soft doth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. £ . N Part List B. Mirror Support | 2 pes.
( Assembly Instructions 2/3 ) IMPORTANT = Uiz 3 soft cloth between these parts and the floor. = Do not use power toots above 8 vols to assemble, » Do not tighten 2l the bolts until each part is properly assembled, ® Keep Hex Wrench as the bolts may need to be tightened in the future. STEP 1 Place Mirror {A} face down on a soft cloth. Attach Mirror Supports (B} to Mirror (A) with Head Cap Bolts, Spring Washers and Flat Washers, Tighten boils with Hex Wrench.
( Assembly Instructions 3/3 ) STEP 2 Attach unit to Dresser with Head Cap Bolts, Spring Washers and Flat Washers. Tighten bolts with Hex Wrench.
