5450-501 Platform Bed ben IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. © I "5 Part List A Top Rail 1pe. B. Head Panel 1pe E. Bottom Rail 1pe. Hardware List 8 rl Méxt5 & Sail Cam Lock Cam Lock Crow Heed Gap Bolt {hart} Spring Washer Dowse Hu Wrench Hax Wrench L pests.
( Assembly Instructions 2/3 ) IMPORTANT = Lie 3 soft cloth between these parts and the floor. = Do not use power tools above 8 volts to assemble, » Do not tighten al the bolts until each part is properly assembled, © The unit must be level to work properly. Use the included adjustable levelers to level. © Keep Hex Wrench as the bolts may need to be tightened in the future. STEP 1 foam Lock Screw Insert Cam Lock Screws into the per-drilled holes in Top Rail (A) and Posts (C), {D).
( Assembly Instructions 3/3 ) Head Cap Bot short} Tea Spring Washer STEP 3 Attach Post (C) to unit with Dowels, Cam Locks, Head Cap Bolts {short} and Spring Washers. Attach Bottom Rail (E) to unit with Head Cap Bolts {short} and Spring Washers. Attach Post {D) to unit with Dowels, Cam Locks, Head Cap Bolts (short) and Spring Washers. Tighten all bolts with Hex Wrench. {See Figure 2) To complete assembly see instructions in carton 5450-502. HE.
450-502 Platform Bed ben IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List Stretcher 1 pe G. Side Rail A H. Middle Rail Side Rail 1pe 1 pe F. Foot Frame 1pe \ A (Hardware List «7 fe or” Sal Head Cap Bolt fang} Head Cop Bolt Hand Cap Belt (short) Spring Washer C
( Assembly Instructions 2/5 ) IMPORTANT = Lie 3 soft cloth between these parts and the floor. = Do not use power tools above 8 volts to assemble, » Do not tighten all the bolts until each part is properly assembled, © The unit must be level to work properly. Use the included adjustable levelers to level. © Keep Hex Wrench as the bolts may need to be tightened in the future. * Do not slide bed on floor. To move assembled bed requires two people. Remove any bedding, then Ii and carry bed.
( Assembly Instructions 3/5 ) STEP 5 Attach Side Rails {G), (H) and Middle Rail {} to Stretcher (K) with Head Cap Bolts {short} and Spring Washers, tightening bolts only halfway. {See Figure 4} #y4—— Head Cap Bolt {short} hb 2 Spring Washer I Head Cap Bat short) Spring Washer Head Cap Bot (hart) rd STEP 6 Attach Foot Frame {F} to unit with Head Cap Bolts (short), tightening bolts only halfway. Tighten al! bolts used in Steps 5 and 6.
( Assembly Instructions 4/5 ) STEP 7 Turn unit over to its upright position. Attach headboard to unit with Head Cap Bolts {long} and Head Cap Bolts (short), tightening bolts only halfway.
( Assembly Instructions 5/5 ) Head Cop Bait STEP 8 Attach Slats {J} to unit with Head Cap Bolts. Figure 5 Tighten all bolts with Hex Wrench. Level unit by adjusting the adjustable levelers on bottom of unit. (See Figure 5} Note: Do not slide bed on floor. Te move assembled bed requires two people.
