20 05502 0070 Lt . Vanity with Mirror IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power to's above 8 volts to assemble. , Part List D. Front Rail 1pe. E. F. L Side Panel Side Panel Side Panel Side Anal 1pe. Refer to later pages) of these .
( Assembly Instructions 2/10 ] IMPORTANT # Use a soft cloth between these parts and the floor, + Do nat use power tools above B volts to assemble. = Do nat tighten all the screws until each part's properly assembled. ® The unt must be level to work properly. Use the included adjustable levelers to elev. ® Keep Hex Wrench as the Bolts may need to tightened in the future.
( Assembly Instructions 3/10 ] STEP 3 Attach unit and Side Panels (E) and (F) to Back Panel (i) with Cam Locks. STEP 4 Attach Bottoms {I} and (J) to unt with Dowels and 1 1/2" Round head Screws.
instructions 4/10 Assembly | STEP 5 Attach Legs (1) to unit. STEP 6 Tum unit over to its Attach Top {C) to unit with Dowels and Cam Locks, upright position.
( Assembly Instructions 5/10 ] STEP Attach Battens (B) to Mirror (A) and unit with Bolts, Spring Washers and Flat Washers. Tighten Bolts with Hex Wrench. (See Figure 2) Level unit by adjusting the adjustable levelers on bottom of unt.
( Assembly Instructions 6/10 ] IMPORTANT = To help reduce the risk of the unit tipping over, the Tip-over Restraint must be installed following these instructions exactly. STEP 8 Place unit at desired location. Mark wall with pencil to show position of hole in Back Pane! (K). (See Figure 4) Move unit. Drill a 3/8” hole in wall 1” below mark. Insert Anchor ‘nto the wall hole and attach Tip-over Restraint to Anchor with 1 1/2" Round Head Screw and Flat Washer.
( Assembly Instructions 7/10 ] Drawer (M) STEP 9 Attach Drawer Sides (M3) and (M4) to Drawer Back (M2) with 1 1/4" Flat Head Screws. STEP 10 Insert Drawer Bottom (M5) into groove. Attach Drawer Front (M1) to unit with 11/4" Flat Head Screws. STEP 11 Attach Handle with Machine Screw. STEP 12 Place Jewelry Box (Mé) into position. Note: Drawer assembly is not complete until 3/4” Flat Head Screws are used in a later step.
( Assembly Instructions 8/10 ] Drawer (N) STEP 13 Attach Drawer Sides (N3), {N4} and . Drawer Support (N6) to Drawer Back (N2) > y with 1 1/4" Flat Head Screws. Roller at back “Ra 14° Flt Hod Screw STEP 14 Insert Drawer Bottom {N5} into groove. Attach Drawer Front (N1) to unit with 11/4" Flat Head Screws. STEP 15 Attach Knobs with Machine Screws. Note: Drawer assembly is not complete until 3/4” Flat Head Screws are used in a later step.
( Assembly Instructions 9/10 ] STEP 16 For Drawers (M) loosen slightly upper center screw and uninstall lower center screw. For Drawer (N} loosen slightly screws per-installed on back of drawer front. aN ZI STEP 17 Insert drawers into unit, then ome adjust drawer front panels left or right and up or down until drawer gaps look proportional. elm STEP 18 Pull each drawer open slowly and re-tighten screws from Step 16.