20 05504 0431 Dresser Ta IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. E. Front Rail 1 pe. (Part List . | G Back Panel Front Rail Front Rail J. 1pe o1.
0 05504 0432 Ta Dresser IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. art List Drawer Side Drawer Back 2 pes. 2 pes. pes M4. P Drawer Side B 2 pes. Side Panel spec \ C. NB. Side Panel Drawer Bottom Drawer Support 1 pe. 2 pes. é pes. 02. 03.
( Assembly Instructions 2/11 ) IMPORTANT = Use a soft clutch between these parts and the floor. = Do not use power tools above 8 volts to assemble. = Do not tighten all the screws until each part is properly assembled, o The unit must be level to work properly. Use the included adjustable levelers to level. STEP 1 Insert Cam Lock Screws into per-drilled holes in Top (A), Side Panels (B), {C), Front Rails {F}, (G), Back Panels (I), {J} and Bottom (K}, then tighten.
( Assembly Instructions 3/11 ) STEP 2 Attach Back Panel (I) to Back Pane! (J).
( Assembly Instructions 4/11 ) STEP 4 Attach Front Rails (F), (G) to unit with Cam Locks and Front Rails (E), (H} to unit with 1 1/4" Round Head Screws. STEPS Attach Side Panels (8) and {C} to unit with Can Locks.
( Assembly Instructions 6/11 ) STEP 8 Turn unit to its upright position. * Round Head Screw 1" Round Hea Attach Top (A} to unit with Cam Locks and 1" Round Head Screws. Carr Lock STEPS Lee! unit by adjusting the adjustable levelers on bottom of feet. (See Figure 2) Note: Unit must be level to proceed.
( Assembly Instructions 7/11 IMPORTANT = Ta help reduce the risk of the unt tipping over, the Tip aver Restraint must be installed following these instructions exactly. STEP 10 Place unit at desired location. Mark wall with pencil just above and in-line with hole in Top (A). (See Figure 3) Move unit. Drill a 3/8” hole in wall 1 1/2” below mark. Insert Anchor into the wall hole and attach Tip over Restraint to Anchor with 1 1/2” Round Head Screw and Flat Washer.
( Assembly Instructions 8/11 ) Drawer (Nj) STEP 11 Attach Drawer Sides (N3), {N4} and Drawer Support (Né} to Drawer Back (N2) with 1 1/4" Flat Head Screws. “wd——1 1/4" Fiat Head Screw STEP 12 & 1/4" Fiat Head Screw Insert Drawer Bottom (NE) into groove, Attach Drawer Front (N1} to unit with 1 1/4" Flat Head Screws. STEP 13 Attach Knobs with Machine Screws. Note: Drawer assembly is not complete until 3/4” Flat Head Screws are used in a later step.
( Assembly Instructions 9/11 ) Drawer (O) STEP 14 Attach Drawer Sides (03), {04} and . Drawer Support (N68) to Drawer Back (02) 1A" Fiat Head Screw with 1 1/4" Flat Head Screws. STEP 15 1144 Fist Hod Screw Insert Drawer Bottom (O35) inch groove. < Attach Drawer Front {O1) to unit with A 1 1/4" Flat Head Screws. 2 | STEP 16 Attach Knobs with Machine Screws. Note: Drawer assembly is not complete until 3/4" Flat Head Screws are used in a later step.
( Assembly Instructions 10/11 ) STEP 17 Loosen slightly screws per-installed on back of drawer fronts, STEP 18 Insert drawers into unit, then adjust drawer front panels left or right and up or down until drawer gaps look proportional. STEP 19 Pull each drawer open slowly, then re-tighten screws from Step 17. Make sure drawer front panels do not move and lock drawer front panels into position with 3/4" Flat Head Screws. Note: These 3/4" Fiat Head Screws must be installed to complete the drawer assembly.
CARE INSTRUCTIONS NEVER NEVER alley liquids to remain on furniture. use glass cleaners ori Absorption causes parts to warp finished furniture. Ammonia and split and finishes to laminate. chemically attacks the finish. EN Do not use power tools Do not place Do not write above 8 volts to assemble. indirect sunlight. directly on surface. PREVENT PREVENT PREVENT CRACKING FADING MARKING 1 Do not place hot objects on surface.