a 20 05506 0010 LT Ty Entertainment Center IMPORTANT Carefully remove all the parts from the carton and place therm individually on a soft cloth to prevent scratches or other damage. Carefully and strictly fol ow these assembly instructions to ensure a completed product as designed. De not use power tools above 8 volts to assemble. Part List Middle Panel Middle Panel 1 pe. 8. Side Panel 1pe Panel = Door Toe ‘anal H. 1 pe. Door Bottom Panel Back Pane Back Panel 1pe 2 pes. 1pe Hardware List .
( Assembly Instructions 2/9 ) IMPORTANT ® Use a soft cloth between these parts and the floor. = Do not use power too's above 8 volts to assemble. » Do nat tighten all the screws until each part is properly assembled, o The unit must be level to work properly. Use the included adjustable levelers to level. STEP 1 Insert Cam Lock Screws into per-drilled holes in Top (A} and Side Panels (B), (C), then tighten, J Can Lock Resew STEP 2 Attach Middle Panels (F) and (G) to Top (A) with Dowels and Cam Locks.
( Assembly Instructions 3/9 ) STEP 3 Slide Back Panels (J) and (K) nto groove. STEP 4 = 2 Attach Bottom Panel {L) to unit with Dowels and 1 1/4" Round Head Screws.
( Assembly Instructions 4/9 ) Bows STEPS Attach Side Panel (B} to unit with Dowels and Cam Locks. STEP & Attach Bottom Calls (N) and (0) to unit with Dowels and Cam Locks. Attach 1 1/4" Round Head Screws to unit.
( Assembly Instructions 5/9 ) STEP 7 Attach Side Panel {C) to unit with Dowels and Cam Locks. STEP 8 Attach Bottom (M) to unit with 1" Round Head Screws.
( Assembly Instructions 6/9 ) STEP 9 Tum unit to its upright position, Level unit by adjusting the adjustable levelers on bottom of unit. {See Figure 2) Note: Unit must be level to proceed. Attach 1/2" Flat Head Screws to unit. Attach Wedges to unit with 1/2" Flat Head Screws. {See Figure 3} Wedge. 172" Flat Dash Screw.
( Assembly Instructions 7/9 ) IMPORTANT » Ta help reduce the risk of the unit tipping aver, the Tip over Restraint must be installed following these instructions exactly. STEP 10 Place the unit at desired location. Mark wall with pencil to show position of hole in Back Pane! (K}. (See Figure 4) Move unit. Drill a 3/8" hole in wall 1” below mark. Insert Anchor into the wall hole and attach Tip over Restraint to Anchor with 1 1/2" Round Head Screw and Flat Washer.
( Assembly Instructions 8/9 ) STEP 11 Insert Adjustable Pins into side panels and middle panels at desired level, Place Shelves {D) and (E} into position. Hinge Se 1/2 Round Head Screw “po Machine Screw Han die STEP 12 Attach Hinges to Doors (H) and {I} with 1/2" Round Head Screws. Attach Handles to Doors {H) and {I} with Machine Screws.
( Assembly Instructions 9/9 ) STEP 13 Attach Doors (H} and to unit with 1/2" Round Head Screws into ova & holes 'n hinge. (See os 1/2" Round Head Screw Figure § Figure 10 If needed, adjust doors up or down by loosening slightly 1/2" Round Head Screws from side panel, adjusting doors up or down and re-tightening screws. (See Figure 9) If needed, adjust doors left to right. (See Figure 10} if needed, adjust doors front to back.
