I 2005520 0561 hei Bunk Bed IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List A. Lower End Panel 1 pe Lower End Panel (For assembly see instructions in carton 20 05520 0563. Home Styles Customer Service: 888-680-7440, 877-831-0319 88.
i 2005520 0562 hei Bunk Bed IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. r ” ~N Part List D. E. Upper End Panel Upper End Panel 1pe. 1 pe. F. Upper Slats 1pe. \. J ~ (For assembly see instructions in carton 20 05520 0563.
20 05520 0563 Bunk Bed ben IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List G. H. Lower Panel Upper Panel 2 pes. 2 pes. Hardware List » Sy Ena Rdx15 [Le Hex Wrench Small Hex Wrench Head Cap Bolt {Lang} Head Cap Bolt {short} Head Cap Alt Square Washer 1pe 1 pe.
( Assembly Instructions 2/6 ) IMPORTANT = Lie 3 soft cloth between these parts and the floor. = Do not use power tools above 8 volts to assemble, » Do not tighten all the bolts until each part is properly assembled, © The unit must be level to work properly. Use the included adjustable levelers to level. © Keep Wrench and Hex Wrench as the Nuts and Head Cap Bolts may need to be tightened in the future.
( Assembly Instructions 3/6 ) STEP 3 Attach Legs {K} to Rails (J) Head Cap Bot ong) with Head Cap Bolts {long}. ) {See Figure 2} Figure 2 STEP 4 Insert units from Step 3 into unit from Step 2. STEPS Attach Lower Fiats {C) to unit with Wood Screws. {See Figure 3} Level unit by adjusting the adjustable levelers on bottom of legs. {See Figure 4} Figure 4 88.
( Assembly Instructions 4/6 ) STEP 6 insert Bolts into per-drilled holes in Guardrails (1), then tighten. Head Cap Bolt short) =e, STEP 7 Attach Upper Panels (H) to Guardrails {I} with Flat Washers, Nuts, Connector Plates and Head Cap Bolts {short}. (See Figures 5 and 6} Figure 5 Head Cap Bolt Acquaints Washer STEP 8 Figure 7 Attach units to Upper End Panel (E} with Head Cap Bolts {gong, Square Washers and Head Cap Bolts, tightening bolts only halfway. (See Figure 7) 88.
( Assembly Instructions Head Cap Bit Square Washer STEP 9 Attach Upper Panel (D) to unit with Head Cap Bolts (long), Square Washers and Head Cap Bolts, tightening bolts only halfway. Tighten all bolts used in Steps 7, 8 and 9. STEP 10 Attach Upper Slats {F} to unit with Wood Screws. 88.
( Assembly Instructions 6/6 ) STEP 11 Insert Metal Pins into per-drilled holes in unit from Step 5. Attach unit from Step 10 to unit from Step 5 with Metal Pins. Note: If back of bunk bed is placed next to a wall, the full length guardrail must be placed against the wall to prevent entrapment between bunk bed and wall. (To complete assembly see instructions in carton 20 05520 0565. ) 88.
IMPORTANT Important Use only mattress which is 747 = 78% long and 37 1/20 S38 120 wide an upper bunk. Use malformations which long and 53 1/2 wide on lower bunk Use only mattress which is 107 or less thick on tipper bunk. Replacement parts, including additional guardrails may be obtained from Home Styles Customer Service at www home styles-furnitire com! Safety Warnings Follow the information on the misapprehending on ‘thé upper bunk end structures arid dr the darter. Donor remove warning label from’ bed.
IMPORTANTES Importantes Utilisez uniquement des matelas gui este 74” 75% de long 4 38 1/2" de large sur fa couchette. Utilisez Uniquement des matelas cuites de 745 + 757 décongestion 1720 = 53 1/2" de large sur des [its superposés: Utiliser Uniquement dentelaires gui est de 10% ou moins épale sur Ja couchette. Pictes de replacement, y.
CARE INSTRUCTIONS NEVER NEVER allow lipids to remain on armature. {ise glass Cleaners on Absorption causes parts to warp finished furniture: Ammonia and. split and finishes to laminate. chemically attacks the finish, = Diana place direct sunlight. PREVENT FADING Da anti directly on surface.
20 05520 0564 Bunk Bed ben IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. 's ~ Part List _— Ni. Riser 2 pes, Back Panel << Riser pes. Stair Riser 4. pe. Back Panel Stair Divider ; ) 4 pes. Side Pane! h P 1pe Le 05. Back Panel P. L3. — Middle Panel | P Stair = 2 pes.
WE 20 05520 0565 Bunk Bed IMPORTANT Cara fully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. { . Ny Part List u Upright RY. Stair Panel az. 1pe Back Panel Back Panel Stair Panel Stair Panel Refer to later pages) of these 1 pe 2 prs. Instructions for drawer assembly.
( Assembly Instructions 2/12 ) IMPORTANT = Use a soft cloth between these parts and the floor. = Da not use power tools above 8 volts to assemble. + Do not tighten zl the bolts until each part is properly assembled, o The unit must be level to work properly. Use the included adjustable levelers to level. © Keep Wrench and Hex Wrench as the Nuts and Head Cap Bolts may need to be tightened in the future. Follow instructions in carton 20 05520 0563 first, then proceed with Step 12.
( Assembly Instructions 3/12 ) STEP 13 Attach Middle Panels {P) to Rails ($1) and (52) with Cam Locks. {See Figure 9) Note: A Philips screwdriver 5” or less in length is recommended, “Figure 9 STEP 14 Attach Riser {N3} to unit with Cam Locks. STEP 15 Attach Stair {L5) to unit with Cam Locks.
Assembly Instructions 4/12 STEP 16 Attach Riser {N2} and STEP 17 Attach Stair {L4) to unit with Cam Locks. pe STEP 18 Attach Riser {N1)} and Divider {QO} to unit with Cam Locks.
( Assembly Instructions 6/12 ) STEP 22 Slide Back Panels {02}, (Q3), (Q4) and (Q5) into position. STEP 23 2 IN) Attach Side Panel {(M) and a Riser (N1} to unit with STEP 24 Slide Back Panel (Q1) into position. Attach Stair (L1) to unit with Cam Locks.
( Assembly Instructions 7/12 ) STEP 25 Assemble Stair Panels (R3), Stair All (T) and Upright (U) with Head Cap Bolts (long), tightening bolts only halfway. (See Figure 10) Head Cap Bok (ng) ——>4 Figure 10 Head Cap Lott for Sui \ STEP 26 Attach unit from Step 25 and Stair Panel {R2) to unit from Step 24 with Head Cap Bolts for Stair, tightening bolts only halfway. Head Cap Bolt (medium Head Cap Holt {ong} STEP 27 Attach Head Cap Bolt (long) to unit, tightening bolt only halfway.
( Assembly Instructions 8/12 ) STEP 28 Attach Drawer Side {V3} to Drawer Front (V1) and Drawer Back (V2) with 11/4" Flat Head Screws. STEP 29 11/4" Flat Head Screw 8" _ Insert Drawer Bottom (V5) ~. into groove. Attach Drawer Side (V4) to unit with 1 1/4" Flat Head Screws. STEP 30 Attach Handle with Machine Screws. no Note: Drawer assembly is not complete until 3/4” Flat Head Screws are used in a later step. Part List Drawer Front Drawer Back Drawer Side Drawer Side Drawer Bottom 1 pe. 1pe 1 pe. 1pe.
( Assembly Instructions 9/12 ) STEP 31 Attach Drawer Side {V3} to Drawer Front (W1) and Drawer Back (W2) with 11/4" Flat Head Screws. STEP 32 Insert Drawer Bottom (W5) into groove. Attach Drawer Side (V4) to unit with 1 1/4" Flat Head Screws. STEP 33 Attach Handle with Machine Screws. no Note: Drawer assembly is not complete until 3/4” Flat Head Screws are used in a later step. Part List Nay Drawer Front Drawer Back Drawer Side Drawer Side Drawer Bottom 2 pes, 2 pes, 2 pes. apes. apes.
( Assembly Instructions 10/12 / Head Cap Bolt {medium} A ?, STEP 34 “ee oms Head Cap Lott {ong} Attach unit from Step 27 to bunk bed unit with Head Cap Bolts {long) and Head Cap Bolt (medium), tightening bolts only halfway. Tighten all bolts. Slide Drawers (V} and (W) into position.
( Assembly Instructions 11/12 ) IMPORTANT = To hap reduce the risk of the unit tipping over, the Tip over Restraint must be installed following these instructions exactly. Bracket at STE Pp 35 top of unit 3/8” wall hole Bracket on wall Wall Se raw Pro-drill Rancher in wa Tie end Lock end holey at top of uni Place unit at desired location. Drill a 3/8” hole in wall in-line with 0 per-drilied hole on back of Stair Panel (R1). Move unit.
( Assembly Instructions 12/12 ) STEP 36 Loosen slightly screws per-installed on back of drawer fronts. To STEP 37 Insert drawers into unt, then adjust drawer front panels left or right and up or down until drawer gaps look proportional. STEP 38 Pull drawers open slowly, then re-tighten screws from Step 36. Make sure drawer front panels does not move and lock drawer front panels into position with 3/4" Flat Head Screws. Note: These 3/4" Flat Head Screws must be installed to complete the drawer assembly.
IMPORTANT Important Use oly mattress whit 1s 747 87 Lang and 37 170° = 384000 wide on Upper bunk Use only mattress chichis 747 « 787 long and 82 1727 53 1/27 wide onl lower boink. Use only mattress chichis 10" or lass thick on upper bunk: Replacement parts, including additional guardrails may be obtained from Home Styles Customer Service at waivchomaestyles-furniture com Safety Warnings Follow the formation on the warnings appearing on the upper bunk and structure and an the carton.