20 05520 0932 Storage Island IMPORTANT Part List D. Back Panel 1 pc. E. Back Panel 1 pc. F. Middle Panel 1 pc. G. Side Panel 1 pc. H. Side Panel 1 pc. Hardware List Hex Wrench 1 pc. Cam Lock 45 pcs. (+6 extra) Flat Washer 14 pcs. (+1 extra) Spring Washer 14 pcs. (+1 extra) M6x32 Head Cap Bolt 14 pcs. (+1 extra) Handle 8 pcs. Small Hex Wrench 1 pc. Cam Lock Screw 45 pcs. (+2 extra) Adjustable Pin 24 pcs. (+1 extra) M3.5x32 Wood Screw 4 pcs. (+1 extra) M4x16 Machine Screw 16 pcs.
Assembly Instructions 2/9 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Hex Wrench as the bolts may need to be tightened in the future.
Assembly Instructions 3/9 Cam Lock STEP 2 E Attach Back Panels (D) and (E) to Middle Panel (F) with Cam Locks. (See Figure 2) F D Figure 2 Head Cap Bolt Spring Washer Flat Washer STEP 3 Attach Bottom (J) to unit with Flat Washers, Spring Washers, Head Cap Bolts and Cam Locks, tightening bolts only halfway.
Assembly Instructions 4/9 Cam Lock I I STEP 4 Attach Plinths (I) to unit with Cam Locks. B Flat Washer Spring Washer B Head Cap Bolt STEP 5 Attach Rails (C) to Side Panel (H) with Cam Locks. Attach unit from Step 4 to unit with Cam Locks, Flat Washers, Spring Washers and Head Cap Bolts, tightening bolts only halfway. C C C Attach Rails (B) to unit with Wood Screws.
Assembly Instructions 5/9 Wood Screw STEP 6 G Attach Rails (C) to unit with Cam Locks. Attach Side Panel (G) to unit with Cam Locks Flat Washers, Spring Washers, Head Cap Bolts and Wood Screws, tightening bolts only halfway. C Turn unit to it’s upright position. C C Flat Washer Spring Washer Head Cap Bolt Cam Lock A Flat Washer Spring Washer Head Cap Bolt Cam Lock STEP 7 Attach Top (A) to unit with Cam Locks, Flat Washers, Spring Washers and Head Cap Bolts, tightening bolts only halfway.
Assembly Instructions 6/9 Drawer (L) STEP 8 L4 Attach Drawer Sides (L3) and (L4) to Drawer Back (L2), then flip Locks. (See Figures 4 and 5) L3 L2 Lock STEP 9 Figure 4 Figure 5 Slide Drawer Bottom (L5) into groove. L1 Attach Drawer Front (L1) to unit, then flip Locks. L5 Lock Machine Screw STEP 10 Attach Handle with Machine Screw. Handle Part List L1. Drawer Front 2 pcs. L2. Drawer Back 2 pcs. L3. Drawer Side 2 pcs. L4. Drawer Side 2 pcs. L5. Drawer Bottom 2 pcs.
Assembly Instructions 7/9 Drawer (M) M4 STEP 11 M3 M2 Attach Drawer Sides (M3) and (M4) to Drawer Back (M2), then flip Locks. Lock STEP 12 M1 Slide Drawer Bottom (M5) into groove. M5 Attach Drawer Front (M1) to unit, then flip Locks. Lock Machine Screw STEP 13 Attach Handle with Machine Screw. Handle Part List M1. Drawer Front 6 pcs. M2. Drawer Back 6 pcs. M3. Drawer Side 6 pcs. M4. Drawer Side 6 pcs. M5. Drawer Bottom 6 pcs.
Assembly Instructions 8/9 L M L M M M M M STEP 14 Level unit by adjusting the adjustable levelers on bottom of unit. (See Figure 6) Note: Unit must be level to work properly. Slide Drawers (L) and (M) into position. Figure 6 Adjustable Pin K K K STEP 15 K K K Insert Adjustable Pins into side panels and middle panel at desired level. Place Shelves (K) into position.
Assembly Instructions 9/9 Per regulatory requirements, a Tip-over Restraint is included. Follow Step 16 to install it. STEP 16 Drill a 3/16” hole 1/2” deep 1” below top of unit in middle of side panel that is against a wall. Anchor in wall Bracket on wall Wall Screw 3/8” wall hole 3/16” hole in side panel of unit Wood Screw Place unit at desired location. Drill a 3/8” hole in wall in-line with 3/16” hole drilled in side panel. Tie end Move unit.
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.