20 05533 0432 home styles’ Dresser IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. ( hp Part List K. Middle Support Drawer Side Drawer Back : PCs. 2 pes. C. Side Panel 1pe. D. Divider 4 D Od rawer Side ~ P3. P2. Drawer Side Drawer Back 2 pes. % apes. Apes.
( Assembly Instructions 2/10 ) IMPORTANT « Use a soft cloth between these parts and the floor. « Do not use power tools above 8 volts to assemble. = Do not tighten all the screws until each part is properly assembled. « The unit must be level to work properly. Use the included adjustable levelers to level. Cam Lock Screw—>§ STEP 1 Insert Cam Lock Screws into per-drilled holes of Top (A), Side Panels (B), (C), Front Rails (E), (F} and Back Rails (H), {I}, (J), then tighten. Dx.
( Assembly Instructions 3/10 ) STEP 2 Attach Middle Support (K) to Divider (D} with 1 1/4" Round Head Screws and Wooden Dowels. STEP 3 Attach Front Rails (E), (F) and Back Rails (H), (1), (J) to unit with Cam Locks.
( Assembly Instructions 4/10 ) STEP 4 Attach Side Panels (B} and {C) to unit with Cam Locks. Attach Center Leg (lL) to STEP 5 Attach Top (A) to unit with Cam Locks, 1 1/2" Round Head Screws and Wooden Dowels. Attach Plinth (G) to unit with 1 1/4" Round Head Screws and Wooden Dowels. Dx.
( Assembly Instructions 5/10 ) STEP 6 Level unit by adjusting the adjustable levelers on bottom of unit. {See Figure 2) Note: Unit must be level to work properly. Attach Back Panels {M} and {N) to unit with 1/2" Round Head Screws and Flat Washers. Figure 2 Dx.
( Assembly Instructions 6/10 ) IMPORTANT « To help reduce the risk of the unit tipping over, the Tip-over Restraint must be installed following these instructions exactly. STEP 7 Place unit at desired location. Mark wall with pencil just above and in-line with hole in Back Panel (M). {See Figure 3) Move unit. Drill a 3/8" hole in wall 2 1/2” below mark. Insert Anchor into the wall hole and attach Tip-over Restraint to Anchor with 1 1/2" Round Head Screw and Flat Washer.
( Assembly Instructions 7/10 ) Drawer (O) . STEP 8 Attach Drawer Side (O03) to Drawer Front (O1} and Drawer Back (02) with 1 1/4" Flat Head Screws. Roller at back——» 3%. y Fiat Head Screw STEP 9 Insert Drawer Bottom (O5) into groove. Attach Drawer Side (04) to unit with 1 1/4" Flat Head Screws. STEP 10 Attach Support (06) to unit with 1 1/4" Flat Head Screws. 7 Sal Handiness» STEP 11 \. 1/4" Flat Head Screw Note: Drawer assembly is not complete until 3/4” Flat Head Screws are used in a later step.
( Assembly Instructions 8/10 ) Drawer 1/4" Fiat Head Screw STEP 12 Attach Drawer Side (P3) to Drawer Front (P1} and Drawer Back (P2) with 1 1/4" Flat Head Screws. 11/4" Fiat Head Screw STEP 13 Insert Drawer Bottom (P5) into groove. Attach Drawer Side (P4) to unit with 1 1/4" Flat Head Screws. STEP 14 Attach Support (06) to unit with 1 1/4" Flat Head Screws. <> ~~ Attach Large Handles with Machine Screws.
( Assembly Instructions 9/10 ) STEP 16 Loosen slightly the screws per-installed on back of drawer fronts. STEP 17 Insert drawers into unit, then adjust drawer front panels left or right and up or down until gaps look proportional. STEP 18 Pull each drawer open slowly and re-tighten screws from Step 16. Make sure drawer front panels do not move and lock drawer front panels into position with 3/4" Flat Head Screws. Note: These 3/4" Flat Head Screws must be installed to complete the drawer assembly. Dx.
CARE INSTRUCTIONS NEVER NEVER allow liquids 1 remain on furniture, us glass cleaners on Absorption causes parts to warp finished furniture, Ammonia and split and finishes to laminate. chemically attacks the finish. Do not write directly on surface. PREVENT MARKING Do not use power tools above 8 volts to assemble. PREVENT CRACKING 1 Do not page hot objects on surface.
