Instructions / Assembly

ManualsBrandsHOMESTYLES ManualsOutdoorsSanibel Swivel Black 7-Piece Cast Aluminum Outdoor Dining Set

Hardware List

Part List

6654-33

Dining Table

Top

1 pc.

Leg

4 pcs.

Stretcher

1 pc.

Tool(s) required for assembly: Level

IMPORTANT

Carefully remove all the parts from the carton and place them

individually on a soft cloth to prevent scratches or other damage.

Carefully and strictly follow these assembly instructions

to ensure a completed product as designed.

This product is made of aluminum. Do not use power tools

above 8 volts to assemble and only tighten bolts until snug.

Over tightening can damage the aluminum.

Hex Wrench

1 pc.

Small Hex Wrench

1 pc.

M8x30

Bolt

8 pcs. (+1 extra)

Flat Washer

16 pcs. (+1 extra)

Spring Washer

16 pcs. (+1 extra)

Nut

16 pcs. (+1 extra)

Cap

16 pcs. (+1 extra)

Cover

1 pc.

Wrench

1 pc.

styles Customer Service: www.homestylesfurniture.com,home

servicedesk@homestylesfurniture.com,

888-680-7460

Summary of content (8 pages)

PAGE 1
6654-33 Dining Table IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. This product is made of aluminum. Do not use power tools above 8 volts to assemble and only tighten bolts until snug. Over tightening can damage the aluminum. Part List A. Top 1 pc. B. Leg 4 pcs. C. Stretcher 1 pc. Hardware List Hex Wrench 1 pc.
PAGE 2
Assembly Instructions 2/3 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Wrench and Hex Wrench as the bolts and nuts may need to be tightened in the future.
PAGE 3
Assembly Instructions 3/3 Cap Nut Spring Washer Flat Washer Bolt Figure 2 STEP 2 A Place Top (A) upside down on a soft cloth. Insert Bolts into pre-drilled holes in Top (A), then tighten. (See Figure 2) Attach unit to Top (A) with Flat Washers, Spring Washers and Nuts, tightening Nuts only halfway. Tighten all Nuts used in Steps 1 and 2. Cover all Nuts with Caps. Cover STEP 3 Turn table over to its upright position. Cover umbrella hole with Cover.
PAGE 4
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.
PAGE 5
6654-53 Swivel Chair IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. This product is made of aluminum. Do not use power tools above 8 volts to assemble and only tighten bolts until snug. Over tightening can damage the aluminum. Part List D. Back 1 pc. F. Side Frame 1 pc. G. Side Frame 1 pc. E. Seat 1 pc. B.
PAGE 6
Assembly Instructions 2/3 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Wrench as the bolts may need to be tightened in the future. STEP 1 Place Side Frame (F) on a soft cloth.
PAGE 7
Assembly Instructions 3/3 STEP 3 Attach unit to Connector (B) with Bolts, Flat Washers (long), Spring Washers (large) and Nuts, tightening bolts and nuts only halfway. (See Figure 2) Tighten all Bolts and Nuts. Cover all Bolts and Nuts with Caps (large). Cap (large) B Bolt Flat Washer (long) Seat (A) Cap (large) Connector (B) Flat Washer (long) Spring Washer (large) Nut Figure 2 STEP 4 Place unit onto Base (C).
PAGE 8
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.