20 06659 0030 Dining Table IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. This product is made of aluminum. Do not use power tools above 8 volts to assemble and only tighten bolts until snug. Over tightening can damage the aluminum. Part List A. Top 1 pc. C. Stretcher 4 pcs. B. Leg 4 pcs.
Assembly Instructions 2/3 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Wrench as the nuts may need to be tightened in the future.
Assembly Instructions 3/3 STEP 2 Place Top (A) upside down on a soft cloth. Insert Bolts into pre-drilled holes in Top (A), then tighten. (See Figure 3) Cap Nut Spring Washer Flat Washer Attach unit to Top (A) with Flat Washers, Spring Washers and Nuts, tightening Nuts only halfway. Bolt Tighten all Nuts used in Steps 1 and 2. Cover all Nuts with Caps. A Figure 3 STEP 3 Cover Turn table over to its upright position. Cover umbrella hole with Cover.
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.
20 06659 0032 Dining Table IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. This product is made of aluminum. Do not use power tools above 8 volts to assemble and only tighten bolts until snug. Over tightening can damage the aluminum. Part List A. Top 1 pc. C. Stretcher 4 pcs. B. Leg 4 pcs.
Assembly Instructions 2/3 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Wrench as the nuts may need to be tightened in the future.
Assembly Instructions 3/3 STEP 2 Place Top (A) upside down on a soft cloth. Insert Bolts into pre-drilled holes in Top (A), then tighten. (See Figure 3) Attach unit to Top (A) with Flat Washers, Spring Washers and Nuts, tightening Nuts only halfway. Cap Nut Spring Washer Flat Washer Bolt Tighten all Nuts used in Steps 1 and 2. Cover all Nuts with Caps. A Figure 3 STEP 3 Cover Turn table over to its upright position. Cover umbrella hole with Cover.
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.
20 06659 0034 Dining Table IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List A. Top 1 pc. B. Leg 4 pcs. C. Stretcher 2 pcs. D. Stretcher 2 pcs. Hardware List Hex Wrench 1 pc. Small Hex Wrench 1 pc. Wrench 1 pc. Spring Washer 12 pcs.
Assembly Instructions 2/3 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Key Wrench in a safe place as the bolts may need to be tightened up in the future.
Assembly Instructions 3/3 Cap Nut Spring Washer Flat Washer Bolt A STEP 2 Turn Top (A) upside down on a soft cloth. Insert Bolts into pre-drilled holes in Top (A), then tighten. (See Figure 3) Attach unit to Top (A) with Flat Washers, Spring Washers and Nuts, tightening Nuts only halfway. Tighten all Nuts used in Steps 1 and 2. Figure 3 Cover all Nuts with Caps. Cover STEP 3 Turn table to its upright position. Cover umbrella hole with Cover.
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.
20 06659 0053 Swivel Chair IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. This product is made of aluminum. Do not use power tools above 8 volts to assemble and only tighten bolts until snug. Over tightening can damage the aluminum. Part List A. Back 1 pc. B. Connector 1 pc. C. Base 1 pc. D. Cushion 1 pc.
Assembly Instructions 2/3 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Wrench as the bolts may need to be tightened in the future. STEP 1 Attach Seat (A) to Connector (B) with Bolts, Flat Washers, Spring Washers and Nuts, tightening bolts and nuts only halfway.
Assembly Instructions 3/3 STEP 2 Place unit onto Base (C). Place Cushion (D) onto unit. D C STEP 3 Use velcro on Cushion (D) to attach to unit.
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.
20 06659 0080 Arm Chair IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. This product is made of aluminum. Do not use power tools above 8 volts to assemble and only tighten bolts until snug. Over tightening can damage the aluminum. Part List A. Back 1 pc. C. Arm 1 pc. D. Arm 1 pc. B. Seat 1 pc. E. Cushion 1 pc.
Assembly Instructions 2/3 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. Keep Hex Wrench as the bolts may need to be tightened in the future. STEP 1 Attach Seat (B) to Back (A) with Flat Washers, Spring Washers and Head Cap Bolts, tightening bolts only halfway.
Assembly Instructions 3/3 STEP 3 E Turn unit to its upright position. Place Cushion (E) onto unit. STEP 4 Use velcro on Cushion (E) to attach to unit. (See Figure 2) Level unit by adjusting the adjustable levelers on bottom of unit.
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.
20 06659 0083 Chaise IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List A. Seat 1 pc. B. Arm 1 pc. C. Arm 1 pc. D. Back Frame 1 pc. E. Support 1 pc. F. Axle 1 pc. G. Wheel 2 pcs. H. Cushion 1 pc. Hardware List M8x60 Head Cap Bolt (long) 2 pcs.
Assembly Instructions 2/5 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Wrench and Hex Wrench as the bolts may need to be tightened up in the future.
Assembly Instructions 3/5 Head Cap Bolt (long) Spring Washer Flat Washer D Flat Washer Spring Washer Head Cap Bolt C STEP 2 Place Back Frame (D) to unit with Flat Washers, Spring Washers and Head Cap Bolts (long), tightening bolts only halfway. Attach Arm (C) to unit with Flat Washers, Spring Washers, Head Cap Bolts and Head Cap Bolts (long), bolts only halfway. Tighten all bolts used in Steps 1 and 2.
Assembly Instructions 4/5 G Cap Head Cap Bolt (short) Spring Washer Flat Washer F G E Head Cap Bolt (small) Spring Washer (small) Flat Washer (small) STEP 3 Attach Support (E) to unit with Flat Washers (small), Spring Washers (small) and Head Cap Bolts (small), tightening bolts only halfway. Insert Axle (F) into unit. Attach Wheels (G) to unit with Flat Washers, Spring Washers and Head Cap Bolts (short), tightening bolts only halfway. (See Figure 2) Tighten all Head Cap Bolts.
Assembly Instructions 5/5 STEP 4 Turn unit over to its upright position. Place Cushion (H) onto unit. H STEP 5 Use velcro on Cushion (H) to attach to unit.
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.