Instructions / Assembly

ManualsBrandsHOMESTYLES ManualsOutdoor Lounge ChairsGrayton Gray Aluminum Outdoor Lounge Chair with Gray Cushion

Part List

6730-10

Chair

Side

1 pc.

Back Cushion

1 pc.

Non-slip Pad

1 pc.

Side

1 pc.

Rail

1 pc.

Seat Cushion

1 pc.

Hardware List

Small

Hex Wrench

1 pc.

Hex Wrench

1 pc.

Spring Washer

10 pcs. (+1 extra)

M6x35

Head Cap Bolt

6 pcs. (+1 extra)

M6x20

Head Cap Bolt (short)

4 pcs. (+1 extra)

Flat Washer

10 pcs. (+1 extra)

Cap

10 pcs. (+1 extra)

styles Customer Service: www.homestylesfurniture.com,home

servicedesk@homestylesfurniture.com,

888-680-7460

Seat

1 pc.

aaaaaa

IMPORTANT

Carefully remove all the parts from the carton and place them

individually on a soft cloth to prevent scratches or other damage.

Carefully and strictly follow these assembly instructions

to ensure a completed product as designed.

This product is made of aluminum. Do not use power tools

above 8 volts to assemble and only tighten bolts until snug.

Over tightening can damage the aluminum.

Summary of content (6 pages)

PAGE 1
6730-10 Chair IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. This product is made of aluminum. Do not use power tools above 8 volts to assemble and only tighten bolts until snug. Over tightening can damage the aluminum. Part List A. Seat 1 pc. B. Side 1 pc. C. Side 1 pc. F. Seat Cushion 1 pc. G.
PAGE 2
Assembly Instructions 2/5 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. Keep Hex Wrench as the bolts may need to be tightened in the future. Head Cap Bolt Spring Washer Flat Washer A D B Flat Washer Spring Washer Head Cap Bolt (short) STEP 1 Attach Rail (D) to Side (B) with Head Cap Bolts (short), Spring Washers and Flat Washers, tightening bolts only halfway.
PAGE 3
Assembly Instructions 3/5 Flat Washer Spring Washer Head Cap Bolt C Flat Washer Spring Washer Head Cap Bolt (short) STEP 2 Attach Side (C) to unit with Head Cap Bolts, Head Cap Bolts (short), Spring Washers and Flat Washers, tightening bolts only halfway. Tighten all bolts used in Steps 1 and 2. Cover all Head Cap Bolts with Caps.
PAGE 4
Assembly Instructions 4/5 aaaaaaaaa aaaaaaaaa aaaaa E aaaaaaaaaaaaaa aaaaaaaaaaaaaa aaaaaaaaaaaaaa STEP 3 Turn unit to its upright position. Place Non-slip Pad (E) into position.
PAGE 5
Assembly Instructions 5/5 G F STEP 4 Place Seat Cushion (F) into position. Place Back Cushion (G) into position. Cushion Care Instructions Keep cushions free of natural debris. Tip and angle cushions after use. Store cushions inside when not in use. Allow a minimum of 24 hours for wet cushions to air dry. Never use a hairdryer on cushions. Never put cushions in a clothes dryer. Cushion covers are hand wash and air dry only.
PAGE 6
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.