6800-83 Chaise IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List A. Cushion 1 pc. B. Seat 1 pc. C. Side 1 pc. D. Side 1 pc. F. Front 1 pc. G. Frame 1 pc. H. Back 1 pc. E. Foot 4 pcs. Hardware List Hex Wrench 1 pc. Small Hex Wrench 1 pc.
Assembly Instructions 2/4 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Hex Wrench as the bolts may need to be tightened in the future.
Assembly Instructions 3/4 Flat Washer Spring Washer Head Cap Bolt D STEP 3 Attach Side (D) to unit with Head Cap Bolts, Spring Washers and Flat Washers into unit, tightening bolts only halfway. Tighten all bolts used in Steps 1, 2 and 3. Head Cap Bolt Spring Washer Flat Washer E E E E STEP 4 Figure 2 Attach Feet (E) to unit with Head Cap Bolts, Spring Washers and Flat Washers.
Assembly Instructions 4/4 Toggle Toggle Figure 3 A Velcro Strap Tie-Down Figure 4 Velcro Strap STEP 5 Turn unit over to its upright position. aaaa aaaa Figure 5 Attach Cushion (A) to unit by pushing toggles through weaving in seat of unit. (See Figure 3) Attach Cushion (A) to unit with tie-downs. (See Figure 4) Attach Cushion (A) to unit with velcro straps. (See Figure 5) Level unit by adjusting the adjustable levelers on bottom of unit.
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.
800-20 End Table IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List A. Top 1 pc. B. Panel 2 pcs. D. Base 1 pc. C. Panel 2 pcs. E. Foot 4 pcs. Hardware List Hex Wrench 1 pc. (+1 extra) Small Hex Wrench 1 pc. M6x35 Head Cap Bolt 20 pcs.
Assembly Instructions 2/5 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Hex Wrench as the bolts may need to be tightened in the future. STEP 1 Attach Base (D) to Panel (B) with Head Cap Bolts, Spring Washers and Flat Washers, tightening bolts only halfway.
Assembly Instructions 3/5 Flat Washer Spring Washer Head Cap Bolt B STEP 3 Attach Panel (B) to unit with Head Cap Bolts, Spring Washers and Flat Washers, tightening bolts only halfway. Head Cap Bolt Spring Washer Flat Washer STEP 4 Insert Head Cap Bolts, Spring Washers and Flat Washers into unit, tightening bolts only halfway.
Assembly Instructions 4/5 Head Cap Bolt Spring Washer Flat Washer STEP 5 Attach Panel (C) to unit with Head Cap Bolts, Spring Washers and Flat Washers, tightening bolts only halfway. C Tighten all bolts used in Steps 1, 2, 3, 4 and 5. Head Cap Bolt Spring Washer Flat Washer E E E E Figure 2 STEP 6 Attach Feet (E) to unit with Head Cap Bolts, Spring Washers and Flat Washers.
Assembly Instructions 5/5 A STEP 7 Turn over unit to its upright position. Place Top (A) into position. Level unit by adjusting the adjustable levelers on bottom of unit.
CARE INSTRUCTIONS NEVER NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. Do not use power tools above 8 volts to assemble. Do not place in direct sunlight. Do not write directly on surface. PREVENT CRACKING PREVENT FADING PREVENT MARKING Do not place hot objects on surface. Do not use rubber based placemats. Do not use commercial waxes and polishes.
