Installation Guide

ManualsBrandsHomewerks Worldwide ManualsBathSingle Hole 1-Handle Low-Arc Bathroom Faucet in Chrome

Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-877-319-3757,

7 a.m. - 5 p.m., CST, Monday - Friday.

BASIN FAUCET

Español p. 5

08-13-2012

www.homewerksww.com

PACKAGE AND HARDWARE CONTENTS

PREPARATION

PART DESCRIPTION QUANTITY

A Faucet 1

B Hot index button 1

C Cold index button 1

AA Mounting nut 1

SAFETY INFORMATION

Please read and understand this entire manual before

attempting to assemble, operate or install the product.

CAUTION

• If you solder the joints during installation of the faucet,

the seats, cartridges, and washers must be removed

before using a ame or the warranty will be voided on

these parts.

• Cover the sink drain to avoid losing parts.

WARNING

• Protect your eyes with safety glasses when cutting or

soldering water supply lines.

Before beginning assembly of product, make sure all parts

are present. Compare parts with package contents list and

hardware contents. If any part is missing or damaged, do

not attempt to assemble the product. Contact customer

service for replacement parts.

Estimated Assembly Time: 30 minutes

Tools Required for Assembly (not included): Adjustable

Wrench, Groove Joint Pliers, Pipe Wrench, Phillips Screw-

driver, Pipe Tape or Pipe Thread Compound, and Supply

Lines

Installations may vary depending on how the previous faucet

was installed. Supplies necessary for the installation of the

faucet are not all included; however, they are available

wherever plumbing supplies are sold.

Prior to beginning installation, turn off the hot or cold water

lines, then turn on the old faucet to release built-up pressure.

When installing the new faucet, hand tighten the connector

nuts. DO NOT OVERTIGHTEN. Connections that are too

tight will reduce the integrity of the system.

MODEL #3210-150-CH-B-Z

B C

Summary of content (8 pages)

PAGE 1
MODEL #3210-150-CH-B-Z BASIN FAUCET Español p. 5 PACKAGE AND HARDWARE CONTENTS PART DESCRIPTION QUANTITY A Faucet 1 B Hot index button 1 C Cold index button 1 AA Mounting nut 1 B A C AA SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product.
PAGE 2
PRODUCT SPECIFICATIONS SPECIFICATIONS SPECIFICATIONS Max. flow rate: 2.2 GPM (8.5 LPM) at 60 PSI Brass waterways ASME A112.18.1/CSA B125 NSF 61-9 Manufactured to include no more than 0.25% weighted average lead content on wetted surfaces Ceramic cartridge Total weight of item: 1.056 lbs. ASSEMBLY INSTRUCTIONS 1. T urn off water at the supply valve under the sink or at the main water supply, disconnect the supply line, and remove old faucet. 5. Reconnect the water supply line.
PAGE 3
ASSEMBLY INSTRUCTIONS 8. Important: After installation is completed, remove aerator. Turn on water supply and allow both hot and cold water to run for at least one minute each. While water is running, check for leaks. Replace aerator. Tighten nuts slightly to stop minor leaks. If problems persist, refer to troubleshooting chart. 8 OPERATION INSTRUCTIONS This faucet is a single temperature faucet. Depending on what you hooked the faucet to, it will either be all COLD or all HOT water.
PAGE 4
PARTS LIST For replacement parts, call our customer service department at 1-877-319-3757, 7 a.m. - 5 p.m., CST, Monday - Friday.
PAGE 5
MODELO #3210-150-CH-B-Z CUENCA DEL GRIFO CONTENIDO DEL PAQUETE PIEZA DESCRIPCIÓN CANTIDAD A Grifo 1 B Botón de índice de calor 1 C Botón de índice en frío 1 AA Tuerca de montaje 1 B A C AA INFORMACIÓN DE SEGURIDAD Lea y comprenda completamente este manual antes de intentar ensamblar, usar o instalar el producto. PRECAUCIÓN • Si suelda las juntas durante la instalación del grifo, se deben retirar los asientos, los cartuchos y las arande las antes de usar la llama.
PAGE 6
ESPECIFICACIONES DEL PRODUCTO ESPECIFICACIONES ESPECIFICACIONES Caudal de flujo máximo: 8,3 LPM (2,2 GPM) a 60 PSI Cursos de agua de latón ASME A112.18.1/CSA B125 NSF 61-9 Fabricado para que no incluya más de 0,25% de contenido promedio en peso de plomo para superficies con agua Cartucho cerámico Peso total del artículo: 0,479 kg INSTRUCCIONES DE ENSAMBLAJE 1.
PAGE 7
ASSEMBLY INSTRUCTIONS 8. Importante: La instalación se ha completado Después, aireador removedor. Abra el suministro de agua y deje que caliente y agua fría para una duración de al menos un minuto cada uno. Mientras el agua corre, revise si hay fugas. Vuelva a colocar el aireador. Apretar las tuercas ligeramente para detener las fugas menores. Si el problema persiste, consulte la tabla de solución de problemas. 8 INSTRUCCIONES DE FUNCIONAMIENTO Este grifo es un grifo de una sola temperatura.
PAGE 8
LISTA DE PIEZAS Para piezas de repuesto, llame a nuestro departamento de servicio al cliente al 1-877-319-3757, de 7 am - 5 pm, hora central, Lunes - Viernes.