Instructions / Assembly

ManualsBrandsHOMEWERKS ManualsPlumbingUtility Shower Kit - WaterSense - 1.8 GPM

Indoor/Outdoor

Utility Shower Kit

03-20-2020

PACKAGE AND HARDWARE CONTENTS

MODEL

3070-250-CH-B-WS - Chrome

Showerhead ow rate in this unit meets Government standards of

A112.18.1M – 1.8 GPM (6.8 LPM) max at 80 PSI

Homewerks Worldwide, LLC • Lake Bluff, IL 60044 • www.HomewerksWW.com

PREPARATION

SAFETY INFORMATION

Before beginning assembly of product, make sure all parts are present.

Compare parts with package and hardware contents list. If any part is

missing or damaged, do not attempt to assemble the product. Contact

customer service for replacement parts.

Estimated Assembly Time: 30 minutes

Tools Required for Assembly (not included): Adjustable Wrench, Slip

Joint Pliers, Pipe Wrench, Phillips Screwdriver, Thread Seal Tape or Pipe

Thread Compound, and Supply Lines.

Installation may vary depending on how the previous shower was

installed. Supplies necessary for the installation of the shower are not

all included; however, they are available wherever plumbing supplies

are sold.

Prior to beginning installation, turn off the hot and cold water lines, then

turn on the old shower to release built-up pressure. When installing the

new faucet, hand tighten the connector nuts. DO NOT OVERTIGHTEN.

Connections that are too tight will reduce the integrity of the system.

Please read and understand this entire manual before attempting to

assemble, operate or install the product.

WARNING

• Protect your eyes with safety glasses when cutting or soldering water

supply lines.

CAUTION

• If you solder the joints during installation of the shower, the seats,

cartridges, and washers must be removed before using a ame

or the warranty will be voided on these parts.

• Cover the sink drain to avoid losing parts.

PART DESCRIPTION QUANTITY

A Showerhead 1

B Shower arm 1

C Soap dish 1

D Mounting screws 2

E Faucet body 1

Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-877-319-3757,

7:30 a.m. - 4:30 p.m., CST, Monday - Friday.

Summary of content (8 pages)

PAGE 1
Indoor/Outdoor Utility Shower Kit MODEL 3070-250-CH-B-WS - Chrome Showerhead flow rate in this unit meets Government standards of A112.18.1M – 1.8 GPM (6.8 LPM) max at 80 PSI PACKAGE AND HARDWARE CONTENTS PART DESCRIPTION QUANTITY A Showerhead 1 B Shower arm 1 C Soap dish 1 D Mounting screws 2 E Faucet body 1 B A D C E SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product.
PAGE 2
PRODUCT SPECIFICATIONS Maximum Flow Rate: 1.8 GPM (6.8 LPM) at 80 PSI Chrome finish Total weight of item: 1.706 lbs. A112.18.1M – 1.8 GPM (6.8 LPM) max at 80 PSI ASSEMBLY INSTRUCTIONS 1. T urn off water at the supply valve or at the main supply. Disconnect the supply lines to the faucet and remove the old faucet. 6. Using 1/2 inch male adapters, attach the hot and cold water supply lines.
PAGE 3
OPERATING INSTRUCTIONS The handles control the flow of hot and cold water to the faucet. Turn the right handle for cold water. Turn the left handle for hot water. Rotating the handles causes water to flow from the showerhead. The degree of handle rotation determines the volume of water flow. Returning the handles to the original position stops the flow of water. Turn off the water supply to the shower when not in use.
PAGE 4
ROUGH-IN 8.65" 21.54" 16.28" 7.48" 1/2"-14NPT 1.87" REPLACEMENT PARTS For replacement parts, call our customer service department at 1-877-319-3757, 7:30 a.m. - 4:30 p.m., CST, Monday - Friday.
PAGE 5
Kit utilitario de ducha interior / exterior MODELO 3070-250-CH-B-WS - Cromo El caudal del cabezal de ducha en esta unidad cumple con los estándares gubernamentales A112.18.1M - 1.8 GPM (6.8 LPM) máx.
PAGE 6
ESPECIFICACIONES DEL PRODUCTO Max. Caudal: 1,8 GPM (6,8 LPM) a 80 PSI Cromado El peso total del material: 1,706 libras. La tasa de flujo del cabezal de ducha en esta unidad cumple con los estándares del gobierno de A112.18.1M - 1.8 GPM (6.8 LPM) máximo a 80 PSI INSTRUCCIONES DE MONTAJE 1. C ierre la llave de paso de agua. Desconecte los tubos de suministro al grifo y retire el grifo viejo. 6. Usando adaptadores macho de 1/2 pulg., conecte las salidas de agua fría y caliente.
PAGE 7
INSTRUCCIONES DE FUNCIONAMIENTO Las manijas controlan el flujo de agua fría y caliente al grifo. Gire la manija derecha para agua fría, y la manija izquierda para agua caliente. Al girar las manijas, el agua fluye desde el cabezal de la ducha. El grado de rotación de la manija determina el volumen del flujo de agua. Devolver las manijas a la posición original detiene el flujo de agua. Cierre el suministro de agua a la ducha cuando no esté en uso.
PAGE 8
PREPARACIÓN EN 8.65" 21.54" 16.28" 7.48" 1/2"-14NPT 1.87" PIEZAS DE REPUESTO Para piezas de repuesto, llame a nuestro departamento de servicio al cliente al 1-877-319-3757, 08 a.m.-5 p.m. CST, Lunes - Viernes.