U S E R’S M A N J20H058 USB2.
Contents SECTION ONE: INTRODUCTION ............................................................................................ 3 1.INTRODUCTION ................................................................................................................................ 3 1.1 SCOPE ........................................................................................................................................... 3 1.2 FUNCTION .....................................................................
HON HAI PRECISION IND. CO., LTD. Section one: Introduction 1.Introduction Project Name: 802.11b/g/n (1x1) card based on IC Realtek RTL8188(CTV) with QFN package. 802.11b/g/n module provides wireless modem functionality utilizing direct sequence spread spectrum and OFDM/CCK technology. The typical use model for this embedded device is to allow the host device to be connected to an 802.11b/g/n 1x1 wireless network with infrastructure mode or to serve as an ad-hoc (peer-to-peer) data path. 1.
HON HAI PRECISION IND. CO., LTD. 2.Product Specification 2.1 Hardware Specification Wireless LAN Standards IEEE802.11b/g/n compatible ARIB STD-T66 compatible ETSI 300.328 compatible FCC 15.247 compatible FCC 15.407 compatible Operating Frequency Channel Numbers 2.400~2.4835GHz 1~11 channels active 12,13 channels passive 14 channels no need 802.11g: 54Mbps with fall back of 48, 36, 24, 18, 12, 9, 6Mbps. 802.11b: 11Mbps with fall back rates of 5.5, 2, and 1Mbps 11n: 6.5, 13, 19.5, 26, 39, 52, 58.
HON HAI PRECISION IND. CO., LTD. 3. Product Requirements 3.1 Hardware Requirements Host Interface PCB Antenna port: USB 2.0 2-layer FR4 ANT1 for TX/RX , ANT2 for RX Diversity 3.2 Hardware Architecture This specification describes an embedded 802.11b/g/n WiFi interface PCA ‘module’ for embedded device products. The module has two on-board connector. This module is powered from the host (5.0V) and interfaces to the host with USB 2.0 signals.
HON HAI PRECISION IND. CO., LTD. Section Two: Windows XP Wireless Utility and install 1. Open your Install Programs files folder or InstallCD and double Clicked the file named“setup.exe”. 2.
HON HAI PRECISION IND. CO., LTD. 3.
HON HAI PRECISION IND. CO., LTD. 4. In the next interface you can select the setup type that best suits your needs 5. You will see next two interfaces and they will direct you to select the the destination location. 6. you can see this interface and the note will tell you how to select in the second interface.
HON HAI PRECISION IND. CO., LTD. 7. The program will reboot the system before working, and click“ yes” 8. Install driver now 9.
HON HAI PRECISION IND. CO., LTD.
HON HAI PRECISION IND. CO., LTD. 4.FCC Notice: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
HON HAI PRECISION IND. CO., LTD. This device is intended only for OEM integrators under the following conditions: 1) 2) The antenna must be installed such that 20 cm is maintained between the antenna and users, and The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required.
HON HAI PRECISION IND. CO., LTD. 5.Canada Notice This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence.
HON HAI PRECISION IND. CO., LTD. This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required.
HON HAI PRECISION IND. CO., LTD. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains IC: 2878D-J20H058”.
