T77H519 NFC Module USER MANUAL Project Name Revision Foxconn project code NFC module 00 T77H519 1
Contents 1. INTRODUCTION .......................................................................... 錯誤! 尚未定義書籤。 2. HARDWARE SPECIFICATION .................................................................................... 6 3. PRODUCT REQUIREMENTS ...................................................................................... 6 4. INTERFACE OF CONNECTOR OF NFC MODULE .................................................... 7 5. ANTENNA CONNECTOR OF NFC MODULE....................................
1. Introduction The T77H519 NFC module provides contactless payment, contactless ticketing, service discovery, exchange information etc. This module is based on Broadcom BCM20792M solution, which is integrated NFC subsystem, interfaces, and microprocessor and memory unit. 1.1 Scope The NFC module supports for the ISO/IEC 18092, ISO/IEC 21481, ISO/IEC 14443 Types A, B and B’, Japanese industrial standard (JIS)(X) 6319-4, and ISO/IEC 15693 standards. 1.
1.3 Electrical Characteristics Parameter Frequency Range VBAT VDD I/O Input Supply UICC (class C) Voltage UICC (class B) Reader mode Writer mode Peer to peer communication Power Polling mode consumption Target mode Sleep mode Snooze standby mode Communication distance Peer to Peer Communication Speed Minimum 2.8 1.62 1.78 2.9 - Typical 13.56 3.3 1.8 1.88 3.1 - Maximum 5.5 3.6 1.98 3.3 247 247 Units MHz V V V V mA mA - - 247 mA - 4.1 - 14 7.
1.4 BSC (I2C -compatible) Characteristics 2 Following are the main features of NFC module I C interface • Slave mode • Low-speed mode (100kbps), fast mode (400kbps), and high-speed mode (3.4Mbps) • 7-bit or 10-bit addressing mode, default boot-up of fixed 7-bit address (0x77), thereafter configurable to 7-bit or 10-bit addresses • Dedicated TX and RX FIFOs, 272 bytes each. BSC Timing waveform I2C _REQ is an output signal from the module to the host that it wishes to communicate.
2. Hardware Specification 2.1 Antenna Electrical Specification Parameter Typical Units Operating frequency range 13.56 MHz Communication distance > 20 mm 3. Product Requirements 3.1 Hardware Requirements of NFC module Form factor Host Interface PCB 15 mm x15mm module with 11-pin FPC connector BSC (I2C -compatible) interface 4-layer design 3.
4. Interface of Connector of NFC module Manufacturer: JST Manufacturer Part number: 11FHSY-RSM1-GAN-TB(HF) Pin 1 Pin 1 Pin definition Pin Symbol VBAT 1 VDDIO 2 2 I C -SDA 3 I2C -SCL 4 GND 5 IRQ-NFC 6 7 NFC_PRESENCE REG_UP 8 I/O I I I/O I G O G I 9 VDD_Ext_SE O 10 11 S1 S2 UIM_PWR SWP GND GND I I/O G G Note Power supply from battery (2.8V - 5.5V) Power supply to I/O (1.62V – 3.
5.
6. Test Operating Instructions Info Please refer to another file named “Test SOP for T77H519 NFC series projects”.
COMPANY CONFIDENTIAL Industry Canada statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence.
COMPANY CONFIDENTIAL IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization.
COMPANY CONFIDENTIAL Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
COMPANY CONFIDENTIAL additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product.
