User Manual

Drawers feature a welded construction with high drawer
sides, which accept hanging file folders without the need
for hangrails. Sides are welded to drawer front, the
bottom and the back. Drawer front includes a
polypropylene plastic filler enclosing the thumb latch
mechanism.
Drawer Function:
Drawers operate on three-part telescoping ball bearing
slides with 100% drawer extension.
Hardware:
Includes a bright aluminum drawer pull, thumb latch
button and label holder on each drawer front. Drawer pull
is 1-1/8” deep x 4-1/4” wide, attached at a 4” span. The
thumb latch is spring operated, and prevents drawers
from opening without activating the mechanism to release
the drawer. Label holder measures 3-7/16” W x 2” H
overall, with a viewable area of 2-3/4” W x 1-1/4” H.
Locking:
The included core removable lock is located in the right
front corner of the top. The lock utilizes a lock link which
activates a one piece lock bar, engaging all drawers on
the right side. HON “One Key” interchangeable cores may
be ordered separately to key units alike.
Follower Block:
Positive locking follower with a spring loaded release
latch, adjustable in 5/8” increments. Block is constructed
of steel with two vertical ribs and a horizontal channel for
added strength. Side arm guides are constructed of steel.
Follower is either color matched to case, or is constructed
of a pre-painted steel in the color of gray.
KEY DIMENSIONS
•Heights:
2 drawer – 29”
4 drawer – 52”
5 drawer – 60”
•Width:
Letter – 15”
Legal – 18-1/4”
•Depth: 26-1/2”
Filing Capacity:
25” per drawer front to back filing
310 Vertical Files
Technical Specifications
Features:
310 Series Vertical Files are available in a 2, 4 or 5
drawer configuration, in letter or legal width, and these
cabinets are 26-1/2” deep. The five drawer unit uses
slightly shorter drawer fronts, horizontal crossbars and
kickplate to accommodate access to the top drawer.
Construction:
The case top has welded seams on the front corners and
is welded to the back and sides. Vertical reinforcing
channels are formed to add strength and welded to sides,
two at the front and two at the rear. Formed horizontal
crossbar dividers are welded in place to each side,
between drawers. The single piece kickplate/corner
gusset is secured to sides by welds and structural
adhesive. A bottom rear reinforcing channel is welded to
the back and to the sides. Both the kickplate and rear
reinforcing channel wrap under the case for a sturdy
construction.
54-5027 Rev. A
7/5/2011
Page 1
QUICK REFERENCE TABLE - Actual Dim ens ions
Models H312 H312C H314 H314C H315 H315C
Case Height 29" 29" 52" 52" 60" 60"
Case Width 14.9" 18.2" 14.9" 18.2" 14.9" 18.2"
Case Depth 26.6" 26.6" 26.6" 26.6" 26.6" 26.6"
Top Height 1.25" 1.25" 1.25" 1.25" 1.25" 1.25"
Draw er Front Height 11.4" 11.4" 11.4" 11.4" 11" 11"
Draw er Front Width 13.3" 16.6" 13.3" 16.6" 13.3" 16.6"
Draw er Divider Height .5" .5" .5" .5" .25" .25"
Kickplate Height 4.1" 4.1" 3.3" 3.3" 2.5" 2.5"
INSIDE DRAWER
Height 10.7" 10.7" 10.7" 10.7" 10.3" 10.3"
Depth 25.5" 25.5" 25.5" 25.5" 25.5" 25.5"
Width 11.9" 14.9" 11.9" 14.9" 11.9" 14.9"
Load Capacity/draw er 57 lbs 71 lbs 57 lbs 71 lbs 57 lbs 71 lbs
The HON Company
200 Oak Street
Muscatine, IA 52761
800-833-3964
hon.com