www.collegehillshonda.com/parts Accessory INSTALLATION INSTRUCTIONS Application Publications No. AII 25886 XM RADIO SYSTEM The XM Radio system will not fit in a vehicle equipped with a navigation system or a rear entertainment system.
XM Antenna Kit (sold separately): P/N 08A15-1E1-100 Antenna Base Kit (sold separately): P/N 08A15-1E1-000 Display module TOOL AND SUPPLIES REQUIRED #2 Phillips screwdriver Flat-tip screwdriver Utility knife Diagonal cutters Push pin Tape measure Shop towel Scissors Ratchet 8 mm, 10 mm, and 14 mm Sockets 8 mm, 10 mm, and 14 mm Combination wrenches Felt-tip pen Isopropyl alcohol Drill 3 mm and 10 mm drill bits Eye protection (face shield, safety goggles, etc.
Illustration of an Installed XM Radio System INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” ANTENNA FM MODULATOR UNIT 1. Make sure you have the anti-theft code for the radio, then write down the frequencies for the preset buttons. 2.
. Remove the four screws that fasten the audio bracket. Pull the audio unit out toward you, and unplug the vehicle connector and antenna cable from the rear of the audio unit. If equipped with a cassette/in-dash CD changer, unplug the additional connectors. VEHICLE CONNECTOR (If equipped, unplug the additional connectors.) AUDIO UNIT 6. Remove the center panel (four self-tapping screws and two clips, and unplug the vehicle accessory power outlet).
8. Remove the four screws that fasten the left and right vehicle bracket. Pull the heater control unit and pocket toward you, and unplug the vehicle connectors. 10. Slide the clip nut onto the display module pocket flange. DISPLAY MODULE POCKET FLANGE VEHICLE CONNECTOR HEATER CONTROL UNIT CLIP NUT LEFT VEHICLE BRACKET Clean with isopropyl alcohol. DISPLAY MODULE POCKET SCREW 9.
14. Fit the DIN bezel around the display module pocket. Set the heater control unit on the display module pocket, and reinstall the left and right vehicle brackets using the two self-tapping screws removed in step 9. Attach the display module to brackets with three self-tapping screws supplied with the XM radio attachment kit. SELFTAPPING SCREW (Reuse.) LEFT VEHICLE BRACKET 16. Remove the driver's seat rear cover (four clips). Take care not to damage the clips.
18. On the driver’s side of the vehicle, remove the center console lower cover (gently pull the cover out toward you to release the seven clips). Take care not to damage the clips. 20. Route the XM radio harness and two subantenna cables from the dashboard opening to driver’s floor. Using one cushion tape, attach it to the vehicle frame. DRIVER’S SEAT DASHBOARD OPENING Align. CUSHION TAPE 50 mm DRIVER’S CENTER CONSOLE LOWER COVER CLIPS (7) 19.
22. Plug the audio unit vehicle 20-pin connector into the XM radio 20-pin connector that is blue-taped to the XM radio harness. Wrap one EPT sealer around the subantenna cable in the area shown. SUBANTENNA CABLE 25. Place the display module/heater control unit assembly near the dashboard opening, and route the display module cable along the XM radio harness and the subantenna cables. VEHICLE FRAME (Clean with isopropy alcohol.
28. Plug the XM radio harness 20-pin connector and sub antenna cable into the audio unit, and carefully slide the audio unit into the dashboard. Reinstall the four audio unit screws. XM RADIO HARNESS 20-PIN CONNECTOR 30. Continue routing cables through the center console and toward the rear of the vehicle. Using scissors, cut one cushion tape in half. Clean the vehicle frame with isopropyl alcohol, and attach half of the cushion tape to the vehicle frame in the area shown.
33. Measure and slit the driver’s floor carpet in the area shown. Be careful not to damage the subantenna cables and XM radio harness when cutting the floor carpet. Installing the Antenna 35. On the driver's side of the vehicle, remove the weatherstrip from the left front door opening in the area shown, then remove the left front "A" pillar trim (two clips). FLOOR CARPET CLIPS (2) slit 50 mm WEATHERSTRIP WIRE TIE LEFT FRONT "A" PILLAR TRIM DISPLAY MODULE CABLE SUBANTENNA CABLE XM RADIO HARNESS 36.
37. Remove the fuel lid door opener lever, then remove the left front door sill trim (three clips and two retaining tabs). 39. Get two EPT sealers. Using scissors, cut two EPT sealers into six pieces. Wrap the them around the antenna unit cable at the measurements shown. ANTENNA UNIT RETAINING TAB 60 mm FUEL LID DOOR OPENER LEVER 60 mm 60 mm 60 mm 200 mm 60 mm LEFT FRONT DOOR SILL TRIM ADHESIVE BACKING (Remove.) 60 x 60 mm DOUBLE-SIDED ADHESIVE TAPE EPT SEALER CLIP CLIPS (2) Cut. 40.
43. Route the antenna unit cable along the front windshield and the top of the dashboard. Insert the antenna unit cable with the EPT seals between the windshield and the dashboard. ANTENNA UNIT CABLE Insert. 45. Secure the antenna unit cable to the vehicle harness with two wire ties. ANTENNA UNIT CABLE VIN IDENTIFICATION PLATE (Don’t hide the VIN number with the antenna unit cable.) VEHICLE HARNESS FRONT WINDOW GLASS ANTENNA UNIT CABLE Insert. WIRE TIES Route under the dashboard. DASHBOARD 44.
47. Continue routing the antenna unit cable alongside the vehicle harness, and out through the hole in the floor carpet under the driver's seat. Secure the antenna unit cable to the vehicle harness with four wire ties in the area shown. FLOOR CARPET 50. Get the DIN cable. Plug the DIN cable into the FM modulator unit and the receiver unit. FM MODULATOR UNIT RECEIVER UNIT ANTENNA UNIT CABLE HOLE UNIT BRACKET 51. Position the unit assembly under the driver’s seat.
53. Get the five wire ties with clips and two wire ties. Secure all of the cablse to the unit bracket in the order shown: XM radio harness, subantenna cables, and the display module cable. 55. Slide the driver's seat forward, and install the unit bracket to the driver’s seat rails using four 6 x 12 mm washer-bolts. Tighten the bolts securely. DRIVER’S SEAT UNIT BRACKET XM radio harness, subantenna cables, and the display module cable.
