www.collegehillshonda.com/parts INSTALLATION INSTRUCTIONS Accessory Application CD CHANGER ATTACHMENT KIT 2002-2005 CIVIC SI Publications No.
6-Disc CD Changer (sold separately): P/N 08A26-1B1-100 Illustration of the CD Changer Installed in the Vehicle CD changer BUS CABLE CD CHANGER 4 Washer-screws, 4 x 6 mm (Not used) Adhesive seal sheet Cover plates AUDIO UNIT L R INSTALLATION CD magazine Owner’s Manual TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Flat-tip screwdriver Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and
4. Remove the driver's dashboard lower cover. Turn the lock knob 90° counterclockwise. Gently pull down on the left side of the cover to release the two hooks, then pull down on the cover to release the three retaining tabs. Take care not to damage the retaining tabs. 6. Remove the shift lever trim: • Pull the shift boot down, and remove the shift knob by turning it counterclockwise. • Reach through the shift boot, and gently pull out on the shift lever trim to release the bottom of the trim.
7. Remove the vehicle harness clip from the center panel bracket by pushing up on the locking tab on the clip and pulling the clip out toward you. 9. Remove the dashboard center lower cover, and disconnect the accessory power socket connector. Remove the two self-tapping screws from the back of the front center console. SELF-TAPPING SCREW CENTER PANEL BRACKET Push on the locking tab. CLIP 8. VEHICLE HARNESS Reach through the glove box area, and loosen the bolt that secures the center panel.
11. Remove the front center console: 13. Turn over the cargo area mat, and remove the cargo area floor. • Slide the front seat completely rearward. • Open the lid, and take out the console box mat. • Remove the two bolts from the inside of the pocket. • Remove the two clips, then slide the front center console to the rear to release the four retaining tabs. Take care not to damage the retaining tabs. CARGO AREA MAT CARGO AREA FLOOR CONSOLE BOX MAT CLIP BOLT RETAINING TAB 14.
15. Remove the rear seat cushion bolt, and remove the rear seat cushion by lifting the rear of the cushion to release the hooks and then pulling it toward you. 20. Remove the left rear seat-back center hinge (one bolt). LEFT REAR SEAT-BACK CLIP FLOOR CARPET SEATBACK CENTER HINGE REAR SEAT CUSHION LEFT REAR SIDE PANEL TRIM 2 1 CLIP LEFT PIN BOLT 22 N·m (16 lb-ft) HOOK BOLT 21. Remove the clip from the floor panel behind the seat-back. HOOK 16. Remove the clip that secures the floor carpet. 17.
24. Remove the left rear bulkhead cover: 26. Remove the left rear seat belt lower anchor bolt. • Remove the clip from the left rear bulkhead cover. Take care not to damage the clip. 27. Remove the rear trim panel (three clips and two hooks). • Gently pry the left rear bulkhead cover away from the left rear side trim panel by inserting the end of a flat-tip screwdriver wrapped in a shop towel into the groove of the left rear bulkhead cover.
30. Get template A from the kit. Tape the template to the left rear side trim panel in the area shown, and tape it in place using strips of masking tape. Using a pushpin, mark the trim panel at each of the five marked points on the template. Remove template A. 33. Position template B on the air outlet area of the left rear side trim panel, and tape it in place using strips of masking tape. Using a pushpin, mark the trim panel at each of the four marked points on the template. Remove template B.
35. Slide the four 6 mm clip nuts onto the left rear side trim panel through the 10 mm holes you just made. 38. Insert the studs of the two CD changer plates into the 7.5 mm holes (made in step 31) from the back. CD CHANGER BRACKET 6 mm CAP NUT 6 mm CLIP NUT LEFT REAR SIDE TRIM PANEL (AIR OUTLET AREA) 6 mm STEPPED BOLT 6 mm CAP NUT CD CHANGER PLATE 39. Insert the studs of the CD changer plate into the holes in the CD changer bracket, and install a 6 mm cap nut on the end of each stud.
42. Visually check the position of the spring adjusting pins on both sides of the CD changer. If both of the spring adjusting pins are not in the horizontal (H) position, move the pins to the horizontal (H) position by sliding them up with an awl. 45. Secure the CD changer bus cable connector to the CD changer with the remaining 3/4 piece of the EPT seal cut in step 36.
Routing the Bus Cable 48. From the back of the left rear side trim panel, route the bus cable as shown. Secure the bus cable to the fuel fill door opener cable with two wire ties in the areas shown. Do not secure the bus cable to the clear washer tube. 50. Route the bus cable from the side panel to the center of the floor panel along the floor cross member as shown. CUSHION TAPE BUS CABLE WIRE TIE Do not secure the bus cable to the clear washer tube.
53. Route the bus cable so that its connector is about 50 mm farther than the vehicle 20-pin connector. Secure the bus cable to the vehicle harness with two wires in the areas shown. 55. Near the parking brake lever, secure the bus cable to the vehicle harness with three wire ties in the areas shown. WIRE TIE BUS CABLE BUS CABLE CONNECTOR VEHICLE HARNESS VEHICLE 20-PIN CONNECTOR WIRE TIE About 50 mm 54. Secure the bus cable to the vehicle harness with two wire ties in the areas shown. 56.
Installing the Center Panel/Radio Unit 57. Check that the vehicle harnesses are not pinched by the stays. 58. While holding the center panel with the radio unit installed near the center panel opening, plug the vehicle 20-pin connector, the antenna lead, the heater control harness connector, and the bus cable connector into the rear of the radio unit. VEHICLE HARNESS ANTENNA LEAD CENTER PANEL STAY STAY VEHICLE CONNECTOR BOLT (Tighten after installing the center panel.
60. Check that all wire harnesses are routed properly and all connectors are plugged in. 61. Reconnect the negative cable to the battery, and set the clock. 62. Enter the customer’s radio anti-theft code, and reset the radio station presets. 63. Check the operation of the CD changer according to the Owner’s Manual. 64. Put the CD changer Owner’s Manual and the shipping clips retained in step 41 in the glove box. 65. Reinstall all removed parts. 66.