www.collegehillshonda.com Accessory INSTALLATION INSTRUCTIONS PARTS LIST Application Publications No. AII 38137-38714 Accessory HandsFreeLink 2008 ODYSSEY Issue Date JAN 2008 Fuse label HFL Attachment Kit P/N 08E02-SHJ-100B HFL trim Fuse (2 A) HFL bracket 6 EPT sealers HFL harness 8 Wire ties HFL subharness 4 Self-tapping screw, 3 x 10 mm 2 Washer screws, 4 x 12 mm 2 Double-faced tapes Self-tapping screw HFL retainer Bush Ground bolt Template Rubber bumper © 2008 American Honda Motor Co.
www.collegehillshonda.com HFL Blue Tooth Kit P/N 08E00-E10-100 Illustration of the HFL Installed on the Vehicle Switch SWITCH CONTOROL UNIT HFL HARNESS Control unit FUSE (2 A) Accessory User's Information Manual HFL SUBHARNESS 7518071E INSTALLATION TOOL AND SUPPLIES REQUIRED #2 Phillips screwdriver 10 mm Combination wrench 10 mm and 14 mm Socket Pushpin Ratchet 3 mm, 4.5 mm, 6 mm, 9 mm, and 10 mm Drill bit Eye protection (face shield, safety goggles, etc.
www.collegehillshonda.com 3. Disengage eight retaining tabs and remove left and right lens from the roof console. 7. Using a flat-tip screwdriver, push the hook and turn the holder. Remove the holder. PLASTIC TRIM TOOL VEHICLE CONNECTORS SUNVISOR HOLDER VEHICLE CONNECTOR ROOF CONSOLE SUNGLASS HOLDER (Open.) COVER RIGHT LENS LEFT SUNVISOR RETAINING TAB 2 SCREWS 4 RETAINING TABS 2 BOLTS 4 RETAINING TABS 8. Disengage two screws and remove the left sunvisor. 9.
www.collegehillshonda.com 10. Remove the left front door sill trim (three clips). LEFT FRONT DOOR SILL TRIM 12. Attach the fuse label (2 A) to the fuse case of the HFL subharness. 3 CLIPS FUSE LABEL (2 A) HFL SUBHARNESS FUSE CASE HFL SUBHARNESS 7821100B 4301210B 11. Pull away the weatherstrip from the left kick panel. Remove the left kick panel (three clips). WEATHERSTRIP 13. Plug the HFL subharness 6-pin connector into the 6-pin opening in the fuse box.
www.collegehillshonda.com NOTE: If another accessory is already plugged into the 6-pin connector, remove the dummy connector from the 6-pin connector taped to the HFL subharness. Plug the 6-pin connector from the other accessory harness into the 6-pin connector from the HFL subharness you just unplugged and plug the HFL subharness into the fuse box. 16. Remove the vehicle bolt (discard) and install the ground bolt with HFL subharness ground terminal as shown.
www.collegehillshonda.com 23. Cut the template into template A and template B. 20. Secure the HFL subharness to the vehicle harness with a wire tie. VEHICLE PANEL EPT SEALER TEMPLATE A TEMPLATE WIRE TIE HFL SUBHARNESS TEMPLATE B 7517091E 24. Remove the damper (two tapping screws). VEHICLE HARNESS 7517061E SUNGLASSES HOLDER 21. Using isopropyl alcohol on a shop towel, clean the area where the EPT sealer will attach. Attach a EPT sealer to secure the HFL subharness to the vehicle panel.
www.collegehillshonda.com 27. Remove the console light from the roof console (four retaining tabs). 29. Attach masking tape to the roof console as shown. ROOF CONSOLE MASKING TAPE ROOF CONSOLE 4 RETAINING TABS 7716020X CONSOLE LIGHT 7523030E 30. Attach template A with masking tape to the roof console at the indicated position. ROOF CONSOLE PUSHPIN 28. Enlarge the hole on the roof console with 9 mm drill bit.
www.collegehillshonda.com 34. Drill 4.5 mm holes at the two locations marked on the roof console in step 32. After drilling, remove any burrs. 39. Drill a 3 mm hole at the four locations marked on the roof console in step 36. 19 mm HOLE SAW DRILL BIT (4.5 mm) DRILL BIT (3 mm) ROOF CONSOLE ROOF CONSOLE 4 MARKS DRILL BIT (3 mm 6 mm 10 mm) 2 MARKS 7517120E DRILL 35. Attach template B with masking tape on the roof console at the indicated position. 7517141E PUSHPIN 4 MARKS 41.
www.collegehillshonda.com 42. Using a utility knife, cut along the marking made on the roof console in step 37. After cutting, remove any burrs. ROOF CONSOLE 45. Connect the HFL harness 22-pin connector to the control unit. CENTER CONTROL UNIT UTILITY KNIFE Mark made in step 37. CONTROL UNIT Cut out. HFL HARNESS ROOF CONSOLE Remove the adhesive backing. Cut out. ROOF CONSOLE HFL HARNESS 22-PIN CONNECTOR ROOF CONSOLE 7517171E 7517152E 43. Remove the masking tape attached in step 29. 44.
www.collegehillshonda.com 51. Connect the HFL harness 20-pin connector to the switch. 48. Bend the switch terminal as shown. BACKSIDE OF THE SWITCH SWITCH TERMINAL (Bend.) SELF- TAPPING SCREW (Reuse.) SPEAKER SWITCH SWITCH TERMINAL HFL TRIM VEHICLE BUSHES (Reuse.) SWITCH HFL RETAINER HFL HARNESS 20 -PIN CONNECTOR BUSHES ROOF CONSOLE SELF- TAPPING SCREW 7517192E 52.
www.collegehillshonda.com 55. Hold the roof console close to the roof console opening and connect the HFL harness 4-pin connector to the HFL subharness 4-pin connector. GREEN CONNECTOR 58. Connect the vehicle connectors to the roof console. Reinstall the roof console with the four bolts from step 5. VEHICLE CONNECTORS WIRE TIE VEHICLE BRACKET HFL SUBHARNESS 4-PIN CONNECTOR Vehicle front ROOF CONSOLE ROOF CONSOLE OPENING 7518042E HFL HARNESS 4-PIN CONNECTOR 2 BOLTS 2 BOLTS ROOF CONSOLE 59.
www.collegehillshonda.com 60. Attach the fuse label to the No. 33 slot on the fuse box cover. 61. Check that all wire harnesses are routed properly and that all connectors are plugged in. 62. Reinstall all removed parts. FUSE LABEL (OPITION FUSE 2 A) 63. Reconnect the negative cable to the battery. 64. Enter the customer’s radio anti-theft code, and reset the radio station presets. FUSE BOX COVER 65. Reset the clock. NOTE: When the battery is disconnected, the driver’s window AUTO function is disabled.