www.collegehillshonda.com Accessory INSTALLATION INSTRUCTIONS PARTS LIST Application 2008 ACCORD 2-DOOR BACK-UP SENSOR Publications No. AII 37561-38377 Issue Date NOV 2007 Control unit bracket (L4) Back-up Sensor Attachment Kit P/N 08V67-TE0-100A Control unit Control unit bracket (V6) Beeper 13 Wire ties 4 Sensor clips Wire tie with clip Back-up sensor harness Back-up sensor subharness 2 Wire ties with holder 2 Urethane tapes Fuse label © 2007 American Honda Motor Co., Inc.
www.collegehillshonda.com Flange bolt, 6 x 12 mm TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Flat-tip screwdriver Ratchet 8 mm and 10 mm Socket Flange nut Pushpin Drill 3 mm Drill bit 4 24 mm and 26 mm Hole saw Harness tapes Ruler Eye protection (safety goggles, face shield, etc.
www.collegehillshonda.com 2. Disconnect the negative cable from the battery. 5. 3. Remove the two covers from the rear bumper and remove the rear bumper (two bolts, six self-tapping screws, two clips, and unplug one connector). Remove the rear trim panel (five clips and three hooks). REAR TRIM PANEL 4 CLIPS NOTE: Have an assistant help you remove the rear bumper. CONNECTOR 2 BOLTS 3 HOOKS CLIP 6. 6 SELF-TAPPING SCREWS 2 COVERS 2 CLIPS 4.
www.collegehillshonda.com 8. Using the trim tool, remove the rear shelf access panel, then release the front rear speaker retaining tab. 10. Remove the left rear speaker (one bolt and disconnect the vehicle connector). BOLT LEFT REAR SPEAKER REAR SHELF ACCESS PANEL LEFT REAR SPEAKER COVER VEHICLE CONNECTOR TRIM TOOL (TN SILRIMTL10) 7115040E 11. Wrap urethane tape around the control unit at the area shown. Then, attach the control unit bracket into the control unit. L4 MODEL 9.
www.collegehillshonda.com L4 Model V6 MODEL 12. Install the control unit to the vehicle panel: • Partially thread the 6 mm flange nut onto the control unit bracket stud. Insert the control unit bracket stud into the hole in the vehicle panel. Tighten the 6 mm flange nut to secure the bracket to the vehicle panel. VEHICLE PANEL • Loosen the upper bolt from the relay support. Remove the relay support (one bolt and disconnect the vehicle connectors). BOLT (Loosen.
www.collegehillshonda.com 13. Attach the 2A fuse label to the fuse case on the back-up sensor harness. 14. Disconnect the back-up light 2-pin connector from the left taillight, and plug it into the back-up sensor harness 2-pin connector. Plug the remaining back-up sensor harness 2-pin connector into the left taillight.
www.collegehillshonda.com 15. At the left taillight, secure the back-up sensor harness to the vehicle harness with one wire tie. V6 MODEL VEHICLE HARNESS BACK-UP SENSOR HARNESS WIRE TIE VEHICLE HARNESS VEHICLE HARNESS BACK-UP SENSOR HARNESS GREEN TAPE 742314BE 16. Plug the back-up sensor harness 14-pin connector into the control unit, and route the harness forward along the vehicle harness. Secure the back-up sensor harness to the vehicle harness at the green tape.
www.collegehillshonda.com 17. Secure the back-up sensor harness to the vehicle harness with two additional wire ties at the locations shown. V6 MODEL VEHICLE HARNESS L4 Model 2 WIRE TIES 2 WIRE TIES VEHICLE HARNESS WIRE TIE WIRE TIE BACK-UP SENSOR HARNESS VEHICLE HARNESS BACK-UP SENSOR HARNESS VEHICLE HARNESS BACK-UP SENSOR HARNESS 742401CE BACK-UP SENSOR HARNESS 771103BB 18. Secure the back-up sensor harness clip to the hole in the vehicle panel.
www.collegehillshonda.com 19. Using scissors cut one urethane tape in half, and then cut one of the halves again. Wrap the cut pieces around the beeper harness shown. 23. Secure the beeper harness to the vehicle harness with one wire tie. 20. Install the connector clip to the beeper 2-pin connector. WIRE TIE VEHICLE HARNESS URETHANE TAPE BEEPER 2-PIN CONNECTOR BEEPER 2-PIN CONNECTOR CONNECTOR CLIP 2-PIN CONNECTOR (Wrap from the end of the 2-pin connector.
www.collegehillshonda.com 28. Install one wire tie with clip to the holder with the fuse case, and attach the wire tie to the vehicle harness. WIRE TIES WIRE TIE VEHICLE HARNESS WIRE TIE WITH CLIP VEHICLE HARNESS FUSE CASE BACK-UP SENSOR HARNESS VEHICLE GROMMET 761402AE 29. Remove the vehicle grommet from the rear panel. 30. Route the back-up sensor 6-pin connector through the hole in the rear panel, and seat the harness grommet in the rear panel hole.
www.collegehillshonda.com 32. Install one wire tie with holder to the back-up sensor harness 16-pin connector, and attach the wire tie to the vehicle harness. WIRE TIE WITH HOLDER NOTE: There are several markings on the inside of the rear bumper. Before piercing the rear bumper, verify you have the correct locations. BACK-UP SENSOR HARNESS 6-PIN CONNECTOR 3 MARKS 3 MARKS REAR BUMPER REAR BUMPER PUSHPIN VEHICLE HARNESS MARK REAR BUMPER PUSHPIN MARK 742603BE 742410BE 33.
www.collegehillshonda.com 34. While wearing eye protection drill the rear bumper: • NOTE: Center sensors are 26 mm holes, side sensors are 24 mm holes. • From the outside of the bumper, drill all eight pierced marks using a 3 mm drill bit. • Using a 24 mm hole saw, enlarge the lower outboard hole on the left side of the bumper. Remove all burrs. Using 26 mm holes saw, enlarge both lower in board bumper holes at the center of the bumper. Remove all burrs.
www.collegehillshonda.com 36. Install two center sensors into the 26 mm holes in the rear bumper using the sensor clips. Note the direction and location for each sensor. 2 BACK-UP SENSOR SUBHARNESS CLIPS SENSOR CLIP REAR BUMPER BACK-UP SENSOR SUBHARNESS SENSOR CLIP REAR BUMPER Outside Inside 2 CENTER SENSORS (Blue) 2 HOLES, 26 mm HOLDER CLIP WIRE TIE WITH CLIP 742413BE SENSOR CLIP 2 CENTER SENSORS (Blue) 37.
www.collegehillshonda.com 41. Using isopropyl alcohol on a shop towel, clean the area where the harness tapes will attach. BACK-UP SENSOR SUBHARNESS 6-PIN CONNECTOR BACK-UP SENSOR HARNESS 6-PIN CONNECTOR 4 GREEN TAPES BACK-UP SENSOR SUBHARNESS CORNER SENSOR 4 HARNESS TAPES LEFT CENTER SENSOR RIGHT CENTER SENSOR REAR BUMPER CORNER SENSOR 761302AE 771107BB 42. At each green tape location, attach the back-up sensor subharness to the rear bumper with four harness tapes. 43.
www.collegehillshonda.com 44. Check that all wire harnesses are routed properly and that all connectors are plugged in. 45. Reinstall all removed parts. 46. Reconnect the negative cable to the battery. 47. Enter the anti-theft codes for the radio and navigation systems (if equipped), then enter the customer’s radio presets. 48. Reset the clock. 49. Check that the back-up sensors work properly as described in the Accessory User’s Information Manual supplied.
