www.collegehillshonda.com/parts Accessory INSTALLATION INSTRUCTIONS PARTS LIST Security System (sold separately): P/N 08E51-S84-100 Application 2001 ACCORD 2- AND 4-DOOR (INCLUDES V6) SECURITY SYSTEM Publications No.
Wire tie with clip 9 Long wire ties Cushion tape Red connector clip TOOLS AND SUPPLIES REQUIRED Small flat-tip screwdriver #2 Phillips screwdriver Eye protection (face shield, safety goggles, etc.) Center punch Drill 5.
Adjusting the Control Unit • INSTALLATION Use a small flat-tip screwdriver to change the mode switch and the horn/siren switch and to adjust sensitivity. GLASS BREAKAGE SENSOR MODE SWITCH Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your car. These procedures should not be attempted by "do-it-yourselfers." 1.
5. Remove the left fuse box cover (three retaining clips and two tabs). 7. Remove the driver’s door sill molding (four clips). CLIP TAB CLIP DRIVER'S DOOR SILL MOLDING LEFT FUSE BOX COVER LEFT FUSE BOX TAB CLIP RETAINING CLIPS 6. Remove the driver's dashboard lower cover (three screws, and five retaining clips). 8. Remove the kick panel (two clips, and pull). SCREW KICK PANEL SCREW SCREW DRIVER'S DASHBOARD LOWER COVER CLIP 4 of 12 CLIP All 21624 (0008) © 2000 American Honda Motor Co.
9. Remove the right fuse box cover (three retaining clips and two tabs). 11. Open the glove box, and remove the two screw caps and seven self-tapping screws. Unplug the connector, and remove the glove box by pulling it toward you. GLOVE BOX TAB CLIP CONNECTOR SELF-TAPPING SCREW CAPS RIGHT FUSE BOX COVER RIGHT FUSE BOX TAB 12. Lower the steering wheel tilt lever. Remove the upper and lower steering column covers (three screws, six tabs, and one harness clip).
13. Measure and mark the upper steering column cover. 16. Locate the 2-pin connector included in the kit, and lower the lock. Firmly push the LED terminals into the 2-pin connector. Insert. 5.5 mm DRILL Lock. UPPER STEERING COLUMN COVER WHITE WIRE 20 mm RED WIRE 17. Measure and mark the driver's dashboard lower cover. (If necessary, remove the insulation.) MARK 14. While wearing eye protection, lightly center-punch the mark; then drill a 5.5 mm hole through the upper steering column cover.
19. Route the terminal ends of the disarm switch through the hole you just drilled, and secure it with the washer and 12 mm nut from the kit. NUT 21. Push the wire tie with clip into the hole in the back of the control unit bracket. Position the control unit bracket on the driver's dashboard lower cover, and install the three self-tapping screws from the attachment kit. SELF-TAPPING SCREW WASHER WIRE TIE WITH CLIP DRIVER'S DASHBOARD LOWER COVER CONTROL UNIT BRACKET DISARM SWITCH 20.
23. Secure the disarm switch wire harness to the disarm switch with one short wire tie, then attach the harness to the driver's dashboard lower cover with two halves of a cushion tape in the areas shown. (Cut a cushion tape in half with scissors, and use the two halves to secure the harness.) CONNECTOR CLIP 26. Attach the 14-pin connector of the security system wire harness to the side of the vehicle connector.
28. Remove the upper bolt that fastens the engine hood opener, and attach the ground terminal of the security system wire harness with the ground bolt from the kit. 31. Unplug the 20-pin connector from the left fuse box, and plug the two 20-pin connectors (white) of the security system wire harness in between. VEHICLE 20-PIN CONNECTOR 1-PIN CONNECTOR OF SECURITY SYSTEM WIRE HARNESS (WHITE) LEFT FUSE BOX No.
33. Remove the clip from the hole in the left knee bolster, use a utility knife to cut the clip off of the vehicle harness. Take care not to damage the vehicle harness. 37. Position the 5-pin and 4-pin relays onto the other relay bracket, and install one 6 x 12 mm washer-bolt and 6 mm nut. RELAY BRACKET LEFT KNEE BOLSTER 6 mm FLANGE NUT 6 x 12 mm WASHER-BOLT 4-PIN RELAY About 45° VEHICLE HARNESS 5-PIN RELAY HARNESS CLIP (Cut and discard.) 34. Assemble three fuse cases as shown.
39. Route the 2-pin connector of the LED through the lower steering column cover, and connect it to the 2-pin connector of the security system wire harness. Reinstall the lower and upper steering column covers. UPPER STEERING COLUMN COVER 41. On the left of the steering wheel, secure the security system wire harness to the vehicle harness with three long wire ties in the areas shown.
43. Plug the 3-pin connector of the security system wire harness into the 3-pin connector of the disarm switch harness. Plug the 22-pin connector of the security system wire harness into the control unit; then reinstall the driver's dashboard lower cover. 46. Route the sub-harness along the vehicle harness. Inside the glove box, locate the 2-pin connector blue-taped to the vehicle harness, and remove the blue tape to free the connector.
