® Owner's Manual Snowthrower HS520A • HS520AS ® ® EM 31V10600 00X31-V10-6000 IPC 125000007 PRINTED IN U.S.A. ©1999 American Honda Motor Co., Inc.
B WARNING: B The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Keep this owner's manual handy, so you can refer to it any time. This owner's manual is considered a permanent part of the snowthrower and should remain with the snowthrower if resold. The information and specifications included in this publication were in effect at the time of approval for printing. Honda Power Equipment Mfg, Inc.
HS520.book Page 1 Monday, May 14, 2001 12:36 PM INTRODUCTION Congratulations on your selection of a Honda snowthrower. We are certain you will be pleased with your purchase of one of the finest snowthrowers on the market. We want to help you get the best results from your new snowthrower and to operate it safely. This manual contains the information on how to do that; please read it carefully. As you read this manual, you will find information preceded by a NOTICE symbol.
HS520.book Page 2 Monday, May 14, 2001 12:36 PM INTRODUCTION A FEW WORDS ABOUT SAFETY Your safety and the safety of others is very important, and using this snowthrower safely is an important responsibility. To help you make informed decisions about safety, we have provided operating procedures and other information on labels and in this manual. This information alerts you to potential hazards that could hurt you or others.
HS520.book Page 3 Monday, May 14, 2001 12:36 PM CONTENTS SNOWTHROWER SAFETY...................................................................................... 4 IMPORTANT SAFETY INFORMATION.............................................................. 4 SAFETY LABEL LOCATIONS ............................................................................ 7 CONTROLS & FEATURES ....................................................................................... 8 COMPONENT & CONTROL LOCATIONS ............
HS520.book Page 4 Monday, May 14, 2001 12:36 PM SNOWTHROWER SAFETY IMPORTANT SAFETY INFORMATION Honda snowthrowers are designed to clear snow from driveways and walkways. Other uses can result in injury to the operator or damage to the snowthrower and other property. Most accidents with snowthrowers can be prevented if you follow all instructions in this manual and on the snowthrower.
HS520.book Page 5 Monday, May 14, 2001 12:36 PM SNOWTHROWER SAFETY Keep Shields in Place Guards and shields are designed to protect you from being hit by thrown objects and to keep you from touching hot engine parts and moving components. For your safety and the safety of others, keep all shields in place when the engine is running. Adjust the snow discharge chute to avoid hitting the operator, bystanders, windows, and other objects with ejected snow.
HS520.book Page 6 Monday, May 14, 2001 12:36 PM SNOWTHROWER SAFETY Operating Near Roads Always watch for vehicle traffic when operating the snowthrower near roads and driveways. Never operate the snowthrower on public roads. Operator Responsibility Know how to stop the snowthrower quickly in case of emergency. Understand the use of all snowthrower controls. Never permit anyone to operate the snowthrower without proper instruction. Do not let children operate the snowthrower.
HS520.book Page 7 Monday, May 14, 2001 12:36 PM SNOWTHROWER SAFETY SAFETY LABEL LOCATIONS These labels warn you of potential hazards that can cause serious injury. Read them carefully. If a label comes off or becomes hard to read, contact your Honda snowthrower dealer for a replacement. B DANGER B DANGER B CAUTION HOT MUFFLER CAN BURN YOU. Stay away if engine has been running. KEEP HANDS AND FEET AWAY FROM AUGER WHILE ENGINE IS RUNNING.
HS520.book Page 8 Monday, May 14, 2001 12:36 PM CONTROLS & FEATURES COMPONENT & CONTROL LOCATIONS Use the two illustrations on this page to locate and identify the most frequently used controls.
HS520.book Page 9 Monday, May 14, 2001 12:36 PM CONTROLS & FEATURES CONTROLS Fuel Valve OFF The fuel valve opens and closes the fuel line leading from the fuel tank to the carburetor. Make sure that the fuel valve is positioned exactly at either the ON or OFF position. When the snowthrower is not in use, always leave the fuel valve in the OFF position to reduce the possibility of fuel leakage. ON Engine Switch ON The engine switch controls the ignition system.
HS520.book Page 10 Monday, May 14, 2001 12:36 PM CONTROLS & FEATURES Choke Knob The choke knob is used to open or close the choke. CLOSED is used when the engine is cold. CLOSED OPEN The OPEN position provides the correct fuel mixture for operation after the engine has warmed up, and for starting a warm engine. Chute Guide Handle Use this control to guide the snow discharge angle and direction.
HS520.book Page 11 Monday, May 14, 2001 12:36 PM BEFORE OPERATION ARE YOU READY TO GET STARTED? Your safety is your responsibility. A little time spent in preparation will significantly reduce your risk of injury. Knowledge Read and understand this manual. Know what the controls do and how to operate them. Familiarize yourself with the snowthrower and its operation before you begin using it. Know how to quickly shut off the snowthrower in case of an emergency.
HS520.book Page 12 Monday, May 14, 2001 12:36 PM BEFORE OPERATION Check the General Condition of the Snowthrower: • • • • • • Look around and underneath the snowthrower for signs of oil or gasoline leaks. Check the auger housing and the discharge chute for accumulation of packed snow or ice. Clean the auger housing and discharge chute before starting the snowthrower. Look for signs of damage. Check each control for proper operation. Check the scraper bar for wear. Replace it if necessary (page29).
HS520.book Page 13 Monday, May 14, 2001 12:36 PM OPERATION SNOWTHROWING PRECAUTIONS Before operating the snowthrower for the first time, please review both the SNOWTHROWER SAFETY chapter (page 4) and the BEFORE OPERATION chapter (page11). Even if you have operated other snowthrowers, take time to become familiar with how this snowthrower works, and practice in a safe area until you build up your skills. Never tamper with, or alter any of the controls or safety devices on the snowthrower.
HS520.book Page 14 Monday, May 14, 2001 12:36 PM OPERATION 2. If the engine is cold, pull the choke knob out to the CLOSED position. CLOSED 3. Start the engine. Electric Start (AS model only): a. Connect an extension cord to the starter box first, then to a 120 volt ac outlet. 120 VAC OUTLET 3-CONDUCTOR EXTENSION CORD STARTER BOX PLUG To minimize the possibility of potentially dangerous electrical shock, always use a 3-conductor power cord with a power rating of no less than 15 amps.
HS520.book Page 15 Monday, May 14, 2001 12:36 PM OPERATION c. Push the starter button until the engine starts. After the engine starts, disconnect the power cord from the electrical outlet, and then from the switch box. NOTICE Do not operate the starter for more than 15 seconds. If the engine fails to start, release the button and allow the starter to cool for 5 minutes before operating it again. Manual (Pull) Starting a. Turn the engine switch to the ON position. ON ON HS520A HS520AS b.
HS520.book Page 16 Monday, May 14, 2001 12:36 PM OPERATION 4. Let the engine warm up for several minutes. If the choke knob has been pulled to the CLOSED position to start the engine, gradually push it to the OPEN position as the engine warms up. STOPPING THE ENGINE To stop the engine in an emergency, turn the engine switch to the OFF position. Under normal conditions, use the following procedure. 1. Release the auger clutch lever. The auger will stop operation. RELEASE 2.
HS520.book Page 17 Monday, May 14, 2001 12:36 PM OPERATION CLEARING SNOW 1. Press down on the handlebar to raise the front of the snowthrower slightly. Roll the snowthrower over to the snow area. 2. Use the chute guide handle (page10) to adjust the direction for the discharged snow to travel. ENGAGE AUGER 3. Engage the auger clutch lever. The auger will begin to spin. 4. Tilt the snowthrower forward slightly with handlebar to engage the auger into the snow.
HS520.book Page 18 Monday, May 14, 2001 12:36 PM OPERATION • If the snow is deeper than the height of the auger, remove it in several layers, as shown here. REMOVING OBSTRUCTIONS If the discharge chute or snow blowing mechanism becomes restricted, review clearing snow information (page12) to reduce the possibility of reoccurring obstructions. 1. Before removing the obstruction, be sure to stop the engine, and make sure that all rotating parts have come to a complete stop.
HS520.book Page 19 Monday, May 14, 2001 12:36 PM SERVICING YOUR HONDA SNOWTHROWER THE IMPORTANCE OF PROPER MAINTENANCE Proper maintenance is essential for safe, economical, and trouble-free operation. It will also help reduce air pollution. To help you properly care for your snowthrower, the following pages include a maintenance schedule, routine inspection procedures, and simple maintenance procedures using basic hand tools.
HS520.book Page 20 Monday, May 14, 2001 12:36 PM SERVICING YOUR HONDA SNOWTHROWER MAINTENANCE SAFETY Some of the most important safety precautions follow. However, we cannot warn you of every conceivable hazard that can arise in performing maintenance. Only you can decide whether or not you should perform a given task. B WARNING Failure to properly follow maintenance instructions and precautions can cause you to be seriously hurt or killed.
HS520.
HS520.book Page 22 Monday, May 14, 2001 12:36 PM SERVICING YOUR HONDA SNOWTHROWER REFUELING FUEL TANK CAPACITY: 0.3 US gallon (1.3 liters) Stop the engine, remove the cap and check the fuel level. Refill the tank if the fuel level is low. Do not fill above the base of the filler neck. MAXIMUM FILL POINT B WARNING Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. • Stop the engine and keep heat, sparks, and flame away. • Handle fuel only outdoors.
HS520.book Page 23 Monday, May 14, 2001 12:36 PM SERVICING YOUR HONDA SNOWTHROWER FUEL RECOMMENDATIONS Use unleaded gasoline with a pump octane rating of 86 or higher. These engines are certified to operate on unleaded gasoline. Unleaded gasoline produces fewer engine and spark plug deposits and extends exhaust system life. Never use stale or contaminated gasoline or an oil/gasoline mixture. Avoid getting dirt or water in the fuel tank.
HS520.book Page 24 Monday, May 14, 2001 12:36 PM SERVICING YOUR HONDA SNOWTHROWER Engine Oil Change Drain the oil while the engine is still warm to assure rapid and complete draining. DRAIN PLUG & WASHER 1. Place the snowthrower on a level surface. 2. Place a suitable container below the drain bolt to catch the used oil, then remove the oil filler cap/dipstick and the drain plug. 3. Allow the used oil to drain completely, then reinstall the drain plug, and tighten it securely.
HS520.book Page 25 Monday, May 14, 2001 12:36 PM SERVICING YOUR HONDA SNOWTHROWER Engine Oil Recommendations SAE 5W-30 G Y IN G II R VI C E I SE SJ ER EN SAE 5W-30 is recommended for general use. Other viscosities shown in the chart may be used when the average temperature in your area is within the indicated range. The SAE oil viscosity and service classification are on the API label on the oil container.
HS520.book Page 26 Monday, May 14, 2001 12:36 PM SERVICING YOUR HONDA SNOWTHROWER A replacement spark plug may be purchased from a servicing Honda snowthrower dealer. See page 49 for a part number list. SPARK PLUG: BPR5ES (NGK) or W16EPR-U (DENSO) 3. Measure the plug gap with a feeler gauge. Correct as necessary by 0.028 ~ 0.031 inch bending the side electrode. (0.70 ~ 0.80 mm) PLUG GAP: 0.028 - 0.031 inch (0.70 - 0.80 mm) 4.
HS520.book Page 27 Monday, May 14, 2001 12:36 PM SERVICING YOUR HONDA SNOWTHROWER AUGER Clutch Lever Inspection 7-1/2 ~ 8 inches (190 ~ 205 mm) 1. Move the clutch lever until you feel resistance from the cable. Measure the distance as shown. CLUTCH LEVER DISTANCE: 7-1/2 ~ 8 inches (190 ~ 205 mm) Adjustment SPRING COVER 1. Pull the spring cover up to expose the tension spring. Change the position of either the cable or spring on the metal plate so the clutch lever distance is correct.
HS520.book Page 28 Monday, May 14, 2001 12:36 PM SERVICING YOUR HONDA SNOWTHROWER Belt Tension Inspection & Adjustement 1. Pull the spring cover up to expose the belt tension spring. Have a helper engage the auger clutch lever. Measure the length of the exposed coils as shown. 2. Remove the z-bend fitting from the upper hole on the auger clutch lever, and install it into the lower hole. Recheck the spring length. If it is still out of specification, check the auger clutch lever (P. 27).
HS520.book Page 29 Monday, May 14, 2001 12:36 PM SERVICING YOUR HONDA SNOWTHROWER Scraper Bar The scraper bar wears with normal use and must be replaced when it reaches its service limit. The scraper bar thickness and adjustment determine the clearance between the rubber paddles and the ground. Inspection 1. Turn the engine switch to the OFF position, and disconnect the spark plug cap, so the engine cannot be accidentally started. 2. Examine the scraper bar and verify it contacts the ground evenly.
HS520.book Page 30 Monday, May 14, 2001 12:36 PM SERVICING YOUR HONDA SNOWTHROWER A replacement scraper bar may be purchased from a servicing Honda snowthrower dealer. See page49 for a part number list. 4. Measure the distance between the ground and lowest point on the rubber paddle on the auger. 1/16 ~ 1/8 inch (1 ~ 3mm) PADDLE GROUND CLEARANCE: 1/16 ~ 1/8 inch (1 ~ 3 mm) Adjustment/Replacement 1. Loosen (don’t remove) the three hex nuts on the scraper bar. CARRIAGE BOLT (3) 2.
HS520.book Page 31 Monday, May 14, 2001 12:36 PM STORAGE STORAGE PREPARATION Proper storage preparation is essential for keeping your snowthrower troublefree and looking good. The following steps will help to keep rust and corrosion from impairing your snowthrower’s function and appearance, and will make the engine easier to start when you use the snowthrower again. Cleaning 1. Rinse the auger housing and wheels with a garden hose. Wipe the rest of the snowthrower with a moist rag. 2.
HS520.book Page 32 Monday, May 14, 2001 12:36 PM STORAGE Adding a Fuel Stabilizer to Extend Fuel Storage Life When adding a fuel stabilizer, fill the fuel tank with fresh gasoline. If only partially filled, air in the tank will promote fuel deterioration during storage. If you keep a container of gasoline for refueling, be sure that it contains only fresh gasoline. Add fuel stabilizer following the manufacturer's instructions.
HS520.book Page 33 Monday, May 14, 2001 12:36 PM STORAGE Engine Oil 1. Change the engine oil (page24). 2. Remove the spark plug (page25). 3. Pour a tablespoon (5 ~ 10 cc) of clean engine oil into the cylinder. 4. Pull the starter rope slowly several times to distribute the oil. 5. Reinstall the spark plug. 6. Pull the starter grip until resistance is felt. This will close the valves and protect the engine from internal corrosion.
HS520.book Page 34 Monday, May 14, 2001 12:36 PM STORAGE STORAGE PRECAUTIONS If your snowthrower will be stored with gasoline in the fuel tank and carburetor, it is important to reduce the hazard of gasoline vapor ignition. Select a well-ventilated storage area away from any appliance that operates with a flame, such as a furnace, water heater, or clothes dryer. Also avoid any area with a spark-producing electric motor, or where power tools are operated.
HS520.book Page 35 Monday, May 14, 2001 12:36 PM TRANSPORTING BEFORE LOADING If the engine has been running, allow it to cool for at least 15 minutes before loading the snowthrower on the transport vehicle. A hot engine and exhaust system can burn you and can ignite some materials. Turn the fuel valve to OFF. This will prevent carburetor flooding and reduce the possibility of fuel leakage.
HS520.book Page 36 Monday, May 14, 2001 12:36 PM TAKING CARE OF UNEXPECTED PROBLEMS ENGINE PROBLEMS Electric starter does not operate Possible cause Correction Check electrical outlet. No electric current from outlet. Try known good electrical outlet. Start engine by using the recoil starter. Check power cord. Defective power cord. Try another power cord. Start engine with the recoil starter. Starter operates, but engine will not start Possible cause Correction Check fuel delivery to engine.
HS520.book Page 37 Monday, May 14, 2001 12:36 PM TAKING CARE OF UNEXPECTED PROBLEMS Engine has low power Possible cause Correction Check ground speed. Fast ground speed when blowing wet, deep snow puts excessive load on engine. Operate at slower ground speed. Snowthrowing swath too wide for snow conditions. Wet, deep snow can put an excessive load on engine. Reduce snowthrowing swath. Check auger housing. Discharge chute restricted. Clear discharge chute obstructions (page18). Check spark plug.
HS520.book Page 38 Monday, May 14, 2001 12:36 PM TAKING CARE OF UNEXPECTED PROBLEMS SNOWTHROWER PROBLEMS Won't blow snow Possible cause Correction Check auger housing. Discharge chute restricted. Foreign object stopping auger from rotating. Clear discharge chute of obstructions (page18). Remove foreign object. Auger not engaging. Belt worn, not on pulleys or not properly installed. See servicing Honda snowthrower dealer.
HS520.book Page 39 Monday, May 14, 2001 12:36 PM SET-UP Tools Required • 12 mm wrench, 10 mm wrench, and a Phillips-head screwdriver Unpacking 1. Remove all the cardboard. Inspect the loose parts. Missing parts may be obtained from a servicing Honda snowthrower dealer. Qty.
HS520.book Page 40 Monday, May 14, 2001 12:36 PM SET-UP 2. Pull the clutch cable enough to insert the “Z” fitting on the cable through the auger clutch lever as shown here. Check the lever as shown on page . AUGER CLUTCH LEVER “Z” FITTING 3. Install the starter bracket using the hardware removed from step 2 on the previous page. For the HS520AS, snap the starter rope into the rope guide on the handlebar and install the two cable ties. Trim the cable ties to a length of 3/8 inch (10 mm).
HS520.book Page 41 Monday, May 14, 2001 12:36 PM SET-UP 4. Install the discharge chute using the three 6 mm Phillips head screws and 6 mm self-locking nuts. Make sure the screws go on the inside and the nuts on the outside. Tighten the nuts securely: HEX NUT TORQUE: 7 ft-lbs (10 N•m) PHILLIPS HEAD SCREW (3) 6 mm NUT (3) 6 mm NUT (3) PHILLIPS HEAD SCREW (3) CHUTE BASE CHUTE CORRECTLY ASSEMBLED Add Oil & Fuel 1. The snowthrower is shipped WITHOUT OIL in the engine. 2.
HS520.book Page 42 Monday, May 14, 2001 12:36 PM TECHNICAL & CONSUMER INFORMATION TECHNICAL INFORMATION Serial Number Locations Record the engine and frame serial numbers in the spaces below. You may need these serial numbers when ordering parts, and when making technical or warranty inquiries (page54). ENGINE SERIAL NUMBER Use a flashlight to view through the hole for the exhaust pipe. The number starts with “GC...
HS520.book Page 43 Monday, May 14, 2001 12:36 PM TECHNICAL & CONSUMER INFORMATION Carburetor Modification for High Altitude Operation At high altitude, the standard carburetor air-fuel mixture will be too rich. Performance will decrease, and fuel consumption will increase. A very rich mixture will also foul the spark plug and cause hard starting. High altitude performance can be improved by specific modifications to the carburetor.
HS520.book Page 44 Monday, May 14, 2001 12:36 PM TECHNICAL & CONSUMER INFORMATION Oxygenated Fuels Some conventional gasolines are being blended with alcohol or an ether compound. These gasolines are collectively referred to as oxygenated fuels. To meet clean air standards, some areas of the United States and Canada use oxygenated fuels to help reduce emissions. If you use an oxygenated fuel, be sure it is unleaded and meets the minimum octane rating requirement.
HS520.book Page 45 Monday, May 14, 2001 12:36 PM TECHNICAL & CONSUMER INFORMATION EMISSION CONTROL SYSTEM Source of Emissions The combustion process produces carbon monoxide, oxides of nitrogen, and hydrocarbons. Control of hydrocarbons and oxides of nitrogen is very important because, under certain conditions, they react to form photochemical smog when subjected to sunlight. Carbon monoxide does not react in the same way, but it is toxic.
HS520.book Page 46 Monday, May 14, 2001 12:36 PM TECHNICAL & CONSUMER INFORMATION Air Index An Air Index Information hang tag/label is applied to engines certified to an emission durability time period in accordance with the requirements of the California Air Resources Board. The bar graph is intended to provide you, our customer, the ability to compare the emissions performance of available engines. The lower the Air Index, the less pollution.
HS520.book Page 47 Monday, May 14, 2001 12:36 PM TECHNICAL & CONSUMER INFORMATION Replacement Parts The emission control systems on your new Honda engine were designed, built, and certified to conform with EPA and California emission regulations. We recommend the use of genuine Honda parts whenever you have maintenance done. These original-design replacement parts are manufactured to the same standards as the original parts, so you can be confident of their performance.
HS520.book Page 48 Monday, May 14, 2001 12:36 PM TECHNICAL & CONSUMER INFORMATION SPECIFICATIONS FRAME Description code Length Width Height Dry weight SZBG 49.5 inches (1258 mm) 20.7 inches (527 mm) 40.4 (1026 mm) HS520A: 76 lbs (34.5 kg) HS520AS:86 lbs (39.0 kg) Snow clearance (h x w) 12 x 20 inches (306 x 500 mm) Max. snowthrowing distance front: 26 feet (8 m) (varies with conditions and snow) left/right: 16 feet (5 m) Continuous operating time 1.
HS520.book Page 49 Monday, May 14, 2001 12:36 PM TECHNICAL & CONSUMER INFORMATION CONSUMER INFORMATION Honda Publications These publications will give you additional information for maintaining and repairing your snowthrower. You may order them from your servicing Honda snowthrower dealer. Shop Manual This manual covers complete maintenance and overhaul procedures. It is intended to be used by a skilled technician. Parts Catalog This manual provides complete, illustrated parts lists.
HS520.book Page 50 Monday, May 14, 2001 12:36 PM TECHNICAL & CONSUMER INFORMATION Distributor's Limited Warranty PRODUCTS COVERED BY THIS WARRANTY Harmony Snowthrower LENGTH OF WARRANTY (from date of original retail purchase) Noncommercial/Nonrental Commercial/Rental 24 months 3 months To Qualify for this Warranty: The product must be purchased in the United States, Puerto Rico, or the U.S. Virgin Islands from American Honda or a dealer authorized by American Honda to sell those products.
HS520.book Page 51 Monday, May 14, 2001 12:36 PM TECHNICAL & CONSUMER INFORMATION Accessories, Replacement Parts, and Apparel Warranty PRODUCTS COVERED BY THIS WARRANTY LENGTH OF WARRANTY (from date of original retail purchase) Noncommercial/Nonrental Commercial/Rental Accessories 12 months 3 months Replacement Parts 6 months 3 months Apparel 6 months 3 months To Qualify for this Warranty: 1.
HS520.book Page 52 Monday, May 14, 2001 12:36 PM TECHNICAL & CONSUMER INFORMATION Emission Control System Warranty Your new Honda Power Equipment engine complies with both the U.S. EPA and State of California emission regulations. American Honda provides the same emission warranty coverage for engines sold in all 50 states. Your Warranty Rights And Obligations: California The California Air Resources Board and American Honda Motor Co., Inc.
HS520.book Page 53 Monday, May 14, 2001 12:36 PM TECHNICAL & CONSUMER INFORMATION Only Honda approved replacement parts may be used in the performance of any warranty repairs and must be provided without charge to the owner. The use of replacement parts not equivalent to the original parts may impair the effectiveness of your engine emission control system.
HS520.book Page 54 Monday, May 14, 2001 12:36 PM TECHNICAL & CONSUMER INFORMATION Warranty Service Information Honda Power Equipment dealership personnel are trained professionals. They should be able to answer any question you may have. If you encounter a problem that your dealer does not solve to your satisfaction, please discuss it with the dealership's management. The Service Manager or General Manager can help. Almost all problems are solved in this way.
HS520.book Page 55 Monday, May 14, 2001 12:36 PM INDEX A air index .................... page46 altitude, modifications for ..43 assembly see set-up auger paddle clearance ............30 paddle service limit ......... 28 auger clutch lever adjustment ...................... 27 inspection ....................... 27 B belt tension adjustment ...................... 28 inspection ....................... 28 C carburetor draining ........................... 32 modifications for altitude .43 control locations .
HS520.book Page 56 Monday, May 14, 2001 12:36 PM INDEX serial number locations .... 42 set-up ............................... 39 shop manual ..................... 48 spark knock ...................... 23 spark plug gap ................................. 26 recommended type ........ 26 service ............................ 25 specifications .................... 47 storage ............................. 31 cleaning .......................... 31 fuel ................................. 31 precautions .............
QUICK REFERENCE INFORMATION Fuel type Unleaded gasoline with a pump octane of 86 or higher (page 22). Engine Oil capacity 0.3 U.S. gallon (1.3 liter) type Above 15° F (-9° C): SAE 5W-30 Below 15° F (-9° C): SAE 0W-30 (page 25) Spark Plug capacity 0.63 U.S. quart (20.3 fl oz, 0.6 liter) type Regular: NGK- BP6ES, Denso – W16EP-U Resistor: NGK PBR6ES, Denso – W16EPR-U Maintenance gap 0.028 ~ 0.031 inch (0.7 ~ 0.
® EM3 31V10601 00X31-V10-6010 Printed on Recycled Paper IPC 13500.2001.05 PRINTED IN U.S.A.
