User's Manual

ManualsBrandsHonda ManualsAutomobile ElectronicsHonda 08E65-SLN-1001-81

FIT

Keyless Entry System User’s Information

Summary of content (16 pages)

PAGE 1
FIT Keyless Entry System User’s Information
PAGE 2
Contents Introduction ........................................................................................ Precautions ........................................................................................ Remote Control Transmitter Controls and Functions ................................................................. Battery Replacement .................................................................... Remote Control Code Programming How to Program Remote Control Transmitters ....................
PAGE 3
Introduction Congratulations on your purchase of this Honda Keyless Entry System. Your Honda Keyless Entry System is the product of years of research and development. It will give you many years of reliable performance, protection, and convenience. This device complies with FCC Rules Part 15.
PAGE 4
Precautions Remote Control Range Several factors affect and reduce remote control range. Among these are: 1. Proximity to buildings and automobiles. 2. Proximity to high power transmitters (television, radio, cellular, HAM radio, etc.). 3. When the battery becomes weak, the remote control range becomes short. Vehicle construction and the surrounding environment cause reflected waves that may interfere with the low power RF signal transmitted by the remote control.
PAGE 5
Precautions Liquids Outside Cleaning Never submerge the Remote Control Transmitter in water. Use a soft cloth to clean the main unit and remote control. Do not use kerosene, thinner or any other type of solvent. Battery Power In Case of Loss Use the remote control transmitter only when necessary. Every time a button is pressed, the remote control is consuming battery power. If battery is low on power, the transmitting range of the remote control will be affected.
PAGE 6
Remote Control Transmitter Controls and Functions • The doors and the tailgate cannot be locked or unlocked with the remote control transmitter when the key is in the ignition switch. • The doors and the tailgate cannot be locked if any one of the doors is open. • The panic mode will not work when the ignition switch is turned ON.
PAGE 7
Remote Control Transmitter 3 PANIC Button When this button is pressed and held for more than 1 second, the keyless entry system is set to the panic mode. The horn will sound for 30 seconds and the parking light and headlights will flash. To deactivate the panic mode, press the “LOCK”, “UNLOCK” or “PANIC” button or turn the ignition key to the “ON” (II) position. 4 Signal Indicator LED The LED will light when a remote control button is pushed and the remote control is transmitting a control signal.
PAGE 8
Remote Control Transmitter Battery Replacement • The remote control transmitter requires one lithium battery (#CR2025). 1 Using a coin (Quarter) turn the battery cover counterclockwise and remove the cover from the back of the remote control. 2 Remove the used battery. Make sure you install the new battery with the proper polarity. NOTE: If the Lithium battery is incorrectly placed (+ and – polarity), the Remove Control Transmitter can be damaged. 3 Replace the battery cover.
PAGE 9
Remote Control Code Programming How to Program Remote Control Transmitters • For steps 2 through 12, each step must be completed within 5 seconds. For step 13, within 10 seconds for each remote. • Up to 3 remotes can be stored in memory. • All remotes to be programmed must be on hand. • A non programmed remote will work for this procedure. • Turn the ignition key to the “OFF” position to complete the programming procedure. 1 Unlock the doors. 2 Turn the ignition key to the “ON” (II) position.
PAGE 10
Remote Control Code Programming 6 9 10 6 Press the “LOCK” or “UNLOCK” button on the remote control transmitter. 7 Turn the ignition to the “OFF” (0, I) position. 8 Turn the ignition to the “ON” (II) position. 9 Press the “LOCK” or “UNLOCK” button on the remote control transmitter. 10 Turn the ignition to the “OFF” (0, I) position. 11 Turn the ignition to the “ON” (II) position. © 2007 American Honda Motor Co., Inc. - All Rights Reserved.
PAGE 11
Remote Control Code Programming 12 Press the “LOCK” or “UNLOCK” button on the remote control transmitter. • The power door locks cycle to indicate programming mode. • To terminate the programming mode at this point, either turn the ignition key to the “OFF” position or leave the remote’s button untouched for over 10 seconds. To program the remote, perform steps 2 through 12. 13 Press the “LOCK” button of each remote (one at a line) to be stored in memory.
PAGE 12
Specifications Remote Control Transmitter Transmitter Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Radio frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Maximum 30 feet Battery Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Lithium (# CR2025) Battery Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .