User's Manual

ManualsBrandsHonda ManualsAutomobile AccessoriesHonda 08V03-S9A-100B

INSTALLATION

INSTRUCTIONS

Accessory Application Publications No.

Issue Date

SEP 2005

2005-2006 CR-V

PARTS LIST

Automatic Day/Night Mirror Attachment Kit

(sold separately)

P/N 08V03-S9A-101

Clip

Day/night mirror harness

Mirror harness

10 Wire ties

2 EPT sealer

Day/Night mirror

AUTOMATIC DAY/NIGHT

MIRROR

ATTACHMENT KIT

TOOLS AND SUPPLIES REQUIRED

Phillips screwdriver

Flat-tip screwdriver

Small flat-tip screwdriver

10 mm Combination wrench

Ratchet

8 mm, 10 mm and 14 mm Sockets

T20 and T25 Torx bits

Diagonal cutters

Torque wrench

Isopropyl alcohol

Shop towel

Piece of steel wire

Tape measure

Scissors

Electrical tape

Pliers

08V03-S9A-1000-91

Upper and lower covers

Illustration of the Day/Night Mirror Installed on

the Vehicle

INSTALLATION

Customer Information: The information in this

installation instruction is intended for use only by

skilled technicians who have the proper tools,

equipment, and training to correctly and safely add

equipment to your vehicle. These procedures

should not be attempted by “do-it-yourselfers.”

1. Make sure you have the anti-theft code for the radio,

then write down the radio station presets.

2. Disconnect the negative cable from the battery.

Owner’s Manual

4202061

DAY/NIGHT

MIRROR

HARNESS

DAY/NIGHT

MIRROR

HARNESS

FUSE CASE

(2A)

Automatic Day/Night Mirror Kit

(sold separately)

P/N 08V03-S9A-100B

AII 30556

Ground bolt

www.collegehillshonda.com/parts

Summary of content (10 pages)

PAGE 1
www.collegehillshonda.com/parts INSTALLATION INSTRUCTIONS Accessory Application AUTOMATIC DAY/NIGHT MIRROR ATTACHMENT KIT 2005-2006 CR-V PARTS LIST Automatic Day/Night Mirror Attachment Kit (sold separately) P/N 08V03-S9A-101 Upper and lower covers Publications No.
PAGE 2
3. Remove the lens from the roof console (four retaining tabs). 5. Remove the mirror by sliding the mirror up. ROOF CONSOLE MIRROR HOLDER RETAINING TABS (4) MIRROR 4130070H LENS 6. 4. Remove the sunvisor holders. Turn the holder 90°, then pull it out. Remove the roof console (four screws, and unplug one connector). CONNECTOR ROOF CONSOLE 4130081H SUNVISOR HOLDER SCREW 2 of 10 4130060H AII 30556 (0509) © 2005 American Honda Motor Co., Inc. - All Rights Reserved.
PAGE 3
7. Remove the cap from the right sunvisor (four retaining tabs). 10. Remove the passenger’s dashboard under cover (release the three clips and two pins.) CLIPS (3) RETAINING TABS (4) PASSENGER’S DASHBOARD UNDER COVER CAP PINS (2) RIGHT SUNVISOR TORX SCREW 4130090H 8. Remove the right sunvisor (two T25 Torx screws). 9. Remove the door opening weatherstrip from the right front pillar in the area shown. Remove the right front pillar trim (2 clips). CLIP 11. Open the glove box.
PAGE 4
13. Remove the right kick panel (pull to release the two clips). 15. Remove the driver’s dashboard lower cover: RIGHT KICK PANEL TAB • Remove the fuse box lid, and open the pocket. • Remove the two self-tapping screws. • Gently pull out on the driver’s dashboard lower cover to release the eight clips. If equipped, unplug the vehicle connector and remove the lower cover. VEHICLE CONNECTOR (If equipped.) VEHICLE CONNECTOR (If equipped.) DRIVER’S DASHBOARD LOWER COVER CLIP TAB POCKET HOOKS (2) 14.
PAGE 5
17. Remove two self-tapping screws that fasten the heater A/C control panel to the dashboard. Pull the heater A/C control panel out toward you to release the four clips. Unplug the vehicle connector, and remove the heater A/C control panel. 19. On M/T vehicles only, remove the four seat track end covers from the driver’s seat, then remove the four bolts that secure the seat.
PAGE 6
21. On M/T vehicles only, remove the two side covers (four tabs) from the center console. 23. Slide the day/night mirror stay onto the mirror holder, then tighten the T20 Torx screw installed on the day/night mirror. VEHICLE 2-PIN CONNECTOR CLIP TORX SCREW ILLUMINATION BULB Pull SIDE COVER MIRROR HOLDER TABS (4) MIRROR STAY CLIPS (2) FRONT CONSOLE TABS (4) SIDE COVER CLIPS (2) SELF-TAPPING SCREWS (7) DAY/NIGHT MIRROR 4404311T 4130140H 22.
PAGE 7
25. Route the mirror harness through the grooves of the upper and lower covers. Attach the lower cover to the stay of the mirror. MIRROR ROOF LINING HARNESS 28. Unplug the vehicle 21-pin connector (white) and connect the day/night mirror harness 21-pin connectors between the vehicle 21-pin connectors (white). LOWER COVER VEHICLE 21-PIN CONNECTOR (white) DAY/NIGHT MIRROR STAY UPPER AND LOWER COVERS DAY/NIGHT MIRROR 26. Slide the upper cover up and under the roof lining as shown.
PAGE 8
31. Route the day/night mirror harness 4-pin connector with fuse case upwards to the vehicle harness, and then along the vehicle harness to the fuse box through the dashboard pocket opening. DAY/NIGHT MIRROR HARNESS FUSE CASE VEHICLE HARNESS 33. Route the day/night mirror harness ground terminal to the right along the vehicle harness at the rear of the glove box frame.
PAGE 9
35. Tape a piece of steel wire to the 4-pin connector end of the day/night mirror harness. Route the harness end up along the instrument panel side bracket, and out through the clearance between the right front pillar and the instrument panel as shown. 39. Secure the three clips from the day/night mirror harness into the holes in the right front pillar.
PAGE 10
42. Secure the day/night mirror harness to the vehicle harness with four wire ties. 44. Under the dashboard, secure the day/night mirror harness to the vehicle harness with three wire ties. WIRE TIE DAY/NIGHT MIRROR HARNESS VEHICLE HARNESS DAY/ NIGHT MIRROR HARNESS VEHICLE HARNESS WIRE TIE 4202032H 43. Secure the day/night mirror harness to the vehicle harness with three wire ties. WIRE TIE 4202051H DAY/NIGHT MIRROR HARNESS 45.