2000 Accord Coupe Online Reference Owner's Manual Use these links (and links throughout this manual) to navigate through this reference. For a printed owner's manual, click on authorized manuals or go to www.helminc.com. Contents Owner's Identification Form Introduction ......................................................................................................................................... i A Few Words About Safety...........................................................................
Main Menu Owner's Identification OWNER This Owner's Manual should be considered a permanent part of the car, and should remain with the car when it is sold. ADDRESS STREET CITY Main Menu STATE/PROVINCE V. I. N. ZIP CODE / POSTAL CODE Main Menu DELIVERY DATE (Date sold to original retail purchaser) DEALER NAME ADDRESS DEALER NO.
Main Menu Introduction Congratulations ! Your selection of a 2000 Honda Accord was a wise investment. It will give you years of driving pleasure. One of the best ways to enhance the enjoyment of your new Honda is to read this manual. In it, you will learn how to operate its driving controls and convenience items. Afterwards, keep this owner's manual in your car so you can refer to it at any time. Several warranties protect your new Honda.
０００３ Main Menu ▲ Main Menu ▼ ０３／０７／２６ １９：００：４０ ３１ＳＤＰ６１０ A Few FewWords Words About About Safety Safety A Your safety, safety, and and the the safety safety of of others, others, Your is very very important. important. And And operating operating this this is vehicle safely an important car safely is anisimportant responsibility. responsibility.
Main Menu Your Car at a Glance MIRROR CONTROLS (P.99) AIRBAGS (P.9) DIGITAL CLOCK (P.101) DOOR LOCK SWITCH (P.76) HEATING/COOLING CONTROLS (P.110) CLIMATE CONTROL SYSTEM (P.117) AUDIO SYSTEM (P.125, 137) POWER WINDOW SWITCHES (P.96) FUEL FILL DOOR RELEASE (P.161) TRUNK RELEASE HANDLE (P.81) HOOD RELEASE HANDLE (P.162) AUTOMATIC TRANSMISSION (P.178) MANUAL TRANSMISSION (P.
Main Menu Your Car at a Glance INSTRUMENT PANEL BRIGHTNESS (P. 64) WINDSHIELD WIPERS/WASHERS (P. 65, 66) REAR WINDOW DEFOGGER (P. 67) MOONROOF SWITCH (P. 98) CRUISE CONTROL (P. 69) HAZARD WARNING LIGHTS (P. 66) TILT ADJUSTMENT (P. 68) HEADLIGHTS/TURN SIGNALS (P. 62, 64) HORN (P. 61) REMOTE AUDIO CONTROLS (P. 155) (on EX-V6 model) CRUISE CONTROL (P.
Main Menu 4
Main Menu Driver and Passenger Safety This section gives you important information about how to protect yourself and your passengers. It shows you how to use seat belts properly. It explains your Supplemental Restraint System. And it tells you how to properly restrain infants and children in your car. Important Safety Precautions .......... 6 Your Car's Safety Features.............. 7 Seat Belts.......................................8 Airbags...........................................9 Seats & Seat-Backs.
Main Menu Table of Contents Important Safety Precautions You'll find many safety recommendations throughout this section, and throughout this manual. The recommendations on this page are the ones we consider to be the most important. Always Wear Your Seat Belt A seat belt is your best protection in all types of collisions. Airbags supplement seat belts, but airbags are designed to inflate only in a moderate to severe frontal collision.
Main Menu Table of Contents Your Car's Safety Features Your car is equipped with many features that work together to protect you and your passengers during a crash. Some safety features do not require any action on your part. These include a strong steel framework that forms a safety cage around the passenger compartment; front and rear crush zones that are designed to crumple and absorb energy during a crash; and a collapsible steering column.
Main Menu Table of Contents Your Car's Safety Features ０３／０７／１０ Seat Belts For your safety, and the safety of your passengers, your car is equipped with seat belts in all seating positions. Your seat belt system also includes a light on the instrument panel to remind you and your passengers to fasten your seat belts. Why Wear Seat Belts Seat belts are the single most effective safety device for adults and larger children. (Infants and smaller children must be properly restrained in child seats.
Main Menu Table of Contents Your Car's Safety Features Airbags the seat belts. Airbags offer no protection in rear impacts, rollovers, or minor frontal or side collisions. Airbags can pose serious hazards. Your car has a Supplemental Restraint System (SRS) with front airbags to help protect the heads and chests of the driver and a front seat passenger during a moderate to severe frontal collision.
Main Menu Table of Contents Your Car's Safety Features Seats & Seat-Backs Your car's seats are designed to keep you in a comfortable, upright position so you can take full advantage of the protection offered by seat belts and the energy absorbing materials in the seats. How you adjust your seats and seatbacks can also affect your safety.
Main Menu Table of Contents Your Car's Safety Features Pre-Drive Safety Checklist To make sure you and your passengers get the maximum protection from your car's safely features, check the following each time before you drive away: All adults, and children who have outgrown child safety seats, are wearing their seat belts and wearing them properly (see page 15). Any infant or small child is properly restrained in a child seat in the back seat (see page 20).
Main Menu Table of Contents Protecting Adults Introduction The following pages provide instructions on how to properly protect the driver and other adult occupants. These instructions also apply to children who have outgrown child seats and are large enough to wear lap/shoulder belts. (See page 35 for important additional guidelines on how to properly protect larger children.) 1. Close and Lock the Doors After everyone has entered the car, be sure the doors are closed and locked. 2.
Main Menu Table of Contents Protecting Adults Most shorter drivers can get far To reduce the chance of injury, wear enough away from the steering your seat belt properly, sit upright wheel and still reach the pedals. with your back against the seat, and However, if you are concerned about move the seat as far back as possible sitting too close, we recommend that from the steering wheel while still ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ you investigate whether some type maintaining full control of the car.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Protecting Adults A front passenger should also adjust the seat-back to an upright position, but as far from the dashboard as possible. A passenger who sits too close to the dashboard could be injured if the front airbag inflates. Reclining a seat-back so that the shoulder part of the belt no longer rests against the occupant's chest reduces the protective capability of the belt.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Protecting Adults Improperly positioning head restraints reduces their effectiveness and you can be seriously injured in a crash. Make sure head restraints are in place and positioned properly before driving. Properly adjusted head restraints will help protect occupants from whiplash and other crash injuries. See page 92 for how to adjust the head restraints. 5.
Main Menu Table of Contents Protecting Adults If necessary, pull up on the belt again to remove any slack from the shoulder part, then check that the belt rests across the center of your ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ chest and over your shoulder. This spreads the forces of a crash over the strongest bones in your upper body. Improperly positioning the seat belts can cause serious injury or death in a crash. Make sure all seat belts are properly positioned before driving.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ Protecting Adults 7.Maintain a Proper Sitting Position After all occupants have adjusted their seats and put on seat belts, it is very important that they continue to sit upright, well back in their seats, with their feet on the floor, until the car is parked and the engine is off. Sitting improperly can increase the chance of injury during a crash.
Main Menu Table of Contents Protecting Adults Advice for Pregnant Women Pregnant women should also sit upright and as far back as possible from the steering wheel or dashboard. This will reduce the risk of injuries to both the mother and her unborn child that can be caused by a crash or an inflating airbag. Each time you have a check-up, ask your doctor if it's okay for you to drive.
Main Menu Table of Contents Protecting Adults Do not place hard or sharp objects between yourself and a front airbag. Carrying hard or sharp objects on your lap, or driving with a pipe or other sharp object in your mouth, can result in injuries if your front airbag inflates. On models with side airbags, do not attach hard objects on or near a front door. If a side airbag inflates, a cup holder or other hard object attached on or near the door could be propelled inside the car and hurt someone.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Protecting Children Children who are unrestrained or improperly restrained can be seriously injured or killed in a crash. Any child too small for a seat belt should be properly restrained in a child seat. A larger child should be properly restrained with a seat belt. Children depend on adults to protect them. However, despite their best intentions, many parents and other adults may not know how to properly protect young passengers.
Main Menu Table of Contents Protecting Children Children Should Sit in the Back Seat According to accident statistics, children of all ages and sizes are safer when they are restrained in the back seat, not the front seat. The National Highway Traffic Safety Administration and Transport Canada recommend that all children ages 12 and under be properly restrained in the back seat. In the back seat, children are less likely to be injured by striking hard interior parts during a collision or hard braking.
Main Menu Table of Contents Protecting Children U.S. Models To remind you of the passenger's front airbag hazards, and that children must be properly restrained in the back seat, your car has warning labels on the dashboard and on the driver's and front passenger's visors. Please read and follow the instructions on these labels. Canadian Models To remind you of the front airbag hazards, your car has warning labels on the driver's and front passenger's visors.
Main Menu Table of Contents Protecting Children If You Must Drive with Several Children Your car has three seating positions in the back seat where children can be properly restrained. If you ever have to carry more than three children in your car: Place the largest child in the front seat, provided the child is large enough to wear a seat belt properly (see page 35 ). Move the vehicle seat as far to the rear as possible (see page 12 ). Have the child sit upright and well back in the seat (see page 17).
Main Menu Table of Contents Protecting Children General Guidelines for Using Child Seats The following pages give general guidelines for selecting and installing child seats for infants and small children. Selecting a Child Seat To provide proper protection, a child seat should meet three requirements: 1. The child seat should meet safety standards. The child seat should meet Federal Motor Vehicle Safety Standard 213 (FMVSS 213) or Canadian Motor Vehicle Safety Standard 213 (CMVSS 213).
Main Menu Table of Contents Protecting Children 3. The child seat should fit the vehicle seating position (or positions) where it will be used. Due to variations in the design of child seats, vehicle seats, and seat belts, all child seats will not fit all vehicle seating positions. Small Children: A child who is too large for a rear-facing child seat, and who can sit up without support, should be restrained in a forwardfacing child seat.
Main Menu Table of Contents Protecting Children Placing a Child Seat This page briefly summarizes Honda's recommendations on where to place rear-facing and forwardfacing child seats in your car. Airbags Pose Serious Risks to Children The passenger's front airbag inflates with enough force to kill or seriously injure an infant in a rear-facing child seat. A small child in a forward-facing child seat is also at risk.
Main Menu Table of Contents Protecting Children Installing a Child Seat To provide security during normal driving maneuvers as well as during a collision, we recommend that parents secure a child seat as firmly as possible. 1. Secure the child seat to the car with a seat belt. All child seats must be secured to the car with the lap part of a lap/shoulder belt. A child whose seat is not properly secured to the car can be endangered in a crash.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Protecting Children Protecting Infants Rear-Facing Child Seat Placement Placing a rear-facing child seat in the front seat can result in serious injury or death if the passenger's front airbag inflates. Always place a rear-facing child seat in the back seat, not the front. Child Seat Type Only a rear-facing child seat provides proper support for a baby's head, neck, and back.
Main Menu Table of Contents Protecting Children Rear-Facing Child Seat Installation The lap/shoulder belts in the back seats have a locking mechanism that must be activated to secure a child seat. The following pages provide instructions and tips on how to secure a rear-facing child seat with this type of seat belt. 1. With the child seat in the desired back seating position, route the belt through the child seat according to the seat maker's instructions, then insert the latch plate into the buckle.
Main Menu Table of Contents Protecting Children To deactivate the locking mechanism and remove a child seat, unlatch the buckle, unroute the seat belt, and let the belt fully retract. 4. After confirming that the belt is locked, grab the shoulder part of the belt near the buckle and pull up to remove any slack from the lap part of the belt. Remember, if the lap part of the belt is not tight, the child seat will not be secure.
Main Menu Table of Contents Protecting Children Rear-Facing Child Seat Installation Tips For proper protection, an infant must ride in a reclined, or semi-reclined position. To determine the proper reclining angle, check with the baby's doctor or follow the seat maker's recommendations. When properly installed, a rearfacing child seat may prevent the driver or a front-seat passenger from moving the seat as far back as recommended (see page 12).
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ Protecting Children Protecting Small Children We also recommend that a small child stay in the child seat as long as possible, until the child reaches the weight or height limit for the seat. Child Seat Placement In this car, the best place to install a forward-facing child seat is in one of the seating positions in the back seat.
Main Menu Table of Contents Protecting Children Child Seat Installation The lap/shoulder belts in the back and front passenger seating positions have a locking mechanism that must be activated to secure a child seat. The following pages provide instructions and tips on how to secure a forward-facing child seat with this type of seat belt. 1.
Main Menu Table of Contents Protecting Children To deactivate the locking mechanism in order to remove a child seat, unlatch the buckle, unroute the seat belt, and let the belt fully retract. 4. After confirming that the belt is locked, grab the shoulder part of the belt near the buckle and pull up to remove any slack from the lap part of the belt. Remember, if the lap part of the belt is not tight, the child seat will not be secure.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Protecting Children Additional Precautions for Small Children Never hold a small child on your lap. If you are not wearing a seat belt in a crash, you could be thrown forward into the dashboard and crush the child. If you are wearing a seat belt, the child can be torn from your arms during a crash.
Main Menu Table of Contents Protecting Children Checking Seat Belt Fit However, if the belt touches or crosses the child's neck, the child needs to use a booster seat. Do not let a child wear a seat belt across the neck. This could result in serious neck injuries during a crash. To determine if a lap/shoulder belt properly fits a child, have the child put on the seat belt. Follow the instructions on page 15 . Then check how the belt fits.
Main Menu Table of Contents Protecting Children Using a Booster Seat A child may continue using a booster seat until the tops of the ears are even with the top of the seat-back. A child of this height should be tall enough to use the lap/shoulder belt without a booster. When Can a Larger Child Sit in Front The National Highway Traffic Safety Administration and Transport Canada recommend that all children ages 12 and under be properly restrained in a back seat.
Main Menu Table of Contents Protecting Children Of course, children vary widely. And while age may be one indicator of when a child can safely ride in the front, there are other important factors you should consider. Physical Size Physically, a child must be large enough for the lap/shoulder belt to properly fit over the hips, chest, and shoulder (see pages 15 and 36). If the seat belt does not fit properly, the child should not sit in the front.
Main Menu Table of Contents Protecting Children Using Child Seats with Tethers Your car has three tether anchorage points on the rear shelf for securing a tether-style child seat to the car. Since a tether can provide additional security, we recommend using a tether whenever one is required or available. Attach the tether strap hook to the tether anchorage point and tighten the strap according to the child seat maker's instructions.
Main Menu Table of Contents Additional Information About Your Seat Belts Seat Belt System Components Your seat belt system includes lap/ shoulder belts in all five seating positions. The seat belt system also includes a light on the instrument panel to remind you and your passengers to fasten your belts. If the driver's seat belt is not fastened before the ignition is turned ON (II), the light will come on and a beeper will also sound.
Main Menu Table of Contents Additional Information About Your Seat Belts All seat belts have an emergency locking retractor. In normal driving, the retractor lets you move freely in your seat while it keeps some tension on the belt. During a collision or sudden stop, the retractor automatically locks the belt to help restrain your body. The seat belts in all seating positions except the driver's have an additional locking mechanism that must be activated to secure a child seat.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Additional Information About Your Seat Belts Seat Belt Maintenance For safety, you should check the condition of your seat belts regularly. Pull each belt out fully and look for frays, cuts, burns, and wear. Check that the latches work smoothly and that the lap/shoulder belts retract easily. Any belt not in good condition or not working properly will not provide good protection and should be replaced as soon as possible. U.S.
Main Menu Table of Contents Additional Information About Your Front Airbags SRS Components Your Supplemental Restraint System (SRS) includes: Two front airbags. The driver's airbag is stored in the center of the steering wheel; the front passenger's airbag is stored in the dashboard. Both are marked "SRS AIRBAG." Sensors that can detect a moderate to severe frontal collision.
Main Menu Table of Contents Additional Information About Your Front Airbags During a frontal crash, your seat belts help restrain your lower body and torso. Your airbag provides a cushion to help restrain and protect your head and chest. After a crash, you may see what looks like smoke. This is actually powder from the airbag's surface. Although the powder is not harmful, people with respiratory problems may experience some temporary discomfort.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ Additional Information About Your Front Airbags How the SRS Indicator Light Works purpose of the SRS SRS The indicator light is to alert you to a potential problem with your front airbags. On all V-6 models and the 4-cylinder EX model with leather interior, this light will also alert you to a potential problem with your side airbags or passenger's side airbag automatic cutoff system (see page 47).
Main Menu Table of Contents Additional Information About Your Side Airbags On all V6 models and the 4-cylinder EX model with leather interior Your car is equipped with side airbags for the driver and a front seat passenger. The airbags are stored in the outer edges of the front seat-backs, and both are marked "SIDE AIRBAG.
Main Menu Table of Contents Additional Information About Your Side Airbags How The Side Airbag Indicator Light Works The purpose of this light is SIDE AIRBAG to alert you if the passenger's side airbag has been automatically shut off. Although Honda does not encourage children to ride in the front, to help prevent injury, your car has an automatic cutoff system for the passenger's side airbag.
Main Menu Table of Contents Additional Information About Your Airbags Airbag Service Your front and side airbag systems (if equipped) are virtually maintenance-free, and there are no parts you can safely service. However, you must have your car serviced if: Your airbags ever inflate. Any airbag that has deployed must be replaced along with the control unit and other related parts. Do not try to remove or replace any airbag by yourself. This must be done by a Honda dealer or a knowledgeable body shop.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Carbon Monoxide Hazard Your car's exhaust contains carbon monoxide gas. You should have no problem with carbon monoxide entering the car in normal driving if you maintain your car properly. Have the exhaust system inspected for leaks whenever: The car is raised for an oil change. You notice a change in the sound of the exhaust. The car was in an accident that may have damaged the underside. Carbon monoxide gas is toxic.
Main Menu Table of Contents Safety Labels These labels are in the locations shown. They warn you of potential hazards that could cause serious injury. Read these labels carefully. If a label comes off or becomes hard to read, contact your Honda dealer for a replacement. DASHBOARD U.S. models only RADIATOR CAP Driver and Passenger Safety SUN VISOR U.S.
Main Menu Instruments and Controls This section gives information about the controls and displays that contribute to the daily operation of your Honda. All the essential controls are within easy reach. Control Locations............................ 52 Indicator Lights................................ 53 Gauges............................................. . 58 Speedometer................................ 58 Tachometer................................. . 58 Odometer..................................... .
Main Menu Table of Contents Control Locations DOOR LOCK SWITCH (P.76) POWER WINDOW SWITCHES (P.96) Instruments and Controls MIRROR CONTROLS (P.99) FUEL FILL DOOR RELEASE (P.161) TRUNK RELEASE HANDLE (P.81) DIGITAL CLOCK (P.101) HOOD RELEASE HANDLE (P. 162) HEATING/COOLING CONTROLS (P.110) CLIMATE CONTROL SYSTEM (P.117) AUDIO SYSTEM (P.
Main Menu Table of Contents Indicator Lights The instrument panel has many indicators to give you important information about your car.
Main Menu Table of Contents Indicator Lights Seat Belt Reminder Light This indicator lights when you turn the ignition switch ON (II). It is a reminder to you and your passengers to protect yourselves by fastening the seat belts. A beeper also sounds if you have not fastened your seat belt. If you do not fasten your seat belt, the beeper will stop after a few seconds but the light stays on until you do. Both the light and the beeper stay off if you fasten your seat belt before turning on the ignition.
Main Menu Table of Contents Indicator Lights U.S. Canada ABS Anti-lock Brake System (ABS) Indicator Only on models equipped with ABS (see page 186) This light normally comes on for a few seconds when you turn the ignition switch ON (II), and when the ignition switch is turned to START (lII). If this light comes on at any other time, there is a problem in the ABS. If this happens, take the car to your dealer to have it checked.
Main Menu Table of Contents Indicator Lights Door and Brake Lamp Monitor The appropriate light comes on in this display if the trunk or either door is not closed tightly. If a brake light does not work, the BRAKE LAMP indicator comes on when you push the brake pedal with the ignition switch ON (II). A burned out brake light is a hazard when drivers behind you cannot tell you are braking. Have your brake lights repaired right away.
Main Menu Table of Contents Indicator Lights High Beam Indicator This light comes on with the high beam headlights. See page 62 for information on the headlight controls. On Canadian models, this indicator conies on with reduced brightness when the Daytime Running Lights (DRL) are on (see page 63). CRUISE CONTROL Washer Level Indicator Canadian models only This light comes on when the washer fluid level is low. Add washer fluid when you see this light come on (see page 224).
Main Menu Table of Contents Gauges U.S. Model shown TACHOMETER MAINTENANCE REQUIRED INDICATOR SPEEDOMETER TRIP METER Speedometer U.S. Models This shows your speed in miles per hour (mph). The smaller inner numbers are the speed in kilometers per hour (km/h). Instruments and Controls FUEL GAUGE TEMPERATURE GAUGE ODOMETER TRIP METER SELECT/RESET BUTTON Canadian Models This shows your speed in kilometers per hour (km/h). The smaller inner numbers are the speed in miles per hour (mph).
Main Menu Table of Contents Gauges Trip Meter This meter shows the number of miles (U.S.) or kilometers (Canada) driven since you last reset it. When you turn the ignition switch to ON (II), the number is displayed. There are two trip meters: Trip A and Trip B. Switch between these displays by pressing the Select/ Reset button repeatedly. Each trip meter works independently, so you can keep track of two different distances.
Main Menu Table of Contents Gauges Maintenance Required Indicator SELECT/RESET BUTTON Your dealer will reset this indicator after completing the scheduled maintenance. If this maintenance is done by someone other than your Honda dealer, reset the indicator as follows. 1. Turn off the engine. 2. Press and hold the select/reset button in the instrument panel, then turn the ignition switch ON (II).
Main Menu Table of Contents Controls Near the Steering Wheel The two levers on the steering column contain controls for driving features you use most often. The left lever controls the turn signals, headlights, and high beams. The right lever controls the windshield washers and wipers. The switches for the hazard warning lights and rear window defogger are located to the right of the steering column.
Main Menu Table of Contents Controls Near the Steering Wheel Headlights The rotating switch on the left lever controls the lights. Turning this switch to the position turns on the parking lights, taillights, instrument panel lights, side-marker lights, and rear license plate lights. Turning the switch to the position turns on the headlights.
Main Menu Table of Contents Controls Near the Steering Wheel Automatic Lighting Off Feature On EX and EX-V6 models The Automatic Lighting Off feature turns off the headlights, parking lights, taillights, side marker lights, license plate lights and instrument panel lights within 15 seconds of removing the key from the ignition switch and closing the driver's door. This feature activates if you leave the headlight switch in the or position, remove the key, open, then close the driver's door.
Main Menu Table of Contents Controls Near the Steering Wheel Instrument Panel Brightness Turn Signals TURN SIGNAL LEVER The knob on the instrument panel controls the brightness of the instrument panel lights. Turn the knob to adjust the brightness. Instruments and Controls Signal a turn or lane change with this lever. Push down on the lever to signal a left turn, and up to signal a right turn. If you push it up or down all the way, the turn signal continues to blink even when you release the lever.
Main Menu Table of Contents Controls Near the Steering Wheel You can vary how often the wipers sweep the windshield by turning the INT TIME ring next to the rotary switch. Windshield Wipers If you turn the INT TIME ring to the shortest delay, the wipers will change from intermittent to low speed operation when vehicle speed exceeds 12 mph (20 km/h). The right lever controls the windshield wipers and washers.
Main Menu Table of Contents Controls Near the Steering Wheel To operate the wipers in mist mode, push the control lever down. The wipers run at high speed until you release the lever. This gives you a quick way to clear the windshield. Instruments and Controls Windshield Washers Hazard Warning To clean the windshield, pull back on the wiper control lever. The washers spray until you release the lever.
Main Menu Table of Contents Controls Near the Steering Wheel Rear Window Defogger LX, EX and LX-V6 models The rear window defogger will clear fog, frost, and thin ice from the window. Push the defogger button to turn it on and off. The light above the button lights to show the defogger is on. If you do not turn it off, the defogger will shut itself off after about 15 minutes. It also shuts off when you turn off the ignition. You have to turn it on again when you restart the car.
Main Menu Table of Contents Controls Near the Steering Wheel Steering Wheel Adjustment See page 17 for important safety information about how to properly ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ position the steering wheel. Make any steering wheel adjustment before you start driving. Adjusting the steering wheel position while driving may cause you to lose control of the car and be seriously injured in a crash.
Main Menu Table of Contents Steering Wheel Controls Using the Cruise Control Cruise Control Cruise control allows you to maintain CRUISE CONTROL MASTER SWITCH a set speed above 25 mph (40 km/h) without keeping your foot on the accelerator pedal. It should be used for cruising on straight, open highways. It is not recommended for conditions such as city driving, ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ winding roads, slippery roads, heavy rain, or bad weather.
Main Menu Table of Contents Steering Wheel Controls The cruise control may not hold the set speed when you are going up and down hills. If your speed increases going down a hill, use the brakes to slow down to the desired speed. This will cancel the cruise control. To resume the set speed, press the RESUME/accel button. The CRUISE CONTROL light on the instrument panel comes on. When climbing a steep hill, the automatic transmission may downshift to hold the set speed.
Main Menu Table of Contents Steering Wheel Controls Even with the cruise control turned on, you can still use the accelerator pedal to speed up for passing. After completing the pass, take your foot off the accelerator pedal. The car will return to the set cruising speed. Cancelling the Cruise Control Resting your foot on the brake or clutch pedal will cause the cruise control to cancel. CANCEL BUTTON You can cancel the cruise control in any of these ways: Tap the brake or clutch pedal.
Main Menu Table of Contents Steering Wheel Controls, Keys and Locks Remote Audio Controls Keys KEY NUMBER PLATE On EX-V6 model These buttons let you control some functions of the audio system without removing your hands from the wheel. Refer to page 155 for a complete explanation. Instruments and Controls MASTER KEY (BLACK) VALET KEY (GREY) Your car comes with two master keys and a valet key.
Main Menu Table of Contents Keys and Locks These keys contain electronic circuits that are activated by the Immobilizer System. They will not work to start the engine if the circuits are damaged. Protect the keys from direct sunlight, high temperature, and high humidity. Do not drop the keys or set heavy objects on them. Keep the keys away from liquids. If they get wet, dry them immediately with a soft cloth. The keys do not contain batteries. Do not try to take them apart.
Main Menu Table of Contents Keys and Locks The system may not recognize your key's coding if another immobilizer key or other metal object is near the ignition switch when you insert the key. To make sure the system recognizes the key code: Do not keep other immobilizer keys on the same key ring. Use a plastic or leather key fob, not metal. Keep other keys away from your car's key and the ignition switch while trying to start the engine.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ Keys and Locks Ignition Switch The ignition switch is on the right side of the steering column. It has four positions: LOCK (0) ACCESSORY (I) ON (II) START (III) LOCK (0) — You can insert or remove the key only in this position. To switch from ACCESSORYto LOCK, you must push the key in slightly as you turn it. If your car has an automatic transmission, the shift lever must also be in Park.
Main Menu Table of Contents Keys and Locks ACCESSORY (I) — In this position, you can operate the audio system and the accessory power socket. ON (II) — This is the normal key position when driving. All features and accessories on the car are usable. Several of the lights on the instrument panel come on as a test when you turn the ignition switch from ACCESSORY to ON. Instruments and Controls START (III) — Use this position only to start the engine.
Main Menu Table of Contents Keys and Locks To lock the passenger's door when getting out of the car, push the lock tab down and close the door. To lock the driver's door, remove the key from the ignition switch and push the lock tab down or push the master switch down, then close the door. Both doors can be locked from the outside by using the key in either door. LOCK TAB Each door has a lock tab at the top of the door. When you push down the lock tab on the driver's door, both doors lock.
Main Menu Table of Contents Keys and Locks Remote Transmitter LED LOCK BUTTON TRUNK RELEASE BUTTON UNLOCK BUTTON PANIC BUTTON On EX and EX-V6 models You can lock and unlock your car with the remote transmitter. When you push the LOCK button, both doors lock. The parking lights, side marker lights, and taillights flash once. Instruments and Controls When you push the UNLOCK button once, only the driver's door unlocks. The passenger's door unlocks when you push the button a second time.
Main Menu Table of Contents Keys and Locks Panic Mode Panic mode allows you to remotely activate your car's security system to attract attention. When activated, the horn will sound, and the exterior lights will flash, for about 30 seconds. To activate panic mode, press and hold the PANIC button for about two seconds. To cancel Panic mode before 30 seconds, press any button on the remote transmitter. You can also turn the ignition switch to ON (II).
Main Menu Table of Contents Keys and Locks Transmitter Care Avoid severe shock to the transmitter, such as dropping or throwing it. Also, protect it from extreme hot or cold temperatures. BATTERY Remove the old battery and note the polarity. Make sure the polarity of the new battery is the same (+ side facing up), then insert it in the transmitter. Reinstall the upper half securely. Instruments and Controls Clean the transmitter case with a soft cloth.
Main Menu Table of Contents Keys and Locks Trunk See page 170 for cargo loading and weight limit information. Keep the trunk lid closed at all times while driving to avoid damaging the lid, and to prevent exhaust gas from getting into the interior. See Carbon Monoxide Hazard on page 49 . TRUNK RELEASE HANDLE You can open the trunk in two or three ways: Pull the trunk release handle to the left of the driver's seat. MASTER KEY To close the trunk, press down on the trunk lid.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Keys and Locks Glove Box An open glove box can cause serious injury to your passenger in a crash, even if the passenger is wearing the seat belt. MASTER KEY Always keep the glove box closed while driving. GLOVE BOX To protect items in the trunk when you need to give the key to someone else: 1. Lock the trunk release handle with the master key. 2. Give the person the valet key.
Main Menu Table of Contents HomeLink Universal Transmitter On EX V-6 model The HomeLink Universal Transmitter built into your vehicle can be programmed to operate remotely controlled devices around your home, such as garage doors, lighting, or home security systems. It can replace up to three remote transmitters. Customer Assistance If you have problems with training the HomeLink Universal Transmitter, or would like information on home products that can be operated by the transmitter, call (800) 355-3515.
Main Menu Table of Contents HomeLink Universal Transmitter transmitter to learn the code. Release and press the button on the remote control every two seconds until the transmitter has learned the code. Before you begin — If you just took delivery of your vehicle and have not trained any of the buttons in the HomeLink transmitter before, you should erase any previously learned codes before training the first button.
Main Menu Table of Contents HomeLink Universal Transmitter rolling code garage door opener. Test this by pressing and holding the HomeLink transmitter button you just trained. If the red light blinks for two seconds, then stays on, you have a rolling code garage door opener. You may be able to verify this with the manufacturer's documentation. Go to "Training With a Rolling Code System." 8.
Main Menu Table of Contents HomeLink Universal Transmitter 4. Press and release the button on the HomeLink transmitter. (The same button you trained with the "Training the Transmitter" procedure.) 5. Press and release the HomeLink transmitter button again. This should turn off the training light on the garage door opener unit. (Some systems may require you to press and release the button up to three times.) 6. Press the transmitter button again. It should operate the garage door.
Main Menu Table of Contents Seat Adjustments Front Seat Adjustments See pages 12 — 13 for important safety information and warnings about how to properly position seats and seat-backs. Make all seat adjustments before you start driving. To adjust the seat forward and backward, pull up on the lever under the seat cushion's front edge. Move the seat to the desired position and release the lever. Try to move the seat to make sure it is locked in position.
Main Menu Table of Contents Seat Adjustments Driver's Seat Manual Height Adjustment On LX model The height of your driver's seat is adjustable. Turn the front dial on the outside of the seat cushion to raise the front of the seat bottom and turn the rear dial to raise the rear. Make all adjustments before you start driving. Instruments and Controls Driver's Seat Power Height Adjustment On EX model The height of your driver's seat is power adjustable. Pull up on the switch to raise the seat.
Main Menu Table of Contents Seat Adjustments Driver's Seat Power Adjustments On all V6 models and the 4-cylinder EX model with leather interior See pages 12 — 13 for important safety information and warnings about how to properly position seats and seat-backs. The two power seat adjustment switches are on the outside edge of the seat bottom. The horizontal switch adjusts the seat bottom in several directions. The short vertical switch adjusts the seat-back angle.
Main Menu Table of Contents Seat Adjustments Driver's Lumbar Support Pull the center of the horizontal switch up to raise the seat. Push it down to lower the seat. Instruments and Controls Adjust the seat-back angle by pushing the rear switch in the direction you want to move. On EX and EK-V6 models Vary the lumbar support by moving the lever on the right side of the seat-back. Pivot the lever forward until it stops, then let it return.
Main Menu Table of Contents Seat Adjustments Rear Seat Access Driver's Side Passenger's Side RELEASE LEVER On all V6 models and the 4-cylinder EX model with leather interior To get into the back seat on the driver's side, pull the release lever upward on the side of the seat-back. The seat-back will tilt forward to allow easier entry to the back seat. SEAT-BACK ADJUSTMENT LEVER On LX and EX models To get into the back seat on the driver's side, pull up on the seat-back adjustment lever.
Main Menu Table of Contents Seat Adjustments Head Restraints See page 14 for important safety information and a warning about how to properly position the head restraints. The front head restraints help protect you and your passenger from whiplash and other injuries. They are most effective when you adjust them so the back of the occupant's head rests against the center of the restraint. A taller person should adjust the restraint as high as possible.
Main Menu Table of Contents Seat Adjustments Folding Rear Seat The back of the rear seat folds down to give you direct access to the trunk. Each side folds down separately. With only half the seat folded, you can still carry a passenger in the back seat. The seat-back can be released from inside the car or inside the trunk. GUIDE MASTER KEY To fold down either side of the seatback from inside the car, insert the master key in the lock on the rear shelf.
Main Menu Table of Contents Seat Adjustments Make sure all rear shoulder belts are positioned in front of the rear seatback whenever the seat-back is in its upright position. RELEASE To release the seat-back from inside the trunk, pull the release under the rear shelf. Push the seat-back down, then let go of the release. To lock the seat-back upright, push it firmly against the rear shelf. Make sure it is latched in place by pulling on the top of the seat.
Main Menu Table of Contents Seat Heaters SEAT HEATERS The HI or LO indicator lights and remains lit until you turn it off by pushing the opposite side of the switch lightly. The indicator will turn off. In HI, the heater turns off when the seat gets warm, and turns back on after the seat's temperature drops. It continues to cycle as long as you leave it set on HI. The HI indicator remains lit as a reminder that you have the heater on.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ Power Windows Your car's windows are electricallypowered. Turn the ignition switch to ON (II) to raise or lower any window. MAIN SWITCH Closing a power window on someone's hands or fingers can cause serious injury. Each door has a switch that controls its window. To open the window, push the switch down and hold it. Release the switch when you want the window to stop. Close the window by pulling back on the switch and holding it.
Main Menu Table of Contents Power Windows The master control panel also contains these extra features: AUTO — To open the driver's window fully, push the window switch firmly down and release it. The window automatically goes all the way down. To stop the window from going all the way down, pull back on the window switch briefly. To open the driver's window only partially, push the window switch down lightly and hold it. The window will stop as soon as you release the switch.
Main Menu Table of Contents Moonroof The moonroof has a key-off delay. To tilt up the back of the moonroof, You can still open and close the press and hold the center button moonroof for up to ten minutes after ( ). To close the moonroof, you turn off the ignition. The key-off press and hold the top of the switch delay cancels as soon as you open ( ). To open the moonroof, either door.
Main Menu Table of Contents Mirrors Adjusting the Power Mirrors SELECTOR SWITCH TAB Keep the inside and outside mirrors clean and adjusted for best visibility. Be sure to adjust the mirrors before you start driving. The inside mirror has day and night positions. The night position reduces glare from headlights behind you. Flip the tab on the bottom edge of the mirror to select the day or night position.
Main Menu Table of Contents Mirrors, Parking Brake Parking Brake NOTICE Driving the car with the parking brake applied can damage the rear brakes and axles. HEATED MIRROR BUTTON Available on all Canadian models The outside mirrors are heated to remove fog and frost. With the ignition switch ON (II), turn on the heaters by pressing the button. The light in the button comes on as a reminder. Press the button again to turn the heaters off.
Main Menu Table of Contents Digital Clock, Sunglasses Holder Digital Clock H M R 2. Press and hold the M button until the numbers advance to the desired minutes. You can use R to quickly set the time to the nearest hour. If the displayed time is before the half hour, pressing R sets the clock back to the previous hour. If the displayed time is after the half hour, pressing R sets the clock forward to the beginning of the next hour.
Main Menu Table of Contents Sunglasses Holder, Beverage Holder Beverage Holder INNER LINER Push Some larger styles of sunglasses may not fit in the holder. To open the beverage holder, push on the top. The beverage holder lid is spring-loaded and will swing open. To close it, push it down until it latches. The inner liner can be removed if you want to hold a larger cup. Instruments and Controls Be careful when you are using the beverage holder.
Main Menu Table of Contents Console Compartment LEVER LEVER CONSOLE COMPARTMENT To open the console compartment, pull up on the lower lever and lift the lid. To close, lower the lid and push it down until it latches. On EX and EX-V6 models The console compartment has a Compact Disc holder. You can put small items in the tray located in the console compartment lid. To use the tray, pull up on the upper lever and lift up the armrest pad.
Main Menu Table of Contents Sun Visor, Vanity Mirror Sun Visor EXTENSION Make sure you put the sun visor back in place when you are getting into or out of the car. Do not use the sun visor extension over the rear view mirror. Vanity Mirror SUN VISOR To use the sun visor, pull it down. You can also use the sun visor at the side window. Remove the support rod from the clip and swing the sun visor toward the side window. In this position, the sun visor can be extended by sliding out the extension.
Main Menu Table of Contents Coin Box, Center Pocket, Accessory Power Socket Coin Box Center Pocket COIN BOX The coin box is located under the air vent. To open the coin box, pull the bottom edge. Close it with a firm push. Accessory Power Socket ACCESSORY POWER SOCKET On LX and LX-V6 models The center pocket is located under the audio system. To open the lid, pull it down. Close it with a firm push. To use the accessory power socket, pull out on the cover.
Main Menu Table of Contents Interior Lights Ceiling Light LX, LX-V6 The light goes out when both doors are closed. Spotlights On EX and EX-V6 models The ceiling light (with the switch in the center position) also comes on when you unlock the door with the remote transmitter (see page 78 ). The light fades out after both doors are closed. DOOR ACTIVATED The ceiling light has a three-position switch. In the OFF position, the light does not come on.
Main Menu Table of Contents Interior Lights Courtesy Lights IGNITION SWITCH LIGHT DOOR LIGHT The courtesy light in each door comes on when the door is opened, and goes out when the door is closed. Your car also has a courtesy light in the ignition switch. This light comes on when you open the driver's door. It remains on for several seconds after the door is closed.
Main Menu 108
Main Menu Comfort and Convenience Features The heating and air conditioning systems in your Honda provide a comfortable driving environment in all weather conditions. The standard audio system has many features. This section describes those features and how to use them. (If you selected an optional audio system, refer to the operating instructions that came with it.) On EX and EX-V6 models Your Honda has an anti-theft audio system that requires a code number to enable it.
Main Menu Heating and Cooling On LX, LX-V6 and EX models Proper use of the Heating and Cooling system can make the interior dry and comfortable, and keep the windows clear for best visibility. FAN CONTROL DIAL MODE BUTTONS TEMPERATURE CONTROL DIAL What Each Control Does Fan Control Dial Turning this dial clockwise increases the fan's speed, which increases air flow. Temperature Control Dial Turning this dial clockwise increases the temperature of the air flow.
Main Menu Heating and Cooling Mode Buttons Use the MODE buttons to select the vents the air flows from. Some air will flow from the dashboard corner vents in all modes. Air flows from the center and corner vents in the dashboard. Air flow is divided between the vents in the dashboard and the floor vents. vents. Air flows from the floor Air flow is divided between the floor vents and the defroster vents at the base of the windshield. Air flows from the defroster vents at the base of the windshield.
Main Menu Heating and Cooling Vent Controls CENTER VENT The direction of air flow from the vents in the center and each side of the dashboard is adjustable. To adjust the air flow from the center vent, move the tab up-anddown and side-to-side. Comfort and Convenience Features DRIVER'S-SIDE VENT On the driver's-side vent, move the vent up-and-down and move the tab side-to-side. On the passenger's-side vent, move the tab up-and-down and move the vent side-to-side.
Main Menu Heating and Cooling How to Use the System This section covers how to set up the system controls for ventilation, heating, cooling, dehumidifying, and defrosting. The engine must be running for the heater and air conditioning to generate hot and cold air. The heater uses engine coolant to warm the air. If the engine is cold, it will be several minutes before you feel warm air coming from the system. The air conditioning does not rely on engine temperature.
Main Menu Heating and Cooling To Cool with A/C 1. Turn on the A /C by pressing the button. The light above the button should come on when a fan speed is selected. 2. Make sure the temperature control dial is all the way to the left. 3. Select 4. If the outside air is humid, select Recirculation mode. If the outside air is dry, select Fresh Air mode. 5. Set the fan to the desired speed.
Main Menu Heating and Cooling To Heat To warm the interior: 1. Start the engine. 2. Select and Fresh Air mode. 3. Set the fan to the desired speed. 4. Adjust the warmth of the air with the temperature control dial. To Heat and Dehumidify with Air Conditioning Air conditioning, as it cools, removes moisture from the air. When used in combination with the heater, it makes the interior warm and dry. 1. Switch the fan on. 2. Turn on the air conditioning. 3. Select and Fresh Air mode. 4.
Main Menu Heating and Cooling To remove exterior frost or ice from the windshield and side windows after the car has been sitting out in cold weather: 1. Start the engine. 2. Select When you select the system automatically switches to Fresh Air mode and turns on the A/C. 3. Switch the fan and temperature controls to maximum. To rapidly remove exterior frost or ice from the windshield (on very cold days), first select the Recirculation mode.
Main Menu Climate Control System On EX-V6 model The automatic climate control system in your Honda picks the proper combination of air conditioning, heating, and ventilation to maintain the interior temperature you select. The system also adjusts the fan speed and air flow levels. CENTER VENTS DRIVER'S-SIDE VENT The direction of air flow from the vents in the center and each side of the dashboard is adjustable. To adjust the air flow from the center vent, move the tab up-anddown and side-to-side.
Main Menu Climate Control System PASSENGER'S-SIDE VENT Comfort and Convenience Features
Main Menu Climate Control System Fully-automatic Operation Control in fully-automatic mode, press the AUTO button and set the fan control dial to AUTO, then set the desired temperature by turning the temperature control dial. You will see FULL AUTO in the system's display. The light above the button also shows you which mode, Recirculation or Fresh Air, is selected.
Main Menu Climate Control System Semi-automatic Operation You can manually select various functions of the Climate Control system when it is in FULL AUTO. All other features remain automatically controlled. Making any manual selection causes the word FULL to go out. TEMPERATURE CONTROL DIAL AIR CONDITIONING BUTTON Air Conditioning (A/C) Button Press the A /C button to turn the air conditioning on and off. You will see A/C ON or A/C OFF in the display.
Main Menu Climate Control System Fan Control Dial You can manually select the fan speed by turning the fan control dial. When you turn the dial clockwise, the fan is taken out of automatic mode and starts to run at its lowest speed. Turning the dial fully clockwise increases the fan's speed, which increases air flow. MODE BUTTON FAN CONTROL DIAL Mode Button Use the MODE button to select the vents the air flows from. Some air will flow from the dashboard corner vents in all modes.
Main Menu Climate Control System The main air flow is divided between the floor vents and defroster vents at the base of the windshield. The main air flow comes from the floor vents. The main air flow is divided between the dashboard vents and the floor vents. The main air flow comes from the dashboard vents.
Main Menu Climate Control System The button directs the main air flow to the windshield for faster defrosting. It also overrides any MODE selection you may have made. When you select the A /C turns on automatically and the system selects Fresh Air mode. For faster defrosting, manually set the fan speed to high. You can also increase air flow to the windshield by closing the side vents in the dashboard. When you turn off by pressing the button again, the system returns to its former settings.
Main Menu Climate Control System Sunlight Sensor/Temperature Sensor SUNLIGHT SENSOR The climate control system has two sensors. A sunlight sensor is located in the top of the dashboard and a temperature sensor is next to the steering column. Do not cover the sensors or spill any liquid on them.
Main Menu Audio System AM/FM/Cassette Stereo Audio System For LX and LX-V6 models Your Honda's audio system provides clear reception on both AM and FM bands, while the preset buttons allow you to easily select your favorite stations. The cassette system features Dolby B* noise reduction, automatic sensing of chromium-dioxide (CrO2) tape, and autoreverse for continuous play. * Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation.
Main Menu Audio System Operating the Radio The ignition switch must be in ACCESSORY (I) or ON (II) to operate the audio system. Turn the system on by pushing the PWR/ VOL knob. Adjust the volume by turning the PWR/VOL knob. The band and frequency that the radio was last tuned to is displayed. To change bands, press the AM/FM button. On the FM band, ST will be displayed if the station is broadcasting in stereo. Stereo reproduction on AM is not available.
Main Menu Audio System SCAN — The SCAN function samples all the stations with strong signals on the selected band. To activate it, press the SCAN button, then release it. When the system is in the SCAN mode, SCN shows in the display. The system will scan up the band for a station with a strong signal. When it finds one, it will stop and play that station for approximately five seconds. If you do nothing, the system will then scan for the next strong station and play that for five seconds.
Main Menu Audio System Preset — You can store the frequencies of your favorite radio stations in the six preset buttons. Each button will store one frequency on the AM band, and two frequencies on the FM band. AM/FM BUTTON To store a frequency: 1. Select the desired band, AM or FM. FM1 and FM2 let you store two frequencies with each Preset button. 2. Use the TUNE or SEEK function to tune the radio to a desired station. 3. Pick the Preset button you want for that station.
Main Menu Audio System Adjusting the Sound Balance/Fader — These two controls adjust the strength of the sound coming from each speaker. The Balance control adjusts the sideto-side strength, while the Fader control adjusts the front-to-back strength. BASS/FADER CONTROL TREBLE/BALANCI CONTROL To adjust the fader, push on the BASS/FADER control knob to get it to pop out. Pull it out slightly farther, and adjust the front-to-back sound to your liking.
Main Menu Audio System Audio System Lighting You can use the instrument panel brightness control knob to adjust the illumination of the audio system (see page 64). The audio system illuminates when the parking lights are on, even if the radio is turned off. Operating the Cassette Player Turn the audio system ON. Make sure the tape opening on the cassette is facing to the right, then insert the cassette most of the way into the slot. The system will pull it in the rest of the way, and begin to play.
Main Menu Audio System REPEAT — The Repeat function continuously replays the current song or passage. Press the RPT button to activate it; you will see RPT displayed as a reminder. When the system reaches the end of the song or passage currently playing, it will automatically go into rewind. When it senses the beginning of the same song or passage, the system returns to PLAY mode. It will continue to repeat this same program until you deactivate REPEAT by pressing the button again.
Main Menu Audio System The SKIP and REPEAT functions use silent periods on the tape to find the end of a song or passage. These features may not work to your satisfaction if there is almost no gap between selections, a high noise level between selections, or a silent period in the middle of selection. EJECT BUTTON RPT BUTTON CASSETTE SLOT REW BUTTON TAPE DIRECTION INDICATOR FF BUTTON Caring for Cassettes Damaged cassettes can jam inside the drive or cause other problems.
Main Menu Audio System Operating the Optional CD Player/Changer A Compact Disc changer is available from your dealer. It holds up to six discs, providing several hours of continuous entertainment. You operate the CD changer with the same controls used for the radio and cassette player. TAPE/CD BUTTON RANDOM INDICATOR REPEAT INDICATOR AM/FM BUTTON Your dealer also has an accessory indash single CD player available that is operated by the radio controls.
Main Menu Audio System To operate the CD changer or player, the ignition must be in ACCESSORY (I) or ON (II) and the audio system must be on. Press the CD button until "CD" appears in the display. The system will start to play the first track of the first disc in the magazine. Play only standard round discs. When that disc ends, the next disc in the magazine is loaded and played. After the last disc finishes, the system returns to disc 1.
Main Menu Audio System If the system is in Repeat mode, you must turn it off by pressing RPT before you can select Random Play. Then press the button again until you see RDM displayed. AM/FM BUTTON RANDOM INDICATOR TAPE/CD BUTTON REPEAT INDICATOR To take the system out of CD mode, press the A M / FM button or insert a cassette in the player. If a tape is already in the cassette player, press the TAPE button. When you return to CD mode, play will continue at the same disc and track.
Main Menu Audio System CD Changer Error Indications If you see an error indication in the display while operating the CD changer, find the cause in the chart to the right. If you cannot clear the error indication, take the car to your Honda dealer.
Main Menu Audio System AM/FM/CD Audio System For EX and EX-V6 models Your Honda's audio system provides clear reception on both AM and FM bands, while the preset buttons allow you to easily select your favorite stations. The anti-theft feature will disable the system if it is disconnected from the car's battery. To get the system working again, you must enter a code number (see page 156 ).
Main Menu Audio System Operating the Radio The ignition switch must be in ACCESSORY (I) or ON (II) to operate the audio system. Turn the system on by pushing the PWR/ VOL knob. Adjust the volume by turning the same knob. TUNE KNOB PWR/VOL KNOB FM BUTTON AM BUTTON The band and frequency that the radio was last tuned to is displayed. To change bands, press the AM or FM button. On the FM band, ST will be displayed if the station is broadcasting in stereo. Stereo reproduction on AM is not available.
Main Menu Audio System You can use any of four methods to find radio stations on the selected band: TUNE, SEEK, SCAN or the Preset buttons. TUNE — Use the TUNE knob to tune the radio to a desired frequency. Turn the TUNE knob to the right to tune to a higher frequency, or to the left to tune to a lower frequency. Turn the knob right or left until the display reaches the desired frequency. SEEK — The SEEK function searches the band for a station with a strong signal.
Main Menu Audio System AUTO SELECT — If you are traveling far from home and can no longer receive the stations you preset, you can use the Auto Select feature to find stations in the local area. A. SEL INDICATOR To activate Auto Select, press the A. SEL button. A. SEL will flash in the display, and the system will go into scan mode for several seconds.
Main Menu Audio System If you do not like the stations Auto Select has stored, you can store other frequencies in the preset buttons. Use the TUNE, SEEK, or SCAN function to find the desired frequencies, then store them in the selected preset buttons as described previously. TUNE KNOB Auto Select does not erase the frequencies that you preset previously. When you return home, turn off Auto Select by pressing the A. SEL button. The preset buttons will then select the frequencies you originally set.
Main Menu Audio System Adjusting the Sound Balance/Fader — These two controls adjust the strength of the sound coming from each speaker. The Balance control adjusts the sideto-side strength, while the Fader control adjusts the front-to-back strength. BASS/FADER CONTROL To adjust the fader, push on the BASS/FADER control knob to get it to pop out. Pull it out slightly farther, and adjust the front-to-back sound to your liking.
Main Menu Audio System Audio System Lighting You can use the instrument panel brightness control knob to adjust the illumination of the audio system (see page 64). The audio system illuminates when the parking lights are on, even if the radio is turned off. Stations must use these exact frequencies. It is fairly common for stations to round-off the frequency in their advertising, so your radio could display a frequency of 100.9 even though the announcer may identify the station as "FM101.
Main Menu Audio System As required by the FCC: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Radio signals, especially on the FM band, are deflected by large objects such as buildings and hills. Your radio then receives both the direct signal from the station's transmitter, and the deflected signal. This causes the sound to distort or flutter. This is a main cause of poor radio reception in city driving.
Main Menu Audio System Operating the CD Player You operate the CD player with the same controls used for the radio. PWR/VOL KNOB FM BUTTON AM BUTTON EJECT BUTTON CD SLOT REPEAT BUTTON CD BUTTON SKIP BUTTONS With the system on, insert the disc into the CD slot. Push the disc in halfway, the drive will pull it in the rest of the way and begin to play. The number of the track that is playing is shown in the display. Do not play 3-inch (8-cm) discs in this system. Play only standard round discs.
Main Menu Audio System If you turn the system off while a CD is playing, either with the PWR/VOL knob or by turning off the ignition, the disc will stay in the drive. When you turn the system back on, the CD will begin playing where it left off. Press the eject button to remove the disc from the drive. If you eject the disc, but do not remove it from the slot, the system will automatically reload the disc after 15 seconds and put the CD player in pause mode. To begin playing the disc, press the CD button.
Main Menu Audio System Operating the CD Changer (Optional) A Compact Disc changer is available for your car. It holds up to six discs, providing several hours of continuous entertainment. You operate this CD changer with the same controls used for the in-dash CD player. Load the desired CDs in the magazine and load the magazine in the changer according to the instructions that came with the unit. Play only standard round discs. Oddshaped CDs may jam in the drive or cause other problems.
Main Menu Audio System Protecting Compact Discs Handle a CD by its edges; never touch either surface. Contamination from fingerprints, liquids, felt-tip pens, and labels can cause the CD to not play properly, or possibly jam in the drive. When a CD is not being played, store it in its case to protect it from dust and other contamination. To prevent warpage, keep CDs out of direct sunlight and extreme heat. Comfort and Convenience Features To clean a disc, use a clean soft cloth.
Main Menu Audio System CD Player Error Indications If you see an error indication in the display while operating the CD player, find the cause in the chart to the right. If you cannot clear the error indication, take the car to your Honda dealer.
Main Menu Audio System CD Changer Error Indications If you see an error indication in the display while operating the CD changer, find the cause in the chart to the right. If you cannot clear the error indication, take the car to your Honda dealer.
Main Menu Audio System Operating the Cassette Player (Optional) The cassette system features Dolby B* noise reduction, automatic sensing of chromium-dioxide (CrO2) tape, and autoreverse for continuous play. FM BUTTON REW BUTTON CD/TAPE CHG BUTTON TAPE DIRECTION INDICATOR AM BUTTON FF BUTTON Make sure the tape opening on the cassette is facing to the right, then insert the cassette most of the way into the slot. The system will pull it in the rest of the way, and begin to play.
Main Menu Audio System The tape direction indicator will light to show you which side of the cassette is playing. The indicates the side you inserted facing upward is now playing. If you want to play the other side, press the PROG button. If you turn the system off while a tape is playing, either with the PWR/ VOL knob or by turning off the ignition, the cassette will remain in the drive. When you turn the system back on, the tape will begin playing where it left off.
Main Menu Audio System SKIP — The skip function allows you to find the begining of a song or passage. To skip to the beginning of a song or passage currently playing, push the button. You will see REW flashing in the display as the tape rewinds. To skip to the beginning of the next song, push the button. You will see FF flashing in the display as the tape fast forwards. When the system finds the beginning of a song or passage, it goes back to PLAY.
Main Menu Audio System Caring for the Cassette Player The cassette player picks up dirt and oxides from the tape. This contamination builds up over time and causes the sound quality to degrade. To prevent this, you should clean the player after every 30 hours of use. Your dealer has a cleaning kit available. Look at the cassette before you insert it. If the tape is loose, tighten it by turning a hub with a pencil or your finger.
Main Menu Audio System Remote Audio Controls AUDIO/CH BUTTON The top and bottom buttons adjust the volume up or down Press the proper button and hold it until the desired volume is reached, then release it. The AUDIO/CH button has three functions, depending on whether you are listening to the radio, or playing a cassette or CD. On EX-V6 model Two controls for the audio system are mounted in the steering wheel hub. These let you control basic functions without removing your hand from the wheel.
Main Menu Audio System Theft Protection On EX and EX-V6 models Your car's audio system will disable itself if it is disconnected from electrical power for any reason. To make it work again, the user must enter a specific five-digit code in the Preset buttons. Because there are hundreds of number combinations possible from five digits, making the system work without knowing the exact code is nearly impossible. You should have received a card that lists your audio system's code number and serial number.
Main Menu Security System Standard on EX and EX-V6 models Optional on LX and LX-V6 models The security system helps to protect your car and valuables from theft. The horn sounds and a combination of headlights, parking lights, side marker lights and taillights flashes if someone attempts to break into your car or remove the radio. This alarm continues for two minutes, then the system resets.
Main Menu 158
Main Menu Before Driving Before you begin driving your Honda, you should know what gasoline to use, and how to check the levels of important fluids. You also need to know how to properly store luggage or packages. The information in this section will help you. If you plan to add any accessories to your car, please read the information in this section first. Break-in Period.............................. 160 Gasoline......................................... . 160 Service Station Procedures ..........
Main Menu Table of Contents Break-in Period, Gasoline Break-in Period Help assure your car's future reliability and performance by paying extra attention to how you drive during the first 600 miles (1,000 km). During this period: Avoid full-throttle starts and rapid acceleration. Avoid hard braking. New brakes need to be broken-in by moderate use for the first 200 miles (300 km). You should follow these same recommendations with an overhauled or exchanged engine, or when the brakes are relined.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Service Station Procedures Filling the Fuel Tank Push Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. Stop the engine and keep heat, sparks, and flame away. Handle fuel only outdoors. Wipe up spills immediately. 3. Remove the fuel fill cap slowly. You may hear a hissing sound as pressure inside the tank escapes. Place the cap in the holder on the fuel fill door. 4.
Main Menu Table of Contents Service Station Procedures 5. Screw the fuel fill cap back on, tighten it until it clicks several times. If you do not properly tighten the cap, the Malfunction Indicator Lamp may come on (see page 293). Opening the Hood HOOD RELEASE HANDLE LATCH 6. Push the fuel fill door closed until it latches. 1. Shift to Park or Neutral and set the parking brake. Pull the hood release handle located under the lower left corner of the dashboard. The hood will pop up slightly.
Main Menu Table of Contents Service Station Procedures If you can open the hood without lifting the hood latch handle, or the hood latch handle moves stiffly or does not spring back as before, the mechanism should be cleaned and lubricated (see page 233). SUPPORT ROD To close the hood, lift it up slightly to remove the support rod from the hole. Put the support rod back into its holding clip. Lower the hood to about a foot (30 cm) above the fender, then let it drop.
Main Menu Table of Contents Service Station Procedures Oil Check DIPSTICK 6-cylinder models 6-cylinder models Lift the hood up most of the way. The hydraulic supports will lift it up the rest of the way and hold it up. To close the hood, lower it to about a foot (30 cm) above the fender, then press down firmly with your hands. After closing the hood, make sure it is securely latched. Before Driving 4-cylinder models Check the engine oil level every time you fill the car with fuel.
Main Menu Table of Contents Service Station Procedures 4-cylinder models 2. Wipe the dipstick with a clean cloth or paper towel. 6-cylinder models 3. Insert it all the way back in its tube.
Main Menu Table of Contents Service Station Procedures Engine Coolant Check RESERVE TANK M AX RESERVE TANK M AX UPPER MARK LOWER MARK 4-cy!inder models 4. Remove the dipstick again and check the level. It should be between the upper and lower marks. If it is near or below the lower mark, see Adding Oil on page 212 . Before Driving M IN Look at the coolant level in the radiator reserve tank. Make sure it is between the MAX and M IN lines.
Main Menu Table of Contents Fuel Economy The condition of your car and your driving habits are the two most important things that affect the fuel mileage you get. Vehicle Condition Always maintain your car according to the maintenance schedule. This will keep it in top operating condition. An important part of that maintenance is the Owner Maintenance Checks (see page 209 ). For example, an underinflated tire causes more "rolling resistance," which uses fuel.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Accessories and Modifications Modifying your car, or installing some non-Honda accessories, can make your car unsafe. Before you make any modifications or add any accessories, be sure to read the following information. Accessories Your dealer has Genuine Honda accessories that allow you to personalize your car. These accessories have been designed and approved for your car, and are covered by warranty.
Main Menu Table of Contents Accessories and Modifications Modifications Do not remove any original equipment or modify your car in any way that would alter its design or operation. This could make your car unsafe and illegal to drive. In addition, any modifications that decrease ground clearance increase the chance of undercarriage parts striking a curb, speed bump, or other raised object, which could cause your airbags to deploy.
Main Menu Table of Contents Carrying Cargo CONSOLE COMPARTMENT Your car has several convenient storage areas so you can stow cargo safely. DOOR POCKET The glove box, and the pockets in the doors and seat-backs, are designed for small, lightweight items. The trunk is intended for larger, heavier items. In addition, the back seat can be folded down to allow you to carry more cargo or longer items.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Carrying Cargo Load Limit The maximum load for your car is 850 1bs (395kg). This figure includes the total weight of all occupants, cargo, accessories, and the tongue weight if you are towing a trailer. To figure out how much cargo you can carry: Add up the weight of all occupants. If you are towing a trailer, add the tongue weight to the number above. Subtract the total from 850 Ibs (395kg).
Main Menu Table of Contents Carrying Cargo Carrying Cargo in the Trunk or on a Roof Rack Distribute cargo evenly on the floor of the trunk, placing the heaviest items on the bottom and as far forward as possible. If you fold down the back seat, tie down items that could be thrown about the car during a crash or sudden stop. If you carry large items that prevent you from closing the trunk lid, exhaust gas can enter the passenger area.
Main Menu Driving This section gives you tips on starting the engine under various conditions, and how to operate the 5-speed manual and automatic transmissions. It also includes important information on parking your car, the braking system, and facts you need if you are planning to tow a trailer. Preparing to Drive......................... 174 Starting the Engine........................ 175 Starting in Cold Weather at High Altitude ..................... 176 5-speed Manual Transmission.....
Main Menu Table of Contents Preparing to Drive You should do the following checks and adjustments every day before you drive your car. 1. Make sure all windows, mirrors, and outside lights are clean and unobstructed. Remove frost, snow, or ice. 2. Check that the hood and trunk are fully closed. 3. Visually check the tires. If a tire looks low, use a gauge to check its pressure. 4. Check that any items you may be carrying with you inside are stored properly or fastened down securely. Driving 5.
Main Menu Table of Contents Starting the Engine 1. Apply the parking brake. 2. In cold weather, turn off all electrical accessories to reduce the drain on the battery. 3. Manual Transmission: Push the clutch pedal down all the way. START (III) does not function unless the clutch pedal is depressed. Automatic Transmission: Make sure the shift lever is in Park. Press on the brake pedal. 4. Without touching the accelerator pedal, turn the ignition key to the START (III) position.
Main Menu Table of Contents Starting the Engine Starting in Cold Weather at High Altitude (Above 8,000 feet/ 2,400 meters) An engine is harder to start in cold weather. The thinner air found at high altitude above 8,000 feet (2,400 meters) adds to the problem. Use the following procedure: Driving 1. Turn off all electrical accessories to reduce the drain on the battery. 2. Push the accelerator pedal halfway to the floor and hold it there while starting the engine.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ 5-speed Manual Transmission Come to a full stop before you shift into Reverse. You can damage the transmission by trying to shift into Reverse with the car moving. Push down the clutch pedal, and pause for a few seconds before shifting into Reverse, or shift into one of the forward gears for a moment. This stops the gears so they won't "grind." The manual transmission is synchronized in all forward gears for smooth operation.
Main Menu Table of Contents 5-speed Manual Transmission, Automatic Transmission Recommended Shift Points Drive in the highest gear that lets the engine run and accelerate smoothly. This will give you the best fuel economy and effective emissions control. The following shift points are recommended: Engine Speed Limiter If you exceed the maximum speed for the gear you are in, the engine speed will enter into the tachometer's red zone. If this occurs, you may feel the engine cut in and out.
Main Menu Table of Contents Automatic Transmission Shift Lever Position Indicator The "D4" indicator comes on for a few seconds when you turn the ignition switch ON (II). If it flashes while driving (in any shift position), it indicates a possible problem in the transmission. Avoid rapid acceleration and have the transmission checked by an authorized Honda dealer as soon as possible.
Main Menu Table of Contents Automatic Transmission Park (P) — This position mechanically locks the transmission. Use Park whenever you are turning off or starting the engine. To shift out of Park, you must press on the brake pedal and have your foot off the accelerator pedal. Press the release button on the side of the shift lever to move it. If you have done all of the above and still cannot move the lever out of Park, see Shift Lock Release on page 183.
Main Menu Table of Contents Automatic Transmission Neutral (N) — Use Neutral if you need to restart a stalled engine, or if it is necessary to stop briefly with the engine idling. Shift to Park position if you need to leave the car for any reason. Press on the brake pedal when you are moving the shift lever from Neutral to another gear. Drive (D4) — Use this position for your normal driving. The transmission automatically selects a suitable gear for your speed and acceleration.
Main Menu Table of Contents Automatic Transmission First (1) — To shift from Second to First, press the release button on the side of the shift lever. With the lever in this position, the transmission locks in First gear. By upshifting and downshifting through 1, 2, D3 and D4, you can operate this transmission much like a manual transmission without a clutch pedal.
Main Menu Table of Contents Automatic Transmission If you need to use the Shift Lock Release, it means your car is developing a problem. Have the car checked by your Honda dealer. 3. Put a cloth on the edge of the Shift Lock Release slot cover next to the shift lever. Use a small flat-tipped screwdriver or small metal plate (neither are included in the tool kit) to remove the cover. Carefully pry off the edge of the cover. 4. Insert the key in the Shift Lock Release slot. 5.
Main Menu Table of Contents Parking Always use the parking brake when you park your car. The indicator on the instrument panel shows that the parking brake is not fully released; it does not indicate that the parking brake is firmly set. Make sure the parking brake is set firmly or your car may roll if it is parked on an incline. If the car is facing uphill, turn the front wheels away from the curb. If you have a manual transmission, put it in first gear.
Main Menu Table of Contents The Braking System Your Honda is equipped with front disc brakes. The brakes on the rear wheels may be disc or drum, depending on model. A power assist helps reduce the effort needed on the brake pedal. The ABS helps you retain steering control when braking very hard. Put your foot on the brake pedal only when you intend to brake. Resting your foot on the pedal keeps the brakes applied lightly, causing them to build up heat. Heat build-up can reduce how well your brakes work.
Main Menu Table of Contents The Braking System Brake System Design The hydraulic system that operates the brakes has two separate circuits. Each circuit works diagonally across the vehicle (the left-front brake is connected with the right-rear brake, etc.). If one circuit should develop a problem, you will still have braking at two wheels. Anti-lock Brakes The EX, LX-V6 and EX-V6 models have an Anti-lock Brake System (ABS) as standard equipment. It is optional on the U.S. LX model.
Main Menu Table of Contents The Braking System Important Safety Reminders ABS does not reduce the time or distance it takes to stop the car, it only helps with steering control during braking. You should always maintain a safe following distance from other vehicles. ABS will not prevent a skid that results from changing direction abruptly, such as trying to take a corner too fast or making a sudden lane change. Always drive at a safe, prudent speed for the road and weather conditions.
Main Menu Table of Contents Driving in Bad Weather Rain, tog, and snow conditions require a different driving technique because of reduced traction and visibility. Keep your car wellmaintained and exercise greater caution when you need to drive in bad weather. The cruise control should not be used in these conditions. Driving Driving Technique — Always drive slower than you would in dry weather. It takes your car longer to react, even in conditions that may seem just barely damp.
Main Menu Table of Contents Driving in Bad Weather Visibility — Being able to see clearly in all directions and being visible to other drivers are important in all weather conditions. This is more difficult in bad weather. To be seen more clearly during daylight hours, turn on your headlights. Traction — Check your tires frequently for wear and proper pressure. Both are important in preventing "hydroplaning" (loss of traction on a wet surface).
Main Menu Table of Contents Towing a Trailer Your Honda has been designed primarily to carry passengers and their cargo. You can use it to tow a trailer if you carefully observe the load limits, use the proper equipment, and follow the guidelines in this section. Load Limits Total Trailer Weight: The total weight of the trailer and everything loaded in it must not exceed 1,000 Ibs (450 kg). Towing a load that is too heavy can seriously affect your car's handling and performance.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Towing a Trailer Gross Axle Weight Rating (GAWR): The total weight of the vehicle, all occupants, all cargo, and the tongue load must not exceed: (LX) 2,160 Ibs (980 kg) (EX) 2,185 Ibs (990 kg) (LX-V6.EX-V6) 2,315 Ibs (1,050 kg) on the front axle Exceeding load limits or improperly loading your vehicle and trailer can cause a crash in which you can be seriously injured or killed.
Main Menu Table of Contents Towing a Trailer Towing Equipment and Accessories Towing can require a variety of equipment, depending on the size of your trailer, how it will be used, and how much load you are towing. Discuss your needs with your trailer sales or rental agency, and follow the guidelines in the rest of this section. Also make sure that all equipment is properly installed and that it meets federal, state, province, and local regulations.
Main Menu Table of Contents Towing a Trailer Trailer Brakes Honda recommends that any trailer having a total weight of 1,000 Ibs (450 kg) or more be equipped with its own electric or surge-type brakes. If you choose electric brakes, be sure they are electronically actuated. Do not attempt to tap into your vehicle's hydraulic system. No matter how successful it may seem, any attempt to attach trailer brakes to your vehicle's hydraulic system will lower braking effectiveness and create a potential hazard.
Main Menu Table of Contents Towing a Trailer Additional Trailer equipment Many states and provinces require special outside mirrors when towing a trailer. Even if they don't, you should install special mirrors if you cannot clearly see behind you, or if the trailer creates a blind spot. Ask your trailer sales or rental agency if any other items are recommended or required for your towing situation.
Main Menu Table of Contents Towing a Trailer Driving Safely With a Trailer The added weight, length, and height of a trailer will affect your vehicle's handling and performance, so driving with a trailer requires some special driving skills and techniques. For your safety and the safety of others, take time to practice driving maneuvers before heading for the open road, and follow the guidelines discussed below.
Main Menu Table of Contents Towing a Trailer Handling Crosswinds and Buffeting Crosswinds and air turbulence caused by passing trucks can disrupt your steering and cause trailer swaying. When being passed by a large vehicle, keep a constant speed and steer straight ahead. Do not try to make quick steering or braking corrections. Backing Up Always drive slowly and have someone guide you when backing up.
Main Menu Maintenance This section explains why it is important to keep your car well maintained and to follow basic maintenance safety precautions. This section also includes Maintenance Schedules for normal driving and severe driving conditions, a Maintenance Record, and instructions for simple maintenance tasks you may want to take care of yourself. If you have the skills and tools to perform more complex maintenance tasks on your Honda, you may want to purchase the Service Manual.
Main Menu Table of Contents Maintenance Safety Some of the most important safety Regularly maintaining your car is the This section includes instructions for precautions are given here. However, best way to protect your investment. simple maintenance tasks, such as we cannot warn you of every Proper maintenance is essential to checking ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ and adding oil.
Main Menu Table of Contents Maintenance Safety Important Safety Precautions Before you begin any maintenance, make sure your car is parked on level ground and that the parking brake is set. Also, be sure the engine is off. This will help to eliminate several potential hazards: Carbon monoxide poisoning from engine exhaust. Be sure there is adequate ventilation whenever you operate the engine. Burns from hot parts. Let the engine and exhaust system cool before touching any parts. Injury from moving parts.
Main Menu Table of Contents Maintenance Schedule The Maintenance Schedule specifies how often you should have your car serviced and what things need attention. It is essential that you have your car serviced as scheduled to retain its high level of safety, dependability, and emissions control performance. The services and time or distance intervals shown in the maintenance schedule assume you will use your car as normal transportation for passengers and their possessions.
Main Menu Table of Contents Maintenance Schedule Your authorized Honda dealer knows your car best and can provide competent, efficient service. However, service at a dealer is not mandatory to keep your warranties in effect. Maintenance may be done by any qualified service facility or person who is skilled in this type of automotive service. Keep all the receipts as proof of completion, and have the person who does the work fill out the Maintenance Record. Check your warranty booklet for more information.
Main Menu Table of Contents U.S. Owners Follow the Normal Conditions Maintenance Schedule if the severe driving conditions specified in the Severe Conditions Maintenance Schedule do not apply. NOTE: If you only OCCASIONALLY drive under a "severe" condition, you should follow the Normal Conditions Maintenance Schedule. Canadian Owners Follow the Maintenance Schedule for Severe Conditions. * 1 : Balancer belt applies to 4-cylinder models only.
Main Menu Table of Contents Service at the indicated distance or time, whichever comes first. Do the items in A, B, C as required for each distance/time interval. Follow this schedule if the severe driving conditions described in the Severe Conditions Schedule on the next page do not apply. Canadian owners: Follow the schedule for Severe Conditions. page 249 ). belt applies to 4-cylinder models only. * #1 :: Balancer See information on maintenance and emissions warranty, last column, page 201.
Main Menu Table of Contents U.S. Owners Follow the Severe Conditions Maintenance Schedule if you drive your vehicle MAINLY under one or more of the following conditions: Driving less than 5 miles (8 km) per trip or, in freezing temperatures, driving less than 10 miles (16 km) per trip. Driving in extremely hot [over 90° F (32°C] conditions. E xtensive idling or long periods of stop-and-go driving. Trailer towing, driving with a roof top carrier, or driving in mountainous conditions.
Main Menu Table of Contents Use this schedule if your vehicle is MAINLY driven in any of the following Severe Conditions, or normally driven in Canada; otherwise use the Normal Schedule. Service at the indicated distance or time, whichever comes first. Do the items in A, B, C, D as required for each distance/time. Severe Conditions: Driving less than 5 miles (8 km) per trip or, in freezing temperatures, driving less than 10 miles (16 km) per trip. Driving in extremely hot (over 90°F/32°C) conditions.
Main Menu Table of Contents Balancer belt applies to 4-cylinder models only. *21 :: Refer page 245 for replacement information under special * drivingtoconditions. Refer to page 244 for replacement information under special *3 : driving conditions. # : See information on maintenance and emissions warranty, last column, page 2 0 1. NOTE: • Check engine oil and coolant at each fuel stop. • Check and adjust valve clearance, cold engine, if noisy.
Main Menu Table of Contents Required Maintenance Record (for Normal and Severe Schedules) You or the servicing dealer can record all completed maintenance here, whether you follow the schedule for normal conditions (page 202 ) or severe conditions (page 204). Keep the receipts for all work done on your vehicle.
Main Menu Table of Contents Required Maintenance Record (for Normal and Severe Schedules) Maintenance
Main Menu Table of Contents Owner Maintenance Checks You should check the following items at the specified intervals. If you are unsure of how to perform any check, turn to the page given. Engine oil level — Check every time you fill the fuel tank. See page 164. Engine coolant level — Check the radiator reserve tank every time you fill the fuel tank. See page 166. Windshield washer fluid — Check the level in the reservoir monthly.
Main Menu Table of Contents Fluid Locations 4-cylinder Models BRAKE FLUID (Gray cap) CLUTCH FLUID (5-speed Manual Transmission only) (Gray cap) ENGINE OIL FILL CAP (Black cap) ENGINE OIL DIPSTICK (Orange loop) AUTOMATIC TRANSMISSION FLUID DIPSTICK (Yellow loop) WASHER FLUID (Blue cap) ENGINE COOLANT RESERVOIR POWER STEERING FLUID (Red cap) RADIATOR CAP Maintenance
Main Menu Table of Contents Fluid Locations 6-cylinder Models ENGINE OIL FILL CAP (Black cap) BRAKE FLUID (Gray cap) ENGINE OIL DIPSTICK (Orange loop) AUTOMATIC TRANSMISSION FLUID DIPSTICK (Yellow loop) WASHER FLUID (Blue cap) ENGINE COOLANT RESERVOIR POWER STEERING FLUID (Red cap) RADIATOR CAP Maintenance
Main Menu Table of Contents Engine Oil Adding Oil ENGINE OIL FILL GAP 4-cylinder models To add oil, unscrew and remove the engine oil fill cap on top of the valve cover. Pour in the oil, and install the engine oil fill cap. Tighten it securely. Wait a few minutes and recheck the oil level. Do not fill above the upper mark; you could damage the engine. Maintenance ENGINE OIL FILL CAP 6-cylinder models Recommended Oil Oil is a major contributor to your engine's performance and longevity.
Main Menu Table of Contents Engine Oil The API Service label also tells you the service classification of the oil. Always use an oil that is labeled "API Service SJ." This service rating may include other classifications, such as CD. These additional classifications are not a problem, as long as the label also carries the SJ classification. The oil container may also display the API Certification seal. Make sure it says "For Gasoline Engines.
Main Menu Table of Contents Engine Oil Synthetic Oil You may use a synthetic motor oil if it meets the same requirements given for conventional motor oil: energy conserving, a service classification of SJ, and the proper weight as shown on the chart. When using synthetic oil, you must follow the oil and filter change intervals given in the maintenance schedule. Additives Your Honda does not need any oil additives.
Main Menu Table of Contents Engine Oil WASHER 6-cylinder models DRAIN BOLT OIL FILTER OIL FILTER 4-cylinder models 6-cylinder models 3. Remove the oil filter and let the remaining oil drain. A special wrench (available from your Honda dealer) is required to remove the filter. 4. Install a new oil filter according to instructions that come with it.
Main Menu Table of Contents Engine Oil 5. Put a new washer on the drain bolt, then reinstall the drain bolt. Tighten it to: (LX, EX) 33 lbf.ft (44N.m,4.5kgf.m) (LX-V6, EX-V6) 29 lbf.ft (39 N.m, 4.0 kgf.m) 6. Refill the engine with the recommended oil. Engine oil change capacity (including filter): (LX, EX) 4.5 US qt (4.3 ,3.8 Imp qt) (LX-V6, EX-V6) 4.6 US qt (4.4 , 3.9 Imp qt) Maintenance 7. Replace the engine oil fill cap. Start the engine.
Main Menu Table of Contents Cooling System Adding Engine Coolant refilled with Honda antifreeze/ coolant as soon as possible. ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ If the reserve tank is completely empty, you should also check the coolant level in the radiator. 4-cylinder models RESERVE TANK If the coolant level in the reserve tank is at or below the MIN line, add coolant to bring it up to the MAX line. Inspect the cooling system for leaks.
Main Menu Table of Contents Cooling System RADIATORCAP 4-cylinder models 2. Turn the radiator cap counterclockwise, without pressing down on it, until it stops. This relieves any pressure remaining in the cooling system. 3. Remove the radiator cap by pushing down and turning counterclockwise. Maintenance 6-Cylinder models RADIATORCAP 4. The coolant level should be up to the base of the filler neck. Add coolant if it is low. 5. Put the radiator cap back on. Tighten it fully.
Main Menu Table of Contents Cooling System Replacing Engine Coolant The cooling system should be completely drained and refilled with new coolant according to the time and distance recommendations in the maintenance schedule. Only use Genuine Honda Antifreeze/Coolant. 6-cylinder models RESERVE TANK Do not add any rust inhibitors or other additives to your car's cooling system. They may not be compatible with the coolant or engine components.
Main Menu Table of Contents Cooling System DRAIN PLUG DRAIN BOLT 6-cyliner models 4-cylinder models DRAIN PLUG 3. 4-cylinder models Loosen the drain plug on the bottom of the radiator. The coolant will drain through the splash guard. Remove the drain bolt and washer from the engine block. Maintenance 6-cylinder models 6-cylinder models DRAIN BOLT Loosen the drain plug on the bottom of the radiator. The coolant will drain through the splash guard. Loosen the drain bolt.
Main Menu Table of Contents Cooling System RESERVE TANK 4-cylinder models RESERVE TANK CAP HOLDER 4. Remove the reserve tank from its holder by pulling it straight up. Drain the coolant, then put the tank back in its holder. GROUND CABLE CRUISE CONTROL CABLE RESERVE TANK 6-cylinder models RESERVE TANK CAP HOLDER 6-cylinder models When removing the reserve tank, first remove the cruise control cable and the ground cable from their clips.
Main Menu Table of Contents Cooling System 5. When the coolant stops draining, tighten the drain plug at the bottom of the radiator. 6. 4-cylinder models Put a new washer on the drain bolt, then reinstall the drain bolt in the engine block. Tighten it securely. Tightening torque: 61 lbf.ft(83N. m,8.5kgf.m) 7. Mix the recommended antifreeze with an equal amount of purified or distilled water in a clean container. The cooling system capacity is: 4-cylinder models With 5-speed manual transmission: 1.
Main Menu Table of Contents Cooling System FILLER NECK 13.Start the engine and let it run until the radiator cooling fan comes on at least twice. Then stop the engine. FILLER NECK 14.Remove the radiator cap. Pour coolant into the radiator up to the base of the filler neck and into the reserve tank up to the MAX mark. 4-cylinder models Fill up to here 9. 6-cylinder models Pour coolant into the radiator up to the base of the filler neck. Start the engine and let it run for about 30 seconds.
Main Menu Table of Contents Windshield Washers Check the level in the windshield washer reservoir at least monthly during normal usage. In bad weather, when you use the washers often, check the level every time you stop for fuel. LEVEL GAUGE LEVEL GAUGE 4-cylinder models The windshield washer reservoir is located behind the driver's side headlight. 6-cylinder models The windshield washer reservoir is located behind the passenger's side headlight.
Main Menu Table of Contents Transmission Fluid Automatic Transmission DIPSTICK UPPER MARK LOWER MARK 4-cylinder models DIPSTICK Check the fluid level with the engine at normal operating temperature. 6 cylinder models DIPSTICK 1. Park the car on level ground. Shut off the engine. 2. Remove the dipstick (yellow loop) from the transmission and wipe it with a clean cloth. 4-cylinder models 3. Insert the dipstick all the way into the transmission securely as shown in the illustration.
Main Menu Table of Contents Transmission Fluid DIPSTICK UPPER MARK LOWER MARK 6-cylinder models 4. Remove the dipstick and check the fluid level. It should be between the upper and lower marks. Maintenance 5. If the level is below the lower mark, add fluid to bring it to the upper mark. Always use Honda Premium Formula Automatic Transmission Fluid (ATF). If it is not available, you may use a DEXRON® III automatic transmission fluid as a temporary replacement.
Main Menu Table of Contents Transmission Fluid 5-speed Manual Transmission Correct level FILLER BOLT ChecK the fluid level with the transmission at normal operating temperature and the car sitting on level ground. Remove the transmission filler bolt and carefully feel inside the bolt hole with your finger. The fluid level should be up to the edge of the bolt hole. If it is not, add Genuine Honda Manual Transmission Fluid (MTF) until it starts to run out of the hole.
Main Menu Table of Contents Brake and Clutch Fluid Check the fluid level in the reservoirs monthly. There are up to two reservoirs, depending on the model. They are: Brake fluid reservoir (all models) Clutch fluid reservoir (manual transmission only) The brake fluid should be replaced according to the time and distance recommendations in the maintenance schedule. Maintenance Always use Genuine Honda DOT 3 brake fluid.
Main Menu Table of Contents Brake and Clutch Fluid Clutch System MAX M AX 6-cylinder models MIN Low fluid level can indicate a leak in the clutch system. Have this system inspected as soon as possible. M IN The fluid should be between the MIN and MAX marks on the side of the reservoir. If it is not, add brake fluid to bring it up to that level. Use the same fluid specified for the brake system.
Main Menu Table of Contents Power Steering UPPER LEVEL UPPER LEVEL A low power steering fluid level can indicate a leak in the system. Check the fluid level frequently and have the system inspected as soon as possible. NOTICE Turning the steering wheel to full left or right lock and holding it there can damage the power steering pump. 4-cylinder models LOWER LEVEL You should check the fluid level in the power steering reservoir monthly. Check the level when the engine is cold.
Main Menu Table of Contents Air Cleaner Element The air cleaner element should be cleaned or replaced according to the time and distance recommendations in the maintenance schedule. Replacement 4-cylinder Models HOLD-DOWN CLAMPS Cleaning (Severe Conditions) Clean the air cleaner element by blowing compressed air through it in the opposite direction to normal air flow. If you do not have access to compressed air (such as a service station), ask your Honda dealer to do this service.
Main Menu Table of Contents Air Cleaner Element Replacement 6-cylinder Models The air cleaner element is inside the air cleaner housing on the driver's side of the engine compartment. To replace it: BOLTS AIR CLEANER ELEMENT 1. Loosen the four bolts and remove the air cleaner housing cover. 4. Place the new air cleaner element in the air cleaner housing. 2. Remove the old air cleaner element. 5. Reinstall the air cleaner housing cover, tighten the four bolts. 3.
Main Menu Table of Contents Hood Latch, Spark Plugs (4-cylinder Models) Hood Latch LATCH ASSEMBLY PIVOTS Clean the hood latch assembly with a mild cleaner, then lubricate it with a multipurpose grease. Lubricate all the moving parts, including the pivot. To lubricate them, remove the holding clip and pull the cover away. Follow the time and distance recommendations in the Maintenance Schedule. If you are not sure how to clean and grease the latch, contact your Honda dealer.
Main Menu Table of Contents Spark Plugs (4-cylinder Models) NOTICE Tighten the spark plugs carefully. A spark plug that is too loose can overheat and damage the engine. Overtightening can cause damage to the threads in the cylinder head. 6. Install the spark plug cap. 7. Repeat this procedure for the other three spark plugs. 4. Put the new spark plug into the socket; then screw it into the hole. Screw it in by hand so you do not crossthread it. Maintenance 5. Torque the spark plug.
Main Menu Table of Contents Spark Plugs (6-cylinder Models) The spark plugs in your car should be replaced according to the time and distance recommendations in the maintenance schedule. Replacement HOLDING CLIP 1. Loosen the two holding clips by turning the heads one-quarter turn counterclockwise with a flat-tipped screwdriver. Remove the cover on the front cylinder bank by pulling it straight up. 2. Clean up any dirt and oil that have collected around the ignition coils. 3.
Main Menu Table of Contents Spark Plugs (6-cylinder Models) 4. Use a wrench to remove the hexagon socket head cap bolt holding the ignition coil. Remove the ignition coil by pulling it straight out. Maintenance 5. Remove the spark plug with a five-eighths inch (16 mm) spark plug socket. 6. Put the new spark plug into the socket; then screw it into the hole. Screw it in by hand so you do not crossthread it. 7. Torque the spark plug.
Main Menu Table of Contents Spark Plugs (6-cylinder Models) NOTICE Tighten the spark plugs carefully. A spark plug that is too loose can overheat and damage the engine. Overtightening can cause damage to the threads in the cylinder head. 8. Install the ignition coil. Reinstall the hexagon socket head cap bolt. 9. Push the wire connector onto the ignition coil. Make sure it locks in place. 10.Repeat this procedure for the other five spark plugs. 11.
Main Menu Table of Contents Battery Check the condition of your car's battery monthly. You should check the color of the test indicator window, and for corrosion on the terminals. TEST INDICATOR WINDOW TEST INDICATOR WINDOW 4-cylinder models 6-cylinder models Check the battery condition by looking at the test indicator window on the battery. The label on the battery explains the test indicator's colors. Maintenance Check the battery terminals for corrosion (a white or yellowish powder).
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Battery ０３／０７／１０ ０３／０７／１０ １６：１１：０９ １６：１１：０９ ３１Ｓ５Ａ９３０ ３１Ｓ５Ａ９３０ ００２１ ００２１ The battery gives off explosive hydrogen gas during normal operation. A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you. 4-cylinder models If the terminals are severely corroded, clean them with baking soda and water. Then use a wrench to loosen and remove the cables from the terminals.
Main Menu Table of Contents Battery On EX and EX-V6 models If your car's battery is disconnected or goes dead, the audio system will disable itself. The next time you turn on the radio you will see "Code" in the frequency display. Use the Preset buttons to enter the five-digit code (see page 156 ). Maintenance NOTICE Charging the battery with the cables connected can seriously damage your car's electronic controls. Detach the battery cables before connecting the battery to a charger.
Main Menu Table of Contents Wiper Blades Check the condition of the wiper blades at least every six months. Look for signs of cracking in the rubber, or areas that are getting hard. Replace the blades if you find these signs, or they leave streaks and unwiped areas when used. WIPER ARMS LOCK TAB To replace the blade: 1. Raise the wiper arm off the windshield. Raise the driver's side first, then the passenger's side. 2. Disconnect the blade assembly from the wiper arm by pushing in the lock tab.
Main Menu Table of Contents Wiper Blades BLADE BLADE 5. Slide the new wiper blade into the holder until the tabs lock. 6. Slide the wiper blade assembly onto the wiper arm. Make sure it locks in place. REINFORCEMENT 3. Remove the blade from its holder by grasping the tabbed end of the blade. Pull firmly until the tabs come out of the holder. Maintenance 4. Examine the new wiper blades.
Main Menu Table of Contents Air Conditioning System Your car's air conditioning is a sealed system. Any major maintenance, such as recharging, should be done by a qualified mechanic. You can do a couple of things to make sure the air conditioning works efficiently. Periodically check the engine's radiator and air conditioning condenser for leaves, insects, and dirt stuck to the front surface. These block the air flow and reduce cooling efficiency.
Main Menu Table of Contents Air Conditioning Filter, Drive Belts Air Conditioning Filter The air conditioning filter removes pollen and dust that is brought in from the outside through the heating and cooling system/climate control system. This filter should be replaced every 30,000 miles (48,000 km) under normal conditions. It should be replaced every 15,000 miles (24,000 km) if you drive primarily in urban areas that have high concentrations of soot in the air from industry and diesel-powered vehicles.
Main Menu Table of Contents Drive Belts, Timing Belt The belts should have the following "play" or deflection. 4-cylinder models Alternator belt: 0.28 — 0.35in (7.0 —9.0 mm) Power steering belt: 0.51—0.63 in (13.0 —16.0 mm) 6-cylinder models Power steering belt: 0.51— 0.65 in (13.0— 16.5mm) If you see signs of wear or looseness, have your dealer adjust or replace the belts.
Main Menu Table of Contents Tires Inflation To safely operate your car, your tires must be the proper type and size, in Keeping the tires properly inflated good condition with adequate tread, provides the best combination of and correctly inflated. The following handling, tread life and riding pages give more detailed３１Ｓ５Ａ９３０ information comfort.
Main Menu Table of Contents Tires Inspection Every time you check inflation, you should also examine the tires for damage, foreign objects, and wear. Recommended Tire Pressures for Normal Driving The following chart shows the recommended cold tire pressures for most normal driving conditions and speeds. Tire pressures for high speed driving are the same as for normal driving. The compact spare tire pressure is: 60 psi (420 kPa , 4.
Main Menu Table of Contents Tires INDICATOR LOCATION MARKS TREAD WEAR INDICATORS Your car's tires have wear indicators molded into the tread. When the tread wears down to that point, you will see a 1/2 inch (12.7 mm) wide band running across the tread. This shows there is less than 1/16 inch (1.6 mm) of tread left on the tire. A tire that is this worn gives very little traction on wet roads. You should replace the tire if you can see the tread wear indicator in three or more places around the tire.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ Tires Tire Rotation Front Front (For Non-directional (For Directional Tires and Wheels) Tires and Wheels) To help increase tire life and distribute wear more evenly, you should have the tires rotated every 7,500 miles (12,000 km). Move the tires to the positions shown in the chart each time they are rotated. When shopping for replacement tires, you may find that some tires are "directional.
Main Menu Table of Contents Tires The ABS works by comparing the speed of the wheels. When replacing tires, use the same size originally supplied with the car. Tire size and construction can affect wheel speed and may cause the system to work inconsistently. If you ever need to replace a wheel, make sure the wheel's specifications match those of the original wheel that came on your car. Replacement wheels are available at your Honda dealer.
Main Menu Table of Contents Tires Snow Tires If you mount snow tires on your Honda, make sure they are radial tires of the same size and load range as the original tires. Mount snow tires on all four wheels to balance your car's handling in all weather conditions. Keep in mind the traction provided by snow tires on dry roads may not be as high as your car's original equipment tires. You should drive cautiously even when the roads are clear. Check with the tire dealer for maximum speed recommendations.
Main Menu Table of Contents Lights Check the operation of your car's exterior lights at least once a month. A burned out bulb can create an unsafe condition by reducing your car's visibility and the ability to signal your intentions to other drivers.
Main Menu Table of Contents Lights TURN SIGNAL/TAILLIGHT HIGH-MOUNT BRAKE LIGHT LICENSE PLATE LIGHT REAR SIDE MARKER LIGHT STOP/TAILLIGHT Check the following: Headlights (low and high beam) Parking lights Taillights Brake lights High-mount brake light Turn signals Back-up lights Hazard light function License plate light Side marker lights Daytime running lights (Canadian models) If you find any bulbs are burned out, replace them as soon as possible.
Main Menu Table of Contents Lights Headlight Aiming The headlights were properly aimed when your car was new. You should check their aim if you regularly carry heavy items in the trunk or pull a trailer. Each headlight assembly has horizontal and vertical adjustment indicators. These are set to their standard positions after the headlights are aimed at the factory. HORIZONTAL ANGLE GAUGE VERTICAL ANGLE GAUGE To check these settings: 1. Make sure the fuel tank is full. Park the vehicle on level ground.
Main Menu Table of Contents Lights HORIZONTAL ADJUSTMENT 6. If either indicator is not aligned with its mark as described, an adjustment can be made using a Phillips-head screwdriver to realign it with the mark. Please refer to the illustrations. VERTICAL ADJUSTMENT 7. If you cannot get the indicator to align, have your Honda dealer inspect the car for body damage or suspension problems. Replacing a Headlight Bulb Your car has two bulbs on each side, four in total.
Main Menu Table of Contents Lights AIR INTAKE DUCT BULB 5. Push the electrical connector back onto the bulb. Make sure it is on all the way. 6. Turn on the headlights to test the new bulb. 7. 4-cylinder models (Passenger's side) Reinstall the radiator reserve tank and the air intake duct. 4-cylinder models 1. Open the hood. 4-cylinder models If you need to change the headlight bulb on the passenger's side, remove the radiator reserve tank and the air intake duct.
Main Menu Table of Contents Lights Replacing Front Turn Signal and Side Marker Light Bulbs 5. Remove the burned out bulb from the socket by pushing it in and turning counterclockwise until it unlocks. HOLDING CLIP 6. Install the new bulb in the socket. Turn it clockwise to lock it in place. 7. Insert the socket back into the headlight assembly. Turn it clockwise to lock it in place. 8. Test the lights to make sure the new bulb is working. 1.
Main Menu Table of Contents Lights 3. Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms. Replacing a Parking Light Bulb POWER STEERING FLUID TANK 4. Insert the socket back into the headlight assembly. Turn it clockwise to lock it in place. 5. Turn on the parking lights to make sure the new bulb works. HOLDER 1. Open the hood. The front parking light is next to the headlight bulb.
Main Menu Table of Contents Lights Replacing Rear Bulbs (in Fenders) 4. Remove the socket by turning it one-quarter turn counterclockwise. 5. Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms. 6. Reinstall the socket into the light assembly by turning it clockwise until it locks. 7. Test the lights to make sure the new bulb is working. FASTENER 1. Open the trunk. 2.
Main Menu Table of Contents Lights 9. Put the fastener in the hole on the side of the trunk lining and push on the center until it locks (the center is flush with the head). Replacing Rear Bulbs (in Trunk Lid) SCREW 1. Open the trunk. 2. Remove the screw securing the plastic cover. Then remove the plastic cover. Maintenance 3. Determine which of the two bulbs is burned out: stop/taillight or back-up light.
Main Menu Table of Contents Lights 4. Remove the socket by turning it one-quarter turn counterclockwise. Replacing a Rear Side Marker Light Bulb 5. Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms. 6. Reinstall the socket into the light assembly. 7. Test the lights to make sure the new bulb is working. 8. Reinstall the plastic cover and secure it with the screw. SCREW 1.
Main Menu Table of Contents Lights 5. Insert the socket in the assembly. Turn it clockwise to lock it in place. Replacing a High-mount Brake Light Bulb 6. Reinstall the side marker assembly in the bumper. Tighten the mounting screw securely. 1. Open the trunk and remove the socket from the light assembly by turning it one-quarter turn counterclockwise. 2. Remove the burned-out bulb by pulling it straight out of the socket. Maintenance 3. Install the new bulb and reinstall the socket.
Main Menu Table of Contents Lights Replacing a Rear License Bulb 4. Turn on the parking lights and check that the new bulb is working. 5. Put the license light assembly in place. Tighten the two screws securely. 1. Use a Phillips-head screwdriver to loosen the two screws holding the license plate light assembly to the bracket. Slide the assembly out from the bracket. 2. Remove the socket from the light assembly by turning it one-quarter turn counterclockwise. 3.
Main Menu Table of Contents Lights Replacing Bulbs in the Interior Courtesy Lights The ceiling light, door light and vanity mirror light come apart the same way. They do not all use the same bulb. 1. Remove the lens by carefully prying on the edge of the lens with a fingernail file or a small flat-tip screwdriver. Do not pry on the edge of the housing around the lens. Maintenance CEILING LIGHT Ceiling light: Pry on the front edge of the lens near both sides.
Main Menu Table of Contents Lights VANITY MIRROR LIGHT SPOTLIGHT Replacing the Trunk Light Bulb TRUNK LIGHT LENS Spotlights: Pry on the front edge in front of both spotlights. 2. Remove the bulb by pulling it straight out of its metal tabs. 3. Push the new bulb into the metal tabs. Snap the lens back in place. 1. Open the trunk. Pull down the trunk light cover. 2. Remove the bulb by pulling it straight out of its metal tabs. 3. Push the new bulb into the metal tabs. 4. Push the cover back in place.
Main Menu Table of Contents Storing Your Car If you need to park your car for an extended period (more than one month), there are several things you should do to prepare it for storage. Proper preparation helps prevent deterioration and makes it easier to get your car back on the road. If possible, store your car indoors. Fill the fuel tank. Change the engine oil and filter (see page 214). Wash and dry the exterior completely. Clean the interior. Make sure the carpeting, floor mats, etc.
Main Menu Appearance Care Regular cleaning and polishing of your Honda helps to keep it "new" looking. This section gives you hints on how to clean your car and preserve its appearance: the paint, brightwork, wheels and interior. Also included are several things you can do to help prevent corrosion. Exterior Care.................................. 268 Washing...................................... 268 Waxing........................................ 269 Aluminum Wheels..................... 269 Paint Touch-up.
Main Menu Table of Contents Exterior Care Washing Frequent washing helps preserve your car's beauty. Dirt and grit can scratch the paint, while tree sap and bird droppings can permanently ruin the finish. Wash your car in a shady area, not in direct sunlight. If the car is parked in the sun, move it into the shade and let the exterior cool down before you start. Only use the solvents and cleaners recommended in this Owner's Manual.
Main Menu Table of Contents Exterior Care Waxing Always wash and dry the whole car before waxing it. You should wax your car, including the metal trim, whenever water sits on the surface in large patches. It should form into beads or droplets after waxing. You should use a quality liquid or paste wax. Apply it according to the instructions on the container. In general, there are two types of products: Waxes — A wax coats the finish and protects it from damage by exposure to sunlight, air pollution, etc.
Main Menu Table of Contents Interior Care Carpeting Vacuum the carpeting frequently to remove dirt. Ground-in dirt will make the carpet wear out faster. Periodically shampoo the carpet to keep it looking new. Use one of the foam-type carpet cleaners on the market. Follow the instructions that come with the cleaner, applying it with a sponge or soft brush. Keep the carpeting as dry as possible by not adding water to the foam. Fabric Vacuum dirt and dust out of the material frequently.
Main Menu Table of Contents Interior Care Seat Belts LOOP If your seat belts get dirty, you can use a soft brush with a mixture of mild soap and warm water to clean them. Do not use bleach, dye, or cleaning solvents. They can weaken the belt material. Let the belts airdry before you use the car. Dirt build-up in the loops of the seat belt anchors can cause the belts to retract slowly. Wipe the insides of the loops with a clean cloth dampened in mild soap and warm water or isopropyl alcohol.
Main Menu Table of Contents Corrosion Protection Two factors normally contribute to causing corrosion in your car: 1. Moisture trapped in body cavities. Dirt and road salt that collects in hollows on the underside of the car stays damp, promoting corrosion in that area. 2. Removal of paint and protective coatings from the exterior and underside of the car. Many corrosion-preventive measures are built into your Honda.
Main Menu Table of Contents Body Repairs Body repairs can affect your car's resistance to corrosion. If your car needs repairs after a collision, pay close attention to the parts used in the repair and the quality of the work. Make sure the repair facility uses Genuine Honda replacement body parts. Some companies make sheet metal pieces that seem to duplicate the original Honda body parts, but are actually inferior in fit, finish, and corrosion resistance.
Main Menu 274
Main Menu Taking Care of the Unexpected This section covers the morecommon problems that motorists experience with their vehicles. It gives you information about how to safely evaluate the problem and what to do to correct it. If the problem has stranded you on the side of the road, you may be able to get going again. If not, you will also find instructions on getting your car towed. Compact Spare Tire....................... 276 Changing a Flat Tire .................... 277 If Your Engine Won't Start.....
Main Menu Table of Contents Compact Spare Tire Your car has a compact spare tire that takes up less space. Use this spare tire as a temporary replacement only. Get your regular tire repaired or replaced and put back on your car as soon as you can. Check the inflation pressure of the compact spare tire every time you check the other tires. It should be inflated to: 60 psi (420 kPa , 4.
Main Menu Table of Contents Changing a Flat Tire If you have a flat tire while driving, TRUNK stop in a safe place to change it. Stopping in traffic or on the shoulder ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ of a busy road is dangerous. Drive slowly along the shoulder until you get to an exit or an area to stop that is far away from the traffic lanes. The car can easily roil off the jack, seriously injuring anyone underneath.
Main Menu Table of Contents Changing a Flat Tire WHEEL NUTS JACK WHEEL WRENCH 7. Turn the jack's end bracket counterclockwise to loosen it, then remove the jack. Taking Care of the Unexpected 8. Loosen the four wheel nuts (4cylinder) or five (V-6) 1/2 turn with the wheel wrench. JACKING POINT 9. Find the jacking point nearest the wheel you are removing. Place the jack under the jacking point. Turn the end bracket clockwise until the top of the jack contacts the jacking point.
Main Menu Table of Contents Changing a Flat Tire EXTENSION WHEEL COVER WHEEL WRENCH 10.Use the extension and wheel wrench as shown to raise the vehicle until the flat tire is off the ground. WHEEL NUTS 11.Remove the wheel nuts and flat tire. Temporarily place the flat tire on the ground with the outside surface of the wheel facing up. You could scratch the wheel if you put it face down. On LX and LX-V6 models Do not attempt to forcibly pry the wheel cover off with a screwdriver or other tool.
Main Menu Table of Contents Changing a Flat Tire BRAKE HUB 12.Before mounting the spare tire, wipe any dirt off the mounting surface of the wheel and hub with a clean cloth. Wipe the hub carefully, it may be hot from driving. Taking Care of the Unexpected 13.Put on the spare tire. Put the wheel nuts back on finger-tight, then tighten them in a crisscross pattern with the wheel wrench until the wheel is firmly against the hub. Do not try to tighten them fully. 14.
Main Menu Table of Contents Changing a Flat Tire 4-cylinder models 15.Tighten the wheel nuts securely in the same crisscross pattern. Have the wheel nut torque checked at the nearest automotive service facility. Tighten the wheel nuts to: 80 lbf.ft (108 N. m,11 kgf.m) 6-cylinder models CENTER CAP 16. On EX and EX-V6 models Remove the center cap before storing the flat tire in the trunk well.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Changing a Flat Tire WING BOLT SPACER CONE 20.Store the jack in its holder. Turn the jack's end bracket to lock it in place. Replace the cover. Store the tools. Loose items can fly around the interior in a crash and could seriously injure the occupants. Store the wheel, jack and tools securely before driving. 17.Place the flat tire face down in the spare tire well. 18.
Main Menu Table of Contents If Your Engine Won't Start Diagnosing why your engine won't start falls into two areas, depending on what you hear when you turn the key to START (III): You hear nothing, or almost nothing. The engine's starter motor does not operate at all, or operates very slowly. You can hear the starter motor operating normally, or the starter motor sounds like it is spinning faster than normal, but the engine does not start up and run.
Main Menu Table of Contents If Your Engine Won't Start Turn the ignition switch to START (III). If the headlights do not dim, check the condition of the fuses. If the fuses are OK, there is probably something wrong with the electrical circuit for the ignition switch or starter motor. You will need a qualified technician to determine the problem. (See Emergency Towing on page 301.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Jump Starting If your car's battery has run down, you may be able to start the engine by using a booster battery. Although this seems like a simple procedure, you should take several precautions. A battery can explode if you do not follow the correct procedure, seriously injuring anyone nearby. Keep all sparks, open flames, and smoking materials away from the battery.
Main Menu Table of Contents Jump Starting 4-cylinder models 3. Connect one jumper cable to the positive ( + ) terminal on the booster battery. Connect the other end to the positive ( + ) terminal on your Honda's battery. Taking Care of the Unexpected 6-cylinder models 4-cylinder models 4. Connect the second jumper cable to the negative ( — ) terminal on the booster battery. Connect the other end to the grounding strap as shown. Do not connect this jumper cable to any other part of the engine.
Main Menu Table of Contents Jump Starting 5. If the booster battery is in another vehicle, have an assistant start that vehicle and run it at a fast idle. 6. Start your car. If the starter motor still operates slowly, check the jumper cable connections to make sure they have good metal-tometal contact. 7. Once your car is running, disconnect the negative cable from your car, then from the booster battery. Disconnect the positive cable from your car, then the booster battery.
０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Main Menu Table of Contents If Your Engine Overheats 1. Safely pull to the side of the road. The pointer of your car's temperaYour car can overheat for several Put the transmission in Neutral or ture gauge should stay in the midreasons, such as lack of coolant or a Park and set the parking brake. range under most conditions. It may mechanical problem.
Main Menu Table of Contents If Your Engine Overheats 3. If you do not see steam or spray, leave the engine running and watch the temperature gauge. If the high heat is due to overloading (climbing a long, steep hill on a hot day with the A/C running, for example), the engine should start to cool down almost immediately. If it does, wait until the temperature gauge comes down to the midpoint then continue driving. 8. If there was no coolant in the 5.
Main Menu Table of Contents If Your Engine Overheats 9. Using gloves or a large heavy cloth, turn the radiator cap counterclockwise, without pushing down, to the first stop. This releases any remaining pressure in the cooling system. After the pressure releases, push down on the cap and turn it until it comes off. Taking Care of the Unexpected 10.Start the engine and set the temperature control dial to maximum (climate control to FULL AUTO at 90° F/32° C).
Main Menu Table of Contents Low Oil Pressure Indicator LOW OIL PRESSURE INDICATOR NOTICE Running the engine with low oil pressure can cause serious mechanical damage almost immediately. Turn off the engine as soon as you can safely get the car stopped. 1. Safely pull off the road and shut off the engine. Turn on the hazard warning indicators. This indicator should light when the ignition switch is ON (II), and go out after the engine starts. It should never come on when the engine is running.
Main Menu Table of Contents Charging System Indicator Immediately turn off all electrical accessories: radio, heater, A/C, climate control, rear defogger, cruise control, etc. Try not to use other electrically-operated controls such as the power windows. Keep the engine running and take extra care not to stall it. Starting the engine will discharge the battery rapidly. CHARGING SYSTEM INDICATOR This indicator should come on when the ignition switch is ON (II), and go out after the engine starts.
Main Menu Table of Contents Malfunction Indicator Lamp MALFUNCTION INDICATOR LAMP This indicator comes on for a few seconds when you turn the ignition switch ON (II). If it comes on at any other time, it indicates one of the engine's emissions control systems may have a problem. Even though you may feel no difference in your car's performance, it can reduce your fuel economy and cause your car to put out excessive emissions. Continued operation may cause serious damage.
Main Menu Table of Contents Brake System Indicator BRAKE SYSTEM INDICATOR* * U.S. indicator shown The Brake System Indicator light comes on when you turn the ignition ON (II). If the parking brake is not set, it goes off after you start the engine. If the parking brake is set, it goes off when you fully release the parking brake with the engine running. Taking Care of the Unexpected If it comes on at any other time, it indicates a problem with the car's brake system.
Main Menu Table of Contents Closing the Moonroof If the electric motor will not close the moonroof, do the following: ROUND PLUG SOCKET 1. Check the fuse for the moonroof motor (see page 296). If the fuse is blown, replace it with one of the same or lower rating. 2. Try closing the moonroof. If the new fuse blows immediately or the moonroof motor still does not operate, you can close the moonroof manually. 3. Get the moonroof wrench out of the tool kit in the trunk. 4.
Main Menu Table of Contents Fuses All the electrical circuits in your car have fuses to protect them from a short circuit or overload. These fuses are located in three fuse boxes. INTERIOR UNDER-HOOD TAB COVER The interior fuse boxes are located on each side of the dashboard. To open an interior fuse box, open the car door. Pull the cover open, then take it out of its hinges by pulling it toward you.
Main Menu Table of Contents Fuses Checking and Replacing Fuses If something electrical in your car stops working, the first thing you should check for is a blown fuse. Determine from the chart on pages 299 and 300, or the diagram on the fuse box lid, which fuse or fuses control that component. Check those fuses first, but check all the fuses before deciding that a blown fuse is not the cause. Replace any blown fuses and check the component's operation. 1. Turn the ignition switch to LOCK (0).
Main Menu Table of Contents Fuses BLOWN 5. Look for a burned wire inside the fuse. If it is burned, replace it with one of the spare fuses of the same rating or lower. If you cannot drive the car without fixing the problem, and you do not have a spare fuse, take a fuse of the same rating or a lower rating from one of the other circuits. Make sure you can do without that circuit temporarily (such as the accessory power socket or radio).
Main Menu Table of Contents Fuses INTERIOR FUSE BOX Driver's Side Passenger's Side Front Front * : On Canadian models * 1 : EX, EX-V6 * 2 : LX-V6, EX, EX-V6 * 3 : Canadian models * 4 : U.S.
Main Menu Table of Contents Fuses UNDER-HOOD FUSE BOX * 1: EX-V6 in Canada * 2 : EX, EX-V6 Taking Care of the Unexpected
Main Menu Table of Contents Emergency Towing If your car needs to be towed, call a professional towing service or, if you belong to one, an organization that provides roadside assistance. Never tow your car behind another vehicle with just a rope or chain. It is very dangerous. There are three popular types of professional towing equipment. Flat-bed Equipment — The operator loads your car on the back of a truck. This is the best way to transport your Honda.
Main Menu Table of Contents Emergency Towing If you decide to tow your car with all four wheels on the ground, make sure you use a properly-designed and attached tow bar. Prepare the car for towing as described above, and leave the ignition switch in Accessory (I) so the steering wheel does not lock. Make sure the radio and any items plugged into the accessory power socket are turned off so they do not run down the battery. NOTICE The steering wheel system can be damaged if the steering wheel is locked.
Main Menu Technical Information The diagrams in this section give you the dimensions and capacities of your Honda, and the locations of the identification numbers. The explanations of several electronic and mechanical systems on your Honda are for the more technically-oriented owner. Identification Numbers................. 304 Specifications (4-cylinder Models)................... 306 Specifications (6-cylinder Models)................... 308 DOT Tire Quality Grading (U.S. Cars).............................
Main Menu Table of Contents Identification Numbers Your car has several identifying numbers located in various places. VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is the 17-digit number your Honda dealer uses to register your car for warranty purposes. It is also necessary for licensing and insuring your car. The easiest place to find the VIN is on a plate fastened to the top of the dashboard. You can see it by looking through the windshield on the driver's side.
Main Menu Table of Contents Identification Numbers The Engine Number is stamped into the engine block. It is on the front. 4 cylinder Models AUTOMATIC TRANSMISSION NUMBER The Transmission Number is on a label on top of the transmission.
Main Menu Table of Contents * 1 : Including the coolant in the reserve tank and that remaining in the engine. Reserve tank capacity: 0.16 US gal (0.6 , 0.13 Imp gal) * 2 : Excluding the oil remaining in the engine.
Main Menu Table of Contents Specifications (4-cylinder Models) page 234.
Main Menu Table of Contents Specifications (6-cylinder Models) *1 : Including the coolant in the reserve tank and that remaining in the engine. Reserve tank capacity: 0.16 US gal (0.6 ,0.13 Imp gal) * 2 : Excluding the oil remaining in the engine.
Main Menu Table of Contents Specifications (6-cylinder Models) page 237.
Main Menu Table of Contents DOT Tire Quality Grading (U.S. Cars) The tires on your vehicle meet all U.S. Federal Safety Requirements. A ll tires are also graded for tread wear, traction, and temperature performance according to Department of Transportation (DOT) standards. The following explains these gradings. Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between the tread shoulder and the maximum section width.
Main Menu Table of Contents DOT Tire Quality Grading (U.S. Cars) Temperature The temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Main Menu Table of Contents Oxygenated Fuels Some conventional gasolines are being blended with alcohol or an ether compound. These gasolines are collectively referred to as oxygenated fuels. To meet clean air standards, some areas of the United States and Canada use oxygenated fuels to help reduce emissions. If you use an oxygenated fuel, be sure it is unleaded and meets the minimum octane rating requirement. Before using an oxygenated fuel, try to confirm the fuel's contents.
Main Menu Table of Contents Driving in Foreign Countries If you are planning to take your Honda outside the U.S. or Canada, contact the tourist bureaus in the areas you will be traveling in to find out about the availability of unleaded gasoline with the proper octane rating. If unleaded gasoline is not available, be aware that using leaded gasoline in your Honda will affect performance and fuel mileage, and damage its emissions controls. It will no longer comply with U.S.
Main Menu Table of Contents Emissions Controls The burning of gasoline in your car's engine produces several byproducts. Some of these are carbon monoxide (CO), oxides of nitrogen (NOx) and hydrocarbons (HC). Gasoline evaporating from the tank also produces hydrocarbons. Controlling the production of NOx, CO, and HC is important to the environment. Under certain conditions of sunlight and climate, NOx and HC react to form photochemical "smog.
Main Menu Table of Contents Emissions Controls Exhaust Emissions Controls The exhaust emissions controls include four systems: PGM-FI, Ignition Timing Control, Exhaust Gas Recirculation and Three Way Catalytic Converter. These four systems work together to control the engine's combustion and minimize the amount of HC, CO, and NOx that comes out the tailpipe. The exhaust emissions control systems are separate from the crankcase and evaporative emissions control systems.
Main Menu Table of Contents Three Way Catalytic Converter Keep the engine tuned-up. The three way catalytic converter contains precious metals that serve as catalysts, promoting chemical reactions to convert the exhaust gasses without affecting the metals. The catalytic converter is referred to as a three-way catalyst, since it acts on HC, CO, and NOx. A replacement unit must be an original Honda part or its equivalent.
Main Menu Warranty and Customer Relations Customer Relations Information................................. 318 U.S. Zone Office Map.................... 319 Canada Zone Office Map.............. 320 Warranty Coverages..................... 321 Reporting Safety Defects (U.S. Vehicles)........................... 322 Authorized Manuals......................
Main Menu Table of Contents Customer Relations Information Honda dealership personnel are trained professionals. They should be able to answer all your questions. If you encounter a problem that your dealership does not solve to your satisfaction, please discuss it with the dealership's management. The Service Manager or General Manager can help. Almost all problems are solved in this way.
Main Menu Table of Contents U.S. Zone Office Map Mid-Atlantic Zone 902 Wind River Ln., Suite 200 Gaithersburg, Maryland 20878 (301) 990-2020 Western Zone P.O. Box 2260 700 Van Ness Avenue Torrance, California 90509-2260 (310) 781-4565 Northwestern Zone P.O. Box20186 12439 N.E.
Main Menu Table of Contents Canada Zone Office Map CUSTOMER RELATIONS RELATIONS AVEC LA CLIENTELE Honda Canada Inc. 715 Milner Avenue Toronto, ON M1B 2K8 Tel: 1-888-9-HONDA-9 Fax: Toll-free 1-877-939-0909 Toronto (416) 287-4776 Honda Canada Inc.
Main Menu Table of Contents Warranty Coverages U.S. Owners Your new Honda is covered by these warranties: New Car Limited Warranty — covers your new vehicle, except for the battery, emissions control systems and accessories, against defects in materials and workmanship. Emissions Control Systems Defects Warranty and Emissions Performance Warranty — these two warranties cover your vehicle's emissions control systems.
Main Menu Table of Contents Reporting Safety Defects (U.S. Vehicles) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying American Honda Motor Co., Inc.
Main Menu Table of Contents Authorized Manuals Purchasing Factory Authorized Manuals (U.S. only) The following publications covering the operation and servicing of your vehicle can be obtained from Helm Incorporated, either by filling out the attached form or, for credit card holders, calling the toll-free phone number on the form. For manuals prior to the year shown below, contact Helm Incorporated, P.O. Box 07280, Detroit, Michigan 48207, or call 1-800-782-4356. Valid only for sales within the U.S.
Main Menu Table of Contents Authorized Manuals Service Manual: This manual covers maintenance and recommended procedures for repair to engine and chassis components. It is written for the Journeyman mechanic, but is simple enough for most mechanically-inclined owners to understand. Electrical Troubleshooting Manual: This manual complements the Service Manual by providing in-depth troubleshooting information for each electrical circuit in your vehicle.
Main Menu Index Accessories and Modifications.... 168 Accessories................................. 168 Additional Safety Precaution.... 169 Modifications............................. 169 ACCESSORY (Ignition Key Position).......................................76 Accessory Power Socket.............. 105 Adding Automatic Transmission Fluid........................................ 225 Brake Fluid................................. 228 Clutch Fluid................................ 229 Engine Coolant...............
Main Menu Index Battery Charging System Indicator............................ 54, 292 Jump Starting............................. 285 Maintenance............................... 238 Specifications..................... 307, 309 Before Driving............................... 159 Belts, Seat..................................... 8, 40 Beverage Holder............................ 102 Body Repair.................................... 273 Brakes Anti-lock System (ABS)............ 186 Break-in, New Linings ............
Main Menu Index Checklist, Before Driving............. 174 Child Safety...................................... 20 Cleaner Element, Air..................... 231 Cleaning Aluminum Wheels..................... 269 Carpeting....................................270 Exterior....................................... 262 Fabric.......................................... 270 Interior........................................270 Leather....................................... . 270 Seat Belts.................................
Main Menu Index Emergencies on the Road Brake System Indicator............ 294 Changing a Flat Tire................. 277 Charging System Indicator...... 292 Checking the Fuses................... 296 Low Oil Pressure Indicator...... 291 Malfunction Indicator Lamp.... 293 Manually Closing Moonroof.... 295 Overheated Engine................... 288 Emergency Brake.......................... 100 Emergency Flashers....................... 66 Emissions Controls........................
Main Menu Index Gas Station Procedures................. 161 Gauges Engine Coolant Temperature .... 59 Fuel...............................................59 Gearshift Lever Positions Automatic Transmission........... 179 5-speed Manual Transmission.......................... 177 Glass Cleaning............................... 271 Glove Box......................................... 82 Halogen Headlight Bulbs.............. 255 Hazard Warning Flashers............... 66 Headlights..................................
Main Menu Index Lights Bulb Replacement..................... 255 Indicator....................................... . 53 Parking......................................... . 62 Turn Signal................................... 64 Load Limit...................................... 171 LOCK (Ignition Key Position)....... 75 Lockout Prevention......................... 77 Locks Anti-theft Steering Column........ 75 Fuel Fill Door............................. 161 Glove Box.....................................
Main Menu Index Polishing and Waxing................... 269 Power Door Locks................................... 76 Mirrors......................................... . 99 Seats..............................................89 Steering....................................... 230 Windows.......................................96 Pre-Drive Safety Checklist............. 11 Pregnancy, Using Seat Belts.......... 18 Proper Seat Belt Usage................... 15 Protecting Adults.............................
Main Menu Index Seat Belts Tether Attachment Points.......... 39 Use During Pregnancy................ 18 Wearing a Lap/Shoulder Belt.... 15 Seats, Adjusting the......................... 87 Seat Heaters..................................... 95 Security System............................. 157 Serial Number................................ 304 Service Intervals............................ 202 Service Manual* ............................ 323 Service Station Procedures.......... 161 Setting the Clock.............
Main Menu Index Theft Protection............................. 156 Three Way Catalytic Converter... 316 Time, Setting the........................... 101 Timing Belt..................................... 245 Tire Chains..................................... 251 Tire, How to Change a Flat.......... 277 Tires............................................... . 246 Air Pressure............................... 246 Checking Wear.......................... 247 Compact Spare...........................
Main Menu Index Washer, Windshield Operation...................................... 66 Washing......................................... . 268 Waxing and Polishing................... 269 Wheels Adjusting the Steering................ 68 Alignment and Balance............. 248 Compact Spare........................... 276 Wrench....................................... 277 Windows Cleaning...................................... 271 Operating the Power................... 96 Rear, Defogger............................
Main Menu Service Information Summary Gasoline: Unleaded gasoline, pump octane number of 86 or higher. Fuel Tank Capacity: 17.12 US gal (64.8 l,14.26 Imp gal) Recommended Engine Oil: API Service SJ "Energy Conserving" oil, SAE 5W-30 viscosity (see page 212). Oil change capacity (including filter): LX, EX 4.5 US qt (4.3 l, 3.8 Imp qt) LX-V6, EX-V6 4.6 US qt (4.4 l, 3.
