2000 Civic Sedan Online Reference Owner's Manual Use these links (and links throughout this manual) to navigate through this reference. For a printed owner's manual, click on authorized manuals or go to www.helminc.com. If you have a Civic refer to Civic Sedan GX Owner’s Manual Supplement for additional information. Contents Owner's Identification Form Introduction .........................................................................................................................................
Owner's Identification OWNER Main Menu This Owner's Manual should be considered a permanent part of the car, and should remain with the car when it is sold. ADDRESS STREET CITY STATE/PROVINCE V. I. N. DELIVERY DATE (Date sold to original retail purchaser) DEALER NAME ADDRESS ZIP CODE / POSTAL CODE DEALER NO.
Main Menu Introduction Congratulations ! Your selection of a 2000 Honda Civic was a wise investment. It will give you years of driving pleasure. One of the best ways to enhance the enjoyment of your new Honda is to read this manual. In it, you will learn how to operate its driving controls and convenience items. Afterwards, keep this owner's manual in your car so you can refer to it at any time. Several warranties protect your new Honda.
31SDP610 0003 ▲ Main Menu ▼ 03/07/26 19:00:40 Main Menu A A Few Few Words Words About About Safety Safety Your safety, safety, and and the the safety safety of of others, others, Your is very very important. important. And And operating operating this this is car safely is an important vehicle safely is an important responsibility. responsibility.
Main Menu Your Car at a Glance MIRROR CONTROLS (P.84 ) HEATING/COOLING CONTROLS (P.90 ) AUDIO SYSTEM (P.98. 107. 121 ) DIGITAL CLOCK (P.101, 112, 126 ) POWER DOOR LOCK SWITCH (P.72 ) POWER WINDOW SWITCHES (P.81 ) FUEL FILL DOOR RELEASE (P.143 ) TRUNK RELEASE HANDLE (P.76 ) HOOD RELEASE HANDLE (P.
Main Menu Your Car at a Glance INSTRUMENT PANEL BRIGHTNESS (P.62 ) HAZARD WARNING LIGHTS (P.64 ) CRUISE CONTROL (P.66 ) WINDSHIELD WIPERS/WASHERS (P.63 ) MOONROOF (P.83 ) REAR WINDOW DEFOGGER (P.64 ) MIRROR CONTROLS (P.84 ) HEADLIGHTS/TURN SIGNALS (P.61, 62 ) TILT ADJUSTMENT (P.
Main Menu 4
Main Menu Driver and Passenger Safety This section gives you important information about how to protect yourself and your passengers. It shows you how to use seat belts properly. It explains your Supplemental Restraint System. And it tells you how to properly restrain infants and children in your car. Important Safety Precautions.......... 6 Your Car's Safety Features.............. 7 Seat Belts........................................ 8 Airbags........................................... .
Main Menu Table of Contents Important Safety Precautions You'll find many safety recommendations throughout this section, and throughout this manual. The recommendations on this page are the ones we consider to be the most important. Always Wear Your Seat Belt A seat belt is your best protection in all types of collisions. Airbags supplement seat belts, but airbags are designed to inflate only in a moderate to severe frontal collision.
Main Menu Table of Contents Your Car's Safety Features Your car is equipped with many features that work together to protect you and your passengers during a crash. Some safety features do not require any action on your part. These include a strong steel framework that forms a safety cage around the passenger compartment; front and rear crush zones that are designed to crumple and absorb energy during a crash; and a collapsible steering column.
Main Menu Table of Contents Your Car's Safety Features 03/07/10 Seat Belts For your safety, and the safety of your passengers, your car is equipped with seat belts in all seating positions. Your seat belt system also includes a light on the instrument panel to remind you and your passengers to fasten your seat belts. Why Wear Seat Belts Seat belts are the single most effective safety device for adults and larger children. (Infants and smaller children must be properly restrained in child seats.
Main Menu Table of Contents Your Car's Safety Features Airbags The most important things you need to know about your airbags are: Airbags do not replace seat belts. The seat belts are the occupants' primary protection in all types of collisions. The airbags supplement the seat belts by providing extra protection for the head and chest of each front seat occupant in a moderate to severe frontal collision.
Main Menu Table of Contents Your Car's Safety Features Seats & Seat-Backs Your car's seats are designed to keep you in a comfortable, upright position so you can take full advantage of the protection offered by seat belts and the energy absorbing materials in the seats. How you adjust your seats and seatbacks can also affect your safety.
Main Menu Table of Contents Your Car's Safety Features Door Locks Keeping your doors locked reduces the chance of being thrown out of the car during a crash. It also helps prevent occupants from accidentally opening a door and falling out, and outsiders from unexpectedly opening your doors.
Main Menu Table of Contents Protecting Adults Introduction The following pages provide instructions on how to properly protect the driver and other adult occupants. These instructions also apply to children who have outgrown child seats and are large enough to wear lap/shoulder belts. (See page 37 for important additional guidelines on how to properly protect larger children.) 1.Close and Lock the Doors After everyone has entered the car, be sure the doors are closed and locked.
Main Menu Table of Contents Protecting Adults Most shorter drivers can get far To reduce the chance of injury, wear enough away from the steering your seat belt properly, sit upright wheel and still reach the pedals. with your back against the seat, and However, if you are concerned about move the seat as far back as possible sitting too close, we recommend that from the steering wheel while still 03/07/10 16:11:09 31S5A930 0021 you investigate whether some type maintaining full control of the car.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Protecting Adults A front passenger should also adjust the seat-back to an upright position, but as far from the dashboard as possible. A passenger who sits too close to the dashboard could be injured if the airbag inflates. Reclining a seat-back so that the shoulder part of the belt no longer rests against the occupant's chest reduces the protective capability of the belt.
Main Menu 03/07/10 Table of Contents 16:11:09 31S5A930 0021 Protecting Adults Improperly positioning head restraints reduces their effectiveness and you can be seriously injured in a crash. Make sure head restraints are in place and positioned properly before driving. Properly adjusted head restraints will help protect occupants from whiplash and other crash injuries. See page 79 for how to adjust the head restraints. 5.
Main Menu Table of Contents Protecting Adults If necessary, pull up on the belt again to remove any slack from the shoulder part, then check that the belt rests across the center of your 03/07/10 16:11:09 31S5A930 0021 chest and over your shoulder. This spreads the forces of a crash over the strongest bones in your upper body. Improperly positioning the seat belts can cause serious injury or death in a crash. Make sure all seat belts are properly positioned before driving.
Main Menu Table of Contents Protecting Adults Using the Lap Belt Insert the latch plate into the buckle marked CENTER. If the belt is too short, hold the latch plate at a right angle and pull on the plate to extend the belt. Then insert the latch plate into the buckle, and tug on the belt to make sure the belt is securely latched. If a Seat Belt Doesn't Work Properly If a seat belt does not seem to work as it should, it may not protect the occupant in a crash.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 Protecting Adults 6.Adjust the Steering Wheel Adjust the steering wheel, if needed, so that the wheel points toward your chest, not toward your face. Pointing the steering wheel toward your chest provides optimal protection from the airbag. See page 65 for how to adjust the steering wheel. Driver and Passenger Safety 7.
Main Menu Table of Contents Protecting Adults Advice for Pregnant Women Pregnant women should also sit upright and as far back as possible from the steering wheel or dashboard. This will reduce the risk of injuries to both the mother and her unborn child that can be caused by a crash or an inflating airbag. Each time you have a check-up, ask your doctor if it's okay for you to drive.
Main Menu Table of Contents Protecting Adults Do not place hard or sharp objects between yourself and an airbag. Carrying hard or sharp objects on your lap, or driving with a pipe or other sharp object in your mouth, can result in injuries if your airbags inflate. Do not attach or place objects on the airbag covers. Any object attached to or placed on the covers marked "SRS AIRBAG," in the center of the steering wheel and on top of the dashboard, could interfere with the proper operation of the airbags.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Protecting Children Children who are unrestrained or improperly restrained can be seriously injured or killed in a crash. Any child too small for a seat belt should be properly restrained in a child seat. A larger child should be properly restrained with a seat belt. Children depend on adults to protect them. However, despite their best intentions, many parents and other adults may not know how to properly protect young passengers.
Main Menu Table of Contents Protecting Children Children Should Sit in the Back Seat According to accident statistics, children of all ages and sizes are safer when they are restrained in the back seat, not the front seat. The National Highway Traffic Safety Administration and Transport Canada recommend that all children ages 12 and under be properly restrained in the back seat. In the back seat, children are less likely to be injured by striking hard interior parts during a collision or hard braking.
Main Menu Table of Contents Protecting Children U.S. Models To remind you of the passenger's airbag hazards, and that children must be properly restrained in the back seat, your car has warning labels on the dashboard and on the driver's and front passenger's visors. Please read and follow the instructions on these labels. Canadian Models To remind you of the airbag hazards, your car has warning labels on the driver's and front passenger's visors.
Main Menu Table of Contents Protecting Children If You Must Drive with Several Children Your car has three seating positions in the back seat where children can be properly restrained. If you ever have to carry more than three children in your car: Place the largest child in the front seat, provided the child is large enough to wear a seat belt properly (see page 37 ). Move the vehicle seat as far to the rear as possible (see page 12). Have the child sit upright and well back in the seat (see page 18).
Main Menu Table of Contents Protecting Children Do not leave children alone in your vehicle. Leaving children without adult supervision is illegal in most states and Canadian provinces, and can be very hazardous. For example, infants and small children left in a vehicle on a hot day can die from heatstroke. And children left alone with the key in the ignition can accidentally set the vehicle in motion, possibly injuring themselves or others.
Main Menu Table of Contents Protecting Children 3. The child seat should fit the vehicle seating position (or positions) where it will be used. Due to variations in the design of child seats, vehicle seats, and seat belts, all child seats will not fit all vehicle seating positions. Small Children: A child who is too large for a rear-facing child seat, and who can sit up without support, should be restrained in a forwardfacing child seat.
Main Menu Table of Contents Protecting Children Placing a Child Seat This page briefly summarizes Honda's recommendations on where to place rear-facing and forwardfacing child seats in your car. Airbags Pose Serious Risks to Children The passenger's airbag inflates with enough force to kill or seriously injure an infant in a rear-facing child seat. A small child in a forward-facing child seat is also at risk.
Main Menu Table of Contents Protecting Children Installing a Child Seat To provide security during normal driving maneuvers as well as during a collision, we recommend that parents secure a child seat as firmly as possible. 1. Secure the child seat to the car with a seat belt. All child seats must be secured to the car with the lap belt or the lap part of a lap/ shoulder belt. A child whose seat is not properly secured to the car can be endangered in a crash.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Protecting Children Protecting Infants Rear-Facing Child Seat Placement Placing a rear-facing child seat in the front seat can result in serious injury or death if the airbags inflate. Always place a rear-facing child seat in the back seat, not the front. Child Seat Type Only a rear-facing child seat provides proper support for a baby's head, neck, and back.
Main Menu Table of Contents Protecting Children Installing a Rear-Facing Child Seat with a Lap/Shoulder Belt The lap/shoulder belts in the outer back seats have a locking mechanism that must be activated to secure a child seat. The following pages provide instructions on how to secure a rearfacing child seat with this type of seat belt. See page 32 for how to secure a rearfacing child seat in the center back seat with the lap belt.
Main Menu Table of Contents Protecting Children To deactivate the locking mechanism and remove a child seat, unlatch the buckle, unroute the seat belt, and let the belt fully retract. 4. After confirming that the belt is locked, grab the shoulder part of the belt near the buckle and pull up to remove any slack from the lap part of the belt. Remember, if the lap part of the belt is not tight, the child seat will not be secure.
Main Menu Table of Contents Protecting Children Installing a Rear-Facing Child Seat with the Lap Belt To install a rear-facing child seat in the center back seat with the lap belt, follow instruction number 1 on page 30 for routing and latching the seat belt. Then pull hard on the loose end of the belt to remove any slack (it may help to put weight on the child seat while pulling on the belt). Finally, follow instruction number 5 on page 31 to verify that the child seat is secure.
Main Menu Table of Contents Protecting Children Additional Precautions for Infants Never hold an infant on your lap. Protecting Small Children If you are not wearing a seat belt in a crash, you could be thrown forward into the dashboard and crush the infant. Child Seat Placement In this car, the best place to install a forward-facing child seat is in one of the seating positions in the back seat. If you are wearing a seat belt, the infant can be torn from your arms.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Protecting Children Improperly placing a forwardfacing child seat in the front seat can result in serious injury or death if the airbags inflate. If you must place a forwardfacing child seat in front, move the vehicle seat as far back as possible and properly restrain the child.
Main Menu Table of Contents Protecting Children 2. To activate the lockable retractor, slowly pull the shoulder part of the belt all the way out until it stops, then let the belt feed back into the retractor (you might hear a clicking noise as the belt retracts). 3. After the belt has retracted, tug on it. If the belt is locked, you will not be able to pull it out. If you can pull the belt out, it is not locked and you will need to repeat these steps. 4.
Main Menu Table of Contents Protecting Children To deactivate the locking mechanism in order to remove a child seat, unlatch the buckle, unroute the seat belt, and let the belt fully retract. Installing a Child Seat with the Lap Belt Never hold a small child on your lap. If you are not wearing a seat belt in a crash, you could be thrown forward into the dashboard and crush the child.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Protecting Children Protecting Larger Children When a child reaches the recommended weight or height limit for a forward-facing child seat, the child should sit in one of the outer back seats and wear a lap/shoulder belt. The lap/shoulder belt provides better protection than the lap belt.
Main Menu Table of Contents Protecting Children However, if the belt touches or crosses the child's neck, the child needs to use a booster seat. Do not let a child wear a seat belt across the neck. This could result in serious neck injuries during a crash. Do not let a child put the shoulder part of a seat belt behind the back or under the arm. This could cause very serious injuries during a crash. It also increases the chance that the child will slide under the belt in a crash and be injured.
Main Menu Table of Contents Protecting Children A child may continue using a booster seat until the tops of the ears are even with the top of the seat-back. A child of this height should be tall enough to use the lap/shoulder belt without a booster. When Can a Larger Child Sit in Front The National Highway Traffic Safety Administration and Transport Canada recommend that all children ages 12 and under be properly restrained in a back seat.
Main Menu Table of Contents Protecting Children Maturity To safely ride in front, a child must be able to follow the rules, including sitting properly and wearing the seat belt properly throughout a ride. If you decide that a child can safely ride up front, be sure to: Check that the child's seat belt is properly positioned and secured. Using Child Seats with Tethers Supervise the child. Even mature children sometimes need to be reminded to fasten the seat belts or sit properly.
Main Menu Table of Contents Protecting Children Attach the tether strap hook to the tether anchorage point and tighten the strap according to the child seat maker's instructions.
Main Menu Table of Contents Additional Information About Your Seat Belts Seat Belt System Components Your seat belt system includes lap/ shoulder belts in the front seats and the outer back seats, and a lap belt in the center back seat. The seat belt system also includes a light on the instrument panel to remind you and your passengers to fasten your belts. If the driver's seat belt is not fastened before the ignition is turned ON (II), the light will come on and a beeper will also sound.
Main Menu Table of Contents Additional Information About Your Seat Belts If the shoulder part of the belt is pulled all the way out, the locking mechanism will activate. The belt will retract, but it will not allow the passenger to move freely. Lap Belt The lap belt has one manuallyadjusted belt that fits across the hips. To deactivate the locking mechanism, unlatch the buckle and let the seat belt fully retract. To refasten the belt, pull it out only as far as needed.
03/07/10 Main Menu 16:11:09 31S5A930 0021 Table of Contents Additional Information About Your Seat Belts Seat Belt Maintenance For safety, you should check the condition of your seat belts regularly. 03/07/26 19:00:40 31SDP610 0003 For information on how to clean your If a seat belt is worn during a crash, seat belts, see page 234. you should have your dealer inspect Main Menu the belt, and replace it if necessary.
Main Menu Table of Contents Additional Information About Your SRS SRS Components Your Supplemental Restraint System (SRS) includes: Two front airbags. The driver's airbag is stored in the center of the steering wheel; the front passenger's airbag is stored in the dashboard. Both are marked "SRS AIRBAG." Sensors that can detect a moderate to severe frontal collision.
Main Menu Table of Contents Additional Information About Your SRS After a crash, you may see what looks like smoke. This is actually powder from the airbag's surface. Although the powder is not harmful, people with respiratory problems may experience some temporary discomfort. If this occurs, get out of the car as soon as it is safe to do so. Since both airbags use the same sensors, both airbags normally inflate at the same time. However, it is possible for only one airbag to inflate.
Main Menu Table of Contents Additional Information About Your SRS SRS Service How the SRS Indicator Light If the light comes on or flashes on Works Your Supplemental Restraint System and off while you drive. virtually maintenance-free, and purpose of the SRS03/07/10 16:11:09 31S5A930 is0021 SRS The there are no parts you can safely light is to alert you to a If you see any of these indications, service.
Main Menu Table of Contents Additional Information About Your SRS Additional Safety Precautions Do not attempt to deactivate your airbags. Together, airbags and seat belts provide the best protection in a moderate to severe frontal collision. Do not tamper with SRS components or wiring for any reason. Tampering could cause the airbags to deploy, possibly causing very serious injury. See page 150 for further information and precautions relating to your SRS.
Main Menu Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 A Few Words About Safety Carbon Monoxide Hazard Your safety, and the safety of others, You will find th is very important. And operating this including: vehicle safely is an important 03/07/10 16:11:09 31S5A930 0021 03/07/10 16:11:09 31S5A930 0021 With the trunk lid open, air flow canSafety Labe Your car's exhaust contains carbon responsibility. pull exhaust gas into your car's monoxide gas.
Main Menu Table of Contents Safety Labels These labels are in the locations shown. They warn you of potential hazards that could cause serious injury. Read these labels carefully. DASHBOARD U.S. models only SUN VISOR U.S. models If a label comes off or becomes hard to read, contact your Honda dealer for a replacement.
Main Menu Instruments and Controls This section gives information about the controls and displays that contribute to the daily operation of your Honda. All the essential controls are within easy reach. Control Locations............................ 52 Indicator Lights................................ 53 Gauges............................................. . 57 Speedometer................................ 57 Tachometer................................. . 57 Odometer..................................... .
Main Menu Table of Contents Control Locations MIRROR CONTROLS (P.84 ) HEATING/COOLING CONTROLS (P.90 ) AUDIO SYSTEM (P.98, 107, 121 ) DIGITAL CLOCK (P.101, 112, 126 ) POWER DOOR LOCK SWITCH (P.72 ) POWER WINDOW SWITCHES (P.81 ) FUEL FILL DOOR RELEASE (P.143 ) TRUNK RELEASE HANDLE (P.76 ) Instruments and Controls HOOD RELEASE HANDLE (P.
Main Menu Table of Contents Indicator Lights The instrument panel has many indicators to give you important information about your car. * The U.S. instrument panel is shown. Differences for Canadian models are noted in the text. EX and U.S.
Main Menu Table of Contents Indicator Lights U.S. DX and DX Value Package, and Canadian LX and SE HIGH BEAM INDICATOR CHARGING SYSTEM INDICATOR PARKING BRAKE AND BRAKE SYSTEM INDICATOR* TRUNK-OPEN INDICATOR LOW OIL PRESSURE INDICATOR LOW FUEL INDICATOR Seat Belt Reminder Light This indicator lights when you turn the ignition switch ON (II). It is a reminder to you and your passengers to protect yourselves by fastening the seat belts. A beeper also sounds if you have not fastened your seat belt.
Main Menu Table of Contents Indicator Lights Supplemental Restraint System Indicator This indicator lights when you turn the ignition switch ON (II). If it comes on at any other time, it indicates a problem in the supplemental restraint system. For complete information, see page 47. SRS Charging System Indicator If this light comes on when the engine is running, the battery is not being charged. For complete information, see page 250 .
Main Menu Table of Contents Indicator Lights Malfunction Indicator Lamp See page 251. Turn Signal and Hazard Warning Indicators The left or right turn signal light blinks when you signal a lane change or turn. If the light does not blink or blinks rapidly, it usually means one of the turn signal bulbs is burned out (see page 221). Replace the bulb as soon as possible, since other drivers cannot see that you are signalling. When you turn on the Hazard Warning switch, both turn signal lights blink.
Main Menu Table of Contents Gauges EX and U.S. LX TACHOMETER TRIP METER ODOMETER SPEEDOMETER FUEL GAUGE TEMPERATURE GAUGE MAINTENANCE REQUIRED INDICATOR TRIP METER RESET BUTTON Speedometer Tachometer U.S. Models On LX and EX models in U.S., and EX model in Canada This shows your speed in miles per hour (mph). The smaller inner numbers are the speed in kilometers per hour (km/h). Canadian Models This shows your speed in kilometers per hour (km/h).
Main Menu Table of Contents Gauges U.S. DX and DX Value Package, and Canadian LX and SE TEMPERATURE GAUGE TRIP METER SPEEDOMETER ODOMETER MAINTENANCE REQUIRED INDICATOR Fuel Gauge This shows how much fuel you have. It is most accurate when the car is on level ground. It may show slightly more or less than the actual amount when you are driving on curvy or hilly roads.
Main Menu Table of Contents Gauges Maintenance Required Indicator SLOT INDICATOR When the distance driven since the last scheduled maintenance nears 7,500 miles (12,000 km), the indicator will turn yellow. If you exceed 7,500 miles (12,000 km), the indicator will turn red. Your dealer will reset the indicator when he performs the scheduled maintenance. If someone else performs the maintenance, reset the indicator by inserting your key in the slot beside the indicator. U.S.
Main Menu Table of Contents Controls Near the Steering Wheel The two levers on the steering column contain controls for driving features you use most often. The left lever controls the turn signals, headlights, and high beams. The right lever controls the windshield washers and wipers. CRUISE CONTROL INSTRUMENT PANEL BRIGHTNESS HAZARD WARNING LIGHTS MOONROOF The hazard warning lights switch is on the dashboard to the left of the center air vents.
Main Menu Table of Contents Controls Near the Steering Wheel Headlights The rotating switch on the left lever controls the lights. Turning this switch to the " " position turns on the parking lights, taillights, instrument panel lights, side-marker lights, and rear license plate lights. Turning the switch to the " " position turns on the headlights. If you leave the lights on with the ignition switch in ACCESSORY (I) or LOCK (0), you will hear a reminder beeper when you open the driver's door.
Main Menu Table of Contents Controls Near the Steering Wheel Instrument Panel Brightness Turn Signals TURN SIGNAL LEVER The dial on the dashboard to the left of the instrument panel controls the brightness of the instrument panel lights. Turn the dial to adjust the brightness. Instruments and Controls Signal a turn or lane change with this lever. Push down on the lever to signal a left turn, and up to signal a right turn.
Main Menu Table of Contents Controls Near the Steering Wheel Windshield Washers Windshield Wipers The right lever controls the windshield wipers and washers. The rotary switch at the end of the lever has three positions: INT: intermittent : low speed : high speed In intermittent, the wipers operate every few seconds. In low speed and high speed, the wipers run continuously. To operate the wipers in mist mode, push the control lever down. The wipers run at high speed until you release the lever.
Main Menu Table of Contents Controls Near the Steering Wheel Hazard Warning Rear Window Defogger Make sure the rear window is clear and you have good visibility before starting to drive. The defogger and antenna wires on the inside of the rear window can be accidentally damaged. When cleaning the glass, always wipe side to side. Push the red button to the left of the center vents to turn on the hazard warning lights (four-way flashers).
Main Menu Table of Contents 03/07/26 Steering Wheel Adjustment 19:00:40 Main Menu See page 18 for important safety information about how to properly A Few Words 03/07/10 16:11:09 31S5A930 0021 position the steering wheel. Controls Near the Steering Wheel 31SDP610 About Safety 0003 3. Push the lever up to lock the steering wheel in that position. 4. Make sure you have securely locked the steering wheel in place by to move it up and down.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Steering Wheel Controls Cruise Control On LX and EX models in the U.S., and EX model in Canada Cruise control allows you to maintain a set speed above 25 mph (40 km/h) without keeping your foot on the accelerator pedal. It should be used for cruising on straight, open highways. It is not recommended for conditions such as city driving, winding roads, slippery roads, heavy rain, or bad weather.
Main Menu Table of Contents Steering Wheel Controls RESUME/ accel SET/decel 3. Press and release the SET/decel button on the steering wheel. The CRUISE CONTROL light on the instrument panel comes on to show the system is now activated. The cruise control may not hold the set speed when you are going up and down hills. If your speed increases going down a hill, use the brakes to slow down to the desired speed. This will cancel the cruise control. To resume the set speed, press the RESUME/accel button.
Main Menu Table of Contents Steering Wheel Controls You can decrease the set cruising speed in any of these ways: Press and hold the SET/decel button. The car will decelerate. Release the button when you reach the desired speed. To slow down in very small amounts, tap the SET/decel button repeatedly. Each time you do this, your car will slow down about 1 mph (1.6 km/h). Tap the brake or clutch pedal lightly with your foot. The CRUISE CONTROL light on the instrument panel will go out.
Main Menu Table of Contents Steering Wheel Controls, Keys and Locks When you tap the brake or clutch pedal, or press the SET and RESUME buttons at the same time, the CRUISE CONTROL light on the instrument panel will go out and the car will begin to slow down. You can use the accelerator pedal in the normal way. The system remembers the previously-set cruising speed. To return to that speed, accelerate to above 25 mph (40 km/h) and press the RESUME/accel button until the CRUISE CONTROL light comes on.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 002 Keys and Locks Ignition Switch The ignition switch is on the right side of the steering column. It has four positions: LOCK (0) ACCESSORY (I) ON (II) START (III) Instruments and Controls LOCK (0) — You can insert or remove the key only in this position. To switch from ACCESSORY to LOCK, you must push the key in slightly as you turn it. If your car has an automatic transmission, the shift lever must also be in Park.
Main Menu Table of Contents Keys and Locks ACCESSORY (I) — In this position, you can operate the audio system and the accessory power socket. Door Locks ON (II) — This is the normal key position when driving. All features and accessories on the car are usable. Several of the lights on the instrument panel come on as a test when you turn the ignition switch from ACCESSORY to ON. START (III) — Use this position only to start the engine. The switch returns to ON (II) when you let go of the key.
Main Menu Table of Contents Keys and Locks Power Door Locks MASTER DOOR LOCK SWITCH On DX Value Package, LX and EX models in the U.S., and SE and EX models in Canada The master door lock switch allows control of all door locks from the driver's door. Push the switch down to lock all doors, and up to unlock them. Instruments and Controls All doors lock when you push down the lock tab on the driver's door, or lock the driver's door from the outside with the key.
Main Menu Table of Contents Keys and Locks Remote Transmitter LED LOCK BUTTON UNLOCK BUTTON PANIC BUTTON Standard on the DX Value Package and EX models in the U.S., and SE model in Canada Optional on the LX model in the U.S. You can lock and unlock your car with the remote transmitter. When you push the LOCK button, all doors lock. The parking lights, side marker lights, and taillights flash once. When you push the UNLOCK button once, only the driver's door unlocks.
Main Menu Table of Contents Keys and Locks Replacing the Battery ROUND COVER Open CUSHION RING BATTERY Close When the remote transmitter's battery begins to get weak, it may take several pushes on the button to lock or unlock the doors, and the LED will get dim. Replace the battery as soon as possible. Battery type: CR2025 Instruments and Controls To replace the battery, remove the round cover on the back of the transmitter by turning it counterclockwise with a coin.
Main Menu Table of Contents Keys and Locks Transmitter Care Avoid severe shock to the transmitter, such as dropping or throwing it. Also, protect it from extreme hot or cold temperatures. Clean the transmitter case with a soft cloth. Do not use strong cleaners or solvents that could harm the case. Immersing the transmitter in any liquid will harm the transmitter and cause it to not function properly.
Main Menu Table of Contents Keys and Locks Trunk TRUNK RELEASE HANDLE You can open the trunk in two ways: Pull the trunk release handle to the left of the driver's seat. Use the master key to open the trunk lock. The valet key does not work in this lock. Instruments and Controls MASTER KEY To close the trunk, press down on the trunk lid. See page 151 for cargo loading and weight limit information.
Main Menu Table of Contents Seat Adjustments Front Seat Adjustments See pages 12 — 13 for important safety information and warnings about how to properly position seals and seat-backs. Make all seat adjustments before you start driving. To adjust the seat forward and backward, pull up on the lever under the seat cushion's front edge. Move the seat to the desired position and release the lever. Try to move the seat to make sure it is locked in position.
Main Menu Table of Contents Seat Adjustments Driver's Seat Height Adjustment On LX and EX models in the U.S., and EX model in Canada The height of your driver's seat is adjustable. Turn the front dial on the outside of the seat cushion to raise the front of the seat bottom and turn the rear dial to raise the rear. Instruments and Controls Make all adjustments before you start driving.
Main Menu Table of Contents Seat Adjustments Head Restraints To remove a head restraint for cleaning or repair, pull it up as far as it will go. Push the release button and pull the restraint out of the seatback. See page 14 for important safety information and a warning about how to properly position the head restraints. The front head restraints help protect you and your passenger from whiplash and other injuries.
Main Menu Table of Contents Folding Rear Seat The back of the rear seat folds down to give you direct access to the trunk. Each side folds down separately. With only half the seat folded, you can still carry a passenger in the back seat. The seat-back can be released from inside the car or inside the trunk. MASTER KEY RELEASE To fold down either side of the seatback from inside the car, insert the master key in the lock on the rear shelf.
Main Menu Table of Contents Folding Rear Seat, Power Windows Do not put any heavy items on the seat-back when it is folded. Make sure all items in the trunk, or items extending through the opening into the back seat, are secured. Loose items can fly forward and cause injury if you have to brake hard. See Carrying Cargo on page 151. Never drive with the seat-back folded down and the trunk lid open. See Carbon Monoxide Hazard on page 49. switch and holding it.
Main Menu Table of Contents Power Windows The master control panel also contains these extra features: AUTO — To open the driver's window fully, push the window switch firmly down and release it. The window automatically goes all the way down. To stop the window from going all the way clown, pull back on the window switch briefly. To open the driver's window only partially, push the window switch down lightly and hold it. The window will stop as soon as you release the switch.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Moonroof To close the moonroof, press and hold the switch. Moonroof, Mirrors Mirrors Closing the moonroof on someone's hands or fingers can cause serious injury. Make sure passengers are clear of the moonroof before closing it. TAB On U.S. EX model Use the switches on the dashboard under the left vent to operate the moonroof. The ignition must be ON (II). To lift the rear of the moonroof for ventilation, push the button.
Main Menu Table of Contents Mirrors Adjusting the Power Mirrors SELECTOR SWITCH On LX and EX models in the U.S., and EX model in Canada Adjust the outside mirrors with the adjustment switch on the left side of the dashboard: 1. Turn the ignition switch ON (II). 2. Move the selector switch to L (driver's side) or R (passenger's side). Instruments and Controls ADJUSTMENT SWITCH 3. Push the appropriate edge of the adjustment switch to move the mirror right, left, up or down. 4.
Main Menu Table of Contents Parking Brake NOTICE Driving the car with the parking brake applied can damage the rear brakes and axles. PARKING BRAKE LEVER To apply the parking brake, pull the lever up fully. To release it, pull up slightly, push the button, and lower the lever. The parking brake light on the instrument panel should go out when the parking brake is fully released (see page 55).
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Glove Box, Beverage Holder Beverage Holder Glove Box An open glove box can cause serious injury to your passenger in a crash, even if the passenger is wearing the seat belt. Always keep the glove box closed while driving. GLOVE BOX Open the glove box by pulling the handle. Close it with a firm push. Be careful when you are using the beverage holder. A spilled liquid that is very hot can scald you or your passengers.
Main Menu Table of Contents Accessory Power Socket, Ashtrays Accessory Power Socket This socket is intended to supply power for 12 volt DC accessories that are rated 120 watts or less (10 amps). It will not power an automotive type cigarette lighter element. Ashtrays (Optional) Front and rear ashtrays are available as options. The front ashtray fits in the beverage holder. The rear ashtray fits in the rear of the center armrest. Open the rear ashtray by swinging the upper edge down.
Main Menu Table of Contents Interior Lights Ceiling Light Spotlights DOOR ACTIVATED ON DOOR ACTIVATED OFF OFF OFF ON ON U.S. EX The ceiling light has a three-position switch. In the OFF position, the light does not come on. In the center position, the ceiling light comes on when you open any door. In the ON position, the ceiling light stays on continuously. Instruments and Controls except U.S.
Main Menu Comfort and Convenience Features The heating and air conditioning* systems in your Honda provide a comfortable driving environment in all weather conditions. The standard audio system has many features. This section describes those features and how to use them. (If you selected an optional audio system, refer to the operating instructions that came with it.) * Air conditioning is standard on the DX Value Package, LX and EX models in the U.S., and SE model in Canada.
Main Menu Table of Contents Heating and Cooling Proper use of the Heating and Cooling system can make the interior dry and comfortable, and keep the windows clear for best visibility. If your car does not have air conditioning, it can be installed at any time. Your dealer can install a Genuine Honda air conditioning system that meets Honda's high quality standards and is designed to exactly fit your car. Please contact your dealer for more information.
Main Menu Table of Contents Heating and Cooling Mode Control Dial Use the MODE control dial to select the vents the air flows from. Some air will flow from the dashboard vents in all modes. Air flows from the center and corner vents in the dashboard. Air flow is divided between the vents in the dashboard and the floor vents. vents. Air flows from the floor Air flow is divided between the floor vents and the defroster vents at the base of the windshield.
Main Menu Table of Contents Heating and Cooling Vent Controls CENTER VENT SIDE VENT Open Close You can adjust the direction of the air coming from the dashboard vents by moving the tab in the center of each vent up-and-down and side-toside. Comfort and Convenience Features The vents in the corners of the dashboard can be opened and closed with the dials next to them.
Main Menu Table of Contents Heating and Cooling It is best to leave the system in Fresh Air mode under almost all conditions. Keeping the system in Recirculation mode, particularly with the A/C off, can cause the windows to fog up. Switch to Recirculation mode when you are driving through smoky or dusty conditions, then switch back to Fresh Air mode when the condition clears. The outside air intakes for the heating and cooling system are at the base of the windshield.
Main Menu Table of Contents Heating and Cooling RECIRCULATION BUTTON To Cool with A/C 1. Turn on the A /C by pressing the button. The light in the button should come on when a fan speed is selected. 2. Make sure the temperature control dial is all the way to the left. 3. Select 4. If the outside air is humid, select Recirculation mode. If the outside air is dry, select Fresh Air mode. 5. Set the fan to the desired speed.
Main Menu Table of Contents Heating and Cooling To Heat To warm the interior: 1. Start the engine. 2. Select and Fresh Air mode. 3. Set the fan to the desired speed. 4. Adjust the warmth of the air with the temperature control dial. To Heat and Dehumidify with Air Conditioning Air conditioning, as it cools, removes moisture from the air. When used in combination with the heater, it makes the interior warm and dry. 1. Switch the fan on. 2. Turn on the air conditioning. 3. Select and Fresh Air mode. 4.
Main Menu Table of Contents Heating and Cooling To remove exterior frost or ice from the windshield and side windows after the car has been sitting out in cold weather: 1. Start the engine. 2. Select When you select , the system automatically switches to Fresh Air mode and turns on the A/C. 3. Switch the fan and temperature controls to maximum. MODE CONTROL DIAL TEMPERATURE CONTROL DIAL To rapidly remove exterior frost or ice from the windshield (on very cold days), first select the Recirculation mode.
Main Menu Table of Contents Heating and Cooling These settings direct all the air flow to the defroster vents at the base of the windshield and the side window defroster vents. The air flow will get warmer and clear the windows faster as the engine warms up. You can close the side vents with the dial beside each vent. This will send more warm air to the windshield defroster vents. For safety, make sure you have a clear view through all the windows before driving away.
Main Menu Table of Contents Audio System A M / FM Stereo Audio System For DX and LX models in the U.S., and LX and SE models in Canada Your Honda's audio system provides clear reception on both AM and FM bands, while the preset buttons allow you to easily select your favorite stations. Operating the Radio The ignition switch must be in ACCESSORY (I) or ON (II) to operate the audio system. Turn the system on by pressing the PWR/ VOL knob or the A M / FM button. Adjust the volume by turning the knob.
Main Menu Table of Contents Audio System To store a frequency: 1. Select the desired band, AM or FM. FM1 and FM2 let you store two frequencies with each Preset button. PWR/VOL KNOB STEREO INDICATOR AM/FM BUTTON 2. Use the TUNE or SEEK function to tune the radio to a desired station. 3. Pick the Preset button you want for that station. Press the button and hold it until you hear a beep. 4. Repeat steps 1 to 3 to store a total of six stations on AM and twelve on FM.
Main Menu Table of Contents Audio System Adjusting the Sound Bass, Treble, Balance, and Fader are each adjustable. You select which of these you want to adjust by pressing the MODE button. The mode changes from BAS to TRE to FAD to BAL, and then back to VOL each time you press the button. Each mode is shown in the display as it changes. Balance/Fader — These two modes adjust the strength of the sound coming from each speaker.
Main Menu Table of Contents Audio System Digital Clock The audio system also displays the time. The ignition switch must be in ACCESSORY (I) or ON (II). TIME DISPLAYED To set the time, press the CLOCK button. The hour numbers will begin blinking. Press the Preset 5 button to get the numbers to count down, or the Preset 6 button to get the hours to count up. Press the CLOCK button again, and the minutes numbers will begin blinking.
Main Menu Table of Contents Audio System Operating the Optional Cassette Player The cassette system features Dolby B* noise reduction, automatic sensing of chromium-dioxide (CrO2) tape, and autoreverse for continuous play. * Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. "DOLBY" and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.
Main Menu Table of Contents Audio System TMS — The Tape Music Search function allows you to find the beginning of a song or passage. To activate TMS, press FF or REW until you hear a beep. You will see TMS displayed. When the system reaches the beginning of the next song or passage (FF), or the beginning of the song just played (REW), it goes back to PLAY mode. REPEAT — The Repeat function continuously replays the current song or passage.
Main Menu Table of Contents Audio System Operating the Optional CD Player/Changer A Compact Disc changer is available through your dealer. It holds up to six discs, providing several hours of continuous entertainment. You operate the CD changer with the same controls used for the radio. Your dealer also has an accessory indash single CD player available that is operated by the radio controls. To operate this unit, use the instructions (except for those relating to multiple discs) in this section.
Main Menu Table of Contents Audio System Press the EJECT button to remove the disc from the player. If you eject the disc, but do not remove it from the slot, the system will automatically reload the disc after 15 seconds and put the CD player in pause mode. To begin playing the disc, press the CD button. To select a different disc, press the appropriate preset button (1 — 6).
Main Menu Table of Contents Audio System CD Changer Error Indications If you see an error indication in the display while operating the CD changer, find the cause in the chart to the right. If you cannot clear the error indication, take the car to your Honda dealer.
Main Menu Table of Contents Audio System AM/FM/Cassette Stereo Audio System On Canadian EX model only Your Honda's audio system provides clear reception on both AM and FM bands, while the preset buttons allow you to easily select your favorite stations. The cassette system features Dolby B* noise reduction, automatic sensing of chromium-dioxide (CrO2) tape, and autoreverse for continuous play. * Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation.
Main Menu Table of Contents Audio System Operating the Radio The ignition switch must be in ACCESSORY (I) or ON (II) to operate the audio system. Turn the system on by pushing the PWR/ VOL knob. Adjust the volume by turning the PWR/VOL knob. The band and frequency that the radio was last tuned to is displayed. To change bands, press the AM/FM button. On the FM band, ST will be displayed if the station is broadcasting in stereo. Stereo reproduction on AM is not available.
Main Menu Table of Contents Audio System SCAN — The SCAN function samples all the stations with strong signals on the selected band. To activate it, press the SCAN button, then release it. When the system is in the SCAN mode, SCN shows in the display. The system will scan up the band for a station with a strong signal. When it finds one, it will stop and play that station for approximately five seconds.
Main Menu Table of Contents Audio System Preset — You can store the frequencies of your favorite radio stations in the six preset buttons. Each button will store one frequency on the AM band, and two frequencies on the FM band. AM/FM BUTTON To store a frequency: 1. Select the desired band, AM or FM. FM1 and FM2 let you store two frequencies with each Preset button. 2. Use the TUNE or SEEK function to tune the radio to a desired station. 3. Pick the Preset button you want for that station.
Main Menu Table of Contents Audio System Adjusting the Sound Balance/Fader — These two controls adjust the strength of the sound coming from each speaker. The Balance control adjusts the sideto-side strength, while the Fader control adjusts the front-to-back strength. BASS/FADER CONTROL TREBLE/BALANCE CONTROL To adjust the fader, push on the BASS/FADER control knob to get it to pop out. Pull it out slightly farther, and adjust the front-to-back sound to your liking.
Main Menu Table of Contents Audio System Radio Frequencies and Reception For information, See page 127. CLOCK BUTTON Audio System Lighting You can use the instrument panel brightness control dial to adjust the illumination of the audio system (see page 62). The audio system illuminates when the parking lights are on, even if the radio is turned off. Digital Clock The display of your audio system usually shows the time when the ignition switch is in ACCESSORY (I) or ON (II).
Main Menu Table of Contents Audio System You can use the RESET (Preset 6) button to quickly set the time to the nearest hour. If the displayed time is before the half hour, pressing RESET sets the clock back to the previous hour. If the displayed time is after the half hour, pressing RESET sets the clock forward to the beginning of the next hour.
Main Menu Table of Contents Audio System Dolby B noise reduction turns on when you insert a cassette. If the tape was not recorded with Dolby B noise reduction, turn it off by pressing the button. When the system reaches the end of the tape, it will automatically reverse direction and play the other side. If you want to remove the cassette from the drive, press the EJECT button.
Main Menu Table of Contents Audio System REPEAT — The Repeat function continuously replays the current song or passage. Press the RPT button to activate it; you will see RPT displayed as a reminder. When the system reaches the end of the song or passage currently playing, it will automatically go into rewind. When it senses the beginning of the same song or passage, the system returns to PLAY mode. It will continue to repeat this same program until you deactivate REPEAT by pressing the button again.
Audio System The SKIP and REPEAT functions use silent periods on the tape to find the end of a song or passage. These features may not work to your satisfaction if there is almost no gap between selections, a high noise level between selections, or a silent period in the middle of selection. CASSETTE SLOT EJECT BUTTON RPT BUTTON REW BUTTON TAPE DIRECTION INDICATOR FF BUTTON Caring for Cassettes Damaged cassettes can jam inside the drive or cause other problems.
Main Menu Table of Contents Audio System Operating the Optional CD Player/Changer A Compact Disc changer is available from your dealer. It holds up to six discs, providing several hours of continuous entertainment. You operate the CD changer with the same controls used for the radio and cassette player. TAPE/CD BUTTON RANDOM INDICATOR REPEAT INDICATOR AM/FM BUTTON Your dealer also has an accessory indash single CD player available that is operated by the radio controls.
Main Menu Table of Contents Audio System To operate the CD changer or player, the ignition must be in ACCESSORY (I) or ON (II) and the audio system must be on. Press the CD button until "CD" appears in the display. The system will start to play the first track of the first disc in the magazine. Play only standard round discs. When that disc ends, the next disc in the magazine is loaded and played. After the last disc finishes, the system returns to disc 1.
Main Menu Table of Contents Audio System If the system is in Repeat mode, you must turn it off by pressing RPT before you can select Random Play. Then press the button again until you see RDM displayed. RANDOM INDICATOR AM/FM BUTTON TAPE/CD BUTTON REPEAT INDICATOR To take the system out of CD mode, press the A M / FM button or insert a cassette in the player. If a tape is already in the cassette player, press the TAPE button. When you return to CD mode, play will continue at the same disc and track.
Main Menu Table of Contents Audio System CD Changer Error Indications If you see an error indication in the display while operating the CD changer, find the cause in the chart to the right. If you cannot clear the error indication, take the car to your Honda dealer.
Main Menu Table of Contents Audio System AM/FM/CD Audio System On U.S. DX Value Package and EX models Your Honda's audio system provides clear reception on both AM and FM bands, while the preset buttons allow you to easily select your favorite stations. The anti-theft feature will disable the system if it is disconnected from the car's battery. To get the system working again, you must enter a code number (see page 139).
Main Menu Table of Contents Audio System Operating the Radio The ignition switch must be in ACCESSORY CD or ON (II) to operate the audio system. Turn the system on by pushing the PWR/ VOL knob. Adjust the volume by turning the same knob. PWR/VOL KNOB SCAN INDICATOR AM/FM BUTTON TUNE BAR STEREO INDICATOR SEEK BAR The band and frequency that the radio was last tuned to is displayed. To change bands, press the A M / FM button.
Main Menu Table of Contents Audio System TUNE — Use the TUNE bar to tune the radio to a desired frequency. Press the side of the bar to tune to a higher frequency, and the side to tune to a lower frequency. The frequency numbers will start to change rapidly. Release the bar when the display reaches the desired frequency. To change the frequency in small increments, press and release the TUNE bar quickly. SEEK — The SEEK function searches the band for a station with a strong signal.
Main Menu Table of Contents Audio System AUTO SELECT — If you are traveling far from home and can no longer receive the stations you preset, you can use the Auto Select feature to find stations in the local area. To activate Auto Select, press the A. SEL button. A. SEL will flash in the display, and the system will go into scan mode for several seconds.
Main Menu Table of Contents Audio System Adjusting the Sound Balance/Fader — These two controls adjust the strength of the sound coming from each speaker. The Balance control adjusts the sideto-side strength, while the Fader control adjusts the front-to-back strength. To adjust the fader, push on the BASS/FADER control knob to get it to pop out. Pull it out slightly farther, and adjust the front-to-back sound to your liking.
Main Menu Table of Contents Audio System Audio System Lighting You can use the instrument panel brightness control dial to adjust the illumination of the audio system (see page 62). The audio system illuminates when the parking lights are on, even if the radio is turned off. Digital Clock The display of your audio system usually shows the time when the ignition switch is in ACCESSORY (I) or ON (II).
Main Menu Table of Contents Audio System Radio Frequencies Your Honda's radio can receive the complete AM and FM bands. Those bands cover these frequencies: AM band: 530 to 1,710 kilohertz FM band: 87.7 to 107.9 megahertz Radio stations on the AM band are assigned frequencies at least ten kilohertz apart (530, 540, 550). Stations on the FM band are assigned frequencies at least 0.2 megahertz apart (87.9, 88.1, 88.3). Stations must use these exact frequencies.
Main Menu Table of Contents Audio System Electrical interference from passing vehicles and stationary sources can cause temporary reception problems. As required by the FCC: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Radio signals, especially on the FM band, are deflected by large objects such as buildings and hills.
Main Menu Table of Contents Audio System Operating the CD Player You operate the CD player with the same controls used for the radio. With the ignition switch in ACCESSORY (I) or ON (II), insert the disc into the CD slot. Push the disc in halfway, the drive will pull it in the rest of the way and begin to play. The number of the track that is playing is shown in the display. CD SLOT AM/FM BUTTON TUNE BAR EJECT BUTTON PWR/VOL KNOB You can also play 3-inch (8-cm) discs without using an adapter ring.
Main Menu Table of Contents Audio System You can switch to the radio while a CD is playing by pressing the A M / FM button. Press the CD button to return to playing the CD. The CD will begin playing where it left off. If you turn the system off while a CD is playing, either with the PWR/VOL knob or by turning off the ignition, the disc will stay in the drive. When you turn the system back on, the CD will begin playing where it left off. Press the eject button to remove the disc from the drive.
Main Menu Table of Contents Audio System Operating the CD Changer (Optional) A Compact Disc changer is available for your vehicle. It holds up to six discs, providing several hours of continuous entertainment. You operate this CD changer with the same controls used for the in-dash CD player. Load the desired CDs in the magazine and load the magazine in the changer according to the instructions that came with the unit. Play only standard round discs.
Main Menu Table of Contents Audio System Protecting Compact Discs Handle a CD by its edges; never touch either surface. Contamination from fingerprints, liquids, felt-tip pens, and labels can cause the CD to not play properly, or possibly jam in the drive. When a CD is not being played, store it in its case to protect it from dust and other contamination. To prevent warpage, keep CDs out of direct sunlight and extreme heat. To clean a disc, use a clean soft cloth.
Main Menu Table of Contents Audio System CD Player Error Indications If you see an error indication in the display while operating the CD player, find the cause in the chart to the right. If you cannot clear the error indication, take the car to your Honda dealer.
Main Menu Table of Contents Audio System CD Changer Error Indications If you see an error indication in the display while operating the CD changer, find the cause in the chart to the right. If you cannot clear the error indication, take the car to your Honda dealer.
Main Menu Table of Contents Audio System Operating the Cassette Player (Optional) The cassette system features Dolby B* noise reduction, automatic sensing of chromium-dioxide (CrO2) tape, and autoreverse for continuous play. CD BUTTON TUNE BAR SEEK/SKIP BAR PWR/VOL KNOB AM/FM BUTTON TAPE DIRECTION INDICATOR Make sure the tape opening on the cassette is facing to the right, then insert the cassette most of the way into the slot. The system will pull it in the rest of the way, and begin to play.
Main Menu Table of Contents Audio System The tape direction indicator will light to show you which side of the cassette is playing. The indicates the side you inserted facing upward is now playing. If you want to play the other side, press the PROG button. Dolby B noise reduction turns on when you insert a cassette. If the tape was not recorded with Dolby B noise reduction, turn it off by pressing the NR button. Dolby remains off until you turn it on by pressing the button again.
Main Menu Table of Contents Audio System SKIP — The skip function allows you to find the beginning of a song or passage. To activate SKIP, press the SEEK/SKIP bar. Press the side to advance to the beginning of the next song or passage, or the side to return to the beginning of the current song or passage. FF or REW will flash in the display as the tape moves. When the system reaches the beginning of the next song or passage (FF), or the beginning of the current one (REW), it goes back to PLAY mode.
Main Menu Table of Contents Audio System Caring for the Cassette Player The cassette player picks up dirt and oxides from the tape. This contamination builds up over time and causes the sound quality to degrade. To prevent this, you should clean the player after every 30 hours of use. Your dealer has a cleaning kit available. If you do not clean the cassette player regularly, it may eventually become impossible to remove the contamination with a normal cleaning kit. Use 100-minute or shorter cassettes.
Main Menu Table of Contents Audio System Theft Protection On U.S. DX Valve Package and EX models Your car's audio system will disable itself if it is disconnected from electrical power for any reason. To make it work again, the user must enter a specific five-digit code in the Preset buttons. Because there are hundreds of number combinations possible from five digits, making the system work without knowing the exact code is nearly impossible.
Main Menu 140
Main Menu Before Driving Before you begin driving your Honda, you should know what gasoline to use, and how to check the levels of important fluids. You also need to know how to properly store luggage or packages. The information in this section will help you. If you plan to add any accessories to your car, please read the information in this section first. Break-in Period.............................. 142 Gasoline......................................... . 142 Service Station Procedures ..........
Main Menu Table of Contents Break-in Period, Gasoline Break-in Period Help assure your car's future reliability and performance by paying extra attention to how you drive during the first 600 miles (1,000 km). During this period: Avoid full-throttle starts and rapid acceleration. Avoid hard braking. New brakes need to be broken-in by moderate use for the first 200 miles (300 km). You should follow these same recommendations with an overhauled or exchanged engine, or when the brakes are relined.
Main Menu Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 A Few Words About Safety Service Station Procedures Your safety, and the safety of others, You will find th is very important. And operating this including: vehicle safely is an important 03/07/10 16:11:09 31S5A930 0021 03/07/10 16:11:09 31S5A930 Filling the Fuel Tank 3.0021 Remove the fuel fill cap slowly. Safety Labe responsibility. You may hear a hissing sound as Safety Mess pressure inside the tank escapes.
Main Menu Table of Contents Service Station Procedures 5. Screw the fuel fill cap back on, tighten it until it clicks at least three times. If you do not properly tighten the cap, the Malfunction Indicator Lamp may come on (see page 251). 6. Push the fuel fill door closed until it latches. Opening the Hood LATCH HOOD RELEASE HANDLE 1. Shift to Park or Neutral and set the parking brake. Pull the hood release handle located under the lower left corner of the dashboard. The hood will pop up slightly.
Main Menu Table of Contents Service Station Procedures If you can open the hood without lifting the hood latch handle, or the hood latch handle moves stiffly or does not spring back as before, the mechanism should be cleaned and lubricated (see page 202). SUPPORT ROD After closing the hood, make sure it is securely latched. CLIP 3. Pull the support rod out of its clip and insert the end into the hole on the left side of the hood.
Main Menu Table of Contents Service Station Procedures Oil Check DIPSTICK Check the engine oil level every time you fill the car with fuel. Wait a few minutes after turning the engine off before you check the oil. 1. Remove the dipstick (orange handle). Before Driving 2. Wipe the dipstick with a clean cloth or paper towel. 3. Insert it all the way back in its tube.
Main Menu Table of Contents Service Station Procedures Engine Coolant Check RESERVE TANK UPPER MARK LOWER MARK 4. Remove the dipstick again and check the level. It should be between the upper and lower marks. If it is near or below the lower mark, see Adding Oil on page 187. Refer to Owner Maintenance Checks on page 185 for information on checking other items in your Honda. MAX MIN Look at the coolant level in the radiator reserve tank. Make sure it is between the MAX and M IN lines.
Main Menu Table of Contents Fuel Economy The condition of your car and your driving habits are the two most important things that affect the fuel mileage you get. Vehicle Condition Always maintain your car according to the maintenance schedule. This will keep it in top operating condition. An important part of that maintenance is the Owner Maintenance Checks (see page 185). For example, an underinflated tire causes more "rolling resistance," which uses fuel.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Accessories and Modifications Modifying your car, or installing some non-Honda accessories, can make your car unsafe. Before you make any modifications or add any accessories, be sure to read the following information. Accessories Your dealer has Genuine Honda accessories that allow you to personalize your car. These accessories have been designed and approved for your car, and are covered by warranty.
Main Menu Table of Contents Accessories and Modifications Modifications Do not remove any original equipment or modify your car in any way that would alter its design or operation. This could make your car unsafe and illegal to drive. In addition, any modifications that decrease ground clearance increase the chance of undercarriage parts striking a curb, speed bump, or other raised object, which could cause your airbags to deploy.
Main Menu Table of Contents Carrying Cargo CONSOLE COMPARTMENT* FRONT DOOR POCKET Your car has several convenient storage areas so you can stow cargo safely. The glove box, and the pockets in the front doors and seat-back, are designed for small, lightweight items. The trunk is intended for larger, heavier items. In addition, the back seat can be folded down to allow you to carry more cargo or longer items.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Carrying Cargo Load Limit The maximum load for your car is 850 lbs (395 kg). This figure includes the total weight of all occupants, cargo, and accessories. To figure out how much cargo you can carry: Add up the weight of all occupants. Subtract the total from 850 lbs (395 kg). The final number is the total weight of cargo you can carry.
Main Menu Table of Contents Carrying Cargo Carrying Cargo in the Trunk or on a Roof Rack Distribute cargo evenly on the floor of the trunk, placing the heaviest items on the bottom and as far forward as possible. If you can carry any items on a roof rack, be sure the total weight of the rack and the items does not exceed the maximum allowable weight. Please contact your Honda dealer for further information.
Main Menu 154
Main Menu Driving This section gives you tips on starting the engine under various conditions, and how to operate the 5-speed manual and automatic transmissions. It also includes important information on parking your car, and the braking system. Preparing to Drive......................... 156 Starting the Engine........................ 157 Starting in Cold Weather at High Altitude ..................... 157 5-speed Manual Transmission..... 158 Recommended Shift Points...... 159 Engine Speed Limiter........
Main Menu Table of Contents Preparing to Drive You should do the following checks and adjustments every day before you drive your car. 1. Make sure all windows, mirrors, and outside lights are clean and unobstructed. Remove frost, snow, or ice. 2. Check that the hood and trunk are fully closed. 3. Visually check the tires. If a tire looks low, use a gauge to check its pressure. Driving 4. Check that any items you may be carrying with you inside are stored properly or fastened down securely. 5.
Main Menu Table of Contents Starting the Engine 1. Apply the parking brake. 2. In cold weather, turn off all electrical accessories to reduce the drain on the battery. 3. Manual Transmission: Push the clutch pedal down all the way. START (III) does not function unless the clutch pedal is depressed. Automatic Transmission: Make sure the shift lever is in Park. Press on the brake pedal. 4. Without touching the accelerator pedal, turn the ignition key to the START (III) position.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 002 5-speed Manual Transmission Come to a full stop before you shift into Reverse. You can damage the transmission by trying to shift into Reverse with the car moving. Push down the clutch pedal, and pause for a few seconds before shifting into Reverse, or shift into one of the forward gears for a moment. This stops the gears so they won't "grind." The manual transmission is synchronized in all forward gears for smooth operation.
Main Menu Table of Contents 5-speed Manual Transmission Recommended Shift Points Drive in the highest gear that lets the engine run and accelerate smoothly. This will give you the best fuel economy and effective emissions control. The following shift points are recommended: Engine Speed Limiter On EX and U.S. LX models If you exceed the maximum speed for the gear you are in, the engine speed will enter into the tachometer's red zone. If this occurs, you may feel the engine cut in and out.
Main Menu Table of Contents Automatic Transmission Your Honda's transmission has four forward speeds, and is electronically controlled for smoother shifting. It also has a "lock-up" torque converter for better fuel economy. You may feel what seems like another shift when the converter locks. Shift Lever Position Indicator EX and U.S. LX This indicator on the instrument panel shows which position the shift lever is in. Driving Except EX and U.S.
Main Menu Table of Contents Automatic Transmission Shift Lever Positions RELEASE BUTTON SHIFT LEVER The shift lever has six positions. It must be in Park or Neutral to start the engine. When you are stopped in D4, D3, 2, N or R, press firmly on the brake pedal, and keep your foot off the accelerator pedal. Park (P) — This position mechanically locks the transmission. Use Park whenever you are turning off or starting the engine.
Main Menu Table of Contents Automatic Transmission If you have done all of the above and still cannot move the lever out of Park, see Shift Lock Release on page 164. You must also press the release button to shift into Park. To avoid transmission damage, come to a complete stop before shifting into Park. The shift lever must be in Park before you can remove the key from the ignition switch. Driving Reverse (R) — To shift to Reverse from Park, see the explanation under Park.
Main Menu Table of Contents Automatic Transmission Drive (D3) —This position is similar to D4, except only the first three gears are selected. Use D3 to provide engine braking when going down a steep hill. D3 can also keep the transmission from cycling between third and fourth gears in stop-and-go driving. For faster acceleration when in D3 or D4, you can get the transmission to automatically downshift by pushing the accelerator pedal to the floor.
Main Menu Table of Contents Automatic Transmission Shift Lock Release This allows you to move the shift lever out of Park if the normal method of pushing on the brake pedal and pressing the release button does not work. RELEASE BUTTON 1. Set the Parking brake. 2. Remove the key from the ignition switch. 3. Put a cloth on the edge of the Shift Lock Release slot cover next to the shift lever.
Main Menu Table of Contents Parking Always use the parking brake when you park your car. The indicator on the instrument panel shows that the parking brake is not fully released; it does not indicate that the parking brake is firmly set. Make sure the parking brake is set firmly or your car may roll if it is parked on an incline. If the car is facing uphill, turn the front wheels away from the curb. If you have a manual transmission, put it in first gear.
Main Menu Table of Contents The Braking System All Civics are equipped with front disc brakes. The brakes on the rear wheels are drum. A power assist helps reduce the effort needed on the brake pedal. Put your foot on the brake pedal only when you intend to brake. Resting your foot on the pedal keeps the brakes applied lightly, causing them to build up heat. Heat build-up can reduce how well your brakes work. It also keeps your brake lights on all the time, confusing drivers behind you.
Main Menu Table of Contents The Braking System Brake System Design The hydraulic system that operates the brakes has two separate circuits. Each circuit works diagonally across the vehicle (the left-front brake is connected with the right-rear brake, etc.). If one circuit should develop a problem, you will still have braking at two wheels. Front Anti-lock Brakes The U.S. EX model has an Anti-lock Brake System (ABS) as standard equipment. It is optional on Canadian EX model.
Main Menu Table of Contents The Braking System Activation varies with the amount of traction your tires have. On dry pavement, you will need to press on the brake pedal very hard before you activate the ABS. However, you may feel the ABS activate immediately if you are trying to stop on snow or ice. Important Safety Reminders ABS does not reduce the time or distance it takes to stop the car, it only helps with steering control during braking.
Main Menu Table of Contents The Braking System ABS Indicator ABS INDICATOR* *U.S. indicator shown The ABS is self-checking. If anything goes wrong, the ABS indicator on the instrument panel comes on (see page 55), This means the anti-lock function of the braking system has shut down. The brakes still work like a conventional system without antilock, providing normal stopping ability.
Main Menu Table of Contents Driving in Bad Weather Rain, fog, and snow conditions require a different driving technique because of reduced traction and visibility. Keep your car wellmaintained and exercise greater caution when you need to drive in bad weather. The cruise control should not be used in these conditions. Driving Driving Technique — Always drive slower than you would in dry weather. It takes your car longer to react, even in conditions that may seem just barely damp.
Main Menu Table of Contents Driving in Bad Weather, Towing a Trailer Towing a Trailer Your vehicle is not designed to tow a trailer. Attempting to do so can void your warranties. Traction — Check your tires frequently for wear and proper pressure. Both are important in preventing "hydroplaning" (loss of traction on a wet surface). In the winter, mount snow tires on all four wheels for the best handling. Watch road conditions carefully, they can change from moment to moment.
Main Menu 172
Main Menu Maintenance This section explains why it is important to keep your car well maintained and to follow basic maintenance safety precautions. This section also includes Maintenance Schedules for normal driving and severe driving conditions, a Maintenance Record, and instructions for simple maintenance tasks you may want to take care of yourself. If you have the skills and tools to perform more complex maintenance tasks on your Honda, you may want to purchase the Service Manual.
Main Menu Table of Contents Maintenance Safety Regularly maintaining your car is the best way to protect your investment. Proper maintenance is essential to 03/07/10 16:11:09 31S5A930 your safety and the safety of your passengers. It will also reward you with more economical, trouble-free driving and help reduce air pollution. Improperly maintaining this car or failing to correct a problem before driving can cause a crash in which you can be seriously hurt or killed.
Main Menu Table of Contents Maintenance Safety Important Safety Precautions Before you begin any maintenance, make sure your car is parked on level ground and that the parking brake is set. Also, be sure the engine is off. This will help to eliminate several potential hazards: Carbon monoxide poisoning from engine exhaust. Be sure there is adequate ventilation whenever you operate the engine. Burns from hot parts. Let the engine and exhaust system cool before touching any parts. Injury from moving parts.
Main Menu Table of Contents Maintenance Schedule The Maintenance Schedule specifies how often you should have your car serviced and what things need attention. It is essential that you have your car serviced as scheduled to retain its high level of safety, dependability, and emissions control performance. The services and time or distance intervals shown in the maintenance schedule assume you will use your car as normal transportation for passengers and their possessions.
Main Menu Table of Contents Maintenance Schedule Your authorized Honda dealer knows your car best and can provide competent, efficient service. However, service at a dealer is not mandatory to keep your warranties in effect. Maintenance may be done by any qualified service facility or person who is skilled in this type of automotive service. Keep all the receipts as proof of completion, and have the person who does the work fill out the Maintenance Record. Check your warranty booklet for more information.
Main Menu Table of Contents U.S. Owners Follow the Normal Conditions Maintenance Schedule if the severe driving conditions specified in the Severe Conditions Maintenance Schedule do not apply. NOTE: If you only OCCASIONALLY drive under a "severe" condition, you should follow the Normal Conditions Maintenance Schedule. Canadian Owners Follow the Maintenance Schedule for Severe Conditions. # : See information on maintenance and emissions warranty, last column, page 177.
Main Menu Table of Contents Service at the indicated distance or time, whichever comes first. Do the items in A, B, C as required for each distance/time interval. Follow this schedule if the severe driving conditions described in the Severe Conditions Schedule on the next page do not apply. Canadian owners: Follow the schedule for Severe Conditions. paqe 214 # : See information on maintenance and emissions warranty, last column, page 177. NOTE: Check engine oil and coolant at each fuel stop.
Main Menu Table of Contents U.S. Owners Follow the Severe Conditions Maintenance Schedule if you drive your vehicle MAINLY under one or more of the following conditions: Driving less than 5 miles (8 km) per trip or, in freezing temperatures, driving less than 10 miles (16 km) per trip. Driving in extremely hot [over 90° F (32° C)] conditions. Extensive idling or long periods of stop-and-go driving. Driving with a roof-top carrier, or driving in mountainous conditions.
Main Menu Table of Contents Use this schedule if your vehicle is MAINLY driven in any of the following Severe Conditions, or normally driven in Canada; otherwise use the Normal Schedule. Service at the indicated distance or time, whichever comes first. Do the items in A, B, C, D as required for each distance/time. Severe Conditions: Driving less than 5 miles (8 km) per trip or, in freezing temperatures, driving less than 10 miles (16 km) per trip. Driving in extremely hot (over 90°F/32°C) conditions.
Main Menu Table of Contents # : See information on maintenance and emissions warranty, last column, page 177. * : See Timing Belt on page 210 to determine need for replacement. NOTE: Check engine oil and coolant at each fuel stop.
Main Menu Table of Contents Required Maintenance Record (for Normal and Severe Schedules) You or the servicing dealer can record all completed maintenance here, whether you follow the schedule for normal conditions (page 178) or severe conditions (page 180). Keep the receipts for all work done on your vehicle.
Main Menu Table of Contents Required Maintenance Record (for Normal and Severe Schedules) Maintenance
Main Menu Table of Contents Owner Maintenance Checks You should check the following items at the specified intervals. If you are unsure of how to perform any check, turn to the page given. Engine oil level — Check every time you fill the fuel tank. See page 146. Engine coolant level — Check the radiator reserve tank every time you fill the fuel tank. See page 147 . Windshield washer fluid — Check the level in the reservoir monthly.
Main Menu Table of Contents Fluid Locations BRAKE FLUID (Gray cap) CLUTCH FLUID (5-speed Manual Transmission only) (Gray cap) ENGINE OIL FILL CAP WASHER FLUID (Blue cap) ENGINE COOLANT RESERVOIR POWER STEERING FLUID (Red cap) AUTOMATIC TRANSMISSION FLUID DIPSTICK (Yellow loop) RADIATOR CAP Maintenance ENGINE OIL DIPSTICK (Orange loop)
Main Menu Table of Contents Engine Oil Adding Oil ENGINE OIL FILL CAP Recommended Oil Oil is a major contributor to your engine's performance and longevity. Always use a premium-grade detergent oil. It is highly recommended that you use Genuine Honda Motor Oil in your vehicle for as long as you own it. The API Service label also tells you the service classification of the oil. Always use an oil that is labeled "API Service SJ." This service rating may include other classifications, such as CD.
Main Menu Table of Contents Engine Oil The oil container may also display the API Certification seal. Make sure it says "For Gasoline Engines." API CERTIFICATION SEAL The SAE numbers tell you the oil's viscosity or weight. Select the oil for your car according to this chart. Ambient Temperature An oil with a viscosity of 5W-30 is preferred for improved fuel economy and year-round protection in your Honda. You may use a 10W-30 oil if the temperature in your area never goes below 20°F(— 7°C).
Main Menu Table of Contents Engine Oil Changing the Oil and Filter Always change the oil and filter according to the time and distance (miles/kilometers) recommendations in the maintenance schedule. The oil and filter collect contaminants that can damage your engine if they are not removed regularly. Changing the oil and filter requires special tools and access from underneath the car. The car should be raised on a service station-type hydraulic lift for this service.
Main Menu Table of Contents Engine Oil 5. Put a new washer on the drain bolt, then reinstall the drain bolt. Tighten it to: (U.S.: DX, DX Value Package, LX, Canada: LX, SE, EX) 33 lbf·ft (44 N·m, 4.5 kgf·m) (U.S.: EX) 29 Ibf·ft (39 N·m , 4.0 kgf·m) 6. Refill the engine with the recommended oil. Engine oil change capacity (including filter): (U.S.: DX, DX Value Package, LX, Canada: LX, SE, EX) 3.8 US qt (3.6 , 3.2 Imp qt) (U.S.: EX) 3.5 US qt (3.3 Maintenance , 2.9 Imp qt) 7.
Main Menu Table of Contents 03/07/26 19: Cooling System Main Me A Few Wor 03/07/10 16:11:09 31S5A930 002 Adding Engine Coolant RESERVE TANK If the coolant level in the reserve tank is at or below the MIN line, add coolant to bring it up to the MAX line. Inspect the cooling system for leaks. This coolant should always be a mixture of 50 percent antifreeze and 50 percent water. Never add straight antifreeze or plain water.
Main Menu Table of Contents Cooling System RADIATOR CAP 2. Turn the radiator cap counterclockwise, without pressing down on it, until it stops. This relieves any pressure remaining in the cooling system. 3. Remove the radiator cap by pushing down and turning counterclockwise. Maintenance RESERVE TANK 4. The coolant level should be up to the base of the filler neck. Add coolant if it is low. 5. Put the radiator cap back on. Tighten it fully. 6. Pour coolant into the reserve tank.
Main Menu Table of Contents Cooling System Replacing Engine Coolant The cooling system should be completely drained and refilled with new coolant according to the time and distance recommendations in the maintenance schedule. Only use Genuine Honda Antifreeze/Coolant. Draining the coolant requires access to the underside of the car. Unless you have the tools and knowledge, you should have this maintenance done by a skilled mechanic. DRAIN PLUG 1. Turn the ignition ON (II).
Main Menu Table of Contents Cooling System RESERVE TANK RESERVE TANK CAP 5. When the coolant stops draining, tighten the drain plug at the bottom of the radiator. FILLER NECK 6. Mix the recommended antifreeze with an equal amount of purified or distilled water in a clean container. The cooling system capacity is: HOLDER 4. Remove the reserve tank from its holder by pulling it straight up. Drain the coolant, then put the tank back in its holder. With 5-speed manual transmission: 0.82 US gal (3.
Main Menu Table of Contents Cooling System 9. Fill the reserve tank to the MAX mark. Install the reserve tank cap. 13.Start the engine and hold it at 1,500 rpm until the radiator fan comes on. Turn off the engine. Check the coolant level in the radiator and add coolant if needed. 10.Install the radiator cap, and tighten it to the first stop. 14.Install the radiator cap, and tighten it fully. 8. Check the level in the radiator, add coolant if needed. RESERVE TANK 15.
Main Menu Table of Contents Windshield Washers Check the level in the windshield washer reservoir at least monthly during normal usage. In bad weather, when you use the washers often, check the level every time you stop for fuel. The windshield washer reservoir is located behind the driver's side headlight. Check the reservoir's fluid level by removing the cap and looking at the level gauge attached to the cap.
Main Menu Table of Contents Transmission Fluid Automatic Transmission DIPSTICK UPPER MARK LOWER MARK Check the fluid level with the engine at normal operating temperature. 1. Park the car on level ground. Shut off the engine. 2. Remove the dipstick (yellow loop) from the transmission and wipe it with a clean cloth. 5. If the level is below the lower mark, add fluid into the filler hole to bring it to the upper mark. Always use Honda Premium Formula Automatic Transmission Fluid (ATF).
Main Menu Table of Contents Transmission Fluid, Brake and Clutch Fluid 5-speed Manual Transmission FILLER BOLT Correct level Check the fluid level with the transmission at normal operating temperature and the car sitting on level ground. Remove the transmission filler bolt and carefully feel inside the bolt hole with your finger. The fluid level should be up to the edge of the bolt hole. If it is not, add Genuine Honda Manual Transmission Fluid (MTF) until it starts to run out of the hole.
Main Menu Table of Contents Brake and Clutch Fluid Always use Genuine Honda DOT 3 brake fluid. If it is not available, you should use only DOT 3 or DOT 4 fluid, from a sealed container, as a temporary replacement. However, the use of any non-Honda brake fluid can cause corrosion and decrease the life of the system. Have the brake system flushed and refilled with Honda DOT 3 brake fluid as soon as possible.
Main Menu Table of Contents Power Steering You should check the fluid level in the power steering reservoir monthly. Check the level when the engine is cold. Look at the side of the reservoir. The fluid should be between the UPPER LEVEL and LOWER LEVEL. If it is below the LOWER LEVEL, add power steering fluid to the UPPER LEVEL. UPPER LEVEL NOTICE Turning the steering wheel to full left or right lock and holding it there can damage the power steering pump.
Main Menu Table of Contents Air Cleaner Element The air cleaner element should be replaced according to the time and distance recommendations in the maintenance schedule. Replacement CLIPS AIR CLEANER ELEMENT On DX, DX Value Package and LX models in the U.S., and all models in Canada The air cleaner element is inside the air cleaner housing in the engine compartment. To replace it: 1. Unsnap the four clips and remove the air cleaner housing cover. 2. Remove the old air cleaner element. 3.
Main Menu Table of Contents Air Cleaner Element. Hood Latch Replacement Hood Latch AIR CLEANER ELEMENT LATCH ASSEMBLY CLIPS On EX model in the U.S. The air cleaner element is inside the air cleaner housing on the passenger's side of the engine compartment. To replace it: 1. Unsnap the two clips and remove the air cleaner housing cover. 2. Remove the old air cleaner element. Maintenance PIVOTS 3. Carefully clean the inside of the air cleaner housing with a damp rag. 4.
Main Menu Table of Contents Spark Plugs The spark plugs in your car should be replaced according to the time and distance recommendations in the maintenance schedule. Replacement SPARK PLUG CAP 1. Clean up any dirt and oil around the spark plug caps. 2. Remove the spark plug cap by pulling it straight out. 4. Put the new spark plug into the socket; then screw it into the hole. Screw it in by hand so you do not crossthread it. 3. Remove the spark plug with a five-eighths inch (16 mm) spark plug socket.
Main Menu Table of Contents Spark Plugs NOTICE Tighten the spark plugs carefully. A spark plug that is too loose can overheat and damage the engine. Overtightening can cause damage to the threads in the cylinder head. 6. Install the spark plug cap. 7. Repeat this procedure for the other three spark plugs. 5. Torque the spark plug. (If you do not have a torque wrench, tighten the spark plug two-thirds of a turn after it contacts the cylinder head.) Tightening torque: 13 lbf·ft (18 N·m,1.
Main Menu Table of Contents Battery Check the condition of your car's battery monthly. You should check the color of the test indicator window, and for corrosion on the terminals. TEST INDICATOR WINDOW Check the battery terminals for corrosion (a white or yellowish powder). To remove it, cover the terminals with a solution of baking soda and water. It will bubble up and turn brown. When this stops, wash it off with plain water. Dry off the battery with a cloth or paper towel.
Main Menu Table of Contents 03/07/26 Battery 19:00:40 31SDP610 0003 Main Menu 03/07/10 16:11:09 A Few 0021 Words About Safety 31S5A930 If you need to connect the battery to NOTICE a charger, disconnect both cables to prevent damage to the car's Charging the battery the cables Your safety, and the safety ofwith others, You will find th electrical system. connectedAnd can seriously your is very important. operatingdamage this including: car's electronic controls.
Main Menu Table of Contents Wiper Blades Check the condition of the wiper blades at least every six months. Look for signs of cracking in the rubber, or areas that are getting hard. Replace the blades if you find these signs, or they leave streaks and unwiped areas when used. WIPER ARMS LOCK TAB To replace the blade: 1. Raise the wiper arm off the windshield. 2. Disconnect the blade assembly from the wiper arm by pushing in the lock tab.
Main Menu Table of Contents Wiper Blades BLADE BLADE 5. Slide the new wiper blade into the holder until the tabs lock. 6. Slide the wiper blade assembly onto the wiper arm. Make sure it locks in place. 7. Lower the wiper arm down against the windshield. REINFORCEMENT 3. Remove the blade from its holder by grasping the tabbed end of the blade. Pull firmly until the tabs come out of the holder. Maintenance 4. Examine the new wiper blades.
Main Menu Table of Contents Air Conditioning System Optional for U.S. DX, and Canadian LX, EX models Your car's air conditioning is a sealed system. Any major maintenance, such as recharging, should be done by a qualified mechanic. You can do a couple of things to make sure the air conditioning works efficiently. Periodically check the engine's radiator and air conditioning condenser for leaves, insects, and dirt stuck to the front surface. These block the air flow and reduce cooling efficiency.
Main Menu Table of Contents Drive Belts, Timing Belt Drive Belts POWER STEERING BELT ALTERNATOR BELT The belts should have the following "play" or deflection. Alternator belt: 0.31 — 0.41 in (8.0 — 10.5 mm) Power steering belt: 0.41 — 0.55 in (10.5—14.0 mm) On cars with Air Conditioning System Compressor belt: 0.30 — 0.37 in (7.5 — 9.5 mm) COMPRESSOR BELT Check the condition of the two or three drive belts. Examine the edges of each belt for cracks or fraying.
Main Menu Table of Contents Tires To safely operate your car, your tires Inflation must be the proper type and size, in Keeping the tires properly inflated good condition with adequate tread, provides the best combination of and correctly inflated. The following handling, tread life and riding pages give more detailed information comfort.
Main Menu Table of Contents Tires You should get your own tire pressure gauge and use it whenever you check your tire pressures. This will make it easier for you to tell if a pressure loss is due to a tire problem and not due to a variation between gauges. Recommended Tire Pressures for Normal Driving The following chart shows the recommended cold tire pressures for most normal driving conditions and speeds. Maintenance The compact spare tire pressure is: 60 psi (420 kPa , 4.
Main Menu Table of Contents Tires Inspection Every time you check inflation, you should also examine the tires for damage, foreign objects, and wear. INDICATOR LOCATION MARKS You should look for: Bumps or bulges in the tread or side of the tire. Replace the tire if you find either of these conditions. Cuts, splits, or cracks in the side of the tire. Replace the tire if you can see fabric or cord. Excessive tread wear. TREAD WEAR INDICATOR Your car's tires have wear indicators molded into the tread.
Main Menu Table of Contents Tires Make sure the installer balances the wheels when you have new tires installed. This increases riding comfort and tire life. Your car's original tires were dynamic or "spin" balanced at the factory. For best results, have the installer perform a dynamic balance.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Tires Replacing Tires and Wheels The tires that came with your car were selected to match the performance capabilities of the car while providing the best combination of handling, ride comfort, and long life. You should replace them with radial tires of the same size, load range, speed rating, and maximum cold tire pressure rating (as shown on the tire's sidewall).
Main Menu Table of Contents Tires Wheels and Tires Wheels: 14 x 5 J Tires: P185/65R14 85S See page 266 for information about DOT Tire Quality Grading. Maintenance Winter Driving Tires that are marked " M + S" or "All Season" on the sidewall have an all-weather tread design. They should be suitable for most winter driving conditions. Tires without these markings are designed for optimum traction in dry conditions. They may not provide adequate performance in winter driving.
Main Menu Table of Contents Tires Tire Chains Mount snow chains on your vehicle when warranted by driving conditions or required by local laws. Make sure the chains are the correct size for your tires. Install them only on the front tires. If metal chains are used, they must be SAE class "S." Cable type traction devices can also be used. NOTICE Chains of the wrong size or that are improperly installed can damage your car's brake lines, suspension, body, and wheels.
Main Menu Table of Contents Lights Check the operation of your car's exterior lights at least once a month. A burned out bulb can create an unsafe condition by reducing your car's visibility and the ability to signal your intentions to other drivers.
Main Menu Table of Contents Lights Check the following: HIGH-MOUNT BRAKE LIGHT STOP/TAILLIGHTS/ REAR SIDE MARKER LIGHTS LICENSE PLATE LIGHTS TURN SIGNAL LIGHTS TAILLIGHT Headlights (low and high beam) Parking lights Taillights Brake lights High-mount brake light Turn signals Back-up lights Hazard light function License plate light Side marker lights Daytime running lights (Canadian models) If you find any bulbs are burned out, replace them as soon as possible.
Main Menu Table of Contents Lights Replacing a Headlight Bulb Your car has halogen headlight bulbs, one on each side. When replacing a bulb, handle it by its steel base and protect the glass from contact with your skin or hard objects. If you touch the glass, clean it with denatured alcohol and a clean cloth. HOLDER NOTICE Halogen headlight bulbs get very hot when lit. Oil, perspiration, or a scratch on the glass can cause the bulb to overheat and shatter. Maintenance WEATHER SEAL CONNECTOR 1.
Main Menu Table of Contents Lights 3. Remove the rubber weather seal by pulling on the tab. 4. Unclip the end of the hold-down wire from its slot. Pivot it out of the way and remove the bulb. 5. Insert the new bulb into the hole, making sure the tabs are in their slots. Pivot the hold-down wire back in place and clip the end into the slot. 7. Push the electrical connector onto the tabs of the new bulb. Make sure it locks in place. Turn on the headlights to test the new bulb. 8.
Main Menu Table of Contents Lights 6. Install the new bulb in the socket. Turn it clockwise to lock it in place. HOLDING CLIP 7. Insert the socket back into the headlight assembly. Turn it clockwise to lock it in place. 8. Test the lights to make sure the new bulb is working. 9. Put the inner fender cover in place. Install the holding clip. Lock it in 2. Use a flat-tipped screwdriver to remove the holding clip from the inner fender. 4.
Main Menu Table of Contents Lights Replacing Rear Bulbs (in Fenders) 4. Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms. 5. Reinstall the socket into the light assembly by turning it clockwise until it locks. 6. Test the lights to make sure the new bulb is working. 1. Open the trunk. Undo the fastener on the side of the trunk lining by pushing on the center of the fastener's head until it pops in. Pull the lining back. 2.
Main Menu Table of Contents Lights 9. Put the fastener in the hole on the side of the trunk lining and push on the center until it locks (the center is flush with the head). 8. Reset the fastener by pushing on the pointed end until it pops back almost flush with the fingers on the housing. Replacing Rear Bulbs (in Trunk Lid) 1. Open the trunk. 2. Determine which of the two bulbs is burned out: taillight or back-up light. 3. Remove the socket by turning it one-quarter turn counterclockwise.
Main Menu Table of Contents Lights 4. Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms. Replacing a High-mount Brake Light Bulb 3. Reinstall the socket. Turn it clockwise until it locks. Make sure the new bulb is working. 5. Insert the socket back into the light assembly. Turn it clockwise to lock it in place. 6. Test the lights to make sure the new bulb is working. 1.
Main Menu Table of Contents Lights Replacing a Rear License Bulb 4. Turn on the parking lights and check that the new bulb is working. 5. Put the lens back on the bulb holder and push it until it latches. Put the light assembly back into the hole. Push it to snap it in place. 1. Remove the license light assembly by carefully prying on the edge of the lens with a flat-tip screwdriver and pulling the assembly out. 2.
Main Menu Table of Contents Lights Replacing Bulbs in the Interior Lights CEILING LIGHT CEILING LIGHT SPOTLIGHT U.S. EX except U.S. EX EX model Although the ceiling light and spotlights come apart the same way, they do not use the same type of bulbs. 1. Remove the lens by carefully prying on the edge of the lens in the middle with a fingernail file or a small flat-tip screwdriver. Do not pry on the edge of the housing around the lens. 2. Remove the bulb by pulling it straight out of its metal tabs.
Main Menu Table of Contents Lights Replacing the Trunk Light Bulb The trunk light is available on LX and EX models in the U.S., and all models in Canada TRUNK LIGHT 1. Remove the lens by carefully prying on the edge of the lens in the middle with a fingernail file or a small flat-tip screwdriver. Do not pry on the edge of the housing around the lens. Maintenance 2. Remove the bulb by pulling it straight out of its metal tabs. 3. Push the new bulb into the metal tabs. Snap the lens back in place.
Main Menu Table of Contents Storing Your Car If you need to park your car for an extended period (more than one month), there are several things you should do to prepare it for storage. Proper preparation helps prevent deterioration and makes it easier to get your car back on the road. If possible, store your car indoors. Fill the fuel tank. Change the engine oil and filter (see page 189). Wash and dry the exterior completely. Clean the interior. Make sure the carpeting, floor mats, etc.
Main Menu 230
Main Menu Appearance Care Regular cleaning and polishing of your Honda helps to keep it "new" looking. This section gives you hints on how to clean your car and preserve its appearance: the paint, brightwork, wheels and interior. Also included are several things you can do to help prevent corrosion. Exterior Care.................................. 232 Washing..................................... . 232 Waxing....................................... . 233 Paint Touch-up...........................
Main Menu Table of Contents Exterior Care Washing Frequent washing helps preserve your car's beauty. Dirt and grit can scratch the paint, while tree sap and bird droppings can permanently ruin the finish. Wash your car in a shady area, not in direct sunlight. If the car is parked in the sun, move it into the shade and let the exterior cool down before you start. Only use the solvents and cleaners recommended in this Owner's Manual.
Main Menu Table of Contents Exterior Care Waxing Always wash and dry the whole car before waxing it. You should wax your car, including the metal trim, whenever water sits on the surface in large patches. It should form into beads or droplets after waxing. You should use a quality liquid or paste wax. Apply it according to the instructions on the container. In general, there are two types of products: Waxes — A wax coats the finish and protects it from damage by exposure to sunlight, air pollution, etc.
Main Menu Table of Contents Interior Care Carpeting Vacuum the carpeting frequently to remove dirt. Ground-in dirt will make the carpet wear out faster. Periodically shampoo the carpet to keep it looking new. Use one of the foam-type carpet cleaners on the market. Follow the instructions that come with the cleaner, applying it with a sponge or soft brush. Keep the carpeting as dry as possible by not adding water to the foam. Fabric Vacuum dirt and dust out of the material frequently.
Main Menu Table of Contents Interior Care, Corrosion Protection Windows Clean the windows, inside and out, with a commercially-available glass cleaner. You can also use a mixture of one part white vinegar to ten parts water. This will remove the haze that builds up on the inside of the windows. Use a soft cloth or paper towels to clean all glass and clear plastic surfaces. NOTICE The rear window defogger and antenna wires are bonded to the inside of the glass.
Main Menu Table of Contents Corrosion Protection, Body Repairs Inspect and clean out the drain holes in the bottom of the doors and body. Check the floor coverings for dampness. Carpeting and floor mats may remain damp for a long time, especially in winter. This dampness can eventually cause the floor panels to corrode. Use a high-pressure spray to clean the underside of your car. This is especially important in areas that use road salt in winter.
Main Menu Taking Care of the Unexpected This section covers the morecommon problems that motorists experience with their vehicles. It gives you information about how to safely evaluate the problem and what to do to correct it. If the problem has stranded you on the side of the road, you may be able to get going again. If not, you will also find instructions on getting your car towed. Compact Spare Tire....................... 238 Changing a Flat Tire..................... 239 If Your Engine Won't Start.....
Main Menu Table of Contents Compact Spare Tire Your car has a compact spare tire that takes up less space. Use this spare tire as a temporary replacement only. Get your regular tire repaired or replaced and put back on your car as soon as you can. Check the inflation pressure of the compact spare tire every time you check the other tires. It should be inflated to: 60 psi (420 kPa , 4.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Changing a Flat Tire If you have a flat tire while driving, stop in a safe place to change it. Stopping in traffic or on the shoulder of a busy road is dangerous. Drive slowly along the shoulder until you get to an exit or an area to stop that is far away from the traffic lanes. SPARE TIRE TRUNK FLOOR The car can easily roll off the jack, seriously injuring anyone underneath.
Main Menu Table of Contents Changing a Flat Tire JACK WHEEL WRENCH 6. Turn the jack's end bracket counterclockwise to loosen it, then remove the jack. Taking Care of the Unexpected 7. Loosen the four wheel nuts 1/2 turn with the wheel wrench. JACKING POINT 8. Locate the jacking point nearest the tire you need to change. It is pointed to by an arrow molded into the underside of the body. Place the jack under the jacking point.
Main Menu Table of Contents Changing a Flat Tire WHEEL NUTS WHEEL WRENCH EXTENSION 9. Use the extension and wheel wrench as shown to raise the car until the flat tire is off the ground. WHEEL COVER 10.Remove the wheel nuts and wheel cover. The wheel cover cannot be removed without first removing the wheel nuts. Do not attempt to forcibly pry the wheel cover off with a screwdriver or other tool. Remove the flat tire.
Main Menu Table of Contents Changing a Flat Tire BRAKE HUB 11.Before mounting the spare tire, wipe any dirt off the mounting surface of the wheel and hub with a clean cloth. Wipe the hub carefully, it may be hot from driving. Taking Care of the Unexpected 12.Put on the spare tire. Put the wheel nuts back on finger-tight, then tighten them in a crisscross pattern with the wheel wrench until the wheel is firmly against the hub. Do not try to tighten them fully. 13.
Main Menu Table of Contents Changing a Flat Tire 03/07/10 16:11:09 31S5A930 0021 WING BOLT SPACER CONE 18.Store the jack in the trunk with the end bracket on the right side. Turn the jack's end bracket to lock it in place. Store the tool kit. Loose items can fly around the interior in a crash and could seriously injure the occupants. 14.Tighten the wheel nuts securely in the same crisscross pattern. Have the wheel nut torque checked at the nearest automotive service facility.
Main Menu Table of Contents If Your Engine Won't Start Diagnosing why your engine won't start falls into two areas, depending on what you hear when you turn the key to START (III): You hear nothing, or almost nothing. The engine's starter motor does not operate at all, or operates very slowly. You can hear the starter motor operating normally, or the starter motor sounds like it is spinning faster than normal, but the engine does not start up and run.
Main Menu Table of Contents If Your Engine Won't Start, Jump Starting To jump start your car, follow these The Starter Operates Normally Jump Starting directions closely: If your car's battery has run down, In this case, the starter motor's 03/07/10 31S5A930 0021 you may16:11:09 be able to start the engine speed sounds normal, or even faster 1. Open the hood and check the by using a booster battery.
Main Menu Table of Contents Jump Starting BOOSTER BATTERY 3. Connect one jumper cable to the positive ( +) terminal on the booster battery. Connect the other end to the positive ( +) terminal on your Honda's battery. 4. Connect the second jumper cable to the negative (—) terminal on the booster battery. Connect the other end to the grounding strap as shown. Do not connect this jumper cable to any other part of the engine. 5.
Main Menu Table of Contents If Your Engine Overheats The pointer of your car's tempera1. Safely pull to the side of the road. Your car can overheat for several ture gauge should stay in the midPut the transmission in Neutral or reasons, such as lack of coolant or a range under most conditions. It may Park and set the parking brake. mechanical problem. The only go higher if you are driving up a long Turn off the heating and cooling indication may be the temperature steep hill on a very hot day.
Main Menu Table of Contents If Your Engine Overheats 03/07/10 16:11:09 31S5A930 0021 4. If the temperature gauge stays at the red mark, turn off the engine. 5. Wait until you see no more signs of steam or spray, then open the hood. 6. Look for any obvious coolant leaks, such as a split radiator hose. Everything is still extremely hot, so use caution. If you find a leak, it must be repaired before you continue driving (see Emergency Towing on page 259). 7.
Main Menu Table of Contents Low Oil Pressure Indicator LOW OIL PRESSURE INDICATOR NOTICE Running the engine with low oil pressure can cause serious mechanical damage almost immediately. Turn off the engine as soon as you can safely get the car stopped. 1. Safely pull off the road and shut off the engine. Turn on the hazard warning indicators. This indicator should light when the ignition switch is ON (II), and go out after the engine starts. It should never come on when the engine is running.
Main Menu Table of Contents Charging System Indicator CHARGING SYSTEM INDICATOR This indicator should come on when the ignition switch is ON (II), and go out after the engine starts. If it comes on brightly when the engine is running, it indicates that the charging system has stopped charging the battery. Taking Care of the Unexpected Immediately turn off all electrical accessories: radio, heater, A/C, rear defogger, cruise control, etc.
Main Menu Table of Contents Malfunction Indicator Lamp MALFUNCTION INDICATOR LAMP This indicator comes on for a few seconds when you turn the ignition switch ON (II). If it comes on at any other time, it indicates one of the engine's emissions control systems may have a problem. Even though you may feel no difference in your car's performance, it can reduce your fuel economy and cause your car to put out excessive emissions. Continued operation may cause serious damage.
Main Menu Table of Contents Brake System Indicator BRAKE SYSTEM INDICATOR* "U.S. indicator shown The Brake System indicator light should normally come on only when the parking brake is not fully released. If it comes on at any other time, it indicates a problem with the car's brake system. In most cases, the problem is a low fluid level in the brake fluid reservoir. Press lightly on the brake pedal to see if it feels normal.
Main Menu Table of Contents Closing the Moonroof If the electric motor will not close the moonroof, do the following: ROUND PLUG SOCKET 1. Check the fuse for the moonroof motor (see page 255). If the fuse is blown, replace it with one of the same or lower rating. 2. Try closing the moonroof. If the new fuse blows immediately or the moonroof motor still does not operate, you can close the moonroof manually. 3. Get the moonroof wrench out of the tool kit in the trunk. 4.
Main Menu Table of Contents Fuses All the electrical circuits in your car have fuses to protect them from a short circuit or overload. These fuses are located in two or three fuse boxes. TAB UNDER-HOOD ABS FUSE BOX INTERIOR The under-hood fuse box is located in the engine compartment next to the battery. To open it, push the tab as shown. The interior fuse box is underneath the dashboard on the driver's side. Remove the fuse box lid by swinging the lid down and pulling it straight out of its hinges.
Main Menu Table of Contents Fuses Checking and Replacing Fuses If something electrical in your car stops working, the first thing you should check for is a blown fuse. Determine from the chart on pages 257 and 258 , or the diagram on the fuse box lid, which fuse or fuses control that component. Check those fuses first, but check all the fuses before deciding that a blown fuse is not the cause. Replace any blown fuses and check the component's operation. 1. Turn the ignition switch to LOCK (0).
Main Menu Table of Contents Fuses BLOWN If you replace the blown fuse with a spare fuse that has a lower rating, it might blow out again. This does not indicate anything wrong. Replace the fuse with one of the correct rating as soon as you can. NOTICE 5. Look for a burned wire inside the fuse. If it is burned, replace it with one of the spare fuses of the same rating or lower.
Main Menu Table of Contents Fuses INTERIOR FUSE BOX * : On Canadian models CONTINUED Taking Care of the Unexpected
Main Menu Table of Contents Fuses UNDER-HOOD FUSE BOX ABS FUSE BOX Taking Care of the Unexpected
Main Menu Table of Contents Emergency Towing If your car needs to be towed, call a professional towing service or, if you belong to one, an organization that provides roadside assistance. Never tow your car behind another vehicle with just a rope or chain. It is very dangerous. on the ends. These hooks go around parts of the frame or suspension and the cables lift that end of the car off the ground. Your car's suspension and body can be seriously damaged. This method of towing is unacceptable.
Main Menu Table of Contents Emergency Towing If you decide to tow your car with all four wheels on the groud, make sure you use a properly-designed and attached tow bar. Prepare the car for towing as described above, and leave the ignition switch in Accessory (I) so the steering wheel does not lock. Make sure the radio and any items plugged into the accessory power socket are turned off so they do not run down the battery. NOTICE The steering wheel system can be damaged if the steering wheel is locked.
Main Menu Technical Information The diagrams in this section give you the dimensions and capacities of your Honda, and the locations of the identification numbers. The explanations of several electronic and mechanical systems on your Honda are for the more technically-oriented owner. Identification Numbers................. 262 Specifications................................ . 264 DOT Tire Quality Grading (U.S. Cars)..............................266 Treadwear.................................. 266 Traction..
Main Menu Table of Contents Identification Numbers Your car has several identifying numbers located in various places. The Vehicle Identification Number (VIN) is the 17-digit number your Honda dealer uses to register your car for warranty purposes. It is also necessary for licensing and insuring your car. The easiest place to find the VIN is on a plate fastened to the top of the dashboard. You can see it by looking through the windshield on the driver's side.
Main Menu Table of Contents Identification Numbers The Engine Number is stamped into the engine block. TRANSMISSION NUMBER The Transmission Number is on a label on top of the transmission.
Main Menu Table of Contents Specifications Dimensions Capacities Weights Engine * 1 : U.S.: DX, DX Value Package, LX, Canada: LX, SE, EX * 2 : U.S.: EX Technical Information *1 : Including the coolant in the reserve tank and that remaining in the engine. Reserve tank capacity: 0.11 US gal (0.4 , 0 . 0 9 l m p g a l) * 2 : U.S.: DX, DX Value Package, LX, Canada: LX, SE, EX * 3 : U.S.: EX * 4 : Excluding the oil remaining in the engine.
Main Menu Table of Contents Specifications page 257 page 258 * 1 : Without moonroof *2 : With moonroof * 1 : U.S.: DX, LX, Canada: LX, SE * 2 : Canada: EX without ABS * 3 : U.S.
Main Menu Table of Contents DOT Tire Quality Grading (U.S. Cars) The tires on your car meet all U.S. Federal Safety Requirements. All tires are also graded for treadwear, traction, and temperature performance according to Department of Transportation (DOT) standards. The following explains these gradings. Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between the tread shoulder and the maximum section width.
Main Menu Table of Contents DOT Tire Quality Grading (U.S. Cars) Temperature The temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Main Menu Table of Contents Oxygenated Fuels Some conventional gasolines are being blended with alcohol or an ether compound. These gasolines are collectively referred to as oxygenated fuels. To meet clean air standards, some areas of the United States and Canada use oxygenated fuels to help reduce emissions. If you use an oxygenated fuel, be sure it is unleaded and meets the minimum octane rating requirement. Before using an oxygenated fuel, try to confirm the fuel's contents.
Main Menu Table of Contents Driving in Foreign Countries If you are planning to take your Honda outside the U.S. or Canada, contact the tourist bureaus in the areas you will be traveling in to find out about the availability of unleaded gasoline with the proper octane rating. If unleaded gasoline is not available, be aware that using leaded gasoline in your Honda will affect performance and fuel mileage, and damage its emissions controls. It will no longer comply with U.S.
Main Menu Table of Contents Emissions Controls The burning of gasoline in your car's engine produces several byproducts. Some of these are carbon monoxide (CO), oxides of nitrogen (NOx) and hydrocarbons (HC). Gasoline evaporating from the tank also produces hydrocarbons. Controlling the production of NOx, CO, and HC is important to the environment. Under certain conditions of sunlight and climate, NOx and HC react to form photochemical "smog.
Main Menu Table of Contents Emissions Controls Exhaust Emissions Controls The exhaust emissions controls include three systems: PGM-FI, Ignition Timing Control and Three Way Catalytic Converter. These three systems work together to control the engine's combustion and minimize the amount of HC, CO, and NOx that comes out the tailpipe. The exhaust emissions control systems are separate from the crankcase and evaporative emissions control systems.
Main Menu Table of Contents Three Way Catalytic Converter The three way catalytic converter contains precious metals that serve as catalysts, promoting chemical reactions to convert the exhaust gasses without affecting the metals. The catalytic converter is referred to as a three-way catalyst, since it acts on HC, CO, and NOx. A replacement unit must be an original Honda part or its equivalent. The three way catalytic converter must operate at a high temperature for the chemical reactions to take place.
Main Menu Warranty and Customer Relations Customer Relations Information................................. 274 U.S. Zone Office Map.................... 275 Canada Zone Office Map.............. 276 Warranty Coverages..................... 277 Reporting Safety Defects (U.S. Vehicles)........................... 278 Authorized Manuals......................
Main Menu Table of Contents Customer Relations Information Honda dealership personnel are trained professionals. They should be able to answer all your questions. If you encounter a problem that your dealership does not solve to your satisfaction, please discuss it with the dealership's management. The Service Manager or General Manager can help. Almost all problems are solved in this way.
Main Menu Table of Contents U.S. Zone Office Map ZONE 2 ZONE 8 ZONE 9 ZONE 4 ZONE 5 ZONE 10 ZONE 1 ZONE 6 ZONE 3 Mid-Atlantic Zone 902 Wind River Ln., Suite 200 Gaithersburg, Maryland 20878 (301)990-2020 Western Zone P.O. Box 2260 700 Van Ness Avenue Torrance, California 90509-2260 (310) 781-4565 ZONE 7 ZONE 15 ZONE 2 The addresses and telephone numbers are subject to change. If you cannot reach your Zone office, ask your Honda dealer for the current information. Northwestern Zone P.O.
Main Menu Table of Contents Canada Zone Office Map CUSTOMER RELATIONS RELATIONS AVEC LA CLIENTELE Honda Canada Inc. 715 Milner Avenue Toronto, ON M1B 2K8 Tel: 1-888-9-HONDA-9 Fax: Toll-free 1-877-939-0909 Toronto (416) 287-4776 Honda Canada Inc.
Main Menu Table of Contents Warranty Coverages U.S. Owners Your new Honda is covered by these warranties: New Car Limited Warranty — covers your new vehicle, except for the battery, emissions control systems and accessories, against defects in materials and workmanship. Emissions Control Systems Defects Warranty and Emissions Performance Warranty — these two warranties cover your vehicle's emissions control systems. Time, mileage, and coverage are conditional.
Main Menu Table of Contents Reporting Safety Defects (U.S. Vehicles) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying American Honda Motor Co., Inc.
Main Menu Table of Contents Authorized Manuals Purchasing Factory Authorized Manuals (U.S. only) The following publications covering the operation and servicing of your vehicle can be obtained from Helm Incorporated, either by filling out the attached form or, for credit card holders, calling the toll-free phone number on the form. For manuals prior to the year shown below, contact Helm Incorporated, P.O. Box 07280, Detroit, Michigan 48207, or call 1-800-782-4356.
Main Menu Table of Contents Authorized Manuals Service Manual: This manual covers maintenance and recommended procedures for repair to engine and chassis components. It is written for the Journeyman mechanic, but is simple enough for most mechanically-inclined owners to understand. Electrical Troubleshooting Manual: This manual complements the Service Manual by providing in-depth troubleshooting information for each electrical circuit in your vehicle.
Main Menu Index Accessories and Modifications.... 149 Accessories................................. 149 Additional Safety Precaution.... 150 Modifications............................. 150 ACCESSORY (Ignition Key Position)....................................... . 71 Accessory Power Socket................ 87 Adding Automatic Transmission Fluid........................................ 197 Brake Fluid................................. 198 Clutch Fluid................................ 199 Engine Coolant...........
Main Menu Index Belts, Seat..................................... 8, 42 Beverage Holder.............................. 86 Body Repairs.................................. 236 Brakes Anti-lock System (ABS)............ 167 Break-in, New Linings .............. 142 Fluid............................................ 198 Light, Burned-out...................... 223 Parking......................................... . 85 System Indicator.................. 55, 252 Wear Indicators.........................
Main Menu Index Clutch Fluid.................................... 199 CO in the Exhaust......................... 270 Cold Weather, Starting in............. 157 Compact Spare............................... 238 Consumer Information*................ 274 Controls, Instruments and.............. 51 Coolant Adding......................................... 191 Checking..................................... 147 Proper Solution.......................... 191 Replacing....................................
Main Menu Index Engine Overheating................................247 Specifications.............................264 Engine Speed Limiter....... 159, 163 Ethanol in Gasoline ....................... 268 Evaporative Emissions Controls.. 270 Exhaust Fumes................................ 49 Expectant Mothers, Use of Seat Belts by......................................... 19 Exterior, Cleaning the................... 232 Fabric, Cleaning............................. 234 Fan, Interior.............................
Main Menu Index Reminder Beeper......................... 61 Replacing Halogen Bulbs ......... 220 Turning on.................................... 61 Head Restraints...............................79 Heating and Cooling........................ 90 High Altitude, Starting at.............. 157 High-Low Beam Switch.................. 61 High-mount Brake Light............... 225 Hood Latch.....................................202 Hood, Opening the........................ 144 Horn.....................................
Main Menu Index Maintenance.................................. . 173 Owner Maintenance Checks.... 185 Record..................................183 -184 Required Indicator....................... 59 Safety...........................................174 Schedule..............................178 -182 Malfunction Indicator Lamp.. 56, 251 Manual Transmission.................... 158 Manual Transmission Fluid ......... 198 Meters, Gauges................................ 57 Methanol in Gasoline....................
Main Menu Index Radiator Overheating.................... 247 Radio/CD/Cassette Sound System ..............98, 107, 121 Rear End Towing........................... 259 Rear Lights, Bulb Replacement....................... 223, 224 Rear Seat, Folding........................... 80 Rear View Mirror............................. 83 Rear Window Defogger.................. 64 Reclining the Seat Backs................ 77 Recommended Shift Speeds ........ 159 Reminder Lights..............................
Main Menu Index Snow Tires......................................216 Solvent-type Cleaners.................... 232 Sound System...................98, 107, 121 Spare Tire Inflating....................................... 238 Specifications............................. 265 Spark Plugs, Replacing................. 203 Specifications Charts..................... 264 Speed Control................................... 66 Speedometer................................... . 57 Spotlights....................................
Main Menu Index Transmission Checking Fluid Level, Automatic............................... 197 Checking Fluid Level, Manual....................................198 Fluid Selection...................197, 198 Identification Number............... 263 Shifting the Automatic.............. 160 Shifting the Manual................... 158 Treadwear...................................... 266 Trip Meter....................................... . 57 Trunk................................................ . 76 Opening......
Main Menu Service Information Summary Gasoline: Unleaded gasoline, pump octane number of 86 or higher. Fuel Tank Capacity: 11.9 US gal (45 l ,9.9 Imp gal) Recommended Engine Oil: API Service SJ "Energy Conserving" oil, SAE 5W-30 viscosity (see page 187). Oil change capacity (including filter): U.S. DX, DX Value Package, LX, Canada LX, SE, EX 3.8 US qt (3.6 l , 3.2 Imp qt) U.S. EX 3.5 US qt (3.3 l , 2.