2000 Civic Coupe Online Reference Owner's Manual Use these links (and links throughout this manual) to navigate through this reference. For a printed owner's manual, click on authorized manuals or go to www.helminc.com. Contents Owner's identification Introduction ..................................................................................................................................................... i A Few Words About Safety ...................................................................
Main Menu Owner's Identification This Owner's Manual should be considered a permanent part of the car, and should remain with the car when it is sold. OWNER ADDRESS STREET CITY STATE/PROVINCE ZIP CODE/ POSTAL CODE V. I. N. DELIVERY DATE (Date sold to original retail purchaser) DEALER NO.
Main Menu Introduction Congratulations ! Your selection of a 2000 Honda Civic was a wise investment. It will give you years of driving pleasure. One of the best ways to enhance the enjoyment of your new Honda is to read this manual. In it, you will learn how to operate its driving controls and convenience items. Afterwards, keep this owner's manual in your car so you can refer to it at any time. Several warranties protect your new Honda.
▼ ▲ Main Menu Main Menu A Few Words About Safety A Few Words About Safety Your safety, and the safety of others, Your safety, and the safety of others, is very important. And operating this is very important. operating this vehicle safely is anAnd important car safely is an important responsibility. responsibility.
Main Menu Your Car at a Glance HEATING/COOLING CONTROLS (P. 88) MIRROR CONTROLS (P. 82) DOOR LOCK SWITCHES (P. 70) POWER WINDOW SWITCHES (P. 79) FUEL FILL DOOR RELEASE (P. 125) TRUNK RELEASE HANDLE (P. 75) HOOD RELEASE HANDLE (P. 126) AUDIO SYSTEM, DIGITAL CLOCK (P.
Main Menu Your Car at a Glance CRUISE CONTROL (P. 66) INSTRUMENT PANEL BRIGHTNESS (P. 62) WINDSHIELD WIPERS/ HAZARD WARNINR WASHERS LIGHTS (P. 64) MOONROOF (P. 81) MIRROR CONTROLS (P. 82) HEADLIGHTS/ TURN SIGNALS (P. 61) TILT ADJUSTMENT (P. 65) HORN REAR WINDOW DEFOGGER (P.
Main Menu 4
Main Menu Driver and Passenger Safety This section gives you important information about how to protect yourself and your passengers. It shows you how to use seat belts properly. It explains your Supplemental Restraint System. And it tells you how to properly restrain infants and children in your car. Important Safety Precautions.......... 6 Your Car's Safety Features.............. 7 Seat Belts........................................8 Airbags............................................
Main Menu Table of Contents Important Safety Precautions You'll find many safety recommendations throughout this section, and throughout this manual. The recommendations on this page are the ones we consider to be the most important. Always Wear Your Seat Belt A seat belt is your best protection in all types of collisions. Airbags supplement seat belts, but airbags are designed to inflate only in a moderate to severe frontal collision.
Main Menu Table of Contents Your Car's Safety Features Your car is equipped with many features that work together to protect you and your passengers during a crash. Some safety features do not require any action on your part. These include a strong steel framework that forms a safety cage around the passenger compartment; front and rear crush zones that are designed to crumple and absorb energy during a crash; and a collapsible steering column.
Main Menu Table of Contents Your Car's Safety Features 03/07/10 Seat Belts For your safety, and the safety of your passengers, your car is equipped with seat belts in all seating positions. Your seat belt system also includes a light on the instrument panel to remind you and your passengers to fasten your seat belts. Why Wear Seat Belts Seat belts are the single most effective safety device for adults and larger children. (Infants and smaller children must be properly restrained in child seats.
Main Menu Table of Contents Your Car's Safety Features Airbags The most important things you need to know about your airbags are: Airbags do not replace seat belts. The seat belts are the occupants' primary protection in all types of collisions. The airbags supplement the seat belts by providing extra protection for the head and chest of each front seat occupant in a moderate to severe frontal collision.
Main Menu Table of Contents Your Car's Safety Features Seats & Seat-Backs Your car's seats are designed to keep you in a comfortable, upright position so you can take full advantage of the protection offered by seat belts and the energy absorbing materials in the seats. How you adjust your seats and seatbacks can also affect your safety.
Main Menu Table of Contents Your Car's Safety Features Door Locks Keeping your doors locked reduces the chance of being thrown out of the car during a crash. It also helps prevent occupants from accidentally opening a door and falling out, and outsiders from unexpectedly opening your doors.
Main Menu Table of Contents Protecting Adults Introduction The following pages provide instructions on how to properly protect the driver and other adult occupants. especially a child, will open a door while the car is moving and accidentally fall out. It also reduces the chance of someone being thrown out of the car during a crash. These instructions also apply to children who have outgrown child seats and are large enough to wear lap/shoulder belts.
03/07/10 16:11:09 31S5A930 Main Menu Table of Contents 0021 Protecting Adults 3. Adjust the Seat-Backs Sitting too close to an airbag can result in serious injury or death if the airbags inflate. Always sit as far back from the airbags as possible. Most shorter drivers can get far enough away from the steering wheel and still reach the pedals. However, if you are concerned about sitting too close, we recommend that you investigate whether some type of adaptive equipment may help.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Protecting Adults 4.Adjust the Head Restraints Improperly positioning head restraints reduces their effectiveness and you can be seriously injured in a crash. Make sure head restraints are in place and positioned properly before driving. Before driving, make sure everyone with an adjustable head restraint has properly positioned the head restraint.
Main Menu Table of Contents Protecting Adults 5. Fasten and Position the Seat Belts Using a Lap/Shoulder Belt Insert the latch plate into the buckle, then tug on the belt to make sure the belt is securely latched. Also check that the belt is not twisted, because a twisted belt can cause serious injuries in a crash.
Main Menu Table of Contents Protecting Adults Never place the shoulder portion of a lap/shoulder belt under your arm or behind your back. This could cause very serious injuries in a crash. Using the Lap Belt Insert the latch plate into the buckle marked CENTER. Driver and Passenger Safety If the belt is too short, hold the latch plate at a right angle and pull on the plate to extend the belt. Then insert the latch plate into the buckle, and tug on the belt to make sure the belt is securely latched.
Main Menu Table of Contents Protecting Adults If a Seat Belt Doesn't Work Properly If a seat belt does not seem to work as it should, it may not protect the occupant in a crash. No one should sit in a seat with an inoperative seat belt. Anyone using a seat belt that is not working properly can be seriously injured or killed. Have your Honda dealer check the belt as soon as possible. See page 42 for additional information about your seat belt system and how to take care of your belts.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0 Protecting Adults 6.Adjust the Steering Wheel Adjust the steering wheel, if needed, so that the wheel points toward your chest, not toward your face. Pointing the steering wheel toward your chest provides optimal protection from the airbag. See page 65 for how to adjust the steering wheel. Driver and Passenger Safety 7.
Main Menu Table of Contents Protecting Adults Advice for Pregnant Women Pregnant women should also sit upright and as far back as possible from the steering wheel or dashboard. This will reduce the risk of injuries to both the mother and her unborn child that can be caused by a crash or an inflating airbag. Each time you have a check-up, ask your doctor if it's okay for you to drive.
Main Menu Table of Contents Protecting Adults Do not place hard or sharp objects between yourself and an airbag. Carrying hard or sharp objects on your lap, or driving with a pipe or other sharp object in your mouth, can result in injuries if your airbags inflate. Do not attach or place objects on the airbag covers. Any object attached to or placed on the covers marked "SRS AIRBAG," in the center of the steering wheel and on top of the dashboard, could interfere with the proper operation of the airbags.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Protecting Children Children who are unrestrained or improperly restrained can be seriously injured or killed in a crash. Any child too small for a seat belt should be properly restrained in a child seat. A larger child should be properly restrained with a seat belt. Children depend on adults to protect them. However, despite their best intentions, many parents and other adults may not know how to properly protect young passengers.
Main Menu Table of Contents Protecting Children Children Should Sit in the Back Seat According to accident statistics, children of all ages and sizes are safer when they are restrained in the back seat, not the front seat. The National Highway Traffic Safety Administration and Transport Canada recommend that all children ages 12 and under be properly restrained in the back seat. In the back seat, children are less likely to be injured by striking hard interior parts during a collision or hard braking.
Main Menu Table of Contents Protecting Children U.S. Models To remind you of the passenger's airbag hazards, and that children must be properly restrained in the back seat, your car has warning labels on the dashboard and on the driver's and front passenger's visors. Please read and follow the instructions on these labels. Canadian Models To remind you of the airbag hazards, your car has warning labels on the driver's and front passenger's visors.
Main Menu Table of Contents Protecting Children If You Must Drive with Several Children Your car has three seating positions in the back seat where children can be properly restrained. If you ever have to carry more than three children in your car: Place the largest child in the front seat, provided the child is large enough to wear a seat belt properly (see page 37 ). Move the vehicle seat as far to the rear as possible (see page 12 ). Have the child sit upright and well back in the seat (see page 18).
Main Menu Table of Contents Protecting Children General Guidelines for Using Child Seats The following pages give general guidelines for selecting and installing child seats for infants and small children. Selecting a Child Seat To provide proper protection, a child seat should meet three requirements: 1. The child seat should meet safety standards. The child seat should meet Federal Motor Vehicle Safety Standard 213 (FMVSS 213) or Canadian Motor Vehicle Safety Standard 213 (CMVSS 213).
Main Menu Table of Contents Protecting Children 3. The child seat should fit the vehicle seating position (or positions) where it will be used. Due to variations in the design of child seats, vehicle seats, and seat belts, all child seats will not fit all vehicle seating positions. However, Honda is confident that one or more child seat models can fit and be properly installed in all recommended seating positions in your car.
Main Menu Table of Contents Protecting Children Placing a Child Seat This page briefly summarizes Honda's recommendations on where to place rear-facing and forwardfacing child seats in your car. Airbags Pose Serious Risks to Children The passenger's airbag inflates with enough force to kill or seriously injure an infant in a rear-facing child seat. A small child in a forward-facing child seat is also at risk.
Main Menu Table of Contents Protecting Children Installing a Child Seat To provide security during normal driving maneuvers as well as during a collision, we recommend that parents secure a child seat as firmly as possible. 1. Secure the child seat to the car with a seat belt. All child seats must be secured to the car with the lap belt or the lap part of a lap/ shoulder belt. A child whose seat is not properly secured to the car can be endangered in a crash.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Protecting Children Protecting Infants Rear-Facing Child Seat Placement Placing a rear-facing child seat in the front seat can result in serious injury or death if the airbags inflate. Always place a rear-facing child seat in the back seat, not the front. Child Seat Type Only a rear-facing child seat provides proper support for a baby's head, neck, and back. Infants up to about one year of age must be restrained in a rear-facing child seat.
Main Menu Table of Contents Protecting Children Installing a Rear-Facing Child Seat with a Lap/Shoulder Belt The lap/shoulder belts in the outer back seats have a locking mechanism that must be activated to secure a child seat. See page 32 for how to secure a rearfacing child seat in the center back seat with the lap belt. For tips on installing a rear-facing child seat with a seat belt, see page 32.
Main Menu Table of Contents Protecting Children 2. To activate the lockable retractor, slowly pull the shoulder part of the belt all the way out until it stops, then let the belt feed back into the retractor (you might hear a clicking noise as the belt retracts). 3. After the belt has retracted, tug on it. If the belt is locked, you will not be able to pull it out. If you can pull the belt out, it is not locked and you will need to repeat these steps. 4.
Main Menu Table of Contents Protecting Children Installing a Rear-Facing Child Seat with the Lap Belt To install a rear-facing child seat in the center back seat with the lap belt, follow instruction number 1 on page 30 for routing and latching the seat belt. Then pull hard on the loose end of the belt to remove any slack (it may help to put weight on the child seat while pulling on the belt). Finally, follow instruction number 5 on page 31 to verify that the child seat is secure.
Main Menu Table of Contents Protecting Children Additional Precautions for Infants Never hold an infant on your lap. Protecting Small Children If you are not wearing a seat belt in a crash, you could be thrown forward into the dashboard and crush the infant. Child Seat Placement In this car, the best place to install a forward-facing child seat is in one of the seating positions in the back seat. If you are wearing a seat belt, the infant can be torn from your arms.
Main 16:11:09 Menu Table of Contents 03/07/10 31S5A930 0021 Protecting Children Improperly placing a forwardfacing child seat in the front seat can result in serious injury or death if the airbags inflate. If you must place a forwardfacing child seat in front, move the vehicle seat as far back as possible and properly restrain the child.
Main Menu Table of Contents Protecting Children 2. To activate the lockable retractor, slowly pull the shoulder part of the belt all the way out until it stops, then let the belt feed back into the retractor (you might hear a clicking noise as the belt retracts). 3. After the belt has retracted, tug on it. If the belt is locked, you will not be able to pull it out. If you can pull the belt out, it is not locked and you will need to repeat these steps. 4.
Main Menu Table of Contents Protecting Children To deactivate the locking mechanism in order to remove a child seat, unlatch the buckle, unroute the seat belt, and let the belt fully retract. Installing a Child Seat with the Lap Belt Never hold a small child on your lap. If you are not wearing a seat belt in a crash, you could be thrown forward into the dashboard and crush the child.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Protecting Children Protecting Larger Children When a child reaches the recommended weight or height limit for a forward-facing child seat, the child should sit in one of the outer back seats and wear a lap/shoulder belt. The lap/shoulder belt provides better protection than the lap belt.
Main Menu Table of Contents Protecting Children However, if the belt touches or crosses the child's neck, the child needs to use a booster seat. Do not let a child wear a seat belt across the neck.This could result in serious neck injuries during a crash. If the shoulder part of the belt rests over the child's collarbone and against the center of the chest, as shown, the child is large enough to wear the seat belt.
Main Menu Table of Contents Protecting Children Using a Booster Seat A child may continue using a booster seat until the tops of the ears are even with the top of the seat-back. A child of this height should be tall enough to use the lap/shoulder belt without a booster. When Can a Larger Child Sit in Front The National Highway Traffic Safety Administration and Transport Canada recommend that all children ages 12 and under be properly restrained in a back seat.
Main Menu Table of Contents Protecting Children Physical Size Physically, a child must be large enough for the lap/shoulder belt to properly fit over the hips, chest, and shoulder (see pages 15 and 21). If the seat belt does not fit properly, the child should not sit in the front. Maturity To safely ride in front, a child must be able to follow the rules, including sitting properly and wearing the seat belt properly throughout a ride.
Main Menu Table of Contents Protecting Children Attach the tether strap hook to the tether anchorage point and tighten the strap according to the child seat maker's instructions.
Main Menu Table of Contents Additional Information About Your Seat Belts Seat Belt System Components Your seat belt system includes lap/ shoulder belts in the front seats and the outer back seats, and a lap belt in the center back seat. The seat belt system also includes a light on the instrument panel to remind you and your passengers to fasten your belts. If the driver's seat belt is not fastened before the ignition is turned ON (II), the light will come on and a beeper will also sound.
Main Menu Table of Contents Additional Information About Your Seat Belts To deactivate the locking mechanism, unlatch the buckle and let the seat belt fully retract. To refasten the belt, pull it out only as far as needed. Lap Belt The lap belt has one manuallyadjusted belt that fits across the hips. See page 15 for instructions on how to wear the lap/shoulder belt properly.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Additional Information About Your Seat Belts Seat Belt Maintenance For safety, you should check the condition of your seat belts regularly. Pull each belt out fully and look for frays, cuts, burns, and wear. Check that the latches work smoothly and that the lap/shoulder belts retract easily. Any belt not in good condition or not working properly will not provide good protection and should be replaced as soon as possible. U.S.
Main Menu Table of Contents Additional Information About Your SRS SRS Components Your Supplemental Restraint System (SRS) includes: Two front airbags. The driver's airbag is stored in the center of the steering wheel; the front passenger's airbag is stored in the dashboard. Both are marked "SRS AIRBAG." Sensors that can detect a moderate to severe frontal collision.
Main Menu Table of Contents Additional Information About Your SRS Since both airbags use the same sensors, both airbags normally inflate at the same time. However, it is possible for only one airbag to inflate. This can occur when the severity of a collision is at the margin, or threshold, that determines whether or not the airbags will deploy. In such cases, the seat belt will provide sufficient protection, and the supplemental protection offered by the airbag would be minimal.
Main Menu Table of Contents Additional Information About Your SRS How the SRS Indicator Light If the light comes on or flashes on Works and off while you drive. The purpose of the SRS 16:11:09 31S5A930 SRS light is to alert you to a03/07/10 If you see any of these indications, potential problem with your your airbags may not deploy when Supplemental Restraint System. you need them. See your Honda dealer as soon as possible.
Main Menu Table of Contents Additional Information About Your SRS Additional Safety Precautions Do not attempt to deactivate your airbags. Together, airbags and seat belts provide the best protection in a moderate to severe frontal collision. Do not tamper with SRS components or wiring for any reason. Tampering could cause the airbags to deploy, possibly causing very serious injury. See page 131 for further information and precautions relating to your SRS.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Carbon Monoxide Hazard Your car's exhaust contains carbon monoxide gas. You should have no problem with carbon monoxide entering the car in normal driving if you maintain your car properly. Have the exhaust system inspected for leaks whenever: The car is raised for an oil change. You notice a change in the sound of the exhaust. The car was in an accident that may have damaged the underside. Carbon monoxide gas is toxic.
Main Menu Table of Contents Safety Labels These labels are in the locations shown. They warn you of potential hazards that could cause serious injury. Read these labels carefully. DASHBOARD U.S. models only SUN VISOR U.S. models If a label comes off or becomes hard to read, contact your Honda dealer for a replacement.
Main Menu Instruments and Controls This section gives information about the controls and displays that contribute to the daily operation of your Honda. All the essential controls are within easy reach. Control Locations............................ 52 Indicator Lights................................ 53 Gauges............................................. . 57 Speedometer................................ 57 Tachometer................................. . 57 Odometer..................................... .
Main Menu Table of Contents Control Locations MIRROR CONTROLS (P. 82) HEATING/COOLING CONTROLS (P. 88) DOOR LOCK SWITCHES (P- 70) POWER WINDOW SWITCHES (P. 79) FUEL FILL DOOR RELEASE (P. 125) TRUNK RELEASE HANDLE (P. 75) Instruments and Controls HOOD RELEASE HANDLE (P. 126) AUDIO SYSTEM, DIGITAL CLOCK (P.
Main Menu Table of Contents Indicator Lights The instrument panel has many indicators to give you important information about your car. U.S.: EX, Canada: Si Instrument Panel CHARGING SYSTEM INDICATOR PARKING BRAKE AND BRAKE SYSTEM INDICATOR* MALFUNCTION INDICATOR LAMP TRUNK-OPEN INDICATOR LOW OIL PRESSURE INDICATOR LOW FUEL INDICATOR CRUISE CONTROL INDICATOR SUPPLEMENTAL RESTRAINT SYSTEM INDICATOR HIGH BEAM INDICATOR SEAT BELT REMINDER LIGHT ANTI-LOCK BRAKE SYSTEM INDICATOR* * The U.S.
Main Menu Table of Contents Indicator Lights U.S.: DX, Canada: DX HIGH BEAM INDICATOR CHARGING SYSTEM INDICATOR Seat Belt Reminder Light PARKING BRAKE AND BRAKE SYSTEM INDICATOR" TRUNK-OPEN INDICATOR LOW OIL PRESSURE INDICATOR LOW FUEL INDICATOR This indicator lights when you turn the ignition switch ON (II). It is a reminder to you and your passengers to protect yourselves by fastening the seat belts. A beeper also sounds if you have not fastened your seat belt.
Main Menu Table of Contents Indicator Lights Charging System Indicator If this light comes on when the engine is running, the battery is not being charged. For complete information, see page 232 . Low Oil Pressure Indicator The engine can be severely damaged if this light flashes or stays on when the engine is running. For complete information, see page 231. High Beam Indicator This light comes on with the high beam headlights. See page 61 for information on the headlight controls.
Main Menu Table of Contents Indicator Lights Turn Signal and Hazard Warning Indicators The left or right turn signal light blinks when you signal a lane change or turn. If the light does not blink or blinks rapidly, it usually means one of the turn signal bulbs is burned out (see page 205 ). Replace the bulb as soon as possible, since other drivers cannot see that you are signalling. When you turn on the Hazard Warning switch, both turn signal lights blink.
Main Menu Table of Contents Gauges U.S.: EX, Canada: Si Instrument Panel TACHOMETER TRIP METER ODOMETER SPEEDOMETER FUEL GAUGE TEMPERATURE GAUGE MAINTENANCE REQUIRED INDICATOR Speedometer U.S. Models This shows your speed in miles per hour (mph). The smaller inner numbers are the speed in kilometers per hour (km/h). Canadian Models This shows your speed in kilometers per hour (km/h). The smaller inner numbers are the speed in miles per TRIP METER RESET BUTTON hour (mph).
Main Menu Table of Contents Gauges DX Instrument Panel TEMPERATURE GAUGE TRIP METER ODOMETER SPEEDOMETER MAINTENANCE REQUIRED INDICATOR (U.S. Cars only) Fuel Gauge This shows how much fuel you have. It is most accurate when the car is on level ground. It may show slightly more or less than the actual amount when you are driving on curvy or hilly roads. Instruments and Controls FUEL GAUGE TRIP METER RESET BUTTON The gauge stays at the same fuel level reading after you turn off the ignition.
Main Menu Table of Contents Gauges Maintenance Required Indicator SLOT INDICATOR When the distance driven since the last scheduled maintenance nears 7,500 miles (12,000 km), the indicator will turn yellow. If you exceed 7,500 miles (12,000 km), the indicator will turn red. Your dealer will reset the indicator when he performs the scheduled maintenance. If someone else performs the maintenance, reset the indicator by inserting your key in the slot beside the indicator. U.S.
Main Menu Table of Contents Controls Near the Steering Wheel The two levers on the steering column contain controls for driving features you use most often. The left lever controls the turn signals, headlights, and high beams. The right lever controls the windshield washers and wipers. CRUISE CONTROL INSTRUMENT PANEL BRIGHTNESS HAZARD WARNING LIGHTS REAR WINDOW DEFOGGER MOONROOF The rear window defogger switch is on the dashboard to the right of the center air vents.
Main Menu Table of Contents Controls Near the Steering Wheel Headlights The rotating switch on the left lever controls the lights. Turning this switch to the position turns on the parking lights, taillights, instrument panel lights, side-marker lights, and rear license plate lights. Turning the switch to the position turns on the headlights. If you leave the lights on with the ignition switch in ACCESSORY (I) or LOCK (0), you will hear a reminder beeper when you open the driver's door.
Main Menu Table of Contents Controls Near the Steering Wheel Instrument Panel Brightness Turn Signals TURN SIGNAL LEVER The dial on the dashboard to the left of the instrument panel controls the brightness of the instrument panel lights. Turn the dial to adjust the brightness. Instruments and Controls Signal a turn or lane change with this lever. Push down on the lever to signal a left turn, and up to signal a right turn.
Main Menu Table of Contents Controls Near the Steering Wheel Windshield Wipers The right lever controls the windshield wipers and washers. The rotary switch at the end of the lever has three positions: INT: intermittent : low speed : high speed In intermittent, the wipers operate every few seconds. In low speed and high speed, the wipers run continuously. Windshield Washers To operate the wipers in mist mode, push the control lever down. The wipers run at high speed until you release the lever.
Main Menu Table of Contents Controls Near the Steering Wheel Hazard Warning Rear Window Defogger Make sure the rear window is clear and you have good visibility before starting to drive. The defogger wires on the inside of the rear window can be accidentally damaged. When cleaning the glass, always wipe side to side. Push the red button to the left of the center vents to turn on the hazard warning lights (four-way flashers).
Main Menu Table of Contents Controls Near the Steering Wheel Steering Wheel Adjustment 3. Push the lever up to lock the steering wheel in that position. Make any steering wheel adjustment before you start driving. 4. Make sure you have securely locked the steering wheel in place by trying to move it up and down. See page 18 for important safety 03/07/10 16:11:09 31S5A930 0021 information about how to properly position the steering wheel.
Main Menu Table of Contents Steering Wheel Controls Cruise Control NOTICE On EX and Si models in the U.S., and Si The cruise control, as it operates, and SiR models in Canada moves the accelerator pedal. You can Cruise control allows you to maintain damage your car's accelerator a set speed above 25 mph (40 km/h) mechanism by resting your foot under without keeping your foot on the the pedal and blocking the movement. accelerator pedal. It should be used for cruising on straight, open highways.
Main Menu Table of Contents Steering Wheel Controls cruise control. To resume the set speed, press and hold the RESUME/accel button until the CRUISE CONTROL light on the instrument panel comes on. When climbing a steep hill, the automatic transmission may downshift to hold the set speed. Changing the Set Speed RESUME/ accel SET/decel 3. Press and release the SET/decel button on the steering wheel. The CRUISE CONTROL light on the instrument panel comes on to show the system is now activated.
Main Menu Table of Contents Steering Wheel Controls Even with the cruise control turned on, you can still use the accelerator pedal to speed up for passing. After completing the pass, take your foot off the accelerator pedal. The car will return to the set cruising speed. Resting your foot on the brake or clutch pedal will cause the cruise control to cancel. Cancelling the Cruise Control You can cancel the cruise control in any of these ways: Tap the brake or clutch pedal.
Main Menu Table of Contents Keys and Locks Keys KEY NUMBER PLATE MASTER KEYS VALET KEY The valet key works only in the ignition and the door locks. You can keep the trunk, trunk release handle, trunk pass-through cover, rear seat trunk access and glove box locked when you leave your car and the valet key at a parking facility. Ignition Switch You should have received a key number plate with your set of keys. You will need this key number if you ever have to get a lost key replaced.
Main Menu Table of Contents Keys and Locks LOCK (0) — You can insert or remove the key only in this position. To switch from ACCESSORY to LOCK, you must push the key in slightly as you turn it. If your car has an automatic transmission, the shift lever must also be in Park. The antitheft lock will lock the steering column when you remove the key. If the front wheels are turned, the anti-theft lock may sometimes make 03/07/10 16:11:09 31S5A930 it difficult to turn the key from LOCK to ACCESSORY.
Main Menu Table of Contents Keys and Locks Power Door Locks Both doors lock when you push the lock tab on the driver's door in, or lock the driver's door from the outside with the key. Only the driver's door unlocks when you use the key or lock tab. To unlock the passenger's door, use the master door lock switch or the lock tab on the passenger's door. MASTER DOOR LOCK SWITCH The doors can also be locked and unlocked from the outside with the key. On HX, EX and Si models in the U.S.
Main Menu Table of Contents Keys and Locks Remote Transmitter LED lights, and taillights flash twice. LOCK BUTTON UNLOCK BUTTON PANIC BUTTON On EX and Si models in the U.S. You can lock and unlock your car with the remote transmitter. When you push the LOCK button, all doors lock. The parking lights, side marker lights, and taillights flash once. When you push the UNLOCK button once, only the driver's door unlocks. The passenger's door unlocks when you push the button a second time.
Main Menu Table of Contents Keys and Locks Replacing the Battery ROUND COVER Open CUSHION RING BATTERY Close When the remote transmitter's battery begins to get weak, it may take several pushes on the button to lock or unlock the doors, and the LED will get dim. Replace the battery as soon as possible. Battery type: CR2025 To replace the battery, remove the round cover on the back of the transmitter by turning it counterclockwise with a coin. Reinstall the O-ring.
Main Menu Table of Contents Keys and Locks Transmitter Care Avoid severe shock to the transmitter, such as dropping or throwing it. Also, protect it from extreme hot or cold temperatures. Clean the transmitter case with a soft cloth. Do not use strong cleaners or solvents that could harm the case. Immersing the transmitter in any liquid will harm the transmitter and cause it to not function properly. Use the ring on the transmitter to attach it to your main key ring.
Main Menu Table of Contents Keys and Locks Trunk TRUNK RELEASE HANDLE You can open the trunk in two ways: Pull the trunk release handle to the left of the driver's seat. Use the master key to open the trunk lock. The valet key does not work in this lock. MASTER KEY To close the trunk, press down on the trunk lid. See page 133 for cargo loading and weight limit information.
Main Menu Table of Contents Seat Adjustments Front Seat Adjustments See pages 12 —13 for important safety informationand warnings about how to properly position seats and seat-backs. Make all seat adjustments before you start driving. To adjust the seat forward and backward, pull up on the lever under the seat cushion's front edge. Move the seat to the desired position and release the lever. Try to move the seat to make sure it is locked in position.
Main Menu Table of Contents Seat Adjustments Rear Scat Access RELEASE LEVER On HX, EX and Si models in the U.S., and DX, Si and SiR models in Canada Push the passenger's seat-back while pushing the release lever to tilt the seat-back out of the way. The entire seat will slide forward at the same time. Head Restraints RELEASE BUTTON To get into the back seat on the driver's side, pull up on the seat-back adjustment lever.
Main Menu Table of Contents Seat Adjustments, Folding Rear Seat The front head restraints adjust for height. You need both hands to adjust the restraint. Do not attempt to adjust it while driving. To raise it, pull upward. To lower the restraint, push the release button sideways and push the restraint down. To remove a head restraint for cleaning or repair, pull it up as far as it will go. Push the release button and pull the restraint out of the seatback.
Main Menu Table of Contents Folding Rear Seat, Power Windows RELEASE To release the seat-back from inside the trunk, pull the release under the rear shelf. Push the seat-back down, then let go of the release. Make sure all items in the trunk, or items extending through the opening into the back seat, are secured. Loose items can fly forward and cause injury if you have to brake hard. See Carrying Cargo on page 132. Power Windows On HX, EX and Si models in the U.S.
Main Menu 03/07/10 16:11:09 31S5A930 0021 Table of Contents Power Windows DRIVER'S WINDOW SWITCH Closing a power window on someone's hands or fingers can cause serious injury. Make sure your passengers are away from the windows before closing them. MAIN SWITCH On HX, EX and Si models in the U.S., Si and SiR models in Canada The driver's door has a master power window control panel. To open the passenger's window, push down on the switch and hold it down until the window reaches the desired position.
Main Menu Table of Contents Moonroof, Mirrors 03/07/10 Moonroof 16:11:09 31S5A930 position, then release the switch. To close the moonroof, press and hold the switch. 0021 Mirrors Closing the moonroof on someone's hands or fingers can cause serious injury. Make sure passengers are clear of the moonroof before closing it. On EX and Si models in the U. S., and Si and SiR models in Canada Use the switches on the dashboard under the left vent to operate the moonroof. The ignition must be ON (II).
Main Menu Table of Contents Mirrors Adjusting the Power Mirrors SELECTOR SWITCH On HX, EX and Si models in the U.S., Si and SiR models in Canada Adjust the outside mirrors with the adjustment switch on the left side of the dashboard: 1. Turn the ignition switch ON (II). 2. Move the selector switch to L (driver's side) or R (passenger's side). Instruments and Controls ADJUSTMENT SWITCH 3. Push the appropriate edge of the adjustment switch to move the mirror right, left, up or down. 4.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 Parking Brake, Glove Box Parking Brake Glove Box An open glove box can cause serious injury to your passenger in a crash, even if the passenger is wearing the seat belt. Always keep the glove box closed while driving. PARKING BRAKE LEVER To apply the parking brake, pull the lever up fully. To release it, pull up slightly, push the button, and lower the lever.
Main Menu Table of Contents Beverage Holder Be careful when you are using the beverage holder. A spilled liquid that is very hot can scald you or your passengers. Spilled liquids can also damage the upholstery, carpeting, and electrical components in the interior. The inner liner can be removed if you want to hold a larger cup.
Main Menu Table of Contents Accessory Power Socket, Ashtrays Accessory Power Socket This socket is intended to supply power for 12 volt DC accessories that are rated 120 watts or less (10 amps). It will not power an automotive type cigarette lighter element. Ashtrays (Optional) Front and rear ashtrays are available as options. The front ashtray fits in the beverage holder. The rear ashtray fits in the rear of the center armrest. Open the rear ashtray by swinging the upper edge down.
Main Menu Table of Contents Interior Light (U.S.: EX and Si, Canada: Si and SiR) DOOR ACTIVATED ON (U.S.: EX and Si, Canada: Si and SiR) (U.S.: DX, HX, Canada: DX) OFF OFF ON DOOR ACTIVATED The interior light has a threeposition switch. In the OFF position, the light does not come on. In the center position, the interior light comes on when you open any door. In the ON position, the interior light stays on continuously.
Main Menu Comfort and Convenience Features The heating and air conditioning* systems in your Honda provide a comfortable driving environment in all weather conditions. The standard audio system has many features. This section describes those features and how to use them. (If you selected an optional audio system, refer to the operating instructions that came with it.) * Air conditioning is standard on the EX and Si models in the U.S. and on SiR model in Canada. It is optional on other models.
Main Menu Table of Contents Heating and Cooling Proper use of the Heating and Cooling system can make the interior dry and comfortable, and keep the windows clear for best visibility. If your car does not have air conditioning, it can be installed at any time. Your dealer can install a Genuine Honda air conditioning system that meets Honda's high quality standards and is designed to exactly fit your car. Please contact your dealer for more information.
Main Menu Table of Contents Heating and Cooling Mode Control Dial Use the MODE control dial to select the vents the air flows from. Some air will flow from the dashboard vents in all modes. Air flows from the center and corner vents in the dashboard. Air flow is divided between the vents in the dashboard and the floor vents. vents. Air flows from the floor Air flow is divided between the floor vents and the defroster vents at the base of the windshield.
Main Menu Table of Contents Heating and Cooling Vent Controls CENTER VENT SIDE VENT Open Close You can adjust the direction of the air coming from the dashboard vents by moving the tab in the center of each vent up-and-down and side-toside. Comfort and Convenience Features The vents in the corners of the dashboard can be opened and closed with the dials next to them.
Main Menu Table of Contents Heating and Cooling It is best to leave the system in Fresh Air mode under almost all conditions. Keeping the system in Recirculation mode, particularly with the A/C off, can cause the windows to fog up. Switch to Recirculation mode when you are driving through smoky or dusty conditions, then switch back to Fresh Air mode when the condition clears. The outside air intakes for the heating and cooling system are at the base of the windshield.
Main Menu Table of Contents Heating and Cooling To Cool with A/C 1. Turn on the A /C by pressing the button. The light in the button should come on when a fan speed is selected. 2. Make sure the temperature control dial is all the way to the left. 3. Select 4. If the outside air is humid, select Recirculation mode. If the outside air is dry, select Fresh Air mode. 5. Set the fan to the desired speed.
Main Menu Table of Contents Heating and Cooling To Heat To warm the interior: 1. Start the engine. 2. Select and Fresh Air mode. 3. Set the fan to the desired speed. 4. Adjust the warmth of the air with the temperature control dial. To Heat and Dehumidify with Air Conditioning Air conditioning, as it cools, removes moisture from the air. When used in combination with the heater, it makes the interior warm and dry. 1. Switch the fan on. 2. Turn on the air conditioning. 3. Select and Fresh Air mode. 4.
Main Menu Table of Contents Heating and Cooling To remove exterior frost or ice from the windshield and side windows after the car has been sitting out in cold weather: MODE CONTROL DIAL 1. Start the engine. 2. Select When you select the system automatically switches to Fresh Air mode and turns on the A/C. 3. Switch the fan and temperature controls to maximum. To rapidly remove exterior frost or ice from the windshield (on very cold days), first select the Recirculation mode.
Main Menu Table of Contents Heating and Cooling These settings direct all the air flow to the defroster vents at the base of the windshield and the side window defroster vents. The air flow will get warmer and clear the windows faster as the engine warms up. You can close the side vents with the dial beside each vent. This will send more warm air to the windshield defroster vents. For safety, make sure you have a clear view through all the windows before driving away.
Main Menu Table of Contents Audio System On DX and HX models in the U.S., and the DX model in Canada A M / FM Stereo Audio System Your Honda's audio system provides clear reception on both AM and FM bands, while the preset buttons allow you to easily select your favorite stations. Operating the Radio The ignition switch must be in ACCESSORY (I) or ON (ID to operate the audio system. Turn the system on by pressing the PWR/ VOL knob or the A M / FM button. Adjust the volume by turning the knob.
Main Menu Table of Contents Audio System To store a frequency: 1. Select the desired band, AM or FM. FM1 and FM2 let you store two frequencies with each Preset button. 2. Use the TUNE or SEEK function to tune the radio to a desired station. U.S.: DX and HX models Canada: DX model PWR/VOL KNOB STEREO INDICATOR TUNE/SEEK BAR PRESET BUTTONS AM/FM BUTTON 3. Pick the Preset button you want for that station. Press the button and hold it until you hear a beep. 4.
Main Menu Table of Contents Audio System Adjusting the Sound Bass, Treble, Balance, and Fader are each adjustable. You select which of these you want to adjust by pressing the MODE button. The mode changes from BAS to TRE to FAD to BAL, and then back to VOL each time you press the button. Each mode is shown in the display as it changes. Balance/Fader — These two modes adjust the strength of the sound coming from each speaker.
Main Menu Table of Contents Audio System Digital Clock The audio system also displays the time. The ignition switch must be in ACCESSORY (I) or ON (II). TIME DISPLAYED To set the time, press the CLOCK button. The hour numbers will begin blinking. Press the Preset 5 button to get the numbers to count down, or the Preset 6 button to get the hours to count up. Press the CLOCK button again, and the minutes numbers will begin blinking.
Main Menu Table of Contents Audio System Operating the Optional CD Player/Changer A Compact Disc changer is available through your dealer. It holds up to six discs, providing several hours of continuous entertainment. You operate the CD changer with the same controls used for the radio. Your dealer also has an accessory indash single CD player available that is operated by the radio controls. To operate this unit, use the instructions (except for those relating to multiple discs) in this section.
Main Menu Table of Contents Audio System Press the EJECT button to remove the disc from the player. If you eject the disc, but do not remove it from the slot, the system will automatically reload the disc after 15 seconds and put the CD player in pause mode. To begin playing the disc, press the CD button. To select a different disc, press the appropriate preset button (1 — 6).
Main Menu Table of Contents Audio System CD Changer Error Indications If you see an error indication in the display while operating the CD changer, find the cause in the chart to the right. If you cannot clear the error indication, take the vehicle to your Honda dealer.
Main Menu Table of Contents Audio System A M / F M / CD Audio System On EX and Si models in the U.S., Si and SiR models in Canada Your Honda's audio system provides clear reception on both AM and FM bands, while the preset buttons allow you to easily select your favorite stations. The anti-theft feature will disable the system if it is disconnected from the car's battery. To get the system working again, you must enter a code number (see page 119 ).
Main Menu Table of Contents Audio System Operating the Radio The ignition switch must be in ACCESSORY (I) or ON (II) to operate the audio system. Turn the system on by pushing the PWR/ VOL knob. Adjust the volume by turning the same knob. PWR/VOL KNOB TUNE BAR AM/FM BUTTON SEEK BAR The band and frequency that the radio was last tuned to is displayed. To change bands, press the A M / FM button. On the FM band, ST will be displayed if the station is broadcasting in stereo.
Main Menu Table of Contents Audio System T U NE — Use the TUNE bar to tune the radio to a desired frequency. Press the side of the bar to tune to a higher frequency, and the side to tune to a lower frequency. The frequency numbers will start to change rapidly. Release the bar when the display reaches the desired frequency. To change the frequency in small increments, press and release the TUNE bar quickly. SEEK — The SEEK function searches the band for a station with a strong signal.
Main Menu Table of Contents Audio System AUTO SELECT — If you are traveling far from home and can no longer receive the stations you preset, you can use the Auto Select feature to find stations in the local area. To activate Auto Select, press the A. SEL button. A. SEL will flash in the display, and the system will go into scan mode for several seconds.
Main Menu Table of Contents Audio System Adjusting the Sound Balance/Fader — These two controls adjust the strength of the sound coming from each speaker. The Balance control adjusts the sideto-side strength, while the Fader control adjusts the front-to-back strength. To adjust the fader, push on the BASS/FADER control knob to get it to pop out. Pull it out slightly farther, and adjust the front-to-back sound to your liking.
Main Menu Table of Contents Audio System Audio System Lighting You can use the instrument panel brightness control dial to adjust the illumination of the audio system (see page 62). The audio system illuminates when the parking lights are on, even if the radio is turned off. Digital Clock The display of your audio system usually shows the time when the ignition switch is in ACCESSORY (I) or ON (II).
Main Menu Table of Contents Audio System Operating the CD Player You operate the CD player with the same controls used for the radio. With the ignition switch in ACCESSORY (I) or ON (II), insert the disc into the CD slot. Push the disc in halfway, the drive will pull it in the rest of the way and begin to play. The number of the track that is playing is shown in the display. CD SLOT AM/FM BUTTON TUNE BAR EJECT BUTTON You can also play 3-inch (8-cm) discs without using an adapter ring.
Main Menu Table of Contents Audio System If you turn the system off while a CD is playing, either with the PWR/VOL knob or by turning off the ignition, the disc will stay in the drive. When you turn the system back on, the CD will begin playing where it left off. Press the eject button to remove the disc from the drive. If you eject the disc, but do not remove it from the slot, the system will automatically reload the disc after 15 seconds and put the CD player in pause mode.
Main Menu Table of Contents Audio System Operating the CD Changer (Optional) A Compact Disc changer is available for your vehicle. It holds up to six discs, providing several hours of continuous entertainment. You operate this CD changer with the same controls used for the in-dash CD player. Load the desired CDs in the magazine and load the magazine in the changer according to the instructions that came with the unit. Play only standard round discs.
Main Menu Table of Contents Audio System Protecting Compact Discs Handle a CD by its edges; never touch either surface. Contamination from fingerprints, liquids, felt-tip pens, and labels can cause the CD to not play properly, or possibly jam in the drive. When a CD is not being played, store it in its case to protect it from dust and other contamination. To prevent warpage, keep CDs out of direct sunlight and extreme heat. To clean a disc, use a clean soft cloth.
Main Menu Table of Contents Audio System CD Player Error Indications If you see an error indication in the display while operating the CD player, find the cause in the chart to the right. If you cannot clear the error indication, take the car to your Honda dealer.
Main Menu Table of Contents Audio System CD Changer Error Indications If you see an error indication in the display while operating the CD changer, find the cause in the chart to the right. If you cannot clear the error indication, take the car to your Honda dealer.
Main Menu Table of Contents Audio System Operating the Cassette Player (Optional) The cassette system features Dolby B* noise reduction, automatic sensing of chromium-dioxide (CrO2) tape, and autoreverse for continuous play. TUNE BAR CD BUTTON PWR/VOL KNOB AM/FM BUTTON SEEK/SKIP BAR TAPE DIRECTION INDICATOR Make sure the tape opening on the cassette is facing to the right, then insert the cassette most of the way into the slot. The system will pull it in the rest of the way, and begin to play.
Main Menu Table of Contents Audio System The tape direction indicator will light to show you which side of the cassette is playing. The indicates the side you inserted facing upward is now playing. If you want to play the other side, press the PROG button. Dolby B noise reduction turns on when you insert a cassette. If the tape was not recorded with Dolby B noise reduction, turn it off by pressing the NR button. Dolby remains off until you turn it on by pressing the button again.
Main Menu Table of Contents Audio System SKIP — The skip function allows you to find the beginning of a song or passage. To activate SKIP, press the SEEK/SKIP bar. Press the side to advance to the beginning of the next song or passage, or the side to return to the beginning of the current song or passage. FF or REW will flash in the display as the tape moves. When the system reaches the beginning of the next song or passage (FF), or the beginning of the current one (REW), it goes back to PLAY mode.
Main Menu Table of Contents Audio System Caring for the Cassette Player The cassette player picks up dirt and oxides from the tape. This contamination builds up over time and causes the sound quality to degrade. To prevent this, you should clean the player after every 30 hours of use. Your dealer has a cleaning kit available. Look at the cassette before you insert it. If the tape is loose, tighten it by turning a hub with a pencil or your finger.
Main Menu Table of Contents Audio System Theft Protection On EX and Si models in the U.S., and Si and SiR models in Canada Your car's audio system will disable itself if it is disconnected from electrical power for any reason. To make it work again, the user must enter a specific five-digit code in the Preset buttons. Because there are hundreds of number combinations possible from five digits, making the system work without knowing the exact code is nearly impossible.
Main Menu Table of Contents Audio System Radio Frequencies Your Honda's radio can receive the complete AM and FM bands. Those bands cover these frequencies: AM band: 530 to 1,710 kilohertz FM band: 87.7 to 107.9 megahertz Radio stations on the AM band are assigned frequencies at least ten kilohertz apart (530, 540, 550). Stations on the FM band are assigned frequencies at least 0.2 megahertz apart (87.9, 88.1, 88.3). Stations must use these exact frequencies.
Main Menu Table of Contents Audio System Electrical interference from passing vehicles and stationary sources can cause temporary reception problems. As required by the FCC: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Radio signals, especially on the FM band, are deflected by large objects such as buildings and hills.
Main Menu 122
Main Menu Before Driving Before you begin driving your Honda, you should know what gasoline to use, and how to check the levels of important fluids. You also need to know how to properly store luggage or packages. The information in this section will help you. If you plan to add any accessories to your car, please read the information in this section first. Break-in Period.............................. 124 Gasoline......................................... . 124 Service Station Procedures..........
Main Menu Table of Contents Break-in Period, Gasoline Break-in Period Help assure your car's future reliability and performance by paying extra attention to how you drive during the first 600 miles (1,000 km). During this period: Avoid full-throttle starts and rapid acceleration. Avoid hard braking. New brakes need to be broken-in by moderate use for the first 200 miles (300 km). You should follow these same recommendations with an overhauled or exchanged engine, or when the brakes are relined.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Service Station Procedures Filling the Fuel Tank Pull Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. Stop the engine and keep heat, sparks, and flame away. Handle fuel only outdoors. Wipe up spills immediately. 1. Because the fuel fill cap is on the driver's side of the car, park with that side closest to the service station pumps. 2.
Main Menu Table of Contents Service Station Procedures Opening the Hood LATCH HOOD RELEASE HANDLE 1. Shift to Park or Neutral and set the parking brake. Pull the hood release handle located under the lower left corner of the dashboard. The hood will pop up slightly. Before Driving 2. Standing in front of the car, put your fingers under the front edge of the hood to the right of center. Slide your hand to the left until you feel the hood latch handle.
Main Menu Table of Contents Service Station Procedures Oil Check SUPPORT ROD DIPSTICK CLIP 3. Pull the support rod out of its clip and insert the end into the hole on the left side of the hood. To close the hood, lower it to about a foot (30 cm) above the fender, then press down firmly with your hands. After closing the hood, make sure it is securely latched. After closing the hood, make sure it is securely latched. Check the engine oil level every time you fill the car with fuel.
Main Menu Table of Contents Service Station Procedures Engine Coolant Check RESERVE TANK UPPER MARK LOWER MARK 3. Insert it all the way back in its tube. 4. Remove the dipstick again and check the level. It should be between the upper and lower marks. If it is near or below the lower mark, see Adding Oil on page 171. M AX M IN Look at the coolant level in the radiator reserve tank. Make sure it is between the MAX and M IN lines.
Main Menu Table of Contents Fuel Economy The condition of your car and your driving habits are the two most important things that affect the fuel mileage you get. Vehicle Condition Always maintain your car according to the maintenance schedule. This will keep it in top operating condition. An important part of that maintenance is the Owner Maintenance Checks (see page 169). For example, an underinflated tire causes more "rolling resistance," which uses fuel.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Accessories and Modifications Modifying your car, or installing some non-Honda accessories, can make your car unsafe. Before you make any modifications or add any accessories, be sure to read the following information. Accessories Your dealer has Genuine Honda accessories that allow you to personalize your car. These accessories have been designed and approved for your car, and are covered by warranty.
Main Menu Table of Contents Accessories and Modifications Modifications Do not remove any original equipment or modify your car in any way that would alter its design or operation. This could make your car unsafe and illegal to drive. In addition, any modifications that decrease ground clearance increase the chance of undercarriage parts striking a curb, speed bump, or other raised object, which could cause your airbags to deploy.
Main Menu Table of Contents Carrying Cargo CONSOLE COMPARTMENT FRONT DOOR POCKET Your car has several convenient storage areas so you can stow cargo safely. The glove box, and the pockets in the front doors and seat-backs, are designed for small, lightweight items. The trunk is intended for larger, heavier items. In addition, the back seat can be folded down to allow you to carry more cargo or longer items.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Carrying Cargo Load Limit The maximum load for your car is 850 lbs (395 kg). This figure includes the total weight of all occupants, cargo, and accessories. To figure out how much cargo you can carry: Add up the weight of all occupants. Subtract the total from 850 lbs (395 kg). The final number is the total weight of cargo you can carry.
Main Menu Table of Contents Carrying Cargo Carrying Cargo in the Trunk or on a Roof Rack Distribute cargo evenly on the floor of the trunk, placing the heaviest items on the bottom and as far forward as possible. If you fold down the back seat, tie down items that could be thrown about the car during a crash or sudden stop. If you carry large items that prevent you from closing the hatch, exhaust gas can enter the passenger area.
Main Menu Driving This section gives you tips on starting the engine under various conditions, and how to operate the 5-speed manual and automatic transmissions. It also includes important information on parking your car, and the braking system. Preparing to Drive......................... 136 Starting the Engine........................ 137 Starting in Cold Weather at High Altitude ..................... 137 5-speed Manual Transmission..... 138 Recommended Shift Points...... 139 Engine Speed Limiter .......
Main Menu Table of Contents Preparing to Drive You should do the following checks and adjustments every day before you drive your car. 1. Make sure all windows, mirrors, and outside lights are clean and unobstructed. Remove frost, snow, or ice. 2. Check that the hood and trunk are fully closed. 3. Visually check the tires. If a tire looks low, use a gauge to check its pressure. Driving 4. Check that any items you may be carrying with you inside are stored properly or fastened down securely. 5.
Main Menu Table of Contents Starting the Engine 1. Apply the parking brake. 2. In cold weather, turn off all electrical accessories to reduce the drain on the battery. 3. Manual Transmission: Push the clutch pedal down all the way. START (III) does not function unless the clutch pedal is depressed. Automatic Transmission (Including CVT): Make sure the shift lever is in Park. Press on the brake pedal. 4. Without touching the accelerator pedal, turn the ignition key to the START (III) position.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0 5-speed Manual Transmission Come to a full stop before you shift into Reverse. You can damage the transmission by trying to shift into Reverse with the vehicle moving. Push down the clutch pedal, and pause for a few seconds before shifting into Reverse, or shift into one of the forward gears for a moment. This stops the gears so they won't "grind." The manual transmission is synchronized in all forward gears for smooth operation.
Main Menu Table of Contents 5-speed Manual Transmission Recommended Shift Points Drive in the highest gear that lets the engine run and accelerate smoothly. This will give you the best fuel economy and effective emissions control. The following shift points are recommended: (U.S.: Si, Canada: SIR) run normally when you reduce the RPM below the red zone. Before downshifting, make sure the engine will not go into the tachometer's red zone. (U.S.
Main Menu Table of Contents Automatic Transmission Your Honda's transmission has four forward speeds, and is electronically controlled for smoother shifting. It also has a "lock-up" torque converter for better fuel economy. You may feel what seems like another shift when the converter locks. Driving On vehicles with ContinuouslyVariable Transmission(CVT): To operate your Honda's Continuously Variable Transmission (CVT), refer to the page 145 .
Main Menu Table of Contents Automatic Transmission Shift Lever Positions Shift Lever Position Indicator SHIFT LEVER This indicator on the instrument panel shows which position the shift lever is in. The "D4" indicator comes on for a few seconds when you turn the ignition switch ON (II). If it flashes while driving (in any shift position), it indicates a possible problem in the transmission. Avoid rapid acceleration and have the transmission checked by an authorized Honda dealer as soon as possible.
Main Menu Table of Contents Automatic Transmission If you have done all of the above and still cannot move the lever out of Park, see Shift Lock Release on page 144. You must also press the release button to shift into Park. To avoid transmission damage, come to a complete stop before shifting into Park. The shift lever must be in Park before you can remove the key from the ignition switch. Park (P) — This position mechanically locks the transmission.
Main Menu Table of Contents Automatic Transmission Reverse (R) — To shift to Reverse from Park, see the explanation under Park. To shift to Reverse from Neutral, come to a complete stop and then shift. Press the release button before shifting into Reverse from Neutral. Neutral (N) — Use Neutral if you need to restart a stalled engine, or if it is necessary to stop briefly with the engine idling. Shift to Park position if you need to leave the car for any reason.
Main Menu Table of Contents Automatic Transmission Engine Speed Limiter If you exceed the maximum speed for the gear you are in, the engine speed will enter into the tachometer's red zone. If this occurs, you may feel the engine cut in and out. This is caused by a limiter in the engine's computer controls. The engine will run normally when you reduce the RPM below the red zone.
Main Menu Table of Contents Automatic Transmission (CVT) RELEASE BUTTON Continuously Variable Transmission (CVT) On HX model Honda's Continuously Variable automatic transmission's unique design provides a smooth, constant flow of power. It is electronically controlled for more precise operation and better fuel economy. SHIFT LOCK RELEASE SLOT 4. Insert the key in the Shift Lock Release slot. 5.
Main Menu Table of Contents Automatic Transmission (CVT) Shift Lever Position Indicator Shift Lever Positions This indicator on the instrument panel shows which position the shift lever is in. The " D" indicator comes on for a few seconds when you turn the ignition switch ON (II). If it flashes while driving (in any shift position), it indicates a possible problem in the transmission. Avoid rapid acceleration and have the transmission checked by an authorized Honda dealer as soon as possible.
Main Menu Table of Contents Automatic Transmission (CVT) Park (P) — This position mechanically locks the transmission. Use Park whenever you are turning off or starting the engine. To shift out of Park, you must press on the brake pedal, have your foot off the accelerator pedal, and press the release button on the side of the shift lever. If you have done all of the above and still cannot move the lever out of Park, see Shift Lock Release on page 144.
Main Menu Table of Contents Automatic Transmission (CVT) Drive (D) — Use this position for your normal driving. The transmission automatically adjusts to keep the engine at the best speed for driving conditions. To help the engine warm up faster, the transmission will select ratios that allow the engine to run at higher speeds when it is cold. Second (S) — Selecting Second shifts the transmission into a lower range of ratios for better acceleration and increased engine braking.
Main Menu Table of Contents Parking Always use the parking brake when you park your car. The indicator on the instrument panel shows that the parking brake is not fully released; it does not indicate that the parking brake is firmly set. Make sure the parking brake is set firmly or your car may roll if it is parked on an incline. If the car is facing uphill, turn the front wheels away from the curb. If you have a manual transmission, put it in first gear.
Main Menu Table of Contents The Braking System On DX, HX and EX in the U.S., DX and EX models in Canada All Civics are equipped with front disc brakes. The brakes on the rear wheels are drum. A power assist helps reduce the effort needed on the brake pedal. Constant application of the brakes when going down a long hill builds up heat and reduces their effectiveness. Use the engine to assist the brakes by downshifting to a lower gear and taking your foot off the accelerator pedal.
Main Menu Table of Contents The Braking System Brake System Design The hydraulic system that operates the brakes has two separate circuits. Each circuit works diagonally across the vehicle (the left-front brake is connected with the right-rear brake, etc.). If one circuit should develop a problem, you will still have braking at two wheels. Front Anti-lock Brakes Standard on Si-R model in Canada. It is optional on the EX and Si models in the U.S., and DX and Si models in Canada.
Main Menu Table of Contents The Braking System You will feel a pulsation in the brake pedal when the ABS activates, and you may hear some noise. This is normal, it is the ABS rapidly pumping the brakes. Activation varies with the amount of traction your tires have. On dry pavement, you will need to press on the brake pedal very hard before you activate the ABS. However, you may feel the ABS activate immediately if you are trying to stop on snow or ice.
Main Menu Table of Contents The Braking System ABS Indicator ABS INDICATOR* *U.S. indicator shown The ABS is self-checking. If anything goes wrong, the ABS indicator on the instrument panel comes on (see page 55 ). This means the anti-lock function of the braking system has shut down. The brakes still work like a conventional system without antilock, providing normal stopping ability.
Main Menu Table of Contents Driving in Bad Weather Rain, fog, and snow conditions require a different driving technique because of reduced traction and visibility. Keep your car wellmaintained and exercise greater caution when you need to drive in bad weather. The cruise control should not be used in these conditions. Driving Driving Technique — Always drive slower than you would in dry weather. It takes your car longer to react, even in conditions that may seem just barely damp.
Main Menu Table of Contents Driving in Bad Weather, Towing a Trailer Towing a Trailer Your vehicle is not designed to tow a trailer. Attempting to do so can void your warranties. Traction — Check your tires frequently for wear and proper pressure. Both are important in preventing "hydroplaning" (loss of traction on a wet surface). In the winter, mount snow tires on all four wheels for the best handling. Watch road conditions carefully, they can change from moment to moment.
Main Menu 156
Main Menu Maintenance This section explains why it is important to keep your car well maintained and to follow basic maintenance safety precautions. This section also includes Maintenance Schedules for normal driving and severe driving conditions, a Maintenance Record, and instructions for simple maintenance tasks you may want to take care of yourself. If you have the skills and tools to perform more complex maintenance tasks on your Honda, you may want to purchase the Service Manual.
Main Menu Table of Contents Maintenance Safety Some of the most important safety Regularly maintaining your car is the This section includes instructions for precautions are given here. However, best way to protect your investment. simple maintenance tasks, such as we cannot warn you of every Proper maintenance is essential to checking 03/07/10 16:11:09 31S5A930 0021and adding oil.
Main Menu Table of Contents Maintenance Safety Important Safety Precautions Before you begin any maintenance, make sure your car is parked on level ground and that the parking brake is set. Also, be sure the engine is off. This will help to eliminate several potential hazards: Carbon monoxide poisoning from engine exhaust. Be sure there is adequate ventilation whenever you operate the engine. Burns from hot parts. Let the engine and exhaust system cool before touching any parts. Injury from moving parts.
Main Menu Table of Contents Maintenance Schedule The Maintenance Schedule specifies how often you should have your car serviced and what things need attention. It is essential that you have your car serviced as scheduled to retain its high level of safety, dependability, and emissions control performance. The services and time or distance intervals shown in the maintenance schedule assume you will use your car as normal transportation for passengers and their possessions.
Main Menu Table of Contents Maintenance Schedule Your authorized Honda dealer knows your car best and can provide competent, efficient service. However, service at a dealer is not mandatory to keep your warranties in effect. Maintenance may be done by any qualified service facility or person who is skilled in this type of automotive service. Keep all the receipts as proof of completion, and have the person who does the work fill out the Maintenance Record. Check your warranty booklet for more information.
Main Menu Table of Contents U.S. Owners Follow the Normal Conditions Maintenance Schedule if the severe driving conditions specified in the Severe Conditions Maintenance Schedule do not apply. NOTE: If you only OCCASIONALLYdrive under a "severe" condition, you should follow the Normal Conditions Maintenance Schedule. Canadian Owners Follow the Maintenance Schedule for Severe Conditions. * 1 : U.S.
Main Menu Table of Contents Service at the indicated distance or time, whichever comes first. Do the items in A, B, C as required for each distance/time interval. Follow this schedule if the severe driving conditions described in the Severe Conditions Schedule on the next page do not apply. Canadian owners:Follow the schedule for Severe Conditions. Page 198 Page 181 #: See Information on maintenance and emissions warranty, last column, page 161.
Main Menu Table of Contents U.S. Owners Follow the Severe Conditions Maintenance Schedule if you drive your vehicle MAINLY under one or more of the following conditions: Driving less than 5 miles (8 km) per trip or, in freezing temperatures, driving less than 10 miles (16 km) per trip. Driving in extremely hot [over 90°F (32° C] conditions. Extensive idling or long periods of stop-and-go driving. Driving with a roof-top carrier, or driving in mountainous conditions.
Main Menu Table of Contents Use this schedule if your vehicle is MAINLY driven in any of the following Severe Conditions, or normally driven in Canada; otherwise use the Normal Schedule. Service at the indicated distance or time, whichever comes first. Do the items in A, B, C as required for each distance/time.
Main Menu *1 Table of Contents : U.S.: Si model, Canada: SiR model Maintenance page 181.) #: See information on maintenance and emissions warranty, last column, page 161. : See Timing Belt on page 194 to determine need for replacement.
Main Menu Table of Contents Required Maintenance Record (for Normal and Severe Schedules) You or the servicing dealer can record all completed maintenance here, whether you follow the schedule for normal conditions (page 162 ) or severe conditions (page 164). Keep the receipts for all work done on your vehicle.
Main Menu Table of Contents Required Maintenance Record (for Normal and Severe Schedules) Maintenance
Main Menu Table of Contents Owner Maintenance Checks You should check the following items at the specified intervals. If you are unsure of how to perform any check, turn to the page given. Engine oil level — Check every time you fill the fuel tank. See page 127. Engine coolant level — Check the radiator reserve tank every time you fill the fuel tank. See page 128 . Windshield washer fluid — Check the level in the reservoir monthly.
Main Menu Table of Contents Fluid Locations BRAKE FLUID (Gray cap) CLUTCH FLUID (5-speed Manual Transmission only) (Gray cap) COOLANT RESERVOIR ENGINE OIL FILL CAP WASHER FLUID (Blue cap) AUTOMATIC TRANSMISSION FLUID DIPSTICK (Yellow loop) (Including CVT) POWER STEERING FLUID (Red cap) ENGINE OIL DIPSTICK (Orange loop) Maintenance
Main Menu Table of Contents Engine Oil Adding Oil ENGINE OIL FILL CAP Recommended Oil Oil is a major contributor to your engine's performance and longevity. Always use a premium-grade detergent oil. It is highly recommended that you use Genuine Honda Motor Oil in your vehicle for as long as you own it. The API Service label also tells you the service classification of the oil. Always use an oil that is labeled "API Service SJ." This service rating may include other classifications, such as CD.
Main Menu Table of Contents Engine Oil The oil container may also display the API Certification seal. Make sure it says "For Gasoline Engines." The SAE numbers tell you the oil's viscosity or weight. Select the oil for your car according to this chart. Ambient Temperature API CERTIFICATION MARK An oil with a viscosity of 5W-30 is preferred for improved fuel economy and year-round protection in your Honda. You may use a 10W-30 oil if the temperature in your area never goes below 20°F ( — 7°C).
Main Menu Table of Contents Engine Oil Changing the Oil and Filter Always change the oil and filter according to the time and distance (miles/kilometers) recommendations in the maintenance schedule. The oil and filter collect contaminants that can damage your engine if they are not removed regularly. Changing the oil and filter requires special tools and access from underneath the car. The car should be raised on a service station-type hydraulic lift for this service.
Main Menu Table of Contents Engine Oil 5. Put a new washer on the drain bolt, then reinstall the drain bolt. Tighten it to: (U.S.: DX and Si, Canada: DX and SiR) 33 lbf.ft (44 N.m, 4.5 kgf.m) (U.S.: HX, EX, Canada: Si) 29 lbf.ft (39 N.m, 4.0 kgf.m) 6. Refill the engine with the recommended oil. Engine oil change capacity (including filter): (U.S.: DX, Canada: DX) 3.8 US qt (3.6 ,3.2 Imp qt) (U.S.: HX, EX, Canada: Si) 3.5 US qt (3.3 ,2.9 Imp qt) (U.S.: Si, Canada: SiR) 4.2 US qt (4.0 , 3.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0 Cooling System Adding Engine Coolant RESERVE TANK If the coolant level in the reserve tank is at or below the MIN line, add coolant to bring it up to the MAX line. Inspect the cooling system for leaks. This coolant should always be a mixture of 50 percent antifreeze and 50 percent water. Never add straight antifreeze or plain water. Always use Genuine Honda Antifreeze/Coolant.
Main Menu Table of Contents Cooling System RADIATOR CAP 1. Make sure the engine and radiator are cool. 2. Turn the radiator cap counterclockwise, without pressing down on it, until it stops. This relieves any pressure remaining in the cooling system. 3. Remove the radiator cap by pushing down and turning counterclockwise. Maintenance RESERVE TANK 4. The coolant level should be up to the base of the filler neck. Add coolant if it is low. 5. Put the radiator cap back on. Tighten it fully. 6.
Main Menu Table of Contents Cooling System Replacing Engine Coolant The cooling system should be completely drained and refilled with new coolant according to the time and distance recommendations in the maintenance schedule. Only use Genuine Honda Antifreeze/Coolant. Draining the coolant requires access to the underside of the car. Unless you have the tools and knowledge, you should have this maintenance done by a skilled mechanic. DRAIN PLUG 1. Turn the ignition ON (II).
Main Menu Table of Contents Cooling System RESERVE TANK RESERVE TANK CAP HOLDER 4. Remove the reserve tank from its holder by pulling it straight up. Drain the coolant, then put the tank back in its holder. 5. When the coolant stops draining, tighten the drain plug at the bottom of the radiator. Maintenance (U.S.: Si model, Canada: SiR model) When the coolant stops draining, apply non-hardening sealant to the drain bolt threads, then reinstall the bolt and tighten it securely. 6.
Main Menu Table of Contents Cooling System 10.Install the radiator cap, and tighten it to the first stop. 11.Start the engine and let it run until the radiator fan comes on two times. Then stop the engine. 12.Remove the radiator cap. Fill the radiator with coolant up to the filler neck and the reserve tank up to the MAX mark. 13.Start the engine and hold it at 1,500 rpm until the cooling fan comes on. Turn off the engine. Check the coolant level in the radiator and add coolant if needed. 14.
Main Menu Table of Contents Windshield Washers, Transmission Fluid Windshield Washers Check the level in the windshield washer reservoir at least monthly during normal usage. In bad weather, when you use the washers often, check the level every time you stop for fuel. The windshield washer reservoir is located behind the driver's side headlight. Check the reservoir's fluid level by removing the cap and looking at the level gauge attached to the cap.
Main Menu Table of Contents Transmission Fluid DIPSTICK UPPER MARK LOWER MARK 2. Remove the dipstick (yellow loop) from the transmission and wipe it with a clean cloth. 3. Insert the dipstick all the way into the transmission securely as shown in the illustration. 5. If the level is below the lower mark, add fluid into the filler hole to bring it to the upper mark. Always use Honda Premium Formula Automatic Transmission Fluid (ATF).
Main Menu Table of Contents Transmission Fluid, Brake and Clutch Fluid 5-speed Manual Transmission FILLER BOLT Correct level Check the fluid level with the transmission at normal operating temperature and the car sitting on level ground. Remove the transmission filler bolt and carefully feel inside the bolt hole with your finger. The fluid level should be up to the edge of the bolt hole. If it is not, add Genuine Honda Manual Transmission Fluid (MTF) until it starts to run out of the hole.
Main Menu Table of Contents Brake and Clutch Fluid Always use Genuine Honda DOT 3 brake fluid. If it is not available, you should use only DOT 3 or DOT 4 fluid, from a sealed container, as a temporary replacement. However, the use of any non-Honda brake fluid can cause corrosion and decrease the life of the system. Have the brake system flushed and refilled with Honda DOT 3 brake fluid as soon as possible.
Main Menu Table of Contents Power Steering Check the level when the engine is cold. Look at the side of the reservoir. The fluid should be between the UPPER LEVEL and LOWER LEVEL. If it is below the LOWER LEVEL, add power steering fluid to the UPPER LEVEL. UPPER LEVEL A low power steering fluid level can indicate a leak in the system. Check the fluid level frequently and have the system inspected as soon as possible.
Main Menu Table of Contents Air Cleaner Element The air cleaner element should be replaced according to the time and distance recommendations in the maintenance schedule. Replacement CLIPS AIR CLEANER ELEMENT On DX model in the U.S., and DX model in Canada The air cleaner element is inside the air cleaner housing in the engine compartment. To replace it: 1. Unsnap the four clips and remove the air cleaner housing cover. 2. Remove the old air cleaner element. 3.
Main Menu Table of Contents Air Cleaner Element, Hood Latch Hood Latch Replacement AIR CLEANER ELEMENT PIVOTS CLIPS On HX, EX and Si models in the U.S., and Si and SiR models in Canada The air cleaner element is inside the air cleaner housing on the passenger's side of the engine compartment. To replace it: 1. Unsnap the two clips and remove the air cleaner housing cover. Maintenance 2. Remove the old air cleaner element. Carefully clean the inside of the air cleaner housing with a damp rag. 3.
Main Menu Table of Contents Spark Plugs The spark plugs in your car should be replaced according to the time and distance recommendations in the maintenance schedule. Replacement SPARK PLUG CAP 1. Clean up any dirt and oil around the spark plug caps. 2. Remove the spark plug cap by pulling it straight out. 4. Put the new spark plug into the socket; then screw it into the hole. Screw it in by hand so you do not crossthread it. 3. Remove the spark plug with a five-eighths inch (16 mm) spark plug socket.
Main Menu Table of Contents Spark Plugs NOTICE Tighten the spark plugs carefully. A spark plug that is too loose can overheat and damage the engine. Overtightening can cause damage to the threads in the cylinder head. 6. Install the spark plug cap. 7. Repeat this procedure for the other three spark plugs. 5. Torque the spark plug. (If you do not have a torque wrench, tighten the spark plug two-thirds of a turn after it contacts the cylinder head.) Tightening torque: 13 lbf.ft (18 N.m, 1.8 kgf.
Main Menu Table of Contents Battery Check the condition of your car's battery monthly. You should check the color of the test indicator window, and for corrosion on the terminals. TEST INDICATOR WINDOW Check the battery terminals for corrosion (a white or yellowish powder). To remove it, cover the terminals with a solution of baking soda and water. It will bubble up and turn brown. When this stops, wash it off with plain water. Dry off the battery with a cloth or paper towel.
Main Menu Table of Contents Battery 03/07/10 16:11:09 31S5A930 0021 If you need to connect the battery to a charger, disconnect both cables to prevent damage to the car's electrical system. The battery gives off explosive hydrogen gas during normal operation. If the terminals are severely corroded, clean them with baking soda and water. Then use a wrench to loosen and remove the cables from the terminals. Always disconnect the negative ( — ) cable first and reconnect it last.
Main Menu Table of Contents Wiper Blades Check the condition of the wiper blades at least every six months. Look for signs of cracking in the rubber, or areas that are getting hard. Replace the blades if you find these signs, or they leave streaks and unwiped areas when used. WIPER ARMS LOCK TAB To replace the blade: 1. Raise the wiper arm off the windshield. 2. Disconnect the blade assembly from the wiper arm by pushing in the lock tab.
Main Menu Table of Contents Wiper Blades BLADE BLADE 5. Slide the new wiper blade into the holder until the tabs lock. 6. Slide the wiper blade assembly onto the wiper arm. Make sure it locks in place. 7. Lower the wiper arm down against the windshield. REINFORCEMENT 3. Remove the blade from its holder by grasping the tabbed end of the blade. Pull firmly until the tabs come out of the holder. Maintenance 4. Examine the new wiper blades.
Main Menu Table of Contents Air Conditioning System Standard on EX and Si models in U.S., and SiR model in Canada Your car's air conditioning is a sealed system. Any major maintenance, such as recharging, should be done by a qualified mechanic. You can do a couple of things to make sure the air conditioning works efficiently. Periodically check the engine's radiator and air conditioning condenser for leaves, insects, and dirt stuck to the front surface.
Main Menu Table of Contents Drive Belts, Timing Belt Drive Belts POWER STEERING BELT ALTERNATOR BELT COMPRESSOR BELT Check the condition of the two or three drive belts. Examine the edges of each belt for cracks or fraying. Check the tension of each belt by pushing on it with your thumb midway between the pulleys. Maintenance The belts should have the following "play" or deflection. Alternator belt: (U.S.: DX, HX, EX, Canada: DX, EX) 0.31 — 0.41 in (8.0 — 10.5 mm) (U.S.: Si, Canada: SiR) 0.28 — 0.
Main Menu Table of Contents Tires To safely operate your car, your tires must be the proper type and size, in good condition with adequate tread, and correctly inflated. The following pages give more detailed information 03/07/10 16:11:09 31S5A930 on how and when to check air pressure, how to inspect your tires for damage and wear, and what to do when your tires need to be replaced.
Main Menu Table of Contents Tires If you check the pressure when the tires are hot (the car has been driven several miles), you will see readings 4 to 6 psi (30 to 40 kPa, 0.3 to 0.4 kgf/cm2 ) higher than the cold reading. This is normal. Do not let air out to match the specified cold pressure. The tire will be underinflated. Recommended Tire Pressures for Normal Driving The following chart shows the recommended cold tire pressures for most normal driving conditions and speeds. (U.S.
Main Menu Table of Contents Tires Inspection Every time you check inflation, you should also examine the tires for damage, foreign objects, and wear. You should look for: INDICATOR LOCATION MARKS Bumps or bulges in the tread or side of the tire. Replace the tire if you find either of these conditions. Cuts, splits, or cracks in the side of the tire. Replace the tire if you can see fabric or cord. Excessive tread wear. Be sure to readjust the pressure for normal driving speeds.
Main Menu Table of Contents Tires Maintenance In addition to proper inflation, correct wheel alignment helps to decrease tire wear. If you find a tire is worn unevenly, have your dealer check the wheel alignment. The tires were properly balanced by the factory. They may need to be rebalanced at some time before they are worn out. Have your dealer check the tires if you feel a consistent vibration while driving. A tire should always be rebalanced if it is removed from the wheel for repair.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 Tires When shopping for replacement tires, you may find that some tires are "directional." This means they are designed to rotate only in one direction. If you use directional tires, they should be rotated only front-toback. Replacing Tires and Wheels The tires that came with your car were selected to match the performance capabilities of the car while providing the best combination of handling, ride comfort, and long life.
Main Menu Table of Contents Tires The ABS works by comparing the speed of the wheels. When replacing tires, use the same size originally supplied with the car. Tire size and construction can affect wheel speed and may cause the system to work inconsistently. If you ever need to replace a wheel, make sure the wheel's specifications match those of the original wheel that came on your car. Replacement wheels are available at your Honda dealer. Wheels and Tires Wheels: (U.S.
Main Menu Table of Contents Tires Snow Tires If you mount snow tires on your Honda, make sure they are radial tires of the same size and load range as the original tires. Mount snow tires on all four wheels to balance your car's handling in all weather conditions. Keep in mind the traction provided by snow tires on dry roads may not be as high as your car's original equipment tires. You should drive cautiously even when the roads are clear. Check with the tire dealer for maximum speed recommendations.
Main Menu Table of Contents Lights Check the operation of your car's exterior lights at least once a month. A burned out bulb can create an unsafe condition by reducing your car's visibility and the ability to signal your intentions to other drivers.
Main Menu Table of Contents Lights STOP/TAILLIGHTS/ REAR SIDE MARKER LIGHTS STOP/TAILLIGHTS Check the following: Headlights (low and high beam) Parking lights Taillights Brake lights High-mount brake light Turn signals Back-up lights Hazard light function License plate light Side marker lights Daytime running lights (Canadian models) If you find any bulbs are burned out, replace them as soon as possible. Refer to the chart on page 248 to determine what type of replacement bulb is needed.
Main Menu Table of Contents Lights Replacing a Headlight Bulb Your car has halogen headlight bulbs, one on each side. When replacing a bulb, handle it by its steel base and protect the glass from contact with your skin or hard objects. If you touch the glass, clean it with denatured alcohol and a clean cloth. HOLDER NOTICE Halogen headlight bulbs get very hot when lit. Oil, perspiration, or a scratch on the glass can cause the bulb to overheat and shatter. Maintenance WEATHER SEAL CONNECTOR 1.
Main Menu Table of Contents Lights 4. Unclip the end of the hold-down wire from its slot. Pivot it out of the way and remove the bulb. 5. Insert the new bulb into the hole, making sure the tabs are in their slots. Pivot the hold-down wire back in place and clip the end into the slot. Replacing the Front Side Marker/ Turn Signal and Parking Light Bulb HOLDING CLIP 6. Install the rubber seal over the back of the headlight assembly. Make sure it is right side up; it is marked "TOP." 7.
Main Menu Table of Contents Lights 5. Remove the burned out bulb from the socket by pushing it in and turning counterclockwise until it unlocks. Replacing Rear Bulbs (in Fenders) 6. Install the new bulb in the socket. Turn it clockwise to lock it in place. 7. Insert the socket back into the headlight assembly. Turn it clockwise to lock it in place. 8. Test the lights to make sure the new bulb is working. 9. Put the inner fender cover in place. Install the holding clip and tighten it securely.
Main Menu Table of Contents Lights 4. Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms. 5. Reinstall the socket into the light assembly by turning it clockwise until it locks. 6. Test the lights to make sure the new bulb is working. 7. Reinstall the trunk lining. 8. Reset the fastener by pushing on the pointed end until it pops back almost flush with the fingers on the housing. 9.
Main Menu Table of Contents Lights 5. Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms. Replacing Rear Bulbs (in Trunk Lid) 6. Insert the socket back into the light assembly. Turn it clockwise to lock it in place. 7. Test the lights to make sure the new bulb is working. SCREW 1. Open the trunk. 2. Use a Phillips-head screwdriver to remove the two screws from the bulb holder. Remove the holder from the taillight assembly. Maintenance 3.
Main Menu Table of Contents Lights Replacing a Rear License Bulb Replacing a High-mount Brake Light Bulb 1. Open the trunk and remove the socket from the light assembly by turning it one-quarter turn counterclockwise. 2. Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms. 3. Reinstall the socket. Turn it clockwise until it locks. Make sure the new bulb is working. 1. Remove the two screws and remove the license light assembly. 2.
Main Menu Table of Contents Lights Replacing an Interior Light Bulb (U.S.: EX, Si, Canada: Si, SiR) INTERIOR LIGHT 4. Turn on the parking lights and check that the new bulb is working. 5. Reinstall the socket. Turn it clockwise until it locks. 6. Put the license light assembly in place. Reinstall the two screws and tighten them securely. Maintenance 1. Remove the lens by carefully prying on the edge of the lens in the middle with a fingernail file or a small flat-tip screwdriver.
Main Menu Table of Contents Lights (U.S.: EX and Si, Canada: Si and SiR) SPOTLIGHT Replacing the Trunk Light Bulb (U.S.: HX, EX and Si, Canada: DX, Si and SiR models) TRUNK LIGHT 2. Remove the bulb by pulling it straight out of its metal tabs. 3. Push the new bulb into the metal tabs. Snap the lens back in place. 1. Remove the lens by carefully prying on the edge of the lens in the middle with a fingernail file or a small flat-tip screwdriver. Do not pry on the edge of the housing around the lens.
Main Menu Table of Contents Storing Your Car If you need to park your car for an extended period (more than one month), there are several things you should do to prepare it for storage. Proper preparation helps prevent deterioration and makes it easier to get your car back on the road. If possible, store your car indoors. Fill the fuel tank. Change the engine oil and filter (see page 173). Wash and dry the exterior completely. Clean the interior. Make sure the carpeting, floor mats, etc.
Main Menu Appearance Care Regular cleaning and polishing of your Honda helps to keep it "new" looking. This section gives you hints on how to clean your car and preserve its appearance: the paint, brightwork, wheels and interior. Also included are several things you can do to help prevent corrosion. Exterior Care.................................. 214 Washing..................................... . 214 Waxing....................................... . 214 Aluminum Wheels.....................
Main Menu Exterior Care Washing Frequent washing helps preserve your car's beauty. Dirt and grit can scratch the paint, while tree sap and bird droppings can permanently ruin the finish. Wash your car in a shady area, not in direct sunlight. If the car is parked in the sun, move it into the shade and let the exterior cool down before you start. Only use the solvents and cleaners recommended in this Owner's Manual.
Main Menu Exterior Care Polishes — Polishes and cleaner/ waxes can restore the shine to paint that has oxidized and lost some of its shine. They normally contain mild abrasives and solvents that remove the top layer of the finish. You should use a polish on your Honda if the finish does not have its original shine after using a wax. Cleaning tar, insects, etc. with removers also takes off the wax. Remember to re-wax those areas, even if the rest of the car does not need waxing. Aluminum Wheels (U.S.
Main Menu Interior Care Carpeting Vacuum the carpeting frequently to remove dirt. Ground-in dirt will make the carpet wear out faster. Periodically shampoo the carpet to keep it looking new. Use one of the foam-type carpet cleaners on the market. Follow the instructions that come with the cleaner, applying it with a sponge or soft brush. Keep the carpeting as dry as possible by not adding water to the foam. Fabric Vacuum dirt and dust out of the material frequently.
Main Menu Interior Care, Corrosion Protection Windows Clean the windows, inside and out, with a commercially-available glass cleaner. You can also use a mixture of one part white vinegar to ten parts water. This will remove the haze that builds up on the inside of the windows. Use a soft cloth or paper towels to clean all glass and clear plastic surfaces. NOTICE The rear window defogger wires are bonded to the inside of the glass. Wiping vigorously up-and-down can dislodge and break the defogger wires.
Main Menu Corrosion Protection, Body Repairs Inspect and clean out the drain holes in the bottom of the doors and body. Check the floor coverings for dampness. Carpeting and floor mats may remain damp for a long time, especially in winter. This dampness can eventually cause the floor panels to corrode. Use a high-pressure spray to clean the underside of your car. This is especially important in areas that use road salt in winter. It is also a good idea in humid climates and areas subject to salt air.
Main Menu Taking Care of the Unexpected This section covers the morecommon problems that motorists experience with their vehicles. It gives you information about how to safely evaluate the problem and what to do to correct it. If the problem has stranded you on the side of the road, you may be able to get going again. If not, you will also find instructions on getting your car towed. Compact Spare Tire....................... 220 Changing a Flat Tire..................... 221 If Your Engine Won't Start.....
Main Menu Table of Contents Compact Spare Tire Your car has a compact spare tire that takes up less space. Use this spare tire as a temporary replacement only. Get your regular tire repaired or replaced and put back on your car as soon as you can. Check the inflation pressure of the compact spare tire every time you check the other tires. It should be inflated to: 60 psi (420 kPa , 4.
Main Menu Table of Contents Changing a Flat Tire If you have a flat tire while driving, SPARE TIRE stop in a safe place to change it. Stopping in traffic or on the shoulder 03/07/10 31S5A930 0021 of a busy16:11:09 road is dangerous. Drive slowly along the shoulder until you get to an exit or an area to stop that is far away from the traffic lanes. The car can easily roll off the jack, seriously injuring anyone underneath.
Main Menu Table of Contents Changing a Flat Tire JACK WHEEL WRENCH 6. Turn the jack's end bracket counterclockwise to loosen it, then remove the jack. Taking Care of the Unexpected 7. Loosen the four wheel nuts 1/2 turn with the wheel wrench. JACKING POINT 8. Locate the jacking point nearest the tire you need to change. It is pointed to by an arrow molded into the underside of the body. Place the jack under the jacking point.
Main Menu Table of Contents Changing a Flat Tire BRAKE HUB WHEEL WRENCH EXTENSION 9. Use the extension and wheel wrench as shown to raise the vehicle until the flat tire is off the ground. 10.Remove the wheel nuts and flat tire. Temporarily place the flat tire on the ground with the outside surface of the wheel facing up. You could scratch the wheel if you put it face down. On DX and EX models in the U.S.
Main Menu Table of Contents Changing a Flat Tire 12.Put on the spare tire. Put the wheel nuts back on finger-tight, then tighten them in a crisscross pattern with the wheel wrench until the wheel is firmly against the hub. Do not try to tighten them fully. Taking Care of the Unexpected 13.Lower the car to the ground and remove the jack. 14.Tighten the wheel nuts securely in the same crisscross pattern. Have the wheel nut torque checked at the nearest automotive service facility.
Main Menu Table of Contents Changing a Flat Tire 03/07/10 WING BOLT SPACER CONE 16:11:09 31S5A930 18.Store the jack in the trunk with the end bracket on the left side. Turn the jack's end bracket to lock it in place. Store the tool kit. 0021 Loose items can fly around the interior in a crash and could seriously injure the occupants. 15.Remove the wheel cover or center cap. Place the flat tire face down in the trunk well. 16.
Main Menu Table of Contents If Your Engine Won't Start Diagnosing why your engine won't start falls into two areas, depending on what you hear when you turn the key to START (III): You hear nothing, or almost nothing. The engine's starter motor does not operate at all, or operates very slowly. You can hear the starter motor operating normally, or the starter motor sounds like it is spinning faster than normal, but the engine does not start up and run.
Main Menu Table of Contents If Your Engine Won't Start, Jump Starting Jump Starting The Starter Operates Normally If your car's battery has run down, In this case, the starter motor's 03/07/10 31S5A930 you may16:11:09 be able to start the engine speed sounds normal, or even faster by using a booster battery. Although than normal, when you turn the this seems like a simple procedure, ignition switch to START (III), but you should take several precautions. the engine does not run.
Main Menu Table of Contents Jump Starting BOOSTER BATTERY 3. Connect one jumper cable to the positive ( + ) terminal on the booster battery. Connect the other end to the positive ( + ) terminal on your Honda's battery. 4. Connect the second jumper cable to the negative ( — ) terminal on the booster battery. Connect the other end to the grounding strap as shown. Do not connect this jumper cable to any other part of the engine. 5.
Main Menu Table of Contents If Your Engine Overheats The pointer of your car's tempera1. Safely pull to the side of the road. Your car can overheat for several ture gauge should stay in the midPut the transmission in Neutral or reasons, such as lack of coolant or a range under most conditions. It may Park and set the parking brake. mechanical problem. The only go higher if you are driving up a long Turn off the heating and cooling indication may be the temperature steep hill on a very hot day.
Main Menu Table of Contents If Your Engine Overheats 03/07/10 4. If the temperature gauge stays at the red mark, turn off the engine. 5. Wait until you see no more signs of steam or spray, then open the hood. 6. Look for any obvious coolant leaks, such as a split radiator hose. Everything is still extremely hot, so use caution. If you find a leak, it must be repaired before you continue driving (see Emergency Towing on page 241). 7.
Main Menu Table of Contents Low Oil Pressure Indicator LOW OIL PRESSURE INDICATOR NOTICE Running the engine with low oil pressure can cause serious mechanical damage almost immediately. Turn off the engine as soon as you can safely get the car stopped. 1. Safely pull off the road and shut off the engine. Turn on the hazard warning indicators. This indicator should light when the ignition switch is ON (II), and go out after the engine starts. It should never come on when the engine is running.
Main Menu Table of Contents Charging System Indicator CHARGING SYSTEM INDICATOR This indicator should come on when the ignition switch is ON (II), and go out after the engine starts. If it comes on brightly when the engine is running, it indicates that the charging system has stopped charging the battery. Taking Care of the Unexpected Immediately turn off all electrical accessories: radio, heater, A / C, rear defogger, cruise control, etc.
Main Menu Table of Contents Malfunction Indicator Lamp MALFUNCTION INDICATOR LAMP This indicator comes on for a few seconds when you turn the ignition switch ON (II). If it comes on at any other time, it indicates one of the engine's emissions control systems may have a problem. Even though you may feel no difference in your car's performance, it can reduce your fuel economy and cause your car to put out excessive emissions. Continued operation may cause serious damage.
Main Menu Table of Contents Brake System Indicator BRAKE SYSTEM INDICATOR* * U.S. indicator shown The Brake System indicator light should normally come on only when the parking brake is not fully released. If it comes on at any other time, it indicates a problem with the car's brake system. In most cases, the problem is a low fluid level in the brake fluid reservoir. Press lightly on the brake pedal to see if it feels normal.
Main Menu Table of Contents Closing the Moonroof If the electric motor will not close the moonroof, do the following: ROUND PLUG SOCKET 1. Check the fuse for the moonroof motor (see page 239). If the fuse is blown, replace it with one of the same or lower rating. 2. Try closing the moonroof. If the new fuse blows immediately or the moonroof motor still does not operate, you can close the moonroof manually. 3. Get the moonroof wrench out of the tool kit in the trunk. 4.
Main Menu Table of Contents Fuses All the electrical circuits in your car have fuses to protect them from a short circuit or overload. These fuses are located in three fuse boxes. INTERIOR The interior fuse box is underneath the dashboard on the driver's side. Remove the fuse box lid by swinging the lid down and pulling it straight out of its hinges. Taking Care of the Unexpected TAB UNDER-HOOD The under-hood fuse box is located in the engine compartment next to the battery.
Main Menu Table of Contents Fuses ABS FUSE BOX Vehicles equipped with ABS have a third fuse box for the ABS. It is in the engine compartment on the passenger's side. Checking and Replacing Fuses If something electrical in your car stops working, the first thing you should check for is a blown fuse. Determine from the chart on pages 239 and 240, or the diagram on the fuse box lid, which fuse or fuses control that component.
Main Menu Table of Contents Fuses FUSE PULLER BLOWN If you replace the blown fuse with a spare fuse that has a lower rating, it might blow out again. This does not indicate anything wrong. Replace the fuse with one of the correct rating as soon as you can. NOTICE 4. Check the smaller fuses in the under-hood fuse box and all the fuses in the interior fuse box by pulling out each fuse with the fuse puller provided in the interior fuse box. Taking Care of the Unexpected 5.
Main Menu Table of Contents Fuses INTERIOR FUSE BOX * : On Canadian models CONTINUED Taking Care of the Unexpected
Main Menu Table of Contents Fuses UNDER-HOOD FUSE BOX ABS FUSE BOX Taking Care of the Unexpected
Main Menu Table of Contents Emergency Towing If your car needs to be towed, call a professional towing service or, if you belong to one, an organization that provides roadside assistance. Never tow your car behind another vehicle with just a rope or chain. It is very dangerous. There are three popular types of professional towing equipment. Flat-bed Equipment — The operator loads your car on the back of a truck. This is the best way to transport your Honda.
Main Menu Table of Contents Emergency Towing With the front wheels on the ground, it is best to tow the car no farther than 50 miles (80 km), and keep the speed below 35 mph (55 km/h). If you decide to tow your car with all four wheels on the ground, make sure you use a properly-designed and attached tow bar. Prepare the car for towing as described above, and leave the ignition switch in Accessory (I) so the steering wheel does not lock.
Main Menu Technical Information The diagrams in this section give you the dimensions and capacities of your Honda, and the locations of the identification numbers. The explanations of several electronic and mechanical systems on your Honda are for the more technically-oriented owner. Identification Numbers................. 244 Specifications................................ . 246 DOT Tire Quality Grading (U.S. Cars).............................. 249 Treadwear.................................. 249 Traction.
Main Menu Table of Contents Identification Numbers Your car has several identifying numbers located in various places. The Vehicle Identification Number (VIN) is the 17-digit number your Honda dealer uses to register your car for warranty purposes. It is also necessary for licensing and insuring your car. The easiest place to find the VIN is on a plate fastened to the top of the dashboard. You can see it by looking through the windshield on the driver's side.
Main Menu Table of Contents Identification Numbers The Engine Number is stamped into the engine block. TRANSMISSION NUMBER The Transmission Number is on a label on top of the transmission.
Main Menu Table of Contents Specifications page 188 *1 : U.S.: DX, Canada: DX * 2 : U.S.: HX, EX, Canada: Si *3 : U.S.: DX, HX, Canada: DX * 4 : U.S.: EX, Canada: Si *5 : U.S.
Main Menu Table of Contents Specifications *1 : Including the coolant in the reserve tank and that remaining in the engine. Reserve tank capacity: 0.11 US gal (0.4 ,0.09 Imp gal) * 2 : Excluding the oil remaining in the engine. * 3 : U.S.: DX, Canada: DX *4 : U.S.: HX, EX, Canada: Si * 5 : U.S.:DX, Canada: DX * 6 : U.S.: HX, EX, Canada: Si *7 : U.S.: Si, Canada: SiR * 8 : Canadian Car * 9 : U.S.
Main Menu Table of Contents Specifications page 239 page 240 * 1 : U.S.: DX and HX without ABS, Canada: DX without ABS * 2 : U.S.: Cars equipped with CVT, EX without ABS, Canada: Si without ABS * 3 : U.S.: Cars equipped with ABS, Canada: Cars equipped with ABS * 4 : U.S.
Main Menu Table of Contents DOT Tire Quality Grading (U.S. Cars) The tires on your vehicle meet all U.S. Federal Safety Requirements. A ll tires are also graded for treadwear, traction, and temperature performance according to Department of Transportation (DOT) standards. The following explains these gradings. Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between the tread shoulder and the maximum section width.
Main Menu Table of Contents DOT Tire Quality Grading (U.S. Cars) Traction The traction grades, from highest to lowest, are A A, A, B, and C. Those grades represent the tire's ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.
Main Menu Table of Contents Oxygenated Fuels Some conventional gasolines are being blended with alcohol or an ether compound. These gasolines are collectively referred to as oxygenated fuels. To meet clean air standards, some areas of the United States and Canada use oxygenated fuels to help reduce emissions. The following are the U.S. EPA and Canadian CGSB approved percentages of oxygenates: ETHANOL (ethyl or grain alcohol) You may use gasoline containing up to 10 percent ethanol by volume.
Main Menu Table of Contents Driving in Foreign Countries If you are planning to take your Honda outside the U.S. or Canada, contact the tourist bureaus in the areas you will be traveling in to find out about the availability of unleaded gasoline with the proper octane rating. If unleaded gasoline is not available, be aware that using leaded gasoline in your Honda will affect performance and fuel mileage, and damage its emissions controls. It will no longer comply with U.S.
Main Menu Table of Contents Emissions Controls The burning of gasoline in your car's engine produces several byproducts. Some of these are carbon monoxide (CO), oxides of nitrogen (NOx) and hydrocarbons (HC). Gasoline evaporating from the tank also produces hydrocarbons. Controlling the production of NOx, CO, and HC is important to the environment. Under certain conditions of sunlight and climate, NOx and HC react to form photochemical "smog.
Main Menu Table of Contents Emissions Controls Exhaust Emissions Controls The exhaust emissions controls include three systems: PGM-FI, Ignition Timing Control and Three Way Catalytic Converter. These three systems work together to control the engine's combustion and minimize the amount of HC, CO, and NOx that comes out the tailpipe. The exhaust emissions control systems are separate from the crankcase and evaporative emissions control systems.
Main Menu Table of Contents Three Way Catalytic Converter The three way catalytic converter contains precious metals that serve as catalysts, promoting chemical reactions to convert the exhaust gasses without affecting the metals. The catalytic converter is referred to as a three-way catalyst, since it acts on HC, CO, and NOx. A replacement unit must be an original Honda part or its equivalent. The three way catalytic converter must operate at a high temperature for the chemical reactions to take place.
Main Menu 256
Main Menu Warranty and Customer Relations Customer Relations Information................................. 258 U.S. Zone Office Map.................... 259 Canada Zone Office Map.............. 260 Warranty Coverages..................... 261 Reporting Safety Defects (U.S. Vehicles)........................... 262 Authorized Manuals......................
Main Menu Table of Contents Customer Relations Information Honda dealership personnel are trained professionals. They should be able to answer all your questions. If you encounter a problem that your dealership does not solve to your satisfaction, please discuss it with the dealership's management. The Service Manager or General Manager can help. Almost all problems are solved in this way.
Main Menu Table of Contents U.S. Zone Office Map Mid-Atlantic Zone Western Zone P.O. Box 2260 902 Wind River Ln., Suite 200 700 Van Ness Avenue Gaithersburg, Maryland 20878 Torrance, California (301) 990-2020 90509-2260 Southeastern Zone (310)781-4565 1500 Morrison Parkway Northwestern Zone P.O. Box 20186 Alpharetta, Georgia 30004 (770) 442-2045 12439 N.E.
Main Menu Table of Contents Canada Zone Office Map CUSTOMER RELATIONS RELATIONS AVEC LA CLIENTELE Honda Canada Inc. 715 Milner Avenue Toronto, ON M1B 2K8 Tel: 1-888-9-HONDA-9 Fax: Toll-free 1-877-939-0909 Toronto (416) 287-4776 Honda Canada Inc.
Main Menu Table of Contents Warranty Coverages U.S. Owners Your new Honda is covered by these warranties: New Car Limited Warranty — covers your new vehicle, except for the battery, emissions control systems and accessories, against defects in materials and workmanship. Emissions Control Systems Defects Warranty and Emissions Performance Warranty — these two warranties cover your vehicle's emissions control systems. Time, mileage, and coverage are conditional.
Main Menu Table of Contents Reporting Safety Defects (U.S. Vehicles) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying American Honda Motor Co., Inc.
Main Menu Table of Contents Authorized Manuals Purchasing Factory Authorized Manuals (U.S. only) The following publications covering the operation and servicing of your vehicle can be obtained from Helm Incorporated, either by filling out the attached form or, for credit card holders, calling the toll-free phone number on the form. For manuals prior to the year shown below, contact Helm Incorporated, P.O. Box 07280, Detroit, Michigan 48207, or call 1-800-782-4356. Valid only for sales within the U.S.
Main Menu Table of Contents Authorized Manuals Service Manual: This manual covers maintenance and recommended procedures for repair to engine and chassis components. It is written for the Journeyman mechanic, but is simple enough for most mechanically-inclined owners to understand. Electrical Troubleshooting Manual: This manual complements the Service Manual by providing in-depth troubleshooting information for each electrical circuit in your vehicle.
Main Menu Index Accessories and Modifications.... 130 Accessories................................. 130 Additional Safety Precaution.... 131 Modifications............................. 131 ACCESSORY (Ignition Key Position)....................................... . 70 Accessory Power Socket................ 85 Adding Automatic Transmission Fluid........................................180 Brake Fluid................................. 183 Clutch Fluid................................ 183 Engine Coolant............
Main Menu Index Before Driving............................... 123 Belts, Seat........................................... 8 Beverage Holder.............................. 84 Body Repair.................................... 214 Brakes Anti-lock System (ABS)............ 151 Break-in, New Linings .............. 124 Fluid............................................ 182 Light, Burned-out...................... 206 Parking......................................... . 83 System Indicator..........................
Main Menu Index Consumer Information*................ 258 Controls, Instruments and.............. 51 Coolant Adding......................................... 175 Checking..................................... 128 Proper Solution.......................... 175 Replacing.................................... 177 Temperature Gauge.................... 58 Corrosion Protection..................... 217 Crankcase Emissions Control System.........................................253 Cruise Control Operation..............
Main Menu Index Engine Specifications............................. 246 Engine Speed Limiter....... 139, 144 Ethanol in Gasoline ....................... 251 Evaporative Emissions Controls.. 253 Exhaust Fumes................................ 49 Expectant Mothers, Use of Seat Belts by......................................... 19 Exterior, Cleaning the................... 214 Fabric, Cleaning............................. 216 Fan, Interior......................................
Main Menu Index Reminder Beeper......................... 61 Replacing Halogen Bulbs ......... 204 Turning on.................................... 61 Head Restraints............................... 77 Heating and Cooling........................ 88 High Altitude, Starting at.............. 137 High-Low Beam Switch .................. 61 High-mount Brake Light............... 209 Hood, Opening the ........................ 126 Horn.................................................. . 60 Hot Coolant, Warning about...
Main Menu Index Maintenance Record.................................. 167-168 Required Indicator....................... 59 Safety........................................... 158 Schedule.............................. 162-166 Malfunction Indicator Lamp.. 55, 233 Manual Transmission.................... 138 Manual Transmission Fluid ......... 182 Meters, Gauges................................ 57 Methanol in Gasoline.................... 251 Mirrors, Adjusting........................... 81 Moonroof...............
Main Menu Index Reclining the Seat Backs................ 76 Recommended Shift Speeds ........ 139 Reminder Lights.............................. 53 Remote Transmitter........................ 72 Replacement Information Air Cleaner Element.................. 185 Coolant....................................... . 177 Engine Oil and Filter................. 173 Fuses...........................................236 Light Bulbs................................. 202 Schedule.....................................
Main Menu Index SRS, Additional Information........... 45 Additional Safety Precautions.... 48 How Your Airbags Work............ 45 How Your SRS Indicator Works....................................... . 47 SRS Components.........................45 SRS Service................................... 47 SRS Indicator.............................. 47, 54 START (Ignition Key Position)..... 70 Starting the Engine........................ 137 In Cold Weather at High Altitude...................................
Main Menu Index Underside, Cleaning...................... 214 Unexpected, Taking Care of the........................................... 219 Uniform Tire Quality Grading..... 249 Unleaded Gasoline......................... 124 Upholstery Cleaning...................... 216 Used Oil, How to Dispose of........ 174 Vehicle Capacity Load .................. 132 Vehicle Dimensions....................... 246 Vehicle Identification Number..... 244 Vehicle Storage.............................. 212 Ventilation.......
Main Menu Service Information Summary Gasoline: U.S.: EX, DX, HX, Canada: DX and Si Unleaded gasoline, pump octane number of 86 or higher. U.S.: Si, Canada: SiR Premium unleaded gasoline, pump octane number of 91 or higher. Fuel Tank Capacity: 11.9 US gal (45 l,9.9 Imp gal) Recommended Engine Oil: API Service SJ "Energy Conserving" oil, SAE 5W-30 viscosity (see page 171 ). U.S.: DX, Canada: DX 3.8 US qt (3.6 l,3.2 Imp qt) U.S.: HX, EX, Canada: Si 3.5 US qt (3.3 l, 2.9 Imp qt) U.S.: Si, Canada: SiR 4.