2001 Accord Sedan Online Reference Owner's Manual Use these links (and links throughout this manual) to navigate through this reference. For a printed owner's manual, click on authorized manuals or go to www.helminc.com. Contents Owner's Identification Form Introduction ......................................................................................................................................... i A Few Words About Safety...........................................................................
Main Menu Owner's Identification OWNER This Owner's Manual should be considered a permanent part of the car, and should remain with the car when it is sold. ADDRESS STREET Main Menu CITY STATE/PROVINCE ZIP CODE / POSTAL CODE V. I. N. DELIVERY DATE (Date sold to original retail purchaser) DEALER NAME ADDRESS DEALER NO.
Main Menu Introduction Congratulations! Your selection of a 2001 Honda Accord was a wise investment. It will give you years of driving pleasure. One of the best ways to enhance the enjoyment of your new Honda is to read this manual. In it, you will learn how to operate its driving controls and convenience items. Afterwards, keep this owner's manual in your car so you can refer to it at any time. Several warranties protect your new Honda.
▼ ▲ Main Menu Main Menu A Few Words About Safety A Few Words About Safety Your safety, and the safety of others, Your safety, and the safety of others, is very important. And operating this is very important. operating this vehicle safely is anAnd important car safely is an important responsibility. responsibility.
Main Menu Your Car at a Glance MIRROR CONTROLS (P.100) DIGITAL CLOCK (P.102) DOOR LOCK SWITCH (P.75) HEATING/COOLING CONTROL (P.110) AUDIO SYSTEM (P.125) POWER WINDOW SWITCHES (P.97) TRUNK RELEASE HANDLE/ FUEL FILL DOOR (P.80, 178) HOOD RELEASE HANDLE (P.
Main Menu Your Car at a Glance INSTRUMENT PANEL BRIGHTNESS (P. 63) WINDSHIELD WIPERS/WASHERS (P. 64, 65, 66) REAR WINDOW DEFOGGER (P. 66) MOONROOF SWITCH (P. 98) TRACTION CONTROL SYSTEM (P. 206) CRUISE CONTROL (P. 68) HAZARD WARNING LIGHTS (P. 66) TILT ADJUSTMENT (P. 67) HEADLIGHTS/TURN SIGNALS (P. 62, 64) HORN (P. 61) REMOTE AUDIO CONTROLS (P. 70) (EX with leather and EX-V6 models) CRUISE CONTROLS (P.
Main Menu 44
Main Menu Driver and Passenger Safety This section gives you important information about how to protect yourself and your passengers. It shows you how to use seat belts properly. It explains your Supplemental Restraint System. And it tells you how to properly restrain infants and children in your car. Important Safety Precautions.......... 6 Your Car's Safety Features.............. 7 Seat Belts........................................ 8 Airbags............................................
Main Menu Table of Contents Important Safety Precautions You'll find many safety recommendations throughout this section, and throughout this manual. The recommendations on this page are the ones we consider to be the most important. Always Wear Your Seat Belt A seat belt is your best protection in all types of collisions. Airbags supplement seat belts, but airbags are designed to inflate only in a moderate to severe frontal collision.
Main Menu Table of Contents Your Car's Safety Features Your car is equipped with many features that work together to protect you and your passengers during a crash. Some safety features do not require any action on your part. These include a strong steel framework that forms a safety cage around the passenger compartment; front and rear crush zones that are designed to crumple and absorb energy during a crash; and a collapsible steering column.
Main Menu Table of Contents Your Car's Safety Features 03/07/10 16:11:09 Seat Belts For your safety, and the safety of your passengers, your car is equipped with seat belts in all seating positions. Your seat belt system also includes a light on the instrument panel to remind you and your passengers to fasten your seat belts. Why Wear Seat Belts Seat belts are the single most effective safety device for adults and larger children. (Infants and smaller children must be properly restrained in child seats.
Main Menu Table of Contents Your Car's Safety Features Airbags Airbags do not replace seat belts. They are designed to supplement the seat belts. Airbags offer no protection in rear impacts, rollovers, or minor frontal or side collisions. Airbags can pose serious hazards. Your car has a Supplemental Restraint System (SRS) with front airbags to help protect the heads and chests of the driver and a front seat passenger during a moderate to severe frontal collision.
Main Menu Table of Contents Your Car's Safety Features Seats & Seat-Backs Your car's seats are designed to keep you in a comfortable, upright position so you can take full advantage of the protection offered by seat belts and the energy absorbing materials in the seats. How you adjust your seats and seatbacks can also affect your safety.
Main Menu Table of Contents Your Car's Safety Features Pre-Drive Safety Checklist To make sure you and your passengers get the maximum protection from your car's safety features, check the following each time before you drive away: All adults, and children who have outgrown child safety seats, are wearing their seat belts and wearing them properly (see page 14). Any infant or small child is properly restrained in a child seat in the back seat (see page 19).
Main Menu Table of Contents Protecting Adults Introduction The following pages provide instructions on how to properly protect the driver and other adult occupants. These instructions also apply to children who have outgrown child seats and are large enough to wear lap/shoulder belts. (See page 34 for important additional guidelines on how to properly protect larger children.) 1. Close and Lock the Doors After everyone has entered the car, be sure the doors are closed and locked. 2.
Main Menu Table of Contents Protecting Adults Most shorter drivers can get far To reduce the chance of injury, wear enough away from the steering your seat belt properly, sit upright wheel and still reach the pedals. with your back against the seat, and However, if you are concerned about move the seat as far back as possible 03/07/10 31S5A930 0021 sitting too close, we recommend that from the16:11:09 steering wheel while still you investigate whether some type maintaining full control of the car.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 Protecting Adults Reclining a seat-back so that the 4.Adjust the Head Restraints shoulder part of the belt no longer rests against the occupant's chest reduces the protective capability of the belt. 16:11:09 It also increases 31S5A930 the chance 03/07/10 0021 of sliding under the belt in a crash and being seriously injured. The farther a seat-back is reclined, the greater the risk of injury.
Main Menu Table of Contents Protecting Adults 03/07/10 16:11:09 31S5A930 0021 spreads the forces of a crash over the strongest bones in your upper body. Improperly positioning the seat belts can cause serious injury or death in a crash. Position the lap part of the belt as low as possible across your hips, then pull up on the shoulder part of the belt so the lap part fits snugly. This lets your strong pelvic bones take the force of a crash and reduces the chance of internal injuries.
Main Menu Table of Contents Protecting Adults If a seat belt does not seem to work as it should, it may not protect the occupant in a crash. No one should sit in a seat with an inoperative seat belt. Anyone using a seat belt that is not working properly can be seriously injured or killed. Have your Honda dealer check the belt as soon as possible. See page 40 for additional information about your seat belt system and how to take care of your belts. 6.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Protecting Adults Advice for Pregnant Women Sitting improperly or out of position can result in serious injury or death in a crash. Always sit upright, well back in the seat, with your feet on the floor. Remember, to get the best protection from your car's airbags and other safety features, you must sit properly and wear your seat belt properly.
Main Menu Table of Contents Protecting Adults Additional Safety Precautions Two people should never use the same seat belt. If they do, they could be very seriously injured in a crash. Do not put any accessories on seat belts. Devices intended to improve occupant comfort or reposition the shoulder part of a seat belt can severely compromise the protective capability of the seat belt and increase the chance of serious injury in a crash.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Protecting Children Children who are unrestrained or improperly restrained can be seriously injured or killed in a crash. Any child too small for a seat belt should be properly restrained in a child seat. A larger child should be properly restrained with a seat belt. Children depend on adults to protect them. However, despite their best intentions, many parents and other adults may not know how to properly protect young passengers.
Main Menu Table of Contents Protecting Children Additional Precautions to Parents Never hold an infant or child on your lap. If you are not wearing a seat belt in a crash, you could be thrown forward into the dashboard and crush the child. If you are wearing a seat belt, the child can be torn from your arms during a crash. For example, if your car crashes into a parked vehicle at 30 mph (48 k m / h ) , a 20-lb (9 kg) infant will become a 600-lb (275 kg) force, and you will not be able to hold on.
Main Menu Table of Contents Protecting Children Small Children Placing a forward-facing child seat in the front seat of a vehicle equipped with a passenger's front airbag can be hazardous. If the vehicle seat is too far forward, or the child's head is thrown forward during a collision, an inflating front airbag can strike the child with enough force to kill or very seriously injure a small child. U.S.
Main Menu Table of Contents Protecting Children If You Must Drive with Several Children Your car has three seating positions in the back seat where children can be properly restrained. Canadian Models To remind you of the front airbag hazards, your car has warning labels on the driver's and front passenger's visors. Please read and follow the instructions on these labels.
Main Menu Table of Contents Protecting Children If a Child Requires Close Attention Many parents say they prefer to put an infant or small child in the front passenger seat so they can watch the child, or because the child requires attention. Placing a child in the front seat exposes the child to hazards from the passenger's front airbag, and paying close attention to a child distracts the driver from the important tasks of driving, placing both of you at risk.
Main Menu Table of Contents Protecting Children Lock all doors and the trunk when your car is not in use. Children who play in cars can accidentally get trapped inside the trunk. Teach your children not to play in or around cars. Know how to operate the emergency trunk opener (see page 81) and decide if your children should be shown how to use this feature. Keep car keys and remote transmitters out of the reach of children.
Main Menu Table of Contents Protecting Children Due to variations in the design of child seats, vehicle seats, and seat belts, all child seats will not fit all vehicle seating positions. Before purchasing a child seat, we recommend that parents test the child seat in the specific vehicle seating position (or positions) where they intend to use the seat. If a previously purchased child seat does not fit, you may need to buy a different one that will fit.
Main Menu Table of Contents Protecting Children Placing a Child Seat This page briefly summarizes Honda's recommendations on where to place rear-facing and forwardfacing child seats in your car. Airbags Pose Serious Risks to Children The passenger's front airbag inflates with enough force to kill or seriously injure an infant in a rear-facing child seat. A small child in a forward-facing child seat is also at risk.
Main Menu Table of Contents Protecting Children Installing a Child Seat 2. Make sure the child seat is firmly secured. After installing a child seat, push and pull the seat forward and from side to side to verify that it is secure. If the child seat is not secure, try installing it in a different seating position, or use a different style of child seat that can be firmly secured in the desired seating position. 1. Properly secure the child seat to the car.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Protecting Children Protecting Infants Rear-Facing Child Seat Placement Placing a rear-facing child seat in the front seat can result in serious injury or death if the passenger's front airbag inflates. Always place a rear-facing child seat in the back seat, not the front. Child Seat Type Only a rear-facing child seat provides proper support for a baby's head, neck, and back.
Main Menu Table of Contents Protecting Children When properly installed, a rearfacing child seat may prevent the driver or a front-seat passenger from moving the seat as far back as recommended (see page 12). Or it may prevent them from locking the seat-back in the desired upright position (see page 13). In either case, we recommend that you place the child seat directly behind the front passenger seat, move the front seat as far forward as needed, and leave it unoccupied.
Main Menu Table of Contents Protecting Children 2. To activate the lockable retractor, slowly pull the shoulder part of the belt all the way out until it stops, then let the belt feed back into the retractor (you might hear a clicking noise as the belt retracts). 3. After the belt has retracted, tug on it. If the belt is locked, you will not be able to pull it out. If you can pull the belt out, it is not locked and you will need to repeat these steps. Driver and Passenger Safety 4.
Main Menu Table of Contents Protecting Children Rear-Facing Child Seat Installation Tips Protecting Small Children We also recommend that a small child stay in the child seat as long as possible, until the child reaches the weight or height limit for the seat. Child Seat Placement In this car, the best place to install a forward-facing child seat is in one of the seating positions in the back seat. For proper protection, an infant must ride in a reclined, or semi-reclined position.
Main 16:11:09 Menu Table of31S5A930 Contents 03/07/10 0021 Protecting Children Child Seat Installation Improperly placing a forwardfacing child seat in the front seat can result in serious injury or death if the front airbags inflate. If you must place a forwardfacing child seat in front, move the vehicle seat as far back as possible and properly restrain the child.
Main Menu Table of Contents Protecting Children 2. To activate the lockable retractor, slowly pull the shoulder part of the belt all the way out until it stops, then let the belt feed back into the retractor (you might hear a clicking noise as the belt retracts). 3. After the belt has retracted, tug on it. If the belt is locked, you will not be able to pull it out. If you can pull the belt out, it is not locked and you will need to repeat these steps. 4.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Protecting Children Protecting Larger Children When a child reaches the recommended weight or height limit for a forward-facing child seat, the child should sit in the back seat and wear a lap/shoulder belt. If a child is too short for the shoulder part of the belt to properly fit, we recommend that the child use a booster seat until the child is tall enough to use the seat belt without a booster.
Main Menu Table of Contents Protecting Children However, if the belt touches or crosses the child's neck, the child needs to use a booster seat. Do not let a child wear a seat belt across the neck. This could result in serious neck injuries during a crash. Do not let a child put the shoulder part of a seat belt behind the back or under the arm. This could cause very serious injuries during a crash. It also increases the chance that the child will slide under the belt in a crash and be injured.
Main Menu Table of Contents Protecting Children A child may continue using a booster seat until the tops of the ears are even with the top of the seat-back. A child of this height should be tall enough to use the lap/shoulder belt without a booster. When Can a Larger Child Sit in Front Of course, children vary widely. And while age may be one indicator of when a child can safely ride in the front, there are other important factors you should consider.
Main Menu Table of Contents Protecting Children If you decide that a child can safely ride up front, be sure to: Carefully read the owner's manual and make sure you understand all seat belt instructions and all safety information. Supervise the child. Even mature children sometimes need to be reminded to fasten the seat belts or sit properly. Using Child Seats with Tethers Move the vehicle seat to the rearmost position.
Main Menu Table of Contents Protecting Children Using the Lower Anchorages LOWER ANCHORAGES Attach the tether strap hook to the tether anchorage point and tighten the strap according to the child seat maker's instructions. Your car is equipped with lower anchorages at the outer rear seats. These anchorages are located between the seat-back and seat bottom and are only to be used with a child seat designed to attach to the lower anchorages.
Main Menu Table of Contents Protecting Children Flexible type 3. Put the child seat in the rear left or right vehicle seat and attach the child seat to the lower anchorages according to the child seat maker's instructions. 4. Follow the child seat maker's instructions for any additional advice on adjusting or tightening the fit. 5. Attach the tether strap hook to the tether anchorage point and tighten the strap according to the child seat maker's instructions. 6.
Main Menu Table of Contents Additional Information About Your Seat Belts Seat Belt System Components Your seat belt system includes lap/ shoulder belts in all five seating positions. The seat belt system also includes a light on the instrument panel to remind you and your passengers to fasten your belts. If the driver's seat belt is not fastened before the ignition is turned ON (II), the light will come on and a beeper will also sound.
Main Menu Table of Contents Additional Information About Your Seat Belts If the shoulder part of the belt is pulled all the way out, the locking mechanism will activate. The belt will retract, but it will not allow the passenger to move freely. Automatic Seat Belt Tensioners To deactivate the locking mechanism, unlatch the buckle and let the seat belt fully retract. To refasten the belt, pull it out only as far as needed. See page 14 for instructions on how to wear the lap/shoulder belt properly.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Additional Information About Your Seat Belts Seat Belt Maintenance For safety, you should check the condition of your seat belts regularly. Pull each belt out fully and look for frays, cuts, burns, and wear. Check that the latches work smoothly and that the lap/shoulder belts retract easily. Any belt not in good condition or not working properly will not provide good protection and should be replaced as soon as possible. U.S.
Main Menu Table of Contents Additional Information About Your Airbags SRS Components Your Supplemental Restraint System (SRS) includes: Two front airbags. The driver's airbag is stored in the center of the steering wheel; the front passenger's airbag is stored in the dashboard. Both are marked "SRS AIRBAG." Automatic seat belt tensioners (see page 41) . Sensors that can detect a moderate to severe frontal collision.
Main Menu Table of Contents Additional Information About Your Airbags After a crash, you may see what looks like smoke. This is actually powder from the airbag's surface. Although the powder is not harmful, people with respiratory problems may experience some temporary discomfort. If this occurs, get out of the car as soon as it is safe to do so. During a frontal crash, your seat belts help restrain your lower body and torso.
Main Menu Table of Contents Additional Information About Your Airbags How Your Side Airbags Work Some models are equipped with side airbags for the driver and a front seat passenger. The airbags are stored in the outer edges of the front seat-backs, and both are marked "SIDE AIRBAG." Only one airbag will deploy during a side impact. If the impact is on the passenger's side, the passenger's side airbag will deploy even if there is no passenger.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Additional Information About Your Airbags If the light comes on at any other time, or does not come on at all, you should have the system checked by your dealer. For example: If the SRS indicator light does not come on after you turn the ignition ON (II). If the light stays on after the engine starts. If the light comes on or flashes on and off while you drive.
Main Menu Table of Contents Additional Information About Your Airbags If a small-statured adult leans sideways, or larger adult slouches and leans sideways into the deployment path of the side airbag, the system may also shut off the side airbag. If the side airbag indicator light comes on, you should have the passenger sit upright. Once the passenger is out of the deployment path of the side airbag, the system will turn the airbag back on and the light will go out.
Main Menu Table of Contents Additional Information About Your Airbags Airbag Service Your front and side airbag systems (if equipped) are virtually maintenance-free, and there are no parts you can safely service. However, you must have your car serviced if: Your airbags ever inflate. Any airbag that has deployed must be replaced along with the control unit and other related parts. Do not try to remove or replace any airbag by yourself. This must be done by a Honda dealer or a knowledgeable body shop.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Carbon Monoxide Hazard Your car's exhaust contains carbon monoxide gas. You should have no problem with carbon monoxide entering the car in normal driving if you maintain your car properly. Have the exhaust system inspected for leaks whenever: The car is raised for an oil change. You notice a change in the sound of the exhaust. The car was in an accident that may have damaged the underside. Carbon monoxide gas is toxic.
Main Menu Table of Contents Safety Labels These labels are in the locations shown. They warn you of potential hazards that could cause serious injury. Read these labels carefully. SUN VISOR U.S. models If a label comes off or becomes hard to read, contact your Honda dealer for a replacement. DASH BOARD U.S.
Main Menu Instruments and Controls This section gives information about the controls and displays that contribute to the daily operation of your Honda. All the essential controls are within easy reach. Control Locations............................ 52 Indicator Lights................................ 53 Gauges.............................................. 58 Speedometer................................ 58 Tachometer.................................. 58 Odometer......................................
Main Menu Table of Contents Control Locations MIRROR CONTROLS (P.100) DIGITAL CLOCK (P.102) DOOR LOCK SWITCH (P.75) AUDIO SYSTEM (P.125) POWER WINDOW SWITCHES (P.97) TRUNK RELEASE HANDLE/ FUEL FILL DOOR (P.80, 178) Instruments and Controls HEATING/COOLING CONTROL (P.110) HOOD RELEASE HANDLE (P.
Main Menu Table of Contents Indicator Lights TRACTION TRACTIONCONTROL CONTROL SYSTEM SYSTEMINDICATOR INDICATOR (P. (P.56) 56) CRUISE CRUISECONTROL CONTROL INDICATOR INDICATOR(P. (P.58) 58) SUPPLEMENTAL SUPPLEMENTAL RESTRAINT RESTRAINT SYSTEM SYSTEMINDICATOR INDICATOR(P. (P.55) 55) ANTI-LOCK ANTI-LOCKBRAKE BRAKESYSTEM SYSTEM INDICATOR* INDICATOR*(P. (P.55) 55) HIGH HIGHBEAM BEAMINDICATOR INDICATOR (P. (P.58) 58) PARKING PARKINGBRAKE BRAKEAND AND BRAKE BRAKESYSTEM SYSTEMINDICATOR* INDICATOR* (P. (P.
Main Menu Table of Contents Indicator Lights The instrument panel has many indicators to give you important information about your car. Seat Belt Reminder Light This indicator lights when you turn the ignition switch ON (II). It is a reminder to you and your passengers to protect yourselves by fastening the seat belts. A beeper also sounds if you have not fastened your seat belt. If you do not fasten your seat belt, the beeper will stop after a few seconds but the light stays on until you do.
Main Menu Table of Contents Indicator Lights U.S. Parking Brake and Brake System Indicator Canada 1. This indicator comes on when you turn the ignition switch ON (II). It is a reminder to check the parking brake. Driving with the parking brake not fully released can damage the brakes and tires. 2. If the indicator remains lit after you have fully released the parking brake while the engine is running, or if it comes on while driving, it can indicate a problem in the brake system.
Main Menu Table of Contents Indicator Lights TCS Traction Control System (TCS) Indicator Door and Brake Lamp Monitor On all V6 models This indicator has three functions: 1. It comes on as a reminder that you have turned off the Traction Control System. 2. It flashes when the TCS is regulating wheelspin. 3. If it comes on and stays on when the Traction Control System is on, it indicates that there is a problem in the TCS.
Main Menu Table of Contents Indicator Lights "Daytime Running Lights" Indicator Canadian models only This indicator lights when you turn the ignition switch to ON (II) with the headlight switch off and the parking brake set. It should go off if you turn on the headlights or release the parking brake. If it comes on at any other time, it means there is a problem with the DRL. There may also be a problem with the high beam headlights.
Main Menu Table of Contents Gauges TACHOMETER MAINTENANCE REQUIRED INDICATOR SPEEDOMETER TRIP METER Speedometer U.S. Models This shows your speed in miles per hour (mph). The smaller inner numbers are the speed in kilometers per hour (km/h). Canadian Models This shows your speed in kilometers per hour (km/h). The smaller inner numbers are the speed in miles per hour (mph).
Main Menu Table of Contents Gauges Trip Meter This meter shows the number of miles (U.S.) or kilometers (Canada) driven since you last reset it. There are two trip meters: Trip A and Trip B. Switch between these displays by pressing the Select/ Reset button repeatedly. Each trip meter works independently, so you can keep track of two different distances. To reset a trip meter, display it and then press and hold the Select/Reset button until the number resets to "0.0".
Main Menu Table of Contents Gauges Maintenance Required Indicator SELECT/RESET BUTTON Your dealer will reset this indicator after completing the scheduled maintenance. If this maintenance is done by someone other than your Honda dealer, reset the indicator as follows. 1. Turn off the engine. 2. Press and hold the select/reset button in the instrument panel, then turn the ignition switch ON (II).
Main Menu Table of Contents Controls Near the Steering Wheel The two levers on the steering column contain controls for driving features you use most often. The left lever controls the turn signals, headlights, and high beams. The right lever controls the windshield washers and wipers. INSTRUMENT PANEL BRIGHTNESS (P. 63) The controls under the left air vent are for the moonroof and the cruise control. MOONROOF SWITCH (P.
Main Menu Table of Contents Controls Near the Steering Wheel Headlights The rotating switch on the left lever controls the lights. Turning this switch to the position turns on the parking lights, taillights, instrument panel lights, side-marker lights, and rear license plate lights. Turning the switch to the position turns on the headlights.
Main Menu Table of Contents Controls Near the Steering Wheel Automatic Lighting Off Feature On EX and EX-V6 models The Automatic Lighting Off feature turns off the headlights, parking lights, taillights, side marker lights, license plate lights and instrument panel lights within 15 seconds of removing the key from the ignition switch and closing the driver's door. This feature activates if you leave the headlight switch in the or position, remove the key, open, then close the driver's door.
Main Menu Table of Contents Controls Near the Steering Wheel Turn Signals To signal a lane change, push lightly on the turn signal lever in the proper direction and hold it. The lever will return to the center position as soon as you release it. Windshield Wipers TURN SIGNAL LEVER Signal a turn or lane change with this lever. Push down on the lever to signal a left turn, and up to signal a right turn.
Main Menu Table of Contents Controls Near the Steering Wheel In intermittent, the wipers operate every few seconds. The sweep interval will change slightly with speed; getting shorter as you drive faster. In low speed and high speed, the wipers run continuously. On all models except DX You can vary how often the wipers sweep the windshield by turning the INT TIME ring next to the rotary switch. To operate the wipers in mist mode, push the control lever down.
Main Menu Table of Contents Controls Near the Steering Wheel Windshield Washers Hazard Warning Rear Window Defogger To clean the windshield, pull back on the wiper control lever. The washers spray until you release the lever. The wipers run at low speed while you're pulling the lever, then complete one more sweep of the windshield after you release it. Push the button to the left of the clock to turn on the hazard warning lights (four-way flashers).
Main Menu Table of Contents Controls Near the Steering Wheel Make sure the rear window is clear Steering Wheel Adjustment and you have good visibility before See page 16 for important safety 03/07/10 16:11:09 31S5A930 0021 starting to drive. information about how to properly position the steering wheel. Make any steering wheel adjustment The defogger and antenna wires on the inside of the rear window can be before you start driving. accidentally damaged. When cleaning the glass, always wipe side to side.
Main Menu Table of Contents Steering Wheel Controls Cruise Control Except for DX model in the U.S. Cruise control allows you to maintain a set speed above 25 mph (40 km/h) without keeping your foot on the accelerator pedal. It should be used for cruising on straight, open highways. It is not recommended for conditions such as city driving, 03/07/10 16:11:09 31S5A930 winding roads, slippery roads, heavy rain, or bad weather. You should have full control of the car under those conditions.
Main Menu Table of Contents Steering Wheel Controls The cruise control may not hold the set speed when you are going up and down hills. If your speed increases going down a hill, use the brakes to slow down to the desired speed. This will cancel the cruise control. To resume the set speed, press the RESUME/accel button. The CRUISE CONTROL light on the instrument panel comes on. When climbing a steep hill, the automatic transmission may downshift to hold the set speed.
Main Menu Table of Contents Steering Wheel Controls Cancelling the Cruise Control You can cancel the cruise control in any of these ways: Tap the brake or clutch pedal. Push the CANCEL button on the steering wheel. Press the Cruise Control Master Switch. When you push the CANCEL button, or tap the brake or clutch pedal, the CRUISE CONTROL light on the instrument panel will go out and the car will begin to slow down. You can use the accelerator pedal in the normal way.
Main Menu Table of Contents Keys and Locks Keys KEY NUMBER PLATE MASTER KEY (BLACK) VALET KEY (GREY) Your car comes with two master keys and a valet key. The master key fits all the locks on your car: Ignition Doors Trunk Glove box Trunk release handle Trunk pass-through cover Rear seat trunk access The valet key works only in the ignition and the door locks.
Main Menu Table of Contents Keys and Locks Immobilizer System The Immobilizer System protects your car from theft. A properlycoded master or valet key must be used in the ignition switch for the engine to start. If an improperlycoded key (or other device) is used, the engine's fuel system is disabled. When you turn the ignition switch to ON (II), the Immobilizer System indicator should come on for a few seconds, then go out.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Keys and Locks Ignition Switch The ignition switch is on the right side of the steering column. It has four positions: LOCK (0) ACCESSORY (I) ON (II) START (III) LOCK (0) — You can insert or remove the key only in this position. To switch from ACCESSORY to LOCK, you must push the key in slightly as you turn it. If your car has an automatic transmission, the shift lever must also be in Park.
Main Menu Table of Contents Keys and Locks ACCESSORY (I) — In this position, you can operate the audio system and the accessory power socket. ON (II) — This is the normal key position when driving. All features and accessories on the car are usable. Several of the lights on the instrument panel come on as a test when you turn the ignition switch from ACCESSORY to ON. START (III) — Use this position only to start the engine. The switch returns to ON (II) when you let go of the key.
Main Menu Table of Contents Keys and Locks To lock any passenger's door when getting out of the car, push the lock tab down and close the door. To lock the driver's door, pull the outside door handle and push the lock tab down. Release the handle, then close the door. Power Door Locks MASTER DOOR LOCK SWITCH The front doors can be locked and unlocked from the outside with the key. On all models except DX Each front door has a master door lock switch. Either switch locks and unlocks all doors.
Main Menu Table of Contents Keys and Locks Lockout Prevention If you forget and leave the key in the ignition switch, Lockout Prevention will not allow you to lock the driver's door. With the driver's door open and the key in the ignition, both master door lock switches are disabled. However, if the driver's door is not open, the master door lock switches are not disabled. Pushing the switch down on the open passenger's door will lock all doors.
Main Menu Table of Contents Keys and Locks You cannot lock or unlock the doors with the remote transmitter if any door is not fully closed or the key is in the ignition switch. If you unlock the doors with the remote transmitter, but do not open any of the doors within 20 seconds, the doors automatically relock and the security system sets. When you push the LOCK button a second time within 5 seconds after you have locked the doors, the horn will sound once to verify that the security system will be set.
Main Menu Table of Contents Keys and Locks Replacing the Battery BATTERY When the remote transmitter's battery begins to get weak, it may take several pushes on the button to lock or unlock the doors, and the LED will not light. Replace the battery as soon as possible. Battery type: CR2025 To replace the battery, pry the two parts of the transmitter apart. Instruments and Controls Remove the old battery and note the polarity.
Main Menu Table of Contents Keys and Locks As required by the FCC: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Main Menu Table of Contents Keys and Locks Trunk Childproof Door Locks LEVER TRUNK RELEASE HANDLE The childproof door locks are designed to prevent children seated in the rear from accidentally opening the rear doors. Each rear door has a lock lever near the edge. With the lever in the LOCK position, the door cannot be opened from the inside regardless of the position of the lock tab. To open the door, pull the lock tab up and use the outside door handle.
Main Menu Table of Contents Keys and Locks Emergency Trunk Opener MASTER KEY To open the trunk, push the release lever to the left. Parents should decide if their children should be shown how to use this feature. For more information about child safety, see page 19. To protect items in the trunk when you need to give the key to someone else: 1. Lock the trunk release handle with the master key. Also make sure the trunk pass-through cover is locked (see page 95).
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Keys and Locks Glove Box An open glove box can cause serious injury to your passenger in a crash, even if the passenger is wearing the seat belt. Always keep the glove box closed while driving. GLOVE BOX Open the glove box by squeezing the handle. Close it with a firm push. Lock or unlock the glove box with the master key. The glove box light comes on only when the instrument panel lights are on.
Main Menu Table of Contents HomeLink Universal Transmitter On all V6 models The HomeLink Universal Transmitter built into your car can be programmed to operate remotelycontrolled devices around your home, such as garage doors, lighting, or home security systems. It can replace up to three remote transmitters. Customer Assistance If you have problems with training the HomeLink Universal Transmitter, or would like information on home products that can be operated by the transmitter, call (800) 355-3515.
Main Menu Table of Contents HomeLink Universal Transmitter Training the Transmitter Before you can use the HomeLink Universal Transmitter to operate devices around your home, it must "learn" the proper codes. For example, to train the transmitter to open and close the garage door: Before you begin — If you just took delivery of your vehicle and have not trained any of the buttons in the HomeLink transmitter before, you should erase any previously learned codes before training the first button.
Main Menu Table of Contents HomeLink Universal Transmitter Canadian Owners: The remote control you are training from may stop transmitting after two seconds. This is not long enough for the HomeLink transmitter to learn the code. Release and press the button on the remote control every two seconds until the transmitter has learned the code. 5. The red light in the transmitter should begin flashing. It will flash slowly at first, then rapidly. 6. When the red light flashes rapidly, release both buttons.
Main Menu Table of Contents HomeLink Universal Transmitter It may be helpful to have someone assist you with this procedure. TRAINING BUTTON 1. Make sure you have properly completed the "Training the Transmitter" procedure. 2. Find the "Training" button on your garage door opener unit. The location will vary, depending on the manufacturer. The manufacturer's documentation may help. Instruments and Controls 3.
Main Menu Table of Contents HomeLink Universal Transmitter Retraining a Button To train an already programmed transmitter button to operate a new device: 1. Select the transmitter button you want to train. 2. Press and hold the transmitter button until the red light begins to flash slowly (approximately 20 seconds). 3. While continuing to hold the transmitter button, place the remote control for the device 2 to 5 inches from the HomeLink transmitter. 4. Press and hold the button on the remote control.
Main Menu Table of Contents Seat Adjustments All V-6 models, and the 4-cylinder EX model with leather interior have a power adjustable driver's seat. Front Seat Adjustments The EX-V6 model also has a power adjustable passenger's seat (See page 92 ). The 4-cylinder EX model without leather interior has a power seat bottom height adjustment. All other seat adjustments in this model are manual. The 4-cylinder DX, LX models have manual seat adjustments (see next column).
Main Menu Table of Contents Seat Adjustments Driver's Seat Manual Height Adjustment Driver's Seat Power Height Adjustment On LX model On EX model without leather The height of your driver's seat is power adjustable. Pull up on the switch to raise the seat. Push it down to lower the seat. The height of your driver's seat is adjustable. Turn the front dial on the outside of the seat cushion to raise the front of the seat bottom and turn the rear dial to raise the rear.
Main Menu Table of Contents Seat Adjustments Driver's Seat Full Power Adjustments On all V-6 models, and the 4-cylinder EX model with leather interior See pages 12 — 13 for important safety information and warnings about how to properly position seats and seat-backs. The two power seat adjustment switches are on the outside edge of the seat bottom. The horizontal switch adjusts the seat bottom in several directions. The short vertical switch adjusts the seat-back angle.
Main Menu Table of Contents Seat Adjustments Driver's Lumbar Support Pull the center of the horizontal switch up to raise the seat. Push it down to lower the seat. Adjust the seat-back angle by pushing the rear switch in the direction you want to move. On EX and EX V-6 models Vary the lumbar support by moving the lever on the right side of the seat-back. Pivot the lever forward until it stops, then let it return. Doing this several times adjusts the lumbar support through its full range.
Main Menu Table of Contents Seat Adjustments Front Passenger's Seat Adjustments Head Restraints The head restraints help protect you and your passengers from whiplash and other injuries. They are most effective when you adjust them so the back of the occupant's head rests against the center of the restraint. A taller person should adjust the restraint as high as possible. RELEASE BUTTON On EX-V6 model The seat adjustment switches are on the outside edge of the seat bottom.
Main Menu Table of Contents Seat Adjustments Folding Rear Seat MASTER KEY The back of the rear seat folds down, giving you direct access to the trunk. The seat-back can be released from inside the car or inside the trunk. To fold down the seat-back from inside the car, insert the master key in the lock on the rear shelf. Turn the key clockwise, pull down the top of the seat-back, then release the key.
Main Menu Table of Contents Seat Adjustments Make sure all rear shoulder belts are positioned in front of the rear seatback whenever the seat-back is in its upright position. Never drive with the seat-back folded down and the trunk lid open. See Carbon Monoxide Hazard on page 49. Rear Seat Armrest On all models except DX Make sure all items in the trunk, or items extending through the opening into the back seat, are secured. Loose items can fly forward and cause injury if you have to brake hard.
Main Menu Table of Contents Seat Adjustments Trunk Pass-through Cover KNOB For security, this cover can be locked and unlocked only with the master key. To lock the cover, insert the key and turn it clockwise. Never drive with this cover open and the trunk lid open. See Carbon Monoxide Hazard on page 49. LID The pass-through cover can be opened from either side; it folds forward onto the center armrest. Open the cover by sliding the knob downward and pushing or pulling on the cover.
Main Menu Table of Contents Seat Heaters The HI or LO indicator lights and remains lit until you turn it off by pushing the opposite side of the switch lightly. The indicator will turn off. In HI, the heater turns off when the seat gets warm, and turns back on after the seats temperature drops. It continues to cycle as long as you leave it set on HI. The HI indicator remains lit as a reminder that you have the heater on.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Power Windows On all models except DX Your car's windows are electricallypowered. Turn the ignition switch to ON (II) to raise or lower any window. Each door has a switch that controls its window. To open the window, push the switch down and hold it. Release the switch when you want the window to stop. Close the window by pushing the switch up and holding it. Closing a power window on someone's hands or fingers can cause serious injury.
Main Menu Table of Contents Power Windows, Moonroof The master control panel also contains these extra features: AUTO — To open the driver's window fully, push the window switch firmly down and release it. The window automatically goes all the way down. To stop the window from going all the way down, pull back on the window switch briefly. To open the driver's window only partially, push the window switch down lightly and hold it. The window will stop as soon as you release the switch.
Main Menu Table of Contents Moonroof, Mirrors To tilt up the back of the moonroof, The moonroof has a key-off delay. press and hold the center button You can still open and close the ( ). To close the moonroof, moonroof for up to ten minutes after press and hold the top of the switch you turn off the ignition. The key-off ( ). To open the moonroof, delay cancels as soon as you open press and hold the bottom of the either front door. You must then switch ( ).
Main Menu Table of Contents Mirrors Adjusting the Power Mirrors SELECTOR SWITCH 1. Turn the ignition switch ON (II). 2. Move the selector switch to L (driver's side) or R (passenger's side). ADJUSTMENT SWITCH On all models except DX Adjust the outside mirrors with the adjustment switch on the driver's door armrest: Instruments and Controls 3. Push the appropriate edge of the adjustment switch to move the mirror right, left, up or down. 4.
Main Menu Table of Contents Mirrors, Parking Brake Parking Brake HEATED MIRROR BUTTON NOTICE Driving the car with the parking brake applied can damage the rear brakes and axles. PARKING BRAKE LEVER On all Canadian models except DX model The outside mirrors are heated to remove fog and frost. With the ignition switch ON (II), turn on the heaters by pressing the button. The light in the button comes on as a reminder. Press the button again to turn the heaters off.
Main Menu Table of Contents Digital Clock H M R You can use R to quickly set the time to the nearest hour. If the displayed time is before the half hour, pressing R sets the clock back to the previous hour. If the displayed time is after the half hour, pressing R sets the clock forward to the beginning of the next hour. For example: 1:06 would RESET to 1:00. 1:52 would RESET to 2:00. The digital clock displays the time with the ignition switch in any position. To set the clock: 1.
Main Menu Table of Contents Console Compartment, Coin Box Console Compartment LEVER Coin Box LEVER CONSOLE COMPARTMENT To open the console compartment, pull up on the lower lever and lift the lid. To close, lower the lid and push it down until it latches. COIN BOX You can put small items in the tray located in the console compartment lid. To use the tray, pull up on the upper lever and lift up the armrest pad. The coin box is located under the airvent. To open the coin box, pull the bottom edge.
Main Menu Table of Contents Beverage Holder Push To open the beverage holder, push on the top. The beverage holder lid is spring-loaded and will swing open. To close it, push it down until it latches. Instruments and Controls The inner liner can be removed if you want to hold a larger cup. Be careful when you are using the beverage holder. A spilled liquid that is very hot can scald you or your passengers.
Main Menu Table of Contents Sun Visor, Vanity Mirror Sun Visor To use the sun visor, pull it down. You can also use the sun visor at the side window. Remove the support rod from the clip and swing the sun visor toward the side window. In this position, the sun visor can be extended by sliding out the extension. Make sure you put the sun visor back in place when you are getting into or out of the car. Do not use the sun visor extension over the rear view mirror.
Main Menu Table of Contents Sunglasses Holder, Accessory Power Socket Sunglasses Holder On all models except DX To open the sunglasses holder, push on the front edge. It will unlatch and swing down. To close it, push it until it latches. Make sure the holder is closed while you are driving. Accessory Power Socket Some larger styles of sunglasses may not fit in the holder. To use the accessory power socket, pull out on the cover. The ignition switch must be in ACCESSORY (I) or ON (II).
Main Menu Table of Contents Interior Lights Ceiling Light EX, EX-V6 After all doors are closed tightly, the light dims slightly, then fades out in about 10 seconds. In the ON position, the ceiling light stays on continuously. DOOR ACTIVATED The ceiling light has a three-position switch. In the OFF position, the light does not come on. In the center position, the ceiling light comes on when you open any door.
Main Menu Table of Contents Interior Lights Courtesy Lights IGNITION SWITCH LIGHT DOOR LIGHT On all models except DX Each door has a courtesy light. This light comes on when you open the door. Instruments and Controls Your car also has a courtesy light in the ignition switch. This light comes on when you open the driver's door. It remains on for several seconds after the door is closed.
Main Menu Comfort and Convenience Features The heating and air conditioning* systems in your Honda provide a comfortable driving environment in all weather conditions. * Air conditioning is optional on the U.S. DX model. The standard audio system has many features. This section describes those features and how to use them. (If you selected an optional audio system, refer to the operating instructions that came with it.
Main Menu Table of Contents Heating and Cooling Except EX-V6 model Proper use of the Heating and Cooling system can make the interior dry and comfortable, and keep the windows clear for best visibility. If your car does not have air conditioning, it can be installed at any time. Your dealer can install a Genuine Honda air conditioning system that meets Honda's high quality standards and is designed to exactly fit your car. Please contact your dealer for more information.
Main Menu Table of Contents Heating and Cooling Mode Buttons Use the MODE buttons to select the vents the air flows from. Some air will flow from the dashboard corner vents in all modes. Air flows from the center and corner vents in the dashboard. Air flow is divided between the vents in the dashboard and the floor vents. vents. Air flows from the floor Air flow is divided between the floor vents and the defroster vents at the base of the windshield.
Main Menu Table of Contents Heating and Cooling Vent Controls CENTER VENT The direction of air flow from the vents in the center and each side of the dashboard is adjustable. To adjust the air flow from the center vent, move the tab up-anddown and side-to-side. Comfort and Convenience Features DRIVER'S-SIDE VENT On the driver's-side vent, move the vent up-and-down and move the tab side-to-side. On the passenger's-side vent, move the tab up-and-down and move the vent side-to-side.
Main Menu Table of Contents Heating and Cooling How to Use the System This section covers how to set up the system controls for ventilation, heating, cooling, dehumidifying, and defrosting. The engine must be running for the heater and air conditioning to generate hot and cold air. The heater uses engine coolant to warm the air. If the engine is cold, it will be several minutes before you feel warm air coming from the system. The air conditioning does not rely on engine temperature.
Main Menu Table of Contents Heating and Cooling To Cool with A/C 1. Turn on the A / C by pressing the button. The light above the button should come on when a fan speed is selected. 2. Make sure the temperature control dial is set to maximum cool. 3. Select 4. If the outside air is humid, select Recirculation mode. If the outside air is dry, select Fresh Air mode. 5. Set the fan to the desired speed.
Main Menu Table of Contents Heating and Cooling To Heat To warm the interior: 1. Start the engine. 2. Select and Fresh Air mode. 3. Set the fan to the desired speed. 4. Adjust the warmth of the air with the temperature control dial. To Heat and Dehumidify with Air Conditioning Air conditioning, as it cools, removes moisture from the air. When used in combination with the heater, it makes the interior warm and dry. 1. Switch the fan on. 2. Turn on the air conditioning. 3. Select and Fresh Air mode. 4.
Main Menu Table of Contents Heating and Cooling To remove exterior frost or ice from the windshield and side windows after the car has been sitting out in cold weather: 1. Start the engine. 2. Select When you select the system automatically switches to Fresh Air mode and turns on the A/C. 3. Switch the fan and temperature controls to maximum. To rapidly remove exterior frost or ice from the windshield (on very cold days), first select the Recirculation mode.
Main Menu Table of Contents Climate Control System Only on EX-V6 model The automatic climate control system in your Honda picks the proper combination of air conditioning, heating, and ventilation to maintain the interior temperature you select. The system also adjusts the fan speed and air flow levels. CENTER VENTS DRIVER'S-SIDE VENT The direction of air flow from the vents in the center and each side of the dashboard is adjustable.
Main Menu Table of Contents Climate Control System PASSENGER'S-SIDE VENT Comfort and Convenience Features
Main Menu Table of Contents Climate Control System Fully-automatic Operation To put the Automatic Climate Control in fully-automatic mode, press the AUTO button and set the fan control dial to AUTO, then set the desired temperature by turning the temperature control dial. You will see FULL AUTO in the system's display. The light above the button also shows you which mode, Recirculation or Fresh Air, is selected.
Main Menu Table of Contents Climate Control System Semi-automatic Operation You can manually select various functions of the Climate Control system when it is in FULL AUTO. All other features remain automatically controlled. Making any manual selection causes the word FULL to go out. TEMPERATURE CONTROL DIAL AIR CONDITIONING BUTTON Air Conditioning (A/C) Button Press the A/C button to turn the air conditioning on and off. You will see A/C ON or A/C OFF in the display.
Main Menu Table of Contents Climate Control System Recirculation Button This button controls the source of the air going into the system. When the indicator above this button is lit, air from the car's interior is sent through the system again (Recirculation mode). When the indicator is off, air is brought in from outside the car (Fresh Air mode). You can, for example, manually put the system in recirculation mode when driving through an area of smoke or fumes.
Main Menu Table of Contents Climate Control System The main air flow is divided between the floor vents and defroster vents at the base of the windshield. The main air flow comes from the floor vents. The main air flow is divided between the dashboard vents and the floor vents. The main air flow comes from the dashboard vents.
Main Menu Table of Contents Climate Control System The button directs the main air flow to the windshield for faster defrosting. It also overrides any MODE selection you may have made. When you select , the A / C turns on automatically and the system selects Fresh Air mode. For faster defrosting, manually set the fan speed to high. You can also increase air flow to the windshield by closing the side vents in the dashboard.
Main Menu Table of Contents Climate Control System Sunlight Sensor/Temperature Sensor SUNLIGHT SENSOR The climate control system has two sensors. A sunlight sensor is located in the top of the dashboard and a temperature sensor is next to the steering column. Do not cover the sensors or spill any liquid on them.
Main Menu Table of Contents Audio System AM/FM/Cassette Stereo Audio System For DX model Your Honda's audio system provides clear reception on both AM and FM bands, while the preset buttons allow you to easily select your favorite stations. The cassette system features Dolby B* noise reduction, automatic sensing of chromium-dioxide (CrO2) tape, and autoreverse for continuous play. * Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation.
Main Menu Table of Contents Audio System Operating the Radio The ignition switch must be in ACCESSORY (I) or ON (II) to operate the audio system. Turn the system on by pushing the PWR/ VOL knob. Adjust the volume by turning the PWR/VOL knob. The band and frequency that the radio was last tuned to is displayed. To change bands, press the A M / F M button. On the FM band, ST will be displayed if the station is broadcasting in stereo. Stereo reproduction on AM is not available.
Main Menu Table of Contents Audio System SCAN — The SCAN function samples all the stations with strong signals on the selected band. To activate it, press the SCAN button, then release it. The system will scan up the band for a station with a strong signal. When it finds one, it will stop and play that station for approximately five seconds. If you do nothing, the system will then scan for the next strong station and play that for five seconds.
Main Menu Table of Contents Audio System Preset — You can store the frequencies of your favorite radio stations in the six preset buttons. Each button will store one frequency on the AM band, and two frequencies on the FM band. AM/FM BUTTON To store a frequency: 1. Select the desired band, AM or FM. FM1 and FM2 let you store two frequencies with each Preset button. 2. Use the TUNE or SEEK function to tune the radio to a desired station. 3. Pick the Preset button you want for that station.
Main Menu Table of Contents Audio System Adjusting the Sound Balance/Fader — These two controls adjust the strength of the sound coming from each speaker. The Balance control adjusts the sideto-side strength, while the Fader control adjusts the front-to-back strength. BASS/FADER CONTROL TREBLE/BALANCE CONTROL To adjust the fader, push on the BASS/FADER control knob to get it to pop out. Pull it out slightly farther, and adjust the front-to-back sound to your liking.
Main Menu Table of Contents Audio System Operating the Cassette Player Turn the audio system ON. Make sure the tape opening on the cassette is facing to the right, then insert the cassette most of the way into the slot. The system will pull it in the rest of the way, and begin to play. The tape direction indicator will light to show you which side of the cassette is playing. The indicates the side you inserted facing upward is now playing. If you want to play the other side, press the PROG button.
Main Menu Table of Contents Audio System REPEAT — The Repeat function continuously replays the current song or passage. Press the RPT button to activate it; you will see RPT displayed as a reminder. When the system reaches the end of the song or passage currently playing, it will automatically go into rewind. When it senses the beginning of the same song or passage, the system returns to PLAY mode. It will continue to repeat this same program until you deactivate REPEAT by pressing the button again.
Main Menu Table of Contents Audio System The SKIP and REPEAT functions use silent periods on the tape to find the end of a song or passage. These features may not work to your satisfaction if there is almost no gap between selections, a high noise level between selections, or a silent period in the middle of a selection. CASSETTE SLOT EJECT BUTTON RPT BUTTON REW BUTTON TAPE DIRECTION INDICATOR FF BUTTON Caring for Cassettes Damaged cassettes can jam inside the drive or cause other problems.
Main Menu Table of Contents Audio System Operating the Optional CD Changer A Compact Disc changer is available from your dealer. It holds up to six discs, providing several hours of continuous entertainment. You operate the CD changer with the same controls used for the radio and cassette player. TAPE/CD BUTTON RANDOM INDICATOR REPEAT INDICATOR AM/FM BUTTON Your dealer also has an accessory indash single CD player available that is operated by the radio controls.
Main Menu Table of Contents Audio System To operate the CD changer or player, the ignition must be in ACCESSORY (I) or ON (II) and the audio system must be on. Press the CD button until "CD" appears in the display. The system will start to play the first track of the first disc in the magazine. Play only standard round discs. Odd-shaped CDs may jam in the drive or cause other problems. When that disc ends, the next disc in the magazine is loaded and played.
Main Menu Table of Contents Audio System If the system is in Repeat mode, you must turn it off by pressing RPT before you can select Random Play. Then press the button again until you see RDM displayed. RANDOM INDICATOR AM/FM BUTTON REPEAT INDICATOR TAPE/CD BUTTON To take the system out of CD mode, press the A M / F M button or insert a cassette in the player. If a tape is already in the cassette player, press the TAPE button. When you return to CD mode, play will continue at the same disc and track.
Main Menu Table of Contents Audio System CD Changer Error Indications If you see an error indication in the display while operating the CD changer, find the cause in the chart to the right. If you cannot clear the error indication, take the car to your Honda dealer.
Main Menu Table of Contents Audio System AM/FM/CD Audio System For LX model Your Honda's audio system provides clear reception on both AM and FM bands, while the preset buttons allow you to easily select your favorite stations. The anti-theft feature will disable the system if it is disconnected from the vehicle's battery. To get the system working again, you must enter a code number (see page 174 ). Operating the Radio The ignition switch must be in ACCESSORY (I) or ON (II) to operate the audio system.
Main Menu Table of Contents Audio System You can use any of five methods to find radio stations on the selected band: TUNE, SEEK, SCAN, AUTO SELECT, and the Preset buttons. TUNE — Use the TUNE knob to tune the radio to a desired frequency. Turn the knob clockwise to tune to a higher frequency, or counterclockwise to tune to a lower frequency. To change the frequency rapidly, press and hold the top or bottom of the SEEK bar. Release the bar when the display reaches the desired frequency.
Main Menu Table of Contents Audio System Preset — You can store the frequencies of your favorite radio stations in the six preset buttons. Each button will store one frequency on the AM band, and two frequencies on the FM band. AM/FM BUTTON STEREO INDICATOR SCAN INDICATOR SCAN BUTTON To store a frequency: 1. Select the desired band, AM or FM. FM1 and FM2 let you store two frequencies with each Preset button. 2. Use the TUNE, SEEK, or SCAN function to tune the radio to a desired station. 3.
Main Menu Table of Contents Audio System AUTO SELECT — If you are traveling far from home and can no longer receive the stations you preset, you can use the Auto Select feature to find stations in the local area. To activate Auto Select, press the A. SEL button. A. SEL will flash in the display, and the system will go into scan mode for several seconds. It automatically scans both bands, looking for stations with strong signals.
Main Menu Table of Contents Audio System Adjusting the Sound Bass, Treble, Balance, and Fader are each adjustable. You select which of these you want to adjust by pressing the TUNE knob. The mode changes from BAS to TRE to FAD to BAL, and then back to the selected audio mode, each time you press the TUNE knob. Balance/Fader — These two modes adjust the strength of the sound coming from each speaker. BAL adjusts the side-to-side strength, while FAD adjusts the front-to-back strength.
Main Menu Table of Contents Audio System Audio System Lighting You can use the instrument panel brightness control dial to adjust the illumination of the audio system (see page 62 ). The audio system illuminates when the parking lights are on, even if the radio is turned off. Operating the CD Player You operate the CD player with the same controls used for the radio.
Main Menu Table of Contents Audio System You can switch to the radio while a CD is playing by pressing the A M / FM button. Press the CD button to return to playing the CD. The CD will begin playing where it left off. If you turn the system off while a CD is playing, either with the PWR/VOL knob or by turning off the ignition, the disc will stay in the drive. When you turn the system back on, the CD will begin playing where it left off. Press the eject button to remove the disc from the drive.
Main Menu Table of Contents Audio System REPEAT — To activate the Repeat feature, press and release the RPT button. You will see RPT in the display. The system continuously replays the current track. Press the RPT button again to turn it off. RANDOM PLAY — This feature, when activated, plays the tracks on the CD in random order, rather than in the order they are recorded on the CD. To activate Random Play, press the RDM button. You will see RDM in the display.
Main Menu Table of Contents Audio System If you load a CD in the in-dash player while the changer is playing a CD, the system will stop the changer and begin playing the in-dash CD. To select the changer again, press the CD button. Play will begin where it left off. Use the CD button to switch between the player and the changer. If you eject the in-dash CD while it is playing, the system will automatically switch to the CD changer and begin play where it left off.
Main Menu Table of Contents Audio System CD Player Error Indications If you see an error indication in the display while operating the CD player, find the cause in the chart to the right. If you cannot clear the error indication, take the car to your Honda dealer.
Main Menu Table of Contents Audio System CD Changer Error Indications If you see an error indication in the display while operating the CD changer, find the cause in the chart to the right. If you cannot clear the error indication, take the car to your Honda dealer.
Main Menu Table of Contents Audio System Operating the Cassette Player (Optional) The cassette system features Dolby B* noise reduction, automatic sensing of chromium-dioxide (CrO2) tape, and autoreverse for continuous play. AM/FM BUTTON CD/TAPE BUTTON REPEAT BUTTON NR BUTTON Make sure the tape opening on the cassette is facing to the right, then insert the cassette most of the way into the slot. The system will pull it in the rest of the way, and begin to play.
Main Menu Table of Contents Audio System The tape direction indicator will light to show you which side of the cassette is playing. The indicates the side you inserted facing upward is now playing. If you want to play the other side, press the PROG button. Dolby B noise reduction turns on when you insert a cassette. If the tape was not recorded with Dolby B noise reduction, turn it off by pressing the NR button. Dolby remains off until you turn it on by pressing the button again.
Main Menu Table of Contents Audio System Tape Search Functions With a cassette playing, you can use the FF, REW, SKIP, or REPEAT function to find a desired program. Comfort and Convenience Features FF/REW — Fast Forward and Rewind move the tape rapidly. To rewind the tape, push the REW button. You will see REW in the display. To fast forward the tape, push the FF button. You will see FF displayed. Press the PLAY button to take the system out of rewind or fast forward.
Main Menu Table of Contents Audio System REPEAT — The Repeat function continuously replays the current song or passage. Press the RPT button to activate it; you will see RPT displayed as a reminder. When the system reaches the end of the song or passage currently playing, it will automatically go into rewind. When it senses the beginning of the same song or passage, the system returns to PLAY mode. It will continue to repeat this same program until you deactivate REPEAT by pressing the button again.
Main Menu Table of Contents Audio System Look at the cassette before you insert it. If the tape is loose, tighten it by turning a hub with a pencil or your finger. If the label is peeling off, remove it from the cassette or it could cause the cassette to jam in the player. Never try to insert a warped or damaged cassette in the player. Comfort and Convenience Features When they are not in use, store cassettes in their cases to protect them from dust and moisture.
Main Menu Table of Contents Audio System AM/FM/Cassette/CD Changer Audio System For EX and EX-V6 Your Honda's audio system provides clear reception on both AM and FM bands, while the preset buttons allow you to easily select your favorite stations. The cassette system features Dolby B* noise reduction, automatic sensing of chromium-dioxide (CrO2) tape, and autoreverse for continuous play. * Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation.
Main Menu Table of Contents Audio System Operating the Radio The ignition switch must be in ACCESSORY (I) or ON (II) to operate the audio system. Turn the system on by pressing the PWR/ VOL knob or the AM or FM button. Adjust the volume by turning the knob. The band and frequency that the radio was last tuned to is displayed. To change bands, press the AM or FM button. On the FM band, ST will be displayed if the station is broadcasting in stereo. Stereo reproduction on AM is not available.
Main Menu Table of Contents Audio System Preset — You can store the frequencies of your favorite radio stations in the six preset buttons. Each button will store one frequency on the AM band, and two frequencies on the FM band. PWR/VOL KNOB FM BUTTON AM BUTTON STEREO INDICATOR TUNE KNOB To store a frequency: 1. Select the desired band, AM or FM. FM1 and FM2 let you store two frequencies with each Preset button. SEEK BUTTONS 2. Use the TUNE or SEEK function to tune the radio to a desired station.
Main Menu Table of Contents Audio System AUTO SELECT — If you are traveling far from home and can no longer receive the stations you preset, you can use the Auto Select feature to find stations in the local area. To activate Auto Select, press the A. SEL button. A. SEL will flash in the display, and the system will go into scan mode for several seconds. It automatically scans both bands, looking for stations with strong signals.
Main Menu Table of Contents Audio System Adjusting the Sound Bass, Treble, Balance, and Fader are each adjustable. You select which of these you want to adjust by pressing the TUNE knob. The mode changes from BAS to TRE to FAD to BAL, and then back to the selected audio mode, each time you press the TUNE knob. Treble/Bass — Use these modes to adjust the tone to your liking. Select TRE or BAS by pressing the TUNE knob. Adjust the desired mode by turning the TUNE knob.
Main Menu Table of Contents Audio System Audio System Lighting You can use the instrument panel brightness control dial to adjust the illumination of the audio system (see page 63 ). The audio system illuminates when the parking lights are on, even if the radio is turned off. Stations must use these exact frequencies. It is fairly common for stations to round-off the frequency in their advertising, so your radio could display a frequency of 100.
Main Menu Table of Contents Audio System As required by the FCC: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Radio signals, especially on the FM band, are deflected by large objects such as buildings and hills. Your radio then receives both the direct signal from the station's transmitter, and the deflected signal. This causes the sound to distort or flutter.
Main Menu Table of Contents Audio System Operating the Cassette Player The ignition switch must be in ACCESSORY (I) or ON (II). Make sure the tape opening on the cassette is facing to the right, then insert the cassette most of the way into the slot. The system will pull it in the rest of the way, and begin to play. The tape direction indicator will light to show you which side of the cassette is playing. The indicates the side you inserted facing upward is now playing.
Main Menu Table of Contents Audio System Tape Search Functions With a cassette playing, you can use the FF, REW, SKIP, or REPEAT function to find a desired program. F F / R E W — Fast Forward and Rewind move the tape rapidly. To rewind the tape, push the REW button. You will see REW in the display. To fast forward the tape, push the FF button. You will see FF displayed. Press the FF, REW or PLAY button to take the system out of rewind or fast forward.
Main Menu Table of Contents Audio System SKIP — The skip function allows you to find the beginning of a song or passage. To skip to the beginning of a song or passage currently playing, push the button. You will see REW flashing in the display as the tape rewinds. To skip to the beginning of the next song, push the button. You will see FF flashing in the display as the tape fast forwards. When the system finds the beginning of a song or passage, it goes back to PLAY.
Main Menu Table of Contents Audio System REPEAT — The Repeat function continuously replays the current song or passage. Press the RPT button to activate it; you will see RPT displayed as a reminder. When the system reaches the end of the song or passage currently playing, it will automatically go into rewind. When it senses the beginning of the same song or passage, the system returns to PLAY mode. It will continue to repeat this same program until you deactivate REPEAT by pressing the button again.
Main Menu Table of Contents Audio System Caring for the Cassette Player The cassette player picks up dirt and oxides from the tape. This contamination builds up over time and causes the sound quality to degrade. To prevent this, you should clean the player after every 30 hours of use. Your dealer has a cleaning kit available. Look at the cassette before you insert it. If the tape is loose, tighten it by turning a hub with a pencil or your finger.
Main Menu Table of Contents Audio System Operating the CD Changer Your Honda's audio system has an in-dash CD changer that holds up to six discs, providing several hours of continuous entertainment. You operate this CD changer with the same controls used for the radio and cassette player. LOAD BUTTON CD SLOT CD EJECT BUTTON To load the CDs or operate the CD changer, the ignition switch must be in ACCESSORY (I) or ON (II). Load and play only standard round discs.
Main Menu Table of Contents Audio System Loading CDs in the Changer To load multiple CDs in one operation: 1. Press and hold the Load button until you hear a beep and see in the display, then release the button. 2. On the left side of the display, the CD Loaded indicator for an empty position will begin blinking. 3. When you see LOAd in the display, insert the disc into the CD slot. Insert it only about halfway, the drive will pull it in the rest of the way.
Main Menu Table of Contents Audio System If you press the Load button while a CD is playing, the system will stop playing that CD and start the loading sequence. It will then play the CD just loaded. LOAD BUTTON CD LOADED INDICATOR AM BUTTON CD SLOT You can also load a CD into an empty position while a CD is playing by pressing the appropriate preset button. Select an empty position (the CD Loaded indicator is off), and press the preset button for that position (1 to 6).
Main Menu Table of Contents Audio System Operation Select the CD changer by pressing the CD button. You will see "Cd" in the display. The system will begin playing the last selected disc in the CD changer. You will see the disc and track numbers displayed. When that disc ends, the next disc in the CD changer is loaded and played. After the last disc finishes, the system returns to disc 1. To select a different disc, press the appropriate Preset button (1 — 6).
Main Menu Table of Contents Audio System To take the system out of CD mode, press the AM or FM button, or insert a cassette in the player. If a tape is already in the cassette player, press the TAPE button. When you return to CD mode by pressing the CD button, play will continue at the same point that it left off. If you turn the system off while a CD is playing, either with the PWR/VOL knob or the ignition switch, play will continue at the same point when you turn it back on.
Main Menu Table of Contents Audio System Removing CDs from the Changer To remove the disc that is currently playing, press the Eject button. You will see "EJEC" in the display. When you remove the disc from the slot, the system automatically begins the Load sequence so you can load another CD in that position. If you do not load another CD, after ten seconds the system begins playing the next disc in the changer. If the changer is empty, the system selects the previous mode (AM, FM, or Tape).
Main Menu Table of Contents Audio System Protecting Compact Discs Handle a CD by its edges; never touch either surface. Contamination from fingerprints, liquids, felt-tip pens, and labels can cause the CD to not play properly, or possibly jam in the drive. When a CD is not being played, store it in its case to protect it from dust and other contamination. To prevent warpage, keep CDs out of direct sunlight and extreme heat. To clean a disc, use a clean soft cloth.
Main Menu Table of Contents Audio System CD Changer Error Indications If you see an error indication in the display while operating the CD changer, find the cause in the chart to the right. If you cannot clear the error indication, take the car to your Honda dealer.
Main Menu Table of Contents Audio System Remote Audio Controls AUDIO/CH BUTTON The top and bottom buttons adjust the volume up or down Press the proper button and hold it until the desired volume is reached, then release it. The AUDIO/CH button has three functions, depending on whether you are listening to the radio, or playing a cassette or CD. On EX model with leather interior and EX-V6 model Two controls for the audio system are mounted in the steering wheel hub.
Main Menu Table of Contents Audio System Theft Protection On EX, EX-V6 models Your car's audio system will disable itself if it is disconnected from electrical power for any reason. To make it work again, the user must enter a specific five-digit code in the Preset buttons. Because there are hundreds of number combinations possible from five digits, making the system work without knowing the exact code is nearly impossible.
Main Menu Table of Contents Security System On EX and EX-V6 models The security system helps to protect your car and valuables from theft. The horn sounds and a combination of headlights, parking lights, side marker lights and taillights flashes if someone attempts to break into your car or remove the radio. This alarm continues for two minutes, then the system resets. To reset an alarming system before the two minutes have elapsed, unlock either front door with the key or the remote transmitter.
Main Menu 176
Main Menu Before Driving Before you begin driving your Honda, you should know what gasoline to use, and how to check the levels of important fluids. You also need to know how to properly store luggage or packages. The information in this section will help you. If you plan to add any accessories to your car, please read the information in this section first. Break-in Period.............................. 178 Gasoline.......................................... 178 Service Station Procedures ..........
Main Menu Table of Contents Break-in Period, Gasoline, Service Station Procedures Break-in Period Help assure your car's future reliability and performance by paying extra attention to how you drive during the first 600 miles (1,000 km). During this period: Avoid full-throttle starts and rapid acceleration. Avoid hard braking. New brakes need to be broken-in by moderate use for the first 200 miles (300 km).
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Service Station Procedures Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. Stop the engine and keep heat, sparks, and flame away. Handle fuel only outdoors. Wipe up spills immediately. 3. Remove the fuel fill cap slowly. You may hear a hissing sound as pressure inside the tank escapes. Place the cap in the holder on the fuel fill door. 4.
Main Menu Table of Contents Service Station Procedures Opening the Hood HOOD RELEASE HANDLE 1. Shift to Park or Neutral and set the parking brake. Pull the hood release handle located under the lower left corner of the dashboard. The hood will pop up slightly. Before Driving LATCH 2. Standing in front of the car, put your fingers under the front edge of the hood to the right of center. Slide your hand to the left until you feel the hood latch handle. Push this handle up until it releases the hood.
Main Menu Table of Contents Service Station Procedures SUPPORT ROD 4-cylinder models 3. Pull the support rod out of its clip and insert the end into the hole on the front of the hood around the center. To close the hood, lift it up slightly to remove the support rod from the hole. Put the support rod back into its holding clip. Lower the hood to about a foot (30 cm) above the fender, then let it drop. After closing the hood, make sure it is securely latched. 6-cylinder models 3.
Main Menu Table of Contents Service Station Procedures To close the hood, lower it to about a foot (30 cm) above the fender, then press down firmly with your hands. After closing the hood, make sure it is securely latched. Oil Check 4-cylinder models DIPSTICK Check the engine oil level every time you fill the car with fuel. Wait a few minutes after turning the engine off before you check the oil. 1. Remove the dipstick (orange handle).
Main Menu Table of Contents Service Station Procedures 4-cylinder models 2. Wipe the dipstick with a clean cloth or paper towel. 6-cylinder models 3. Insert it all the way back in its tube.
Main Menu Table of Contents Service Station Procedures Engine Coolant Check RESERVE TANK MAX MAX RESERVE TANK UPPER MARK LOWER MARK 4-cylinder models 4. Remove the dipstick again and check the level. It should be between the upper and lower marks. If it is near or below the lower mark, see Adding Oil on page 234 . Before Driving MIN Look at the coolant level in the radiator reserve tank. Make sure it is between the MAX and MIN lines.
Main Menu Table of Contents Fuel Economy The condition of your car and your driving habits are the two most important things that affect the fuel mileage you get. Vehicle Condition Always maintain your car according to the maintenance schedule. This will keep it in top operating condition. An important part of that maintenance is the Owner Maintenance Checks (see page 231). For example, an underinflated tire causes more "rolling resistance," which uses fuel.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Accessories and Modifications Modifying your car, or installing some non-Honda accessories, can make your car unsafe. Before you make any modifications or add any accessories, be sure to read the following information. Accessories Your dealer has Genuine Honda accessories that allow you to personalize your car. These accessories have been designed and approved for your car, and are covered by warranty.
Main Menu Table of Contents Accessories and Modifications Modifications Do not remove any original equipment or modify your car in any way that would alter its design or operation. This could make your car unsafe and illegal to drive. In addition, any modifications that decrease ground clearance increase the chance of undercarriage parts striking a curb, speed bump, or other raised object, which could cause your airbags to deploy.
Main Menu Table of Contents Carrying Cargo CONSOLE COMPARTMENT FRONT DOOR POCKET Your car has several convenient storage areas so you can stow cargo safely. The glove box, and the pockets in the front doors and seat-backs, are designed for small, lightweight items. The trunk is intended for larger, heavier items. In addition, the back seat can be folded down to allow you to carry more cargo or longer items.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Carrying Cargo Load Limit The maximum load for your car is 850 lbs (395 kg). This figure includes the total weight of all occupants, cargo, accessories, and the tongue weight if you are towing a trailer. To figure out how much cargo you can carry: Add up the weight of all occupants. If you are towing a trailer, add the tongue weight to the number above. Subtract the total from 850 Ibs (395 kg).
Main Menu Table of Contents Carrying Cargo Carrying Cargo in the Trunk or on a Roof Rack Distribute cargo evenly on the floor of the trunk, placing the heaviest items on the bottom and as far forward as possible. If you fold down the back seat, tie down items that could be thrown about the car during a crash or sudden stop. If you carry large items that prevent you from closing the trunk lid, exhaust gas can enter the passenger area.
Main Menu Driving This section gives you tips on starting the engine under various conditions, and how to operate the 5-speed manual and automatic transmissions. It also includes important information on parking your car, the braking system, and facts you need if you are planning to tow a trailer. Preparing to Drive......................... 192 Starting the Engine........................ 193 Starting in Cold Weather at High Altitude ..................... 194 5-speed Manual Transmission.....
Main Menu Table of Contents Preparing to Drive You should do the following checks and adjustments every day before you drive your car. 1. Make sure all windows, mirrors, and outside lights are clean and unobstructed. Remove frost, snow, or ice. 2. Check that the hood and trunk are fully closed. 3. Visually check the tires. If a tire looks low, use a gauge to check its pressure. 4. Check that any items you may be carrying with you inside are stored properly or fastened down securely. Driving 5.
Main Menu Table of Contents Starting the Engine 1. Apply the parking brake. 2. In cold weather, turn off all electrical accessories to reduce the drain on the battery. 3. Manual Transmission: Push the clutch pedal down all the way. START (III) does not function unless the clutch pedal is depressed. Automatic Transmission: Make sure the shift lever is in Park. Press on the brake pedal. 4. Without touching the accelerator pedal, turn the ignition key to the START (III) position.
Main Menu Table of Contents Starting the Engine Starting in Cold Weather at High Altitude (Above 8,000 feet/ 2,400 meters) An engine is harder to start in cold weather. The thinner air found at high altitude above 8,000 feet (2,400 meters) adds to the problem. Use the following procedure: 1. Turn off all electrical accessories to reduce the drain on the battery. 2. Push the accelerator pedal halfway to the floor and hold it there while starting the engine.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 5-speed Manual Transmission Come to a full stop before you shift into Reverse. You can damage the transmission by trying to shift into Reverse with the car moving. Push down the clutch pedal, and pause for a few seconds before shifting into Reverse, or shift into one of the forward gears for a moment. This stops the gears so they won't "grind." The manual transmission is synchronized in all forward gears for smooth operation.
Main Menu Table of Contents 5-speed Manual Transmission, Automatic Transmission Recommended Shift Points Drive in the highest gear that lets the engine run and accelerate smoothly. This will give you the best fuel economy and effective emissions control. The following shift points are recommended: Engine Speed Limiter If you exceed the maximum speed for the gear you are in, the engine speed will enter into the tachometer's red zone.
Main Menu Table of Contents Automatic Transmission Shift Lever Position Indicator Shift Lever Positions SHIFT LEVER This indicator between the fuel gauge and temperature gauge shows which position the shift lever is in. The "D4" indicator comes on for a few seconds when you turn the ignition switch ON (II). If it flashes while driving (in any shift position), it indicates a possible problem in the transmission.
Main Menu Table of Contents Automatic Transmission Neutral (N) — Use Neutral if you need to restart a stalled engine, or if it is necessary to stop briefly with the engine idling. Shift to Park position if you need to leave the car for any reason. Press on the brake pedal when you are moving the shift lever from Neutral to another gear. Park (P) — This position mechanically locks the transmission. Use Park whenever you are turning off or starting the engine.
Main Menu Table of Contents Automatic Transmission Drive (D3) —This position is similar to D4, except only the first three gears are selected. Use D3 when towing a trailer in hilly terrain, or to provide engine braking when going down a steep hill. D3 can also keep the transmission from cycling between third and fourth gears in stop-and-go driving. For faster acceleration when in D3 or D4, you can get the transmission to automatically downshift by pushing the accelerator pedal to the floor.
Main Menu Table of Contents Automatic Transmission Engine Speed Limiter If you exceed the maximum speed for the gear you are in, the engine speed will enter into the tachometer's red zone. If this occurs, you may feel the engine cut in and out. This is caused by a limiter in the engine's computer controls. The engine will run normally when you reduce the RPM below the red zone.
Main Menu Table of Contents Automatic Transmission If you need to use the Shift Lock Release, it means your car is developing a problem. Have the car checked by your Honda dealer. 5. Push down on the key while you press the release button on the shift lever and move the shift lever out of Park to Neutral. 6. Remove the key from the Shift Lock Release slot, then reinstall the cover. Make sure the notch on the cover is on the left side. Depress the brake pedal and restart the engine.
Main Menu Table of Contents Parking Always use the parking brake when you park your car. The indicator on the instrument panel shows that the parking brake is not fully released; it does not indicate that the parking brake is firmly set. Make sure the parking brake is set firmly or your car may roll if it is parked on an incline. If the car is facing uphill, turn the front wheels away from the curb. If you have a manual transmission, put it in first gear.
Main Menu Table of Contents The Braking System Your Honda is equipped with front disc brakes. The brakes on the rear wheels may be disc or drum, depending on the model. A power assist helps reduce the effort needed on the brake pedal. Put your foot on the brake pedal only when you intend to brake. Resting your foot on the pedal keeps the brakes applied lightly, causing them to build up heat. Heat build-up can reduce how well your brakes work.
Main Menu Table of Contents The Braking System Brake System Design The hydraulic system that operates the brakes has two separate circuits. Each circuit works diagonally across the vehicle (the left-front brake is connected with the right-rear brake, etc.). If one circuit should develop a problem, you will still have braking at two wheels. Anti-lock Brakes LX with ABS, EX and all V6 models have an Anti-lock Brake System (ABS) as standard equipment. It is optional on other models.
Main Menu Table of Contents The Braking System Important Safety Reminders ABS does not reduce the time or distance it takes to stop the car, it only helps with steering control during braking. You should always maintain a safe following distance from other vehicles. ABS will not prevent a skid that results from changing direction abruptly, such as trying to take a corner too fast or making a sudden lane change. Always drive at a safe, prudent speed for the road and weather conditions.
Main Menu Table of Contents Traction Control System On LX V6 and EX V6 models Your Honda is equipped with a Traction Control System (TCS) to assist you in maintaining traction while driving slowly on loose or slippery surfaces. The TCS assists only in low-speed, low-traction conditions; up to approximately 18 mph (30km/h). The TCS monitors the speed of all four wheels. When it senses a front wheel losing traction, it applies braking to that wheel. The TCS indicator flashes when this occurs.
Main Menu Table of Contents Traction Control System TCS ON/OFF Switch Deactivate the system by pressing the TCS On/Off switch. The TCS indicator light comes on as a reminder. Pressing the switch again turns the system back on. The Traction Control System turns on every time you start the engine, even if you turned it off the last time you drove the vehicle. TCS Indicator The TCS indicator comes on or flashes under the following conditions: When you turn the ignition switch to ON (II).
Main Menu Table of Contents Traction Control System If the TCS indicator comes on while driving, pull to the side of the road when it is safe and turn off the engine. Reset the system by restarting the engine, and watch the TCS indicator. If the indicator remains on, or comes back on while driving, have the TCS inspected by your Honda dealer. You can still drive the vehicle without TCS. The TCS indicator may occasionally come on for one or two seconds and then go out. This is normal.
Main Menu Table of Contents Driving in Bad Weather Rain, fog, and snow conditions require a different driving technique because of reduced traction and visibility. Keep your car wellmaintained and exercise greater caution when you need to drive in bad weather. The cruise control should not be used in these conditions. Driving Technique — Always drive slower than you would in dry weather. It takes your car longer to react, even in conditions that may seem just barely damp.
Main Menu Table of Contents Driving in Bad Weather Visibility — Being able to see clearly in all directions and being visible to other drivers are important in all weather conditions. This is more difficult in bad weather. To be seen more clearly during daylight hours, turn on your headlights. Traction — Check your tires frequently for wear and proper pressure. Both are important in preventing "hydroplaning" (loss of traction on a wet surface).
Main Menu Table of Contents Towing a Trailer Your Honda has been designed primarily to carry passengers and their cargo. You can use it to tow a trailer if you carefully observe the load limits, use the proper equipment, and follow the guidelines in this section. Load Limits Total Trailer Weight: The total weight of the trailer and everything loaded in it must not exceed 1,000 Ibs (450 kg). Towing a load that is too heavy can seriously affect your vehicle's handling and performance.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Towing a Trailer To achieve a proper tongue load, start by loading 60 percent of the load toward the front of the trailer and 40 percent toward the rear, then re-adjust the load as needed.
Main Menu Table of Contents Towing a Trailer Towing Equipment and Accessories Towing can require a variety of equipment, depending on the size of your trailer, how it will be used, and how much load you are towing. Discuss your needs with your trailer sales or rental agency, and follow the guidelines in the rest of this section. Also make sure that all equipment is properly installed and that it meets federal, state, province, and local regulations.
Main Menu Table of Contents Towing a Trailer Trailer Lights Your vehicle has a trailer lighting connector in the trunk. Refer to the drawing in this page for the wiring color code and purpose of each pin. GROUND (BLACK) BACK-UP LIGHT (GREEN/BLACK) LEFT TURN SIGNAL (GREEN/BLUE) If you use a converter, you can get the connector and pins that mate with the connector in your vehicle from your Honda dealer.
Main Menu Table of Contents Towing a Trailer Additional Trailer Equipment Many states and Canadian provinces require special outside mirrors when towing a trailer. Even if they don't, you should install special mirrors if you cannot clearly see behind you, or if the trailer creates a blind spot. Ask your trailer sales or rental agency if any other items are recommended or required for your towing situation.
Main Menu Table of Contents Towing a Trailer Driving Safely With a Trailer The added weight, length, and height of a trailer will affect your vehicle's handling and performance, so driving with a trailer requires some special driving skills and techniques. For your safety and the safety of others, take time to practice driving maneuvers before heading for the open road, and follow the guidelines discussed below.
Main Menu Table of Contents Towing a Trailer Handling Crosswinds and Buffeting Crosswinds and air turbulence caused by passing trucks can disrupt your steering and cause trailer swaying. When being passed by a large vehicle, keep a constant speed and steer straight ahead. Do not try to make quick steering or braking corrections. Parking Follow all normal precautions when parking, including firmly setting the parking brake and putting the transmission in Park (automatic) or in 1st or Reverse (manual).
Main Menu 218
Main Menu Maintenance This section explains why it is important to keep your car well maintained and to follow basic maintenance safety precautions. This section also includes Maintenance Schedules for normal driving and severe driving conditions, a Maintenance Record, and instructions for simple maintenance tasks you may want to take care of yourself. If you have the skills and tools to perform more complex maintenance tasks on your Honda, you may want to purchase the Service Manual.
Main Menu Table of Contents Maintenance Safety Some of the most important safety This section includes instructions for Regularly maintaining your car is the precautions are given here. However, simple maintenance tasks, such as best way to protect your investment. 03/07/10 16:11:09 31S5A930 0021and adding oil.
Main Menu Table of Contents Maintenance Safety Important Safety Precautions Before you begin any maintenance, make sure your car is parked on level ground and that the parking brake is set. Also, be sure the engine is off. This will help to eliminate several potential hazards: Carbon monoxide poisoning from engine exhaust. Be sure there is adequate ventilation whenever you operate the engine. Burns from hot parts. Let the engine and exhaust system cool before touching any parts. Injury from moving parts.
Main Menu Table of Contents Maintenance Schedule The Maintenance Schedule specifies how often you should have your car serviced and what things need attention. It is essential that you have your car serviced as scheduled to retain its high level of safety, dependability, and emissions control performance. The services and time or distance intervals shown in the maintenance schedule assume you will use your vehicle as normal transportation for passengers and their possessions.
Main Menu Table of Contents Maintenance Schedule Your authorized Honda dealer knows your car best and can provide competent, efficient service. However, service at a dealer is not mandatory to keep your warranties in effect. Maintenance may be done by any qualified service facility or person who is skilled in this type of automotive service. Keep all the receipts as proof of completion, and have the person who does the work fill out the Maintenance Record. Check your warranty booklet for more information.
Main Menu Table of Contents U.S. Owners Follow the Normal Conditions Maintenance Schedule if the severe driving conditions specified in the Severe Conditions Maintenance Schedule do not apply. NOTE: If you only OCCASIONALLY drive under a "severe" condition, you should follow the Normal Conditions Maintenance Schedule. Canadian Owners Follow the Maintenance Schedule for Severe Conditions. * * # : See information on maintenance and emissions warranty, last column, page 223.
Main Menu Table of Contents Service at the indicated distance or time, whichever comes first. Do the items in A, B, C as required for each distance/time interval. Follow this schedule if the severe driving conditions described in the Severe Conditions Schedule on the next page do not apply. Canadian owners: Follow the schedule for Severe Conditions. page 271 # : See information on maintenance and emissions warranty, last column, page 223. 1 : Balancer belt applies to 4-cylinder models only.
Main Menu Table of Contents U.S. Owners Follow the Severe Conditions Maintenance Schedule if you drive your vehicle MAINLY under one or more of the following conditions: Driving less than 5 miles (8 km) per trip or, in freezing temperatures, driving less than 10 miles (16 km) per trip. Driving in extremely hot [over 90°F (32°C)] conditions. Extensive idling or long periods of stop-and-go driving. Trailer towing, driving with a car top carrier, or driving in mountainous conditions.
Main Menu Table of Contents Use this schedule if your vehicle is MAINLY driven in any of the following Severe Conditions, or normally driven in Canada; otherwise use the Normal Schedule. Service at the indicated distance or time, whichever comes first. Do the items in A, B, C, D as required for each distance/time.
Main Menu Table of Contents # : See information on maintenance and emissions warranty, last column, page 223. 1 : See timing belt on page 267 to determine need for replacement. 2 : Balancer belt applies to 4-cylinder models only. 3 : See air conditioning filter on page 266 for replacement information under special driving conditions. NOTE: Check engine oil and coolant at each fuel stop. Check and adjust valve clearance, cold engine, only if noisy.
Main Menu Table of Contents Required Maintenance Record (for Normal and Severe Schedules) You or the servicing dealer can record all completed maintenance here, whether you follow the schedule for normal conditions (page 224) or severe conditions (page 226 ). Keep the receipts for all work done on your vehicle.
Main Menu Table of Contents Required Maintenance Record (for Normal and Severe Schedules) Maintenance
Main Menu Table of Contents Owner Maintenance Checks You should check the following items at the specified intervals. If you are unsure of how to perform any check, turn to the page given. Engine oil level — Check every time you fill the fuel tank. See page 182. Engine coolant level — Check the radiator reserve tank every time you fill the fuel tank. See page 184 . Windshield washer fluid — Check the level in the reservoir monthly.
Main Menu Table of Contents Fluid Locations 4-cylinder Models BRAKE FLUID (Gray cap) CLUTCH FLUID (5-speed Manual Transmission only) (Gray cap) ENGINE OIL FILL CAP ENGINE OIL DIPSTICK (Orange loop) AUTOMATIC TRANSMISSION FLUID DIPSTICK (Yellow loop) WASHER FLUID (Blue cap) COOLANT RESERVOIR POWER STEERING FLUID (Red cap) RADIATOR CAP Maintenance
Main Menu Table of Contents Fluid Locations 6-cylinder Models ENGINE OIL FILL CAP BRAKE FLUID (Gray cap) ENGINE OIL DIPSTICK (Orange loop) AUTOMATIC TRANSMISSION FLUID DIPSTICK (Yellow loop) WASHER FLUID (Blue cap) COOLANT RESERVOIR POWER STEERING FLUID (Red cap) RADIATOR CAP Maintenance
Main Menu Table of Contents Engine Oil Adding Oil ENGINE OIL FILL CAP ENGINE OIL FILL CAP 4-cylinder models 6-cylinder models To add oil, unscrew and remove the engine oil fill cap on top of the valve cover. Pour in the oil, and install the engine oil fill cap. Tighten it securely. Wait a few minutes and recheck the oil level. Do not fill above the upper mark; you could damage the engine.
Main Menu Table of Contents Engine Oil Recommended Oil Oil is a major contributor to your engine's performance and longevity. Always use a premium-grade 5W-20 detergent oil displaying the API Certification Seal. This seal indicates the oil is energy conserving, and that it meets the American Petroleum Institute's latest requirements. Genuine Honda Motor Oil is the preferred 5W-20 lubricant for your vehicle.
Main Menu Table of Contents Engine Oil Changing the Oil and Filter Always change the oil and filter according to the time and distance (miles/kilometers) recommendations in the maintenance schedule. The oil and filter collect contaminants that can damage your engine if they are not removed regularly. Maintenance Changing the oil and filter requires special tools and access from underneath the car. The car should be raised on a service station-type hydraulic lift for this service.
Main Menu Table of Contents Engine Oil WASHER DRAIN BOLT 4-cylinder models 2. Open the hood and remove the engine oil fill cap. Remove the oil drain bolt and washer from the bottom of the engine. Drain the oil into an appropriate container. WASHER DRAIN BOLT 6-cylinder models 3. Remove the oil filter and let the remaining oil drain. A special wrench (available from your Honda dealer) is required to remove the filter. OIL FILTER 4-cylinder models 4.
Main Menu Table of Contents Engine Oil OIL FILTER 7. Replace the engine oil fill cap. Start the engine. The oil pressure indicator light should go out within five seconds. If it does not, turn off the engine and reinspect your work. 8. Let the engine run for several minutes and check the drain bolt and oil filter for leaks. 6-cylinder models 6. Refill the engine with the recommended oil. Engine oil change capacity (including filter): (4-cylinder models) 4.5 US qt (4.3 , 3.
Main Menu Table of Contents Cooling System Adding Engine Coolant coolant can result in corrosion, causing the cooling system to malfunction or fail. Have the cooling system flushed and refilled with Honda antifreeze/coolant as soon as possible. If the reserve tank is completely empty, you should also check the coolant level in the radiator. 4-cylinder models RESERVE TANK If the coolant level in the reserve tank is at or below the M I N line, add coolant to bring it up to the MAX line.
Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Cooling System Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you. RADIATOR CAP Always let the engine and radiator cool down before removing the radiator cap. 4-cylinder models 1. Make sure the engine and radiator are cool. 2. Turn the radiator cap counterclockwise, without pressing down on it, until it stops. This relieves any pressure remaining in the cooling system.
Main Menu Table of Contents Cooling System Replacing Engine Coolant The cooling system should be completely drained and refilled with new coolant according to the time and distance recommendations in the maintenance schedule. Only use Honda All season Antifreeze/ Coolant Type 2. 4 cylinder models RESERVE TANK 6. Pour coolant into the reserve tank. Fill it to halfway between the MAX and M I N marks. Put the cap back on the reserve tank.
Main Menu Table of Contents Cooling System DRAIN BOLT DRAIN PLUG 4-cylinder models 1. Open the hood. Make sure the engine and radiator are cool to the touch. Except EX- V6 model Turn the ignition ON (II). Turn the temperature control Dial all the way clockwise. Turn off the ignition and remove the key. Maintenance 6-cylinder models EX-V6 model Turn the ignition ON (II). Turn the temperature control dial to 90°F (32° C). Turn off the ignition and remove the key. 2. Remove the radiator cap.
Main Menu Table of Contents Cooling System DRAIN PLUG 6-cylinder models 6-cylinder models RESERVE TANK DRAIN BOLT 3. Loosen the drain plug on the bottom of the radiator. The coolant will drain through the splash guard. Loosen the drain bolt. 4-cylinder models RESERVE TANK CAP HOLDER 4. Remove the reserve tank from its holder by pulling it straight up. Drain the coolant, then put the tank back in its holder.
Main Menu Table of Contents Cooling System RESERVE TANK 6-cylinder models RESERVE TANK CAP HOLDER 5. When the coolant stops draining, tighten the drain plug at the bottom of the radiator. 6. 4-cylinder models Put a new washer on the drain bolt, then reinstall the drain bolt in the engine block. Tighten it securely. Tightening torque: 61 Ibf.ft (83 N.m , 8.5 kgf.
Main Menu Table of Contents Cooling System 8. Start the engine and let it run for about 30 seconds. Then turn off the engine. 9. Fill the radiator with coolant up to the base of the filler neck. 10. Fill the reserve tank to the MAX mark. Install the reserve tank cap. 4-cylinder models BLEEDER BOLT 6-cylinder models Pour coolant into the radiator up to the base of the filler neck. The cooling system capacity is: With 5-speed manual transmission: 1.45 US gal (5.5 ,1.21 Imp gal) 1.43 US gal (5.4 ,1.
Main Menu Table of Contents Windshield Washers Check the level in the windshield washer reservoir at least monthly during normal usage. In bad weather, when you use the washers often, check the level every time you stop for fuel. LEVEL GAUGE The windshield washer reservoir is located behind the headlight. Check the reservoir's fluid level by removing the cap and looking at the level gauge attached to the cap.
Main Menu Table of Contents Transmission Fluid Automatic Transmission 4-cylinder models UPPER MARK LOWER MARK DIPSTICK Check the fluid level with the engine at normal operating temperature. 1. Park the car on level ground. Shut off the engine. 2. Remove the dipstick (yellow loop) from the transmission and wipe it with a clean cloth. 3. Insert the dipstick all the way into the transmission securely as shown in the illustration. 4. Remove the dipstick and check the fluid level.
Main Menu Table of Contents Transmission Fluid 6. Insert the dipstick all the way back into the transmission securely as shown in the illustration. Automatic Transmission 6-cylinder models The transmission should be drained and refilled with new fluid according to the time and distance recommendations in the maintenance schedule. UPPER MARK DIPSTICK Check the fluid level with the engine at normal operating temperature. 1. Park the car on level ground. Shut off the engine. 2.
Main Menu Table of Contents Transmission Fluid 5. If the level is below the lower mark, add fluid into the tube to bring it to the upper mark. Always use Honda ATF-Z1 (Automatic Transmission Fluid). If it is not available, you may use a DEXRON® III automatic transmission fluid as a temporary replacement. However, continued use can affect shift quality. Have the transmission drained and refilled with Honda ATF- Zl as soon as it is convenient.
Main Menu Table of Contents Transmission Fluid If Honda MTF is not available, you may use an API service SG, SH or SJ grade motor oil with a viscosity of SAE 10W-30 or 10W-40 as a temporary replacement. An SG grade is preferred, but an SH or SJ grade may be used if SG is not available. However, motor oil does not contain the proper additives and continued use can cause stiffer shifting. Replace as soon as it is convenient.
Main Menu Table of Contents Brake and Clutch Fluid Check the fluid level in the reservoirs monthly. There are up to two reservoirs, depending on the model. They are: Brake fluid reservoir (all models) Clutch fluid reservoir (manual transmission only) The brake fluid should be replaced according to the time and distance recommendations in the maintenance schedule. Always use Honda DOT 3 brake fluid.
Main Menu Table of Contents Brake and Clutch Fluid, Power Steering Clutch System UPPER LEVEL 6 cylinder models Power Steering LOWER LEVEL MIN The fluid should be between the MIN and MAX marks on the side of the reservoir. If it is not, add brake fluid to bring it up to that level. Use the same fluid specified for the brake system. Low fluid level can indicate a leak in the clutch system. Have this system inspected as soon as possible.
Main Menu Table of Contents Power Steering, Air Cleaner Element UPPER LEVEL 6-cylinder models LOWER LEVEL Always use Honda Power Steering Fluid. If it is not available, you may use another power steering fluid as an emergency replacement. However, continued use can cause increased wear and poor steering in cold weather. Have the power steering system flushed and refilled with Honda PSF as soon as possible. A low power steering fluid level can indicate a leak in the system.
Main Menu Table of Contents Air Cleaner Element (4-cylinder Models) Replacement The air cleaner element is inside the air cleaner housing on the passenger's side of the engine compartment. To replace it: CLAMPS AIR CLEANER ELEMENT 1. Unsnap the four hold-down clamps and remove the air cleaner housing cover. 2. Remove the old air cleaner element. 3. Carefully clean the inside of the air cleaner housing with a damp rag. Maintenance 4. Place the new air cleaner element in the air cleaner housing. 5.
Main Menu Table of Contents Air Cleaner Element (6-cylinder Models) Replacement The air cleaner element is inside the air cleaner housing on the driver's side of the engine compartment. To replace it: BOLTS AIR CLEANER ELEMENT 1. Loosen the four bolts and remove the air cleaner housing cover. 4. Place the new air cleaner element in the air cleaner housing. 2. Remove the old air cleaner element. 5. Reinstall the air cleaner housing cover, tighten the four bolts. 3.
Main Menu Table of Contents Hood Latch, Spark Plugs (4-cylinder Models) Hood Latch LATCH ASSEMBLY Clean the hood latch assembly with a mild cleaner, then lubricate it with a multipurpose grease. Lubricate all the moving parts, including the pivot. Follow the time and distance recommendations in the Maintenance Schedule. If you are not sure how to clean and grease the latch, contact your Honda dealer.
Main Menu Table of Contents Spark Plugs (4-cylinder Models) NOTICE Tighten the spark plugs carefully. A spark plug that is too loose can overheat and damage the engine. Ovcrtiglitening can cause damage to the threads in the cylinder head. 6. Install the spark plug cap. 7. Repeat this procedure for the other three spark plugs. 4. Put the new spark plug into the socket; then screw it into the hole. Screw it in by hand so you do not crossthread it. 5. Torque the spark plug.
Main Menu Table of Contents Spark Plugs (6-cylinder Models) The spark plugs in your car should be replaced according to the time and distance recommendations in the maintenance schedule. Replacement HEXAGON SOCKET HEAD CAP BOLT 2. Clean up any dirt and oil that have collected around the ignition coils. HOLDING CLIP 1. Loosen the two holding clips by turning the heads one-quarter turn counterclockwise with a flat-tipped screwdriver. Remove the cover on the front cylinder bank by pulling it straight up.
Main Menu Table of Contents Spark Plugs (6-cylinder Models) 9. Push the wire connector onto the ignition coil. Make sure it locks in place. 10. Repeat this procedure for the other five spark plugs. 6. Put the new spark plug into the socket; then screw it into the hole. Screw it in by hand so you do not crossthread it. 7. Torque the spark plug. (If you do not have a torque wrench, tighten the spark plug two-thirds of a turn after it contacts the cylinder head.) Tightening torque: 13 lbf.ft (18 N.m , 1.
Main Menu Table of Contents Battery Check the condition of your car's battery monthly. You should check the color of the test indicator window, and for corrosion on the terminals. TEST INDICATOR WINDOW TEST INDICATOR WINDOW 4-cylinder models 6-cylinder models Check the battery condition by looking at the test indicator window on the battery. The label on the battery explains the test indicator's colors. Maintenance Check the battery terminals for corrosion (a white or yellowish powder).
Main Menu Table of Contents Battery WARNING: Battery posts, terminals and related accessories contain lead and lead compounds. Wash hands after handling. 4 cylinder models If the terminals are severely corroded, clean them with baking soda and water. Then use a wrench to loosen and remove the cables from the terminals. Always disconnect the negative (—) cable first and reconnect it last. Clean the battery terminals with a terminal cleaning tool or wire brush.
A Few 0021 Words About Safety Main 16:11:09 Menu Table of31S5A930 Contents 03/07/10 Battery Your safety, and the safety of others, You will find this important safety information in a variety is very important. And operating this including: vehicle safely is16:11:09 an important 31S5A930 0021 03/07/10 03/07/10 16:11:09 31S5A930 0021 Safety Labels − on the vehicle. responsibility.
Main Menu Table of Contents Wiper Blades Check the condition of the wiper blades at least every six months. Look for signs of cracking in the rubber, or areas that are getting hard. Replace the blades if you find these signs, or they leave streaks and unwiped areas when used. WIPER ARMS LOCK TAB To replace the blade: 1. Raise the wiper arm off the windshield. Raise the driver's side first, then the passenger's side. 2. Disconnect the blade assembly from the wiper arm by pushing in the lock tab.
Main Menu Table of Contents Wiper Blades BLADE BLADE 5. Slide the new wiper blade into the holder until the tabs lock. 6. Slide the wiper blade assembly onto the wiper arm. Make sure it locks in place. REINFORCEMENT 3. Remove the blade from its holder by grasping the tabbed end of the blade. Pull firmly until the tabs come out of the holder. Maintenance 4. Examine the new wiper blades.
Main Menu Table of Contents Air Conditioning System Optional for U.S. DX model Your car's air conditioning is a sealed system. Any major maintenance, such as recharging, should be done by a qualified mechanic. You can do a couple of things to make sure the air conditioning works efficiently. Periodically check the engine's radiator and air conditioning condenser for leaves, insects, and dirt stuck to the front surface. These block the air flow and reduce cooling efficiency.
Main Menu Table of Contents Air Conditioning Filter, Drive Belts Air Conditioning Filter The air conditioning filter removes pollen and dust that is brought in from the outside through the heating and cooling system. This filter should be replaced every 30,000 miles (48,000 km) under normal conditions. It should be replaced every 15,000 miles (24,000 km) if you drive primarily in urban areas that have high concentrations of soot in the air from industry and diesel-powered vehicles.
Main Menu Table of Contents Drive Belts, Timing Belt, Tires 6-cylinder models Power steering belt: 0.51 — 0.65 in (13.0 — 16.5 mm) If you see signs of wear or looseness, have your dealer adjust or replace the belts. Timing Belt The timing belt and balancer belt should normally be replaced at the intervals shown in the maintenance schedule. Tires To safely operate your car, your tires must be the proper type and size, in good condition with adequate tread, and correctly inflated.
Main Menu Table of Contents Tires Inflation Keeping the tires properly inflated provides the best combination of handling, tread life and riding comfort. Underinflated tires wear unevenly, adversely affect handling and fuel economy, and are more likely to fail from being overheated. Overinflated tires can make your car ride more harshly, are more prone to damage from road hazards, and wear unevenly. We recommend that you visually check your tires every day.
Main Menu Table of Contents Tires Recommended Tire Pressures for Normal Driving The following chart shows the recommended cold tire pressures for most normal driving conditions and speeds. Tire pressures for high speed driving are the same as for normal driving. The compact spare tire pressure is: 60 psi (420 kPa , 4.2 kgf/cm2 ) Tubeless tires have some ability to self-seal if they are punctured.
Main Menu Table of Contents Tires Inspection Every time you check inflation, you should also examine the tires for damage, foreign objects, and wear. INDICATOR LOCATION MARKS You should look for: Bumps or bulges in the tread or side of the tire. Replace the tire if you find either of these conditions. Cuts, splits, or cracks in the side of the tire. Replace the tire if you can see fabric or cord. Excessive tread wear.
Main Menu Table of Contents Tires Make sure the installer balances the wheels when you have new tires installed. This increases riding comfort and tire life. Your car's original tires were dynamic or "spin" balanced at the factory. For best results, have the installer perform a dynamic balance. Tire Rotation Front Front NOTICE (LX with ABS ,EX,EX-V6) Improper wheel weights can damage your car's aluminum wheels. Use only Genuine Honda wheel weights for balancing.
Main Menu A Few Words About Safety Main Menu Table of Contents 03/07/10 16:11:09 31S5A930 0021 Tires Your safety, and the safety of others, You will find this important safety information in a variety is very important. And operating this including: vehicle safely is16:11:09 an important 31S5A930 0021 03/07/10 03/07/10 16:11:09 31S5A930 0021 Wheels and The ABS works by comparing the Safety Labels − Tires responsibility. on the vehicle. Wheel: speed of the wheels.
Main Menu Table of Contents Tires Winter Driving Tires that are marked "M + S" or "All Season" on the sidewall have an all-weather tread design. They should be suitable for most winter driving conditions. Tires without these markings are designed for optimum traction in dry conditions. They may not provide adequate performance in winter driving. For the best performance in snowy or icy conditions, you should install snow tires or tire chains. They may be required by local laws under certain conditions.
Main Menu Table of Contents Lights Check the operation of your car's exterior lights at least once a month. A burned out bulb can create an unsafe condition by reducing your car's visibility and the ability to signal your intentions to other drivers.
Main Menu Table of Contents Lights HIGH-MOUNT BRAKE LIGHT BACK-UP LIGHT Check the following: Headlights (low and high beam) Parking lights Taillights Brake lights High-mount brake light Turn signals Back-up lights Hazard light function License plate light Side marker lights Daytime running lights (Canadian models) If you find any bulbs are burned out, replace them as soon as possible. Refer to the chart on page 327 to determine what type of replacement bulb is needed.
Main Menu Table of Contents Lights Headlight Aiming The headlights were properly aimed when your car was new. If you regularly carry heavy items in the trunk, readjustment may be required. Adjustment of the headlights should be performed by a Honda technician or other qualified mechanic. Replacing a Headlight Bulb Your car has two bulbs on each side, four in total. Make sure you are replacing the bulb that is burned out. Your car uses halogen headlight bulbs.
Main Menu Table of Contents Lights Replacing Front Turn Signal and Side Marker Light Bulbs 5. Remove the burned out bulb from the socket by pushing it in and turning counterclockwise until it unlocks. HOLDING CLIP 6. Install the new bulb in the socket. Turn it clockwise to lock it in place. 7. Insert the socket back into the headlight assembly. Turn it clockwise to lock it in place. 8. Test the lights to make sure the new bulb is working. 1.
Main Menu Table of Contents Lights Replacing a Parking Light Bulb 3. Put the bulb holder back into its hole in the lens, and turn it clockwise until it locks. 4. Turn on the parking lights to make sure the new bulb works. 1. The parking light bulb is under the headlight bulb. Turn the bulb holder one-quarter turn counterclockwise to remove it from the lens. 2. Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms.
Main Menu Table of Contents Lights Replacing Rear Bulbs (in Fenders) 4. Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms. 5. Reinstall the socket into the light assembly by turning it clockwise until it locks. 6. Test the lights to make sure the new bulb is working. FASTENER 1. Open the trunk. Remove the fastener from the side of the trunk lining by turning it counterclockwise with a coin. Pull the lining back. 2.
Main Menu Table of Contents Lights Replacing Rear Bulbs (in Trunk Lid) 5. Install the new bulb in the socket. 6. Reinstall the socket into the light assembly. 7. Test the lights to make sure the new bulb is working. 1. Open the trunk. 2. Determine which of the two bulbs is burned out: taillight or back-up light. Maintenance 3. Remove the socket by turning it one-quarter turn counterclockwise. 4. Remove the burned out bulb from the socket by pulling it straight out of its socket.
Main Menu Table of Contents Lights Replacing a High-mount Brake Light Bulb Replacing a Rear License Bulb BULB 1. Open the trunk and remove the socket from the light assembly by turning it one-quarter turn counterclockwise. 1. Remove the license light assembly by carefully prying on the left edge of the lens with a flat-tip screwdriver and pulling the assembly out. 2. Remove the lens from the bulb holder by pulling the lens while squeezing the tabs on both sides of the holder. 2.
Main Menu Table of Contents Lights 3. Pull the bulb straight out of its socket. Push the new bulb in until it bottoms in the socket. 4. Turn on the parking lights and check that the new bulb is working. 5. Put the lens back on the bulb holder and push it until it latches. 6. Slide the left side of the light assembly into the hole. Push on the right side to latch the assembly into place.
Main Menu Table of Contents Lights On all models except DX model SPOTLIGHT On all models except DX model DOOR LIGHT On all models except DX model SUN VISOR Maintenance
Main Menu Table of Contents Lights Replacing the Trunk Light Bulb TRUNK LIGHT 1. Open the trunk. Pull down the trunk light cover. 2. Remove the bulb by pulling it straight out of its metal tabs. 3. Push the new bulb into the metal tabs. 4. Push the cover back in place.
Main Menu Table of Contents Storing Your Car If you need to park your car for an extended period (more than one month), there are several things you should do to prepare it for storage. Proper preparation helps prevent deterioration and makes it easier to get your car back on the road. If possible, store your car indoors. Fill the fuel tank. Change the engine oil and filter (see page 235). Wash and dry the exterior completely. Clean the interior. Make sure the carpeting, floor mats, etc.
Main Menu 286
Main Menu Appearance Care Regular cleaning and polishing of your Honda helps to keep it "new" looking. This section gives you hints on how to clean your car and preserve its appearance: the paint, brightwork, wheels and interior. Also included are several things you can do to help prevent corrosion. Exterior Care.................................. 288 Washing...................................... 288 Waxing........................................ 289 Aluminum Wheels.....................289 Paint Touch-up..
Main Menu Table of Contents Exterior Care Washing Frequent washing helps preserve your car's beauty. Dirt and grit can scratch the paint, while tree sap and bird droppings can permanently ruin the finish. Wash your car in a shady area, not in direct sunlight. If the car is parked in the sun, move it into the shade and let the exterior cool down before you start. Only use the solvents and cleaners recommended in this Owner's Manual.
Main Menu Table of Contents Exterior Care Waxing Always wash and dry the whole car before waxing it. You should wax your car, including the metal trim, whenever water sits on the surface in large patches. It should form into beads or droplets after waxing. You should use a quality liquid or paste wax. Apply it according to the instructions on the container. In general, there are two types of products: Waxes — A wax coats the finish and protects it from damage by exposure to sunlight, air pollution, etc.
Main Menu Table of Contents Interior Care Carpeting Vacuum the carpeting frequently to remove dirt. Ground-in dirt will make the carpet wear out faster. Periodically shampoo the carpet to keep it looking new. Use one of the foam-type carpet cleaners on the market. Follow the instructions that come with the cleaner, applying it with a sponge or soft brush. Keep the carpeting as dry as possible by not adding water to the foam.
Main Menu Table of Contents Interior Care Fabric Vacuum dirt and dust out of the material frequently. For general cleaning, use a solution of mild soap and lukewarm water, letting it air dry. To clean off stubborn spots, use a commercially-available fabric cleaner. Test it on a hidden area of the fabric first, to make sure it does not bleach or stain the fabric. Follow the instructions that come with the cleaner. Vinyl Remove dirt and dust with a vacuum cleaner.
Main Menu Table of Contents Interior Care Seat Belts LOOP If your seat belts get dirty, you can use a soft brush with a mixture of mild soap and warm water to clean them. Do not use bleach, dye, or cleaning solvents. They can weaken the belt material. Let the belts airdry before you use the car. Appearance Care Dirt build-up in the loops of the seat belt anchors can cause the belts to retract slowly.
Main Menu Table of Contents Corrosion Protection Two factors normally contribute to causing corrosion in your car: 1. Moisture trapped in body cavities. Dirt and road salt that collects in hollows on the underside of the car stays damp, promoting corrosion in that area. 2. Removal of paint and protective coatings from the exterior and underside of the car. Many corrosion-preventive measures are built into your Honda.
Main Menu Table of Contents Body Repairs Body repairs can affect your car's resistance to corrosion. If your car needs repairs after a collision, pay close attention to the parts used in the repair and the quality of the work. Make sure the repair facility uses Genuine Honda replacement body parts. Some companies make sheet metal pieces that seem to duplicate the original Honda body parts, but are actually inferior in fit, finish, and corrosion resistance.
Main Menu Taking Care of the Unexpected This section covers the morecommon problems that motorists experience with their vehicles. It gives you information about how to safely evaluate the problem and what to do to correct it. If the problem has stranded you on the side of the road, you may be able to get going again. If not, you will also find instructions on getting your car towed. Compact Spare Tire....................... 296 Changing a Flat Tire ..................... 297 If Your Engine Won't Start....
Main Menu Table of Contents Compact Spare Tire Your car has a compact spare tire that takes up less space. Use this spare tire as a temporary replacement only. Get your regular tire repaired or replaced and put back on your car as soon as you can. Check the inflation pressure of the compact spare tire every time you check the other tires. It should be inflated to: 60 psi (420 kPa , 4.
Main Menu Table of Contents Changing a Flat Tire If you have a flat tire while driving, TRUNK stop in a safe place to change it. Stopping in traffic or on the shoulder 03/07/10 16:11:09 31S5A930 0021 of a busy road is dangerous. Drive slowly along the shoulder until you get to an exit or an area to stop that is far away from the traffic lanes. The car can easily roll off the jack, seriously injuring anyone underneath.
Main Menu Table of Contents Changing a Flat Tire WHEEL NUTS JACK 6. The jack is behind a cover in the right fender. Remove the cover by turning the handle counterclockwise, then pulling on the cover. Taking Care of the Unexpected 7. Turn the jack's end bracket counterclockwise to loosen it, then remove the jack. 8. Loosen the four wheel nuts (4cylinder) or five (V-6) 1/2 turn with the wheel wrench.
Main Menu Table of Contents Changing a Flat Tire EXTENSION JACKING POINT 9. Locate the jacking point nearest the tire you need to change. It is pointed to by an arrow molded into the underside of the body. Place the jack under the jacking point. Turn the end bracket clockwise until the top of the jack contacts the jacking point. Make sure the jacking point tab is resting in the jack notch. WHEEL WRENCH 10.
Main Menu Table of Contents Changing a Flat Tire BRAKE HUB 12. Before mounting the spare tire, wipe any dirt off the mounting surface of the wheel and hub with a clean cloth. Wipe the hub carefully, it may be hot from driving. Taking Care of the Unexpected 13. Put on the spare tire. Put the wheel nuts back on finger-tight, then tighten them in a crisscross pattern with the wheel wrench until the wheel is firmly against the hub. Do not try to tighten them fully. 14.
Main Menu Table of Contents Changing a Flat Tire 4-cylinder model 15. Tighten the wheel nuts securely in the same crisscross pattern. Have the wheel nut torque checked at the nearest automotive service facility. Tighten the wheel nuts to: 80 lbf.ft (108N.m,11 kgf.m) 6-cylinder model 16. LX with ABS, EX, EX-V6 models Remove the center cap before storing the flat tire in the trunk well.
Main Menu Table of Contents Changing a Flat Tire, If Your Engine Won't Start WING BOLT 03/07/10 16:11:09 31S5A930 0021 20. Store the jack in its holder. Turn If Your Engine Won't Start SPACER the jack's end bracket to lock it in Diagnosing why your engine won't CONE place. Replace the cover. Store the tools. Loose items can fly around the interior in a crash and could seriously injure the occupants. 17. Place the flat tire face down in the spare tire well. 18.
Main Menu Table of Contents If Your Engine Won't Start Nothing Happens or the Starter Motor Operates Very Slowly When you turn the ignition switch to START (III), you do not hear the normal noise of the engine trying to start. You may hear a clicking sound or series of clicks, or nothing at all. Check these things: Your car has the Immobilizer System. You should use a properly-coded master or valet key to start the engine (see page 57).
Main Menu Table of Contents If Your Engine Won't Start, Jump Starting Jump Starting The Starter Operates Normally If your car's battery has run down, In this case, the starter motor's 03/07/10 16:11:09 31S5A930 you may be able to start the engine speed sounds normal, or even faster by using a booster battery. Although than normal, when you turn the this seems like a simple procedure, ignition switch to START (III), but you should take several precautions. the engine does not run.
Main Menu Table of Contents Jump Starting 4-cylinder models 3. Connect one jumper cable to the positive ( + ) terminal on your Honda's battery. Connect the other end to the positive ( + ) terminal on the booster battery. 6-cylinder models 4-cylinder models 4. Connect the second jumper cable to the negative (—) terminal on the booster battery. Connect the other end to the grounding strap as shown. Do not connect this jumper cable to any other part of the engine. 5.
Main Menu Table of Contents Jump Starting 6-cylinder models 4-cylinder models BOOSTER BATTERY 6. Start your car. If the starter motor still operates slowly, check the jumper cable connections to make sure they have good metal-tometal contact. 6-cylinder models BOOSTER BATTERY 7. Once your car is running, disconnect the negative cable from your car, then from the booster battery. Disconnect the positive cable from your car, then the booster battery.
Main Menu Table of Contents If Your Engine Overheats The pointer of your car's temperaYour car can overheat for several ture gauge should stay in the midreasons, such as lack of coolant or a range under most conditions. It may mechanical problem. The only go higher if you are driving up a long indication may be the temperature steep hill on a very hot day. If it gauge climbing to or above the red 03/07/10 16:11:09 31S5A930 climbs to the red mark, you should mark.
Main Menu Table of Contents If Your Engine Overheats 03/07/10 16:11:09 4. If the temperature gauge stays at the red mark, turn off the engine. 5. Wait until you see no more signs of steam or spray, then open the hood. 6. Look for any obvious coolant leaks, such as a split radiator hose. Everything is still extremely hot, so use caution. If you find a leak, it must be repaired before you continue driving (see Emergency Towing on page 320). 7.
Main Menu Table of Contents Low Oil Pressure Indicator LOW OIL PRESSURE INDICATOR NOTICE Running the engine with low oil pressure can cause serious mechanical damage almost immediately. Turn off the engine as soon as you can safely get the car stopped. 1. Safely pull off the road and shut off the engine. Turn on the hazard warning indicators. This indicator should light when the ignition switch is ON (II), and go out after the engine starts. It should never come on when the engine is running.
Main Menu Table of Contents Charging System Indicator Immediately turn off all electrical accessories: radio, heater, A/C, rear defogger, cruise control, etc. Try not to use other electrically-operated controls such as the power windows. Keep the engine running and take extra care not to stall it. Starting the engine will discharge the battery rapidly. CHARGING SYSTEM INDICATOR This indicator should come on when the ignition switch is ON (II), and go out after the engine starts.
Main Menu Table of Contents Malfunction Indicator Lamp MALFUNCTION INDICATOR LAMP (For L4- LEV) This indicator comes on for a few seconds when you turn the ignition switch ON (II). If it comes on at any other time, it indicates one of the engine's emissions control systems may have a problem. Even though you may feel no difference in your car's performance, it can reduce your fuel economy and cause your car to put out excessive emissions. Continued operation may cause serious damage.
Main Menu Table of Contents Malfunction Indicator Lamp Readiness Codes Your car has certain "readiness codes" that are part of the on-board diagnostics for the emissions systems. In some states, part of the emissions testing is to make sure these codes are set. If they are not set, the test cannot be completed. If your car's battery has been disconnected or gone dead, these codes are erased. It takes several days of driving under various conditions to set the codes again.
Main Menu Table of Contents Brake System Indicator BRAKE SYSTEM INDICATOR* *U.S. indicator shown The Brake System Indicator normally comes on when you turn the ignition switch ON (II). It is a reminder to check the parking brake. It comes on and stays lit if you do not fully release the parking brake. If it comes on at any other time, it indicates a problem with the car's brake system. In most cases, the problem is a low fluid level in the brake fluid reservoir.
Main Menu Table of Contents Closing the Moonroof If the electric motor will not close the moonroof, do the following: ROUND PLUG SOCKET 1. Check the fuse for the moonroof motor (see page 315). If the fuse is blown, replace it with one of the same or lower rating. 2. Try closing the moonroof. If the new fuse blows immediately or the moonroof motor still does not operate, you can close the moonroof manually. 3. Get the moonroof wrench out of the tool kit in the trunk. 4.
Main Menu Table of Contents Fuses All the electrical circuits in your car have fuses to protect them from a short circuit or overload. These fuses are located in three fuse boxes. INTERIOR The interior fuse boxes are located on each side of the dashboard. To open an interior fuse box, open the car door. Pull the cover open, then take it out of its hinges by pulling it toward you. UNDER-HOOD TAB The under-hood fuse box is located in the back of the engine compartment on the passenger's side.
Main Menu Table of Contents Fuses Checking and Replacing Fuses If something electrical in your car stops working, the first thing you should check for is a blown fuse. Determine from the chart on pages 318 and 319, or the diagram on the fuse box lid, which fuse or fuses control that component. Check those fuses first, but check all the fuses before deciding that a blown fuse is not the cause. Replace any blown fuses and check the component's operation. 1. Turn the ignition switch to LOCK (0).
Main Menu Table of Contents Fuses BLOWN 5. Look for a burned wire inside the fuse. If it is burned, replace it with one of the spare fuses of the same rating or lower. If you cannot drive the car without fixing the problem, and you do not have a spare fuse, take a fuse of the same rating or a lower rating from one of the other circuits. Make sure you can do without that circuit temporarily (such as the cigarette lighter or radio).
Main Menu Table of Contents Fuses UNDER-HOOD FUSE BOX Taking Care of the Unexpected
Main Menu Table of Contents Fuses INTERIOR FUSE BOXES DRIVER'S SIDE PASSENGER'S SIDE * : On Canadian models * : On Canadian models Taking Care of the Unexpected
Main Menu Table of Contents Emergency Towing If your car needs to be towed, call a professional towing service or, if you belong to one, an organization that provides roadside assistance. Never tow your car behind another vehicle with just a rope or chain. It is very dangerous. There are three popular types of professional towing equipment. Flat-bed Equipment The operator loads your car on the back of a truck. This is the best way to transport your Honda.
Main Menu Table of Contents Emergency Towing If you decide to tow your car with all four wheels on the ground, make sure you use a properly-designed and attached tow bar. Prepare the car for towing as described above, and leave the ignition switch in Accessory (I) so the steering wheel does not lock. Make sure the radio and any items plugged into the accessory power socket are turned off so they do not run down the battery. NOTICE Trying to lift or tow your car by the bumpers will cause serious damage.
Main Menu 322
Main Menu Technical Information The diagrams in this section give you the dimensions and capacities of your Honda, and the locations of the identification numbers. It also includes information you should know about your vehicle's tires and emissions control systems. Identification Numbers................. 324 Specifications................................. 326 DOT Tire Quality Grading........... 329 Treadwear.................................. 329 Traction.......................................
Main Menu Table of Contents Identification Numbers Your car has several identifying numbers located in various places. VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is the 17-digit number your Honda dealer uses to register your car for warranty purposes. It is also necessary for licensing and insuring your car. The easiest place to find the VIN is on a plate fastened to the top of the dashboard. You can see it by looking through the windshield on the driver's side.
Main Menu Table of Contents Identification Numbers The Engine Number is stamped into the engine block. It is on the front. 4-cylinder Models AUTOMATIC TRANSMISSION NUMBER 6-cylinder Models ENGINE NUMBER The Transmission Number is on a label on top of the transmission.
Main Menu Table of Contents Specifications * : 6-cylinder models * : 6-cylinder models the coolant in the reserve tank and that remaining in the *1 : Including engine. Reserve tank capacity: 0.16 US gal (0.6 , 0.13 Imp gal) the oil remaining in the engine.
Main Menu Table of Contents Specifications pages 257 *21 *3 * 259 DX LX, EX 6-cylinder models page 321 page 320 CONTINUED Technical Information
Main Menu Table of Contents Specifications DX *21 :: LX, EX *3: 4-cylinder models * *4 : 6-cylinder models Technical Information
Main Menu Table of Contents DOT Tire Quality Grading (U.S. Vehicles) The tires on your car meet all U.S. Federal Safety Requirements. All tires are also graded for treadwear, traction, and temperature performance according to Department of Transportation (DOT) standards. The following explains these gradings. Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between the tread shoulder and the maximum section width.
Main Menu Table of Contents DOT Tire Quality Grading (U.S. Vehicles) Temperature The temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Main Menu Table of Contents Oxygenated Fuels Some conventional gasolines are being blended with alcohol or an ether compound. These gasolines are collectively referred to as oxygenated fuels. To meet clean air standards, some areas of the United States and Canada use oxygenated fuels to help reduce emissions. The following are the U.S. EPA and Canadian CGSB approved percentages of oxygenates: ETHANOL (ethyl or grain alcohol) You may use gasoline containing up to 10 percent ethanol by volume.
Main Menu Table of Contents Driving in Foreign Countries If you are planning to take your Honda outside the U.S. or Canada, contact the tourist bureaus in the areas you will be traveling in to find out about the availability of unleaded gasoline with the proper octane rating. If unleaded gasoline is not available, be aware that using leaded gasoline in your Honda will affect performance and fuel mileage, and damage its emissions controls. It will no longer comply with U.S.
Main Menu Table of Contents Emissions Controls The burning of gasoline in your car's engine produces several byproducts. Some of these are carbon monoxide (CO), oxides of nitrogen (NOx) and hydrocarbons (HC). Gasoline evaporating from the tank also produces hydrocarbons. Controlling the production of NOx, CO, and HC is important to the environment. Under certain conditions of sunlight and climate, NOx and HC react to form photochemical "smog.
Main Menu Table of Contents Emissions Controls Exhaust Emissions Controls The exhaust emissions controls include three systems: PGM-FI, Ignition Timing Control and Three Way Catalytic Converter. These three systems work together to control the engine's combustion and minimize the amount of HC, CO, and NOx that comes out the tailpipe. The exhaust emissions control systems are separate from the crankcase and evaporative emissions control systems.
Main Menu Table of Contents Three Way Catalytic Converter Keep the engine tuned-up. The three way catalytic converter contains precious metals that serve as catalysts, promoting chemical reactions to convert the exhaust gasses without affecting the metals. The catalytic converter is referred to as a three-way catalyst, since it acts on HC, CO, and NOx. A replacement unit must be an original Honda part or its equivalent.
Main Menu Table of Contents State Emissions Testing Testing of Readiness Codes If you take your vehicle for a state emissions test shortly after the battery has been disconnected or gone dead, it may not pass the test. This is because of certain "readiness codes" that must be set in the onboard diagnostics for the emissions systems. These codes are erased when the battery is disconnected, and set again only after several days of driving under a variety of conditions.
Main Menu Table of Contents State Emissions Testing Select a nearby lightly traveled major highway where you can maintain a speed of 50 to 60 mph (80 to 90 km/h) for at least 20 minutes. Drive on the highway in D4 (A/T) or 5th (M/T). Do not use the cruise control. When traffic allows, drive for 90 seconds without moving the accelerator pedal. (Vehicle speed may vary slightly; this is okay.
Main Menu 338
Main Menu Warranty and Customer Relations Customer Relations Information................................. 340 U.S. Zone Office Map.................... 341 Canada Zone Office Map.............. 342 Warranty Coverages..................... 343 Reporting Safety Defects (U.S. Vehicles)........................... 344 Authorized Manuals......................
Main Menu Table of Contents Customer Relations Information Honda dealership personnel are trained professionals. They should be able to answer all your questions. If you encounter a problem that your dealership does not solve to your satisfaction, please discuss it with the dealership's management. The Service Manager or General Manager can help. Almost all problems are solved in this way.
Main Menu Table of Contents U.S. Zone Office Map Mid-Atlantic Zone 902 Wind River Ln., Suite 200 Gaithersburg, Maryland 20878 (301) 990-2020 Western Zone P.O. Box 2260 700 Van Ness Avenue Torrance, California 90501- 1490 (310) 781-4565 Northwestern Zone P.O. Box 20186 12439 N.E. Airport Way Southeastern Zone P.O.
Main Menu Table of Contents Canada Zone Office Map CUSTOMER RELATIONS RELATIONS AVEC LA CLIENTELE Honda Canada Inc.
Main Menu Table of Contents Warranty Coverages U.S. Owners Your new Honda is covered by these warranties: New Car Limited Warranty — covers your new vehicle, except for the battery, emissions control systems and accessories, against defects in materials and workmanship. Emissions Control Systems Defects Warranty and Emissions Performance Warranty — these two warranties cover your vehicle's emissions control systems. Time, mileage, and coverage are conditional.
Main Menu Table of Contents Reporting Safety Defects (U.S. Vehicles) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying American Honda Motor Co., Inc.
Main Menu Table of Contents Authorized Manuals Purchasing Factory Authorized Manuals (U.S. only) The following publications covering the operation and servicing of your vehicle can be obtained from Helm Incorporated, either by filling out the attached form or, for credit card holders, calling the toll-free phone number on the form. For manuals prior to the year shown below, contact Helm Incorporated, P.O. Box 07280, Detroit, Michigan 48207, or call 1-800-782-4356. Valid only for sales within the U.S.
Main Menu Table of Contents Authorized Manuals Service Manual: This manual covers maintenance and recommended procedures for repair to engine and chassis components. It is written for the Journeyman mechanic, but is simple enough for most mechanically-inclined owners to understand. Electrical Troubleshooting Manual: This manual complements the Service Manual by providing in-depth troubleshooting information for each electrical circuit in your vehicle.
Main Menu Index Accessories and Modifications.... 186 Accessories................................. 186 Additional Safety Precaution.... 187 Modifications............................. 187 ACCESSORY (Ignition Key Position)........................................ 74 Accessory Power Socket.............. 106 Additives, Engine Oil..................... 234 Airbag (SRS) ...................................... 9 Air Cleaner Element...................... 253 Air Conditioning.............................
Main Menu Index Capacities Chart............................. 326 Carbon Monoxide Hazard.............. 49 Carrying Cargo.............................. 188 Cassette Player Care.............................................151 Operation........................... 130, 148 CAUTION, Explanation of............... ii CD Changer.......................... 133, 165 CD Player........................................ 142 Certification Label......................... 324 Chains...........................................
Main Menu Index Driving............................................ 191 Economy..................................... 185 In Bad Weather.......................... 209 In Foreign Countries................. 332 Economy, Fuel............................... 185 Emergencies on the Road............. 295 Battery, Jump Starting.............. 304 Brake System Indicator............ 313 Changing a Flat Tire................. 297 Charging System Indicator...... 310 Checking the Fuses...................
Main Menu Index Gas Mileage, Improving................ 185 Gasohol........................................... 331 Gasoline.......................................... 178 Gauge............................................ 58 Octane Requirement................. 178 Tank, Filling the......................... 178 Gas Station Procedures................. 178 Gauges Engine Coolant Temperature .... 59 Fuel................................................59 Speedometer................................ 58 Tachometer...
Main Menu Index Label, Certification........................ 324 Lane Change, Signaling.................. 64 Lap/Shoulder Belts......................... 40 Lights Bulb Replacement..................... 278 Indicator........................................ 53 Parking.......................................... 62 Turn Signal................................... 64 LOCK (Ignition Key Position)....... 73 Locks Anti-theft Steering Column........ 73 Fuel Fill Door............................. 178 Glove Box.........
Main Menu Index Parking Brake................................ 101 Parking Lights.................................. 63 Parking Over Things that Burn... 335 PGM-FI System.............................. 334 Polishing and Waxing................... 289 Pre-Drive Safety Checklist............. 11 Pregnancy, Using Seat Belts.......... 17 Protecting Adults............................. 12 Additional Safety Precautions.... 18 Advice for Pregnant Women...... 17 Protecting Children.........................
Main Menu Index Setting the Clock........................... 101 The 5-speed Manual Transmission.......................... 195 Shift Lever Position Indicator...... 197 Shift Lock Release......................... 200 Side Airbags..................................... 45 How Your Side Airbags Work.... 45 How The Side Airbag Indicator Light Works............................. 46 Side Marker Lights, Bulb Replacement............................... 279 Signaling Turns................................ 64 Snow Tires.
Main Menu Index Tires................................................ 267 Air Pressure............................... 268 Checking Wear.......................... 270 Compact Spare........................... 298 DOT Tire Quality Grading....... 331 Inflation....................................... 268 Inspection................................... 270 Replacing.................................... 271 Rotating....................................... 271 Snow............................................
Main Menu Index Wipers, Windshield Changing Blades........................ 263 Operation...................................... 64 Worn Tires..................................... 270 Wrecker, Emergency Towing....... 320 *: U.S.
Main Menu Service Information Summary Gasoline: Unleaded gasoline, pump octane number of 86 or higher. Fuel Tank Capacity: 17.12 US gal (64.8 l, 14.26 Imp gal) Recommended Engine Oil: API Premium grade 5W-20 detergent oil (see page 235 ). 5-speed Manual Transmission Fluid: Honda Manual Transmission Fluid preferred, or an API service SG, SH or SJ, SAE 10W-30 or 10W- 40 motor oil as a temporary replacement (see page 249). Capacity: 2.0 US qt (1.9 l,1.
Main Menu Audio System AM/FM/Cassette/CD Stereo Audio System Your Honda's audio system provides clear reception on both AM and FM bands, while the preset buttons allow you to easily select your favorite stations.
Main Menu Audio System Operating the Radio The ignition switch must be in ACCESSORY (I) or ON (II) to operate the audio system. Turn the system on by pushing the PWR/ VOL knob. Adjust the volume by turning the same knob. PWR/VOL KNOB PRESET BUTTONS TUNE KNOB The band and frequency that the radio was last tuned to is displayed. To change bands, press the AM or FM button. On the FM band, ST will be displayed if the station is broadcasting in stereo. Stereo reproduction on AM is not available.
Main Menu Audio System You can use any of four methods to find radio stations on the selected band: TUNE, SEEK, SCAN or the Preset buttons. TUNE — Use the TUNE knob to tune the radio to a desired frequency. Turn the knob clockwise to tune to a higher frequency, or counterclockwise to tune to a lower frequency. SEEK — The SEEK function searches the band for a station with a strong signal. To activate it, press either SEEK button or then release it.
Main Menu Audio System AUTO SELECT — If you are traveling far from home and can no longer receive the stations you preset, you can use the Auto Select feature to find stations in the local area. A. SEL INDICATOR To activate Auto Select, press the A. SEL button. A. SEL will flash in the display, and the system will go into scan mode for several seconds. It automatically scans both bands, looking for stations with strong signals.
Main Menu Audio System If you do not like the stations Auto Select has stored, you can store other frequencies in the preset buttons. Use the TUNE, SEEK, or SCAN function to find the desired frequencies, then store them in the selected preset buttons as described previously. TUNE KNOB Auto Select does not erase the frequencies that you preset previously. When you return home, turn off Auto Select by pressing the A. SEL button. The preset buttons will then select the frequencies you originally set.
Main Menu Audio System Adjusting the Sound Balance/Fader — These two controls adjust the strength of the sound coming from each speaker. The Balance control adjusts the sideto-side strength, while the Fader control adjusts the front-to-back strength. BASS/FADER CONTROL To adjust the fader, push on the BASS/FADER control knob to get it to pop out. Pull it out slightly farther, and adjust the front-to-back sound to your liking.
Main Menu Audio System Operating the CD Player You operate the CD player with the same controls used for the radio. CD SLOT SKIP BUTTONS With the system on, insert the disc into the CD slot. Push the disc in halfway, the drive will pull it in the rest of the way and begin to play. The number of the track that is playing is shown in the display. You can also play 3-inch (8-cm) discs without using an adapter ring. In all cases, play only standard round discs.
Main Menu Audio System If you turn the system off while a CD is playing, either with the PWR/VOL knob or by turning off the ignition, the disc will stay in the drive. When you turn the system back on, the CD will begin playing where it left off. Press the eject button to remove the disc from the drive. If you eject the disc, but do not remove it from the slot, the system will automatically reload the disc after 15 seconds and put the CD player in pause mode. To begin playing the disc, press the CD button.
Main Menu Audio System CD Player Error Indications If you see an error indication in the display while operating the CD player, find the cause in the chart to the right. If you cannot clear the error indication, take the vehicle to your Honda dealer.
Main Menu Audio System CD Changer Error Indications If you see an error indication in the display while operating the CD changer, find the cause in the chart to the right. If you cannot clear the error indication, take the vehicle to your Honda dealer.
Main Menu Audio System Operating the Cassette Player The cassette system features Dolby B* noise reduction, automatic sensing of chromium-dioxide (CrO2) tape, and autoreverse for continuous play. PLAY BUTTON FF BUTTON REW DOLBY BUTTON BUTTON Make sure the tape opening on the cassette is facing to the right, then insert the cassette most of the way into the slot. The system will pull it in the rest of the way, and begin to play.
Main Menu Audio System The tape direction indicator will light to show you which side of the cassette is playing. The indicates the side you inserted facing upward is now playing. If you want to play the other side, press the PROG button. If you turn the system off while a tape is playing, either with the PWR/ VOL knob or by turning off the ignition, the cassette will remain in the drive. When you turn the system back on, the tape will begin playing where it left off.
Main Menu Audio System SKIP — The SKIP function allows you to find the beginning of a song or passage. To skip to the beginning of a song or passage currently playing, push the button. You will see REW flashing in the display as the tape rewinds. To skip to the beginning of the next song, push the button. You will see FF flashing in the display as the tape fast forwards. When the system finds the beginning of a song or passage, it goes back to PLAY.