2001 Accord Coupe Online Reference Owner's Manual Use these links (and links throughout this manual) to navigate through this reference. For a printed owner's manual, click on authorized manuals or go to www.helminc.com. Contents Owner's Identification Form Introduction ......................................................................................................................................... i A Few Words About Safety..........................................................................
Main Menu Owner’s Identification This Owner’s Manual should be considered a permanent part of the car, and should remain with the car when it is sold. OWNER ADDRESS STREET CITY STATE/PROVINCE ZIP CODE/ POSTAL CODE This Owner’s Manual covers all models of the Accord Coupe. You may find descriptions of equipment and features that are not on your particular model. V. I. N. DELIVERY DATE (Date sold to original retail purchaser) DEALER NAME DEALER NO.
Main Menu Introduction Congratulations! Your selection of a 2001 Honda Accord was a wise investment. It will give you years of driving pleasure. One of the best ways to enhance the enjoyment of your new Honda is to read this manual. In it, you will learn how to operate its driving controls and convenience items. Afterwards, keep this owner’s manual in your car so you can refer to it at any time. As you read this manual, you will find information that is preceded by a symbol.
Main Menu A Few Words About Safety Your safety, and the safety of others, is very important. And operating this car safely is an important responsibility. To help you make informed decisions about safety, we have provided operating procedures and other information on labels and in this manual. This information alerts you to potential hazards that could hurt you or others. Of course, it is not practical or possible to warn you about all the hazards associated with operating or maintaining your car.
Main Menu Your Car at a Glance POWER DOOR LOCKS (P.81) MIRROR CONTROLS (P.106) INSTRUMENT PANEL (P.57) DIGITAL CLOCK (P.109) HEATING/COOLING CONTROLS (P.118) CLIMATE CONTROL SYSTEM (P.125) AUDIO SYSTEM (P.133, 148) POWER WINDOW SWITCHES (P.103) FUEL FILL DOOR/TRUNK RELEASE HANDLE (P.175/86) 2 HOOD RELEASE HANDLE (P.176) AUTOMATIC TRANSMISSION (P.192) MANUAL TRANSMISSION (P.
Main Menu Your Car at a Glance INSTRUMENT PANEL BRIGHTNESS (P. 69) WINDSHIELD WIPERS/WASHERS (P. 70, 71) REAR WINDOW DEFOGGER (P. 72) MOONROOF SWITCH (P. 105) TRACTION CONTROL SYSTEM ON/OFF SWITCH (on V6 models) (P. 202) CRUISE CONTROL (P. 74) HAZARD WARNING LIGHTS (P. 71) TILT ADJUSTMENT (P. 73) HEADLIGHTS/TURN SIGNALS (P. 67, 69) HORN (P. 66) REMOTE AUDIO CONTROLS (P. 170) (on EX and EX-V6 models) CRUISE CONTROL (P.
Main Menu 4
Main Menu Driver and Passenger Safety This section gives you important information about how to protect yourself and your passengers. It shows you how to use seat belts properly. It explains your Supplemental Restraint System. And it tells you how to properly restrain infants and children in your car. Important Safety Precautions .......... 6 Your Car’s Safety Features .............. 7 Seat Belts ........................................ 8 Airbags ............................................
Main Menu Table of Contents Important Safety Precautions You’ll find many safety recommendations throughout this section, and throughout this manual. The recommendations on this page are the ones we consider to be the most important. Always Wear Your Seat Belt A seat belt is your best protection in all types of collisions. Airbags supplement seat belts, but airbags are designed to inflate only in a moderate to severe frontal collision.
Main Menu Table of Contents Your Car’s Safety Features (8) (10) (1) (3) Your car is equipped with many features that work together to protect you and your passengers during a crash. (4) (7) (9) (6) (7) (5) (2) *If equipped (2) (8) (1) Safety Cage (2) Crush Zones (3) Seats & Seat-Backs (4) Head Restraints (5) Collapsible Steering Column (6) Seat Belts (7) Front Airbags (8) Side Airbags* (9) Seat Belt Tensioners (10) Door Locks Some safety features do not require any action on your part.
Main Menu Table of Contents Your Car’s Safety Features These safety features are designed to reduce the severity of injuries in a crash. However, you and your passengers can’t take full advantage of these safety features unless you remain sitting in a proper position and always wear your seat belts properly. In fact, some safety features can contribute to injuries if they are not used properly.
Main Menu Table of Contents Your Car’s Safety Features Help keep you from being thrown against the inside of the vehicle and against other occupants. Airbags Keep you from being thrown out of the vehicle. Help keep you in a good position should the airbags ever deploy. A good position reduces the risk of injury from an inflating airbag, and allows you to get the best advantage from the airbag. Of course, seat belts cannot completely protect you in every crash.
Main Menu Table of Contents Your Car’s Safety Features The most important things you need to know about your airbags are: Airbags do not replace seat belts. They are designed to supplement the seat belts. Airbags offer no protection in rear impacts, rollovers, or minor frontal or side collisions. Airbags can pose serious hazards. To do their job, airbags must inflate with tremendous force and speed.
Main Menu Table of Contents Your Car’s Safety Features Pre-Drive Safety Checklist To make sure you and your passengers get the maximum protection from your car’s safety features, check the following each time before you drive away: All adults, and children who have outgrown child safety seats, are wearing their seat belts and wearing them properly (see page 15 ). Any infant or small child is properly restrained in a child seat in the back seat (see page 20 ).
Main Menu Table of Contents Protecting Adults Introduction The following pages provide instructions on how to properly protect the driver and other adult occupants. These instructions also apply to children who have outgrown child seats and are large enough to wear lap/shoulder belts. (See page 36 for important additional guidelines on how to properly protect larger children.) 1.Close and Lock the Doors After everyone has entered the car, be sure the doors are closed and locked.
Main Menu Table of Contents Protecting Adults 2.Adjust the Front Seats Any driver who sits too close to the steering wheel is at risk of being seriously injured or killed by striking the steering wheel or from being struck by an inflating front airbag during a crash. To reduce the chance of injury, wear your seat belt properly, sit upright with your back against the seat, and move the seat as far back as possible from the steering wheel while still maintaining full control of the car.
Main Menu Table of Contents Protecting Adults 3.Adjust the Seat-Backs Adjust the driver’s seat-back to a comfortable, upright position, leaving ample space between your chest and the airbag cover in the center of the steering wheel. If you sit too close to the steering wheel, you could be injured if the front airbag inflates. 14 Driver and Passenger Safety A front passenger should also adjust the seat-back to an upright position, but as far from the dashboard as possible.
Main Menu Table of Contents Protecting Adults 4.Adjust the Head Restraints Improperly positioning head restraints reduces their effectiveness and you can be seriously injured in a crash. Make sure head restraints are in place and positioned properly before driving. Before driving, make sure everyone with an adjustable head restraint has properly positioned the head restraint. The restraint should be positioned so the back of the occupant’s head rests against the center of the restraint.
Main Menu Table of Contents Protecting Adults If necessary, pull up on the belt again to remove any slack from the shoulder part, then check that the belt rests across the center of your chest and over your shoulder. This spreads the forces of a crash over the strongest bones in your upper body. Never place the shoulder portion of a lap/shoulder belt under your arm or behind your back. This could cause very serious injuries in a crash.
Main Menu Table of Contents Protecting Adults 6.Adjust the Steering Wheel Adjust the steering wheel, if needed, so that the wheel points toward your chest, not toward your face. Pointing the steering wheel toward your chest provides optimal protection from the airbag. 7.
Main Menu Table of Contents Protecting Adults Remember, to get the best protection from your car’s airbags and other safety features, you must sit properly and wear your seat belt properly. Advice for Pregnant Women Pregnant women should also sit upright and as far back as possible from the steering wheel or dashboard. This will reduce the risk of injuries to both the mother and her unborn child that can be caused by a crash or an inflating airbag.
Main Menu Table of Contents Protecting Adults Additional Safety Precautions Two people should never use the same seat belt. If they do, they could be very seriously injured in a crash. Do not put any accessories on seat belts. Devices intended to improve occupant comfort or reposition the shoulder part of a seat belt can severely compromise the protective capability of the seat belt and increase the chance of serious injury in a crash.
Main Menu Table of Contents Protecting Children Children who are unrestrained or improperly restrained can be seriously injured or killed in a crash. Any child too small for a seat belt should be properly restrained in a child seat. A larger child should be properly restrained with a seat belt. Children depend on adults to protect them. However, despite their best intentions, many parents and other adults may not know how to properly protect young passengers.
Main Menu Table of Contents Protecting Children Any child who is too small to wear a seat belt should be properly restrained in a child seat. (See page 25 .) A larger child should always be restrained with a seat belt. (See page 36 .) Children Should Sit in the Back Seat According to accident statistics, children of all ages and sizes are safer when they are restrained in the back seat, not the front seat.
Main Menu Table of Contents Protecting Children Infants Never put a rear-facing child seat in the front seat of a vehicle equipped with a passenger’s front airbag. If the airbag inflates, it can hit the back of the child seat with enough force to kill or very seriously injure an infant. 22 Driver and Passenger Safety Small Children Placing a forward-facing child seat in the front seat of a vehicle equipped with a passenger’s front airbag can be hazardous.
Main Menu Table of Contents Protecting Children U.S. Models Canadian Models To remind you of the passenger’s front airbag hazards, and that children must be properly restrained in the back seat, your car has warning labels on the dashboard and on the driver’s and front passenger’s visors. Please read and follow the instructions on these labels. To remind you of the front airbag hazards, your car has warning labels on the driver’s and front passenger’s visors.
Main Menu Table of Contents Protecting Children If You Must Drive with Several Children Your car has three seating positions in the back seat where children can be properly restrained. If you ever have to carry more than three children in your car: Place the largest child in the front seat, provided the child is large enough to wear a seat belt properly (see page 36 ). Move the vehicle seat as far to the rear as possible (see page 13 ). Have the child sit upright and well back in the seat (see page 17 ).
Main Menu Table of Contents Protecting Children Lock both doors and the trunk when your vehicle is not in use. Children who play in cars can accidentally get trapped inside the trunk. Teach your children not to play in or around cars. Know how to operate the emergency trunk opener (U.S. models only) and decide if your children should be shown how to use this feature (see page 87 ). Keep car keys and remote transmitters out of the reach of children.
Main Menu Table of Contents Protecting Children 3. The child seat should fit the vehicle seating position (or positions) where it will be used. Due to variations in the design of child seats, vehicle seats, and seat belts, all child seats will not fit all vehicle seating positions. Small Children: A child who is too large for a rear-facing child seat, and who can sit up without support, should be restrained in a forwardfacing child seat.
Main Menu Table of Contents Protecting Children Placing a Child Seat This page briefly summarizes Honda’s recommendations on where to place rear-facing and forwardfacing child seats in your car. Airbags Pose Serious Risks to Children The passenger’s front airbag inflates with enough force to kill or seriously injure an infant in a rear-facing child seat. A small child in a forward-facing child seat is also at risk.
Main Menu Table of Contents Protecting Children Installing a Child Seat After selecting a proper child seat, and a good position to install the seat, there are three main steps in installing the seat: 1. Secure the child seat to the car with a seat belt. All child seats must be secured to the car with the lap part of a lap/shoulder belt. A child whose seat is not properly secured to the car can be endangered in a crash. See pages 30 and 34 for instructions on how to secure child seats in this car. 2.
Main Menu Table of Contents Protecting Children Protecting Infants Rear-Facing Child Seat Placement Placing a rear-facing child seat in the front seat can result in serious injury or death if the passenger’s front airbag inflates. Always place a rear-facing child seat in the back seat, not the front. Child Seat Type Only a rear-facing child seat provides proper support for a baby’s head, neck, and back. Infants up to about one year of age must be restrained in a rear-facing child seat.
Main Menu Table of Contents Protecting Children Rear-Facing Child Seat Installation The lap/shoulder belts in the back seats have a locking mechanism that must be activated to secure a child seat. The following pages provide instructions and tips on how to secure a rear-facing child seat with this type of seat belt. 1. With the child seat in the desired back seating position, route the belt through the child seat according to the seat maker’s instructions, then insert the latch plate into the buckle.
Main Menu Table of Contents Protecting Children To deactivate the locking mechanism and remove a child seat, unlatch the buckle, unroute the seat belt, and let the belt fully retract. 4. After confirming that the belt is locked, grab the shoulder part of the belt near the buckle and pull up to remove any slack from the lap part of the belt. Remember, if the lap part of the belt is not tight, the child seat will not be secure.
Main Menu Table of Contents Protecting Children Rear-Facing Child Seat Installation Tips For proper protection, an infant must ride in a reclined, or semi-reclined position. To determine the proper reclining angle, check with the baby’s doctor or follow the seat maker’s recommendations. To achieve the desired reclining angle, it may help to put a rolled up towel under the toe of the child seat, as shown.
Main Menu Table of Contents Protecting Children Protecting Small Children We also recommend that a small child stay in the child seat as long as possible, until the child reaches the weight or height limit for the seat. Child Seat Placement In this car, the best place to install a forward-facing child seat is in one of the seating positions in the back seat. Placing a forward-facing child seat in the front seat of a vehicle equipped with a passenger’s front airbag can be hazardous.
Main Menu Table of Contents Protecting Children Child Seat Installation The lap/shoulder belts in the back and front passenger seating positions have a locking mechanism that must be activated to secure a child seat. The following pages provide instructions on how to secure a forward-facing child seat with this type of seat belt. 1.
Main Menu Table of Contents Protecting Children To deactivate the locking mechanism in order to remove a child seat, unlatch the buckle, unroute the seat belt, and let the belt fully retract. 4. After confirming that the belt is locked, grab the shoulder part of the belt near the buckle and pull up to remove any slack from the lap part of the belt. Remember, if the lap part of the belt is not tight, the child seat will not be secure.
Main Menu Table of Contents Protecting Children Additional Precautions for Small Children Never hold a small child on your lap. If you are not wearing a seat belt in a crash, you could be thrown forward into the dashboard and crush the child. If you are wearing a seat belt, the child can be torn from your arms during a crash. For example, if your car crashes into a parked vehicle at 30 mph (48 km/h), a 30-lb (14 kg) child will become a 900-lb (410 kg) force, and you will not be able to hold on.
Main Menu Table of Contents Protecting Children Checking Seat Belt Fit However, if the belt touches or crosses the child’s neck, the child needs to use a booster seat. Do not let a child wear a seat belt across the neck. This could result in serious neck injuries during a crash. Do not let a child put the shoulder part of a seat belt behind the back or under the arm. This could cause To determine if a lap/shoulder belt properly fits a child, have the child put on the seat belt.
Main Menu Table of Contents Protecting Children Using a Booster Seat A child may continue using a booster seat until the tops of the ears are even with the top of the seat-back. A child of this height should be tall enough to use the lap/shoulder belt without a booster. When Can a Larger Child Sit in Front The National Highway Traffic Safety Administration and Transport Canada recommend that all children ages 12 and under be properly restrained in a back seat.
Main Menu Table of Contents Protecting Children Of course, children vary widely. And while age may be one indicator of when a child can safely ride in the front, there are other important factors you should consider. Physical Size Physically, a child must be large enough for the lap/shoulder belt to properly fit over the hips, chest, and shoulder (see pages 15 and 36 ). If the seat belt does not fit properly, the child should not sit in the front.
Main Menu Table of Contents Protecting Children Using Child Seats with Tethers COVER Your car has three tether anchorage points under the rear window for securing a tether-style child seat to the car. The tether anchorage points are located under plastic covers. Pivot the cover backward to access the anchorage point. Since a tether can provide additional security, we recommend using a tether whenever one is required or available.
Main Menu Table of Contents Additional Information About Your Seat Belts Seat Belt System Components Your seat belt system includes lap/ shoulder belts in all five seating positions. The front seat belts are also equipped with automatic seat belt tensioners. The seat belt system also includes a light on the instrument panel to remind you and your passengers to fasten your belts.
Main Menu Table of Contents Additional Information About Your Seat Belts All seat belts have an emergency locking retractor. In normal driving, the retractor lets you move freely in your seat while it keeps some tension on the belt. During a collision or sudden stop, the retractor automatically locks the belt to help restrain your body. The seat belts in all seating positions except the driver’s have an additional locking mechanism that must be activated to secure a child seat.
Main Menu Table of Contents Additional Information About Your Seat Belts Automatic Seat Belt Tensioners The tensioners are designed to activate primarily in frontal collisions. The tensioners are independent of the airbag system, so they can be activated during a collision that might not cause the airbags to deploy. In this case, the airbags would not be needed but the additional seat belt tension can be helpful.
Main Menu Table of Contents Additional Information About Your Seat Belts Seat Belt Maintenance For safety, you should check the condition of your seat belts regularly. Pull each belt out fully and look for frays, cuts, burns, and wear. Check that the latches work smoothly and that the lap/shoulder belts retract easily. Any belt not in good condition or not working properly will not provide good protection and should be replaced as soon as possible.
Main Menu Table of Contents Additional Information About Your Airbags SRS Components Your Supplemental Restraint System (SRS) includes: Two front airbags. The driver’s airbag is stored in the center of the steering wheel; the front passenger’s airbag is stored in the dashboard. Both are marked ‘‘SRS AIRBAG.’’ Automatic seat belt tensioners (see page 43 ). Sensors that can detect a moderate to severe frontal collision.
Main Menu Table of Contents Additional Information About Your Airbags After a crash, you may see what looks like smoke. This is actually powder from the airbag’s surface. Although the powder is not harmful, people with respiratory problems may experience some temporary discomfort. If this occurs, get out of the car as soon as it is safe to do so. During a frontal crash, your seat belts help restrain your lower body and torso.
Main Menu Table of Contents Additional Information About Your Airbags To get the best protection from the side airbags, front seat occupants should wear their seat belts and sit upright and well back in their seats. How Your Side Airbags Work Some models are equipped with side airbags for the driver and a front seat passenger. The airbags are stored in the outer edges of the front seat-backs, and both are marked ‘‘SIDE AIRBAG.
Main Menu Table of Contents Additional Information About Your Airbags How the SRS Indicator Light Works The SRS indicator light alerts you to a potential problem with your front airbags. This light will also alert you to a potential problem with your automatic seat belt tensioners (page 43 ). On models with side airbags, this light will also alert you to a potential problem with your side airbags or passenger’s side airbag automatic cutoff system (see page 49 ).
Main Menu Table of Contents Additional Information About Your Airbags How The Side Airbag Indicator Light Works Only on models equipped with side airbags This light alerts you that the passenger’s side airbag has been automatically shut off. To reduce the risk of injury from an inflating side airbag, your car has an automatic cutoff system for the passenger’s side airbag.
Main Menu Table of Contents Additional Information About Your Airbags Airbag Service Your front and side airbag systems (if equipped) are virtually maintenance-free, and there are no parts you can safely service. However, you must have your car serviced if: Your airbags ever inflate. Any airbag that has deployed must be replaced along with the control unit and other related parts. Do not try to remove or replace any airbag by yourself. This must be done by a Honda dealer or a knowledgeable body shop.
Main Menu Table of Contents Additional Information About Your Airbags Do not cover or replace front seatback covers without consulting a Honda dealer. Improperly replacing or covering front seatback covers can prevent your side airbags from inflating during a collision. See page 183 for further information and precautions relating to your airbags.
Main Menu Table of Contents Carbon Monoxide Hazard Your car’s exhaust contains carbon monoxide gas. You should have no problem with carbon monoxide entering the car in normal driving if you maintain your car properly. Have the exhaust system inspected for leaks whenever: The car is raised for an oil change. You notice a change in the sound of the exhaust. The car was in an accident that may have damaged the underside. 52 Driver and Passenger Safety Carbon monoxide gas is toxic.
Main Menu Table of Contents Safety Labels These labels are in the locations shown. They warn you of potential hazards that could cause serious injury. Read these labels carefully. SUN VISOR U.S. models Canadian models If a label comes off or becomes hard to read, contact your Honda dealer for a replacement. DASHBOARD U.S.
Main Menu 54
Main Menu Instruments and Controls This section gives information about the controls and displays that contribute to the daily operation of your Honda. All the essential controls are within easy reach. Control Locations ............................ 56 Indicator Lights................................ 57 Gauges .............................................. 63 Speedometer ................................ 63 Tachometer .................................. 63 Odometer ......................................
Main Menu Table of Contents Control Locations MIRROR CONTROLS (P.106) POWER DOOR LOCKS (P.81) POWER WINDOW SWITCHES (P.103) 56 FUEL FILL DOOR/TRUNK RELEASE HANDLE (P.175/86) Instruments and Controls DIGITAL CLOCK (P.109) HOOD RELEASE HANDLE (P.176) HEATING/COOLING CONTROLS (P.118) CLIMATE CONTROL SYSTEM (P.125) AUDIO SYSTEM (P.
Main Menu Table of Contents Indicator Lights HIGH BEAM INDICATOR (P. 62) CRUISE CONTROL INDICATOR (P. 62) IMMOBILIZER SYSTEM INDICATOR (P. 59) TRACTION CONTROL SYSTEM INDICATOR (P. 60) SUPPLEMENTAL RESTRAINT SYSTEM INDICATOR (P. 60) ANTI-LOCK BRAKE SYSTEM INDICATOR* (P. 59) PARKING BRAKE AND BRAKE SYSTEM INDICATOR* (P. 59) SIDE AIRBAG INDICATOR (P. 60) MAINTENANCE REQUIRED INDICATOR (P. 65) MALFUNCTION INDICATOR LAMP (P. 311) LOW OIL PRESSURE INDICATOR (P. 58, 309) CHARGING SYSTEM INDICATOR (P.
Main Menu Table of Contents Indicator Lights The instrument panel has many indicators to give you important information about your car. Seat Belt Reminder Light This indicator lights when you turn the ignition switch ON (II). It is a reminder to you and your passengers to protect yourselves by fastening the seat belts. A beeper also sounds if you have not fastened your seat belt. If you do not fasten your seat belt, the beeper will stop after a few seconds but the light stays on until you do.
Main Menu Table of Contents Indicator Lights U.S. Canada U.S. Canada Parking Brake and Brake System Indicator This light has two functions: Anti-lock Brake System (ABS) Indicator 1. This indicator comes on when you turn the ignition switch ON (II). It is a reminder to check the parking brake. Driving with the parking brake not fully released can damage the brakes and tires.
Main Menu Table of Contents Indicator Lights Traction Control System (TCS) Indicator On all V6 models This indicator has three functions: 1. It comes on as a reminder that you have turned off the Traction Control System. 2. It flashes when the TCS is regulating wheelspin. 3. If it comes on and stays on when the Traction Control System is on, it indicates that there is a problem in the TCS. This light also comes on when you turn the ignition ON (II) and goes off after the engine starts.
Main Menu Table of Contents Indicator Lights Door and Brake Lamp Monitor The appropriate light comes on in this display if the trunk or either door is not closed tightly. If a brake light does not work, the BRAKE LAMP indicator comes on when you push the brake pedal with the ignition switch ON (II). Turn Signal and Hazard Warning Indicators The left or right turn signal light blinks when you signal a lane change or turn.
Main Menu Table of Contents Indicator Lights High Beam Indicator This light comes on with the high beam headlights. See page 67 for information on the headlight controls. On Canadian models, this indicator comes on with reduced brightness when the Daytime Running Lights (DRL) are on (see page 68 ). Cruise Control Indicator This lights when you set the cruise control. See page 74 for information on operating the cruise control. Low Fuel Indicator This light comes on as a reminder that you must refuel soon.
Main Menu Table of Contents Gauges U.S. Model shown TACHOMETER MAINTENANCE REQUIRED INDICATOR SPEEDOMETER TRIP METER FUEL GAUGE TEMPERATURE GAUGE ODOMETER TRIP METER SELECT/RESET BUTTON Speedometer Canadian Models U.S. Models This shows your speed in kilometers per hour (km/h). The smaller inner numbers are the speed in miles per hour (mph). This shows your speed in miles per hour (mph). The smaller inner numbers are the speed in kilometers per hour (km/h).
Main Menu Table of Contents Gauges Trip Meter This meter shows the number of miles (U.S.) or kilometers (Canada) driven since you last reset it. There are two trip meters: Trip A and Trip B. Switch between these displays by pressing the Select/ Reset button repeatedly. Each trip meter works independently, so you can keep track of two different distances. To reset a trip meter, display it, and then press and hold the Select/Reset button until the number resets to ‘‘0.0’’.
Main Menu Table of Contents Gauges Maintenance Required Indicator MAINTENANCE REQUIRED INDICATOR This indicator reminds you that it is time to take your car in for scheduled maintenance. Refer to the Maintenance Schedules for Normal and Severe Driving Conditions on pages 220 .− 224 For the first 6,000 miles (9,600 km) after the Maintenance Required Indicator is reset, it will come on for two seconds when you turn the ignition switch ON (II).
Main Menu Table of Contents Controls Near the Steering Wheel The two levers on the steering column contain controls for driving features you use most often. The left lever controls the turn signals, headlights, and high beams. The right lever controls the windshield washers and wipers. The switches for the hazard warning lights and rear window defogger are located to the right of the steering column.
Main Menu Table of Contents Controls Near the Steering Wheel Headlights If you leave the lights on with the ignition switch in ACCESSORY (I) or LOCK (0), you will hear a reminder chime when you open the driver’s door. To flash the high beams, pull the turn signal lever back lightly, then release it. The high beams will come on and go off. The high beams will stay on for as long as you hold the lever back, no matter what position the headlight switch is in.
Main Menu Table of Contents Controls Near the Steering Wheel Automatic Lighting Off Feature On EX and EX-V6 models The Automatic Lighting Off feature turns off the headlights, parking lights, taillights, side marker lights, license plate lights and instrument panel lights within 15 seconds of removing the key from the ignition switch and closing the driver’s door. This feature activates if you leave the headlight switch in the ‘‘ ’’ or ‘‘ ’’ position, remove the key, open, then close the driver’s door.
Main Menu Table of Contents Controls Near the Steering Wheel Instrument Panel Brightness KNOB Turn the knob on the left side of the instrument panel to adjust the brightness of the instrument panel lights. Turn Signals To signal a lane change, push lightly on the turn signal lever in the proper direction and hold it. The lever will return to the center position as soon as you release it. TURN SIGNAL LEVER Signal a turn or lane change with this lever.
Main Menu Table of Contents Controls Near the Steering Wheel Windshield Wipers The right lever controls the windshield wipers and washers. The rotary switch at the end of the lever has three positions: INT: intermittent : low speed : high speed 70 Instruments and Controls In intermittent, the wipers operate every few seconds. The sweep interval will change slightly with speed; getting shorter as you drive faster. In low speed and high speed, the wipers run continuously.
Main Menu Table of Contents Controls Near the Steering Wheel To operate the wipers in mist mode, push the control lever down. The wipers run at high speed until you release the lever. This gives you a quick way to clear the windshield. Windshield Washers Hazard Warning To clean the windshield, pull back on the wiper control lever. The washers spray until you release the lever.
Main Menu Table of Contents Controls Near the Steering Wheel The defogger and antenna wires on the inside of the rear window can be accidentally damaged. When cleaning the glass, always wipe side to side. Rear Window Defogger LX, EX and LX-V6 models The rear window defogger will clear fog, frost, and thin ice from the window. Push the defogger button to turn it on and off. The light above the button lights to show the defogger is on.
Main Menu Table of Contents Controls Near the Steering Wheel 3. Push the lever up to lock the Steering Wheel Adjustment steering wheel in that position. See page 17 for important safety information about how to properly position the steering wheel. 4. Make sure you have securely locked the steering wheel in place by trying to move it up and down. Make any steering wheel adjustment before you start driving.
Main Menu Table of Contents Steering Wheel Controls Cruise Control Cruise control allows you to maintain a set speed above 25 mph (40 km/h) without keeping your foot on the accelerator pedal. It should be used for cruising on straight, open highways. It is not recommended for conditions such as city driving, winding roads, slippery roads, heavy rain, or bad weather. You should have full control of the car under those conditions. Improper use of the cruise control can lead to a crash.
Main Menu Table of Contents Steering Wheel Controls The cruise control may not hold the set speed when you are going up and down hills. If your speed increases going down a hill, use the brakes to slow down to the desired speed. This will cancel the cruise control. To resume the set speed, press the RESUME/accel button. The CRUISE CONTROL light on the instrument panel comes on. RESUME/accel CANCEL SET/decel 3. Press and release the SET/decel button on the steering wheel.
Main Menu Table of Contents Steering Wheel Controls You can decrease the set cruising speed in any of these ways: Press and hold the SET/decel button. The car will decelerate. Release the button when you reach the desired speed. To slow down in very small amounts, tap the SET/decel button repeatedly. Each time you do this, your car will slow down about 1 mph (1.6 km/h). Tap the brake or clutch pedal lightly with your foot. The CRUISE CONTROL light on the instrument panel will go out.
Main Menu Table of Contents Steering Wheel Controls, Keys and Locks When you push the CANCEL button, or tap the brake or clutch pedal, the CRUISE CONTROL light on the instrument panel will go out and the car will begin to slow down. You can use the accelerator pedal in the normal way. The system remembers the previously-set cruising speed. To return to that speed, accelerate to above 25 mph (40 km/h), then press and release the RESUME/accel button.
Main Menu Table of Contents Keys and Locks The valet key works only in the ignition and the door locks. You can keep the trunk, trunk release handle, rear seat trunk access and the glove box locked when you leave your car and the valet key at a parking facility. You should have received a key number plate with your keys. You will need this key number if you ever have to get a lost key replaced. Keep the plate stored in a safe place. If you need to replace a key, use only Honda-approved key blanks.
Main Menu Table of Contents Keys and Locks The system may not recognize your key’s coding if another immobilizer key or other metal object is near the ignition switch when you insert the key. To make sure the system recognizes the key code: Do not keep other immobilizer keys on the same key ring. Use a plastic or leather key fob, not metal. Keep other keys away from your car’s key and the ignition switch while trying to start the engine.
Main Menu Table of Contents Keys and Locks Ignition Switch The ignition switch is on the right side of the steering column. It has four positions: • LOCK (0) • ACCESSORY (I) • ON (II) • START (III) 80 Instruments and Controls LOCK (0) − You can insert or remove the key only in this position. To switch from ACCESSORY to LOCK, you must push the key in slightly as you turn it. If your car has an automatic transmission, the shift lever must also be in Park.
Main Menu Table of Contents Keys and Locks ACCESSORY (I) − In this position, you can operate the audio system and the accessory power socket. ON (II) − This is the normal key position when driving. All features and accessories on the car are usable. Several of the lights on the instrument panel come on as a test when you turn the ignition switch from ACCESSORY to ON. START (III) − Use this position only to start the engine. The switch returns to ON (II) when you let go of the key.
Main Menu Table of Contents Keys and Locks To lock the passenger’s door when getting out of the car, push the lock tab down and close the door. To lock the driver’s door, remove the key from the ignition switch and push the lock tab down or push the master switch down, then close the door. Both doors can be locked from the outside by using the key in either door. LOCK TAB Each door has a lock tab at the top of the door. When you push down the lock tab on the driver’s door, both doors lock.
Main Menu Table of Contents Keys and Locks LOCK BUTTON When you push the LOCK button a second time within 5 seconds after you have locked the doors, the horn will sound once to verify that the security system will be set. If you unlock the doors with the remote transmitter, but do not open either door within 30 seconds, the doors automatically relock and the security system sets. TRUNK RELEASE BUTTON When you push the UNLOCK button once, only the driver’s door unlocks.
Main Menu Table of Contents Keys and Locks Panic Mode Replacing the Battery Panic mode allows you to remotely activate your car’s security system to attract attention. When activated, the horn will sound, and the exterior lights will flash, for about 30 seconds. To activate panic mode, press and hold the PANIC button for about two seconds. When the remote transmitter’s battery begins to get weak, it may take several pushes on the button to lock or unlock the doors, and the LED will not light.
Main Menu Table of Contents Keys and Locks Transmitter Care Avoid severe shock to the transmitter, such as dropping or throwing it. Also, protect it from extreme hot or cold temperatures. BATTERY Remove the old battery and note the polarity. Make sure the polarity of the new battery is the same (+ side facing up), then insert it in the transmitter. Snap the two halves of the transmitter case back together. Clean the transmitter case with a soft cloth.
Main Menu Table of Contents Keys and Locks See page 184 for cargo loading and weight limit information. Keep the trunk lid closed at all times while driving to avoid damaging the lid, and to prevent exhaust gas from getting into the interior. See Carbon Monoxide Hazard on page 52 . Trunk TRUNK RELEASE HANDLE You can open the trunk in two or three ways: Pull the trunk release handle to the left of the driver’s seat. Use the master key to open the trunk lock. The valet key does not work in this lock.
Main Menu Table of Contents Keys and Locks Emergency Trunk Opener MASTER KEY Parents should decide if their children should be shown how to use this feature. For more information about child safety, see pages 24 and 25 . RELEASE LEVER To protect items in the trunk when you need to give the key to someone else: 1. Lock the trunk release handle with the master key. 2. Give the person the valet key. U.S.
Main Menu Table of Contents Keys and Locks Glove Box An open glove box can cause serious injury to your passenger in a crash, even if the passenger is wearing the seat belt. Always keep the glove box closed while driving. GLOVE BOX Open the glove box by squeezing the handle. Close it with a firm push. Lock or unlock the glove box with the master key. The glove box light comes on only when the instrument panel lights are on.
Main Menu Table of Contents HomeLink Universal Transmitter On EX-V6 model The HomeLink Universal Transmitter built into your car can be programmed to operate remotelycontrolled devices around your home, such as garage doors, lighting, or home security systems. It can replace up to three remote transmitters. Customer Assistance If you have problems with training the HomeLink Universal Transmitter, or would like information on home products that can be operated by the transmitter, call (800) 355-3515.
Main Menu Table of Contents HomeLink Universal Transmitter Training the Transmitter Before you can use the HomeLink Universal Transmitter to operate devices around your home, it must ‘‘learn’’ the proper codes. For example, to train the transmitter to open and close the garage door: Before you begin − If you just took delivery of your vehicle and have not trained any of the buttons in the HomeLink transmitter before, you should erase any previously learned codes before training the first button.
Main Menu Table of Contents HomeLink Universal Transmitter Canadian Owners: The remote control you are training from may stop transmitting after two seconds. This is not long enough for the HomeLink transmitter to learn the code. Release and press the button on the remote control every two seconds until the transmitter has learned the code. 5. The red light in the transmitter should begin flashing. It will flash slowly at first, then rapidly. 6. When the red light flashes rapidly, release both buttons.
Main Menu Table of Contents HomeLink Universal Transmitter It may be helpful to have someone assist you with this procedure. TRAINING BUTTON 1. Make sure you have properly completed the ‘‘Training the Transmitter’’ procedure. 5. Press and release the HomeLink transmitter button again. This should turn off the training light on the garage door opener unit. (Some systems may require you to press and release the button up to three times.) 2. Find the ‘‘Training’’ button on your garage door opener unit.
Main Menu Table of Contents HomeLink Universal Transmitter Retraining a Button To train an already programmed transmitter button to operate a new device: 1. Select the transmitter button you want to train. 2. Press and hold the transmitter button until the red light begins to flash slowly (approximately 20 seconds). 3. While continuing to hold the transmitter button, place the remote control for the device 2 to 5 inches from the HomeLink transmitter. 4. Press and hold the button on the remote control.
Main Menu Table of Contents Seat Adjustments Front Seat Adjustments See pages 13 − 14 for important safety information and warnings about how to properly position seats and seat-backs. Make all seat adjustments before you start driving. To adjust the seat forward and backward, pull up on the lever under the seat cushion’s front edge. Move the seat to the desired position and release the lever. Try to move the seat to make sure it is locked in position.
Main Menu Table of Contents Seat Adjustments Driver’s Seat Manual Height Adjustment Driver’s Seat Power Height Adjustment On LX model On EX model The height of your driver’s seat is adjustable. Turn the front dial on the outside of the seat cushion to raise the front of the seat bottom and turn the rear dial to raise the rear. The height of your driver’s seat is power adjustable. Pull up on the switch to raise the seat. Push it down to lower the seat. Make all adjustments before you start driving.
Main Menu Table of Contents Seat Adjustments Driver’s Seat Power Adjustments On all V6 models and the 4-cylinder EX model with leather interior See pages 13 − 14 for important safety information and warnings about how to properly position seats and seat-backs. The two power seat adjustment switches are on the outside edge of the seat bottom. The horizontal switch adjusts the seat bottom in several directions. The short vertical switch adjusts the seat-back angle.
Main Menu Table of Contents Seat Adjustments Driver’s Lumbar Support Pull the center of the horizontal switch up to raise the seat. Push it down to lower the seat. Adjust the seat-back angle by pushing the rear switch in the direction you want to move. On EX and EX-V6 models Vary the lumbar support by moving the lever on the right side of the seat-back. Move the lever forward or backward to adjust the lumbar support through its full range.
Main Menu Table of Contents Seat Adjustments Rear Seat Access Driver’s Side Passenger’s Side RELEASE LEVER On all V6 models and the 4-cylinder EX model with leather interior To get into the rear seat on the driver’s side, open the door and pull the release lever up on the side of the seat-back. The seat-back will tilt forward to allow easier entry to the rear seat.
Main Menu Table of Contents Seat Adjustments Head Restraints See page 15 for important safety information and a warning about how to properly position the head restraints. The front head restraints help protect you and your passenger from whiplash and other injuries. They are most effective when you adjust them so the back of the occupant’s head rests against the center of the restraint. A taller person should adjust the restraint as high as possible.
Main Menu Table of Contents Seat Adjustments Folding Rear Seat The back of the rear seat folds down to give you direct access to the trunk. Each side folds down separately. With only half the seat folded, you can still carry a passenger in the back seat. The seat-back can be released from inside the car or inside the trunk. GUIDE MASTER KEY To fold down either side of the seatback from inside the car, insert the master key in the lock on the rear shelf.
Main Menu Table of Contents Seat Adjustments Make sure all rear shoulder belts are positioned in front of the rear seatback whenever the seat-back is in its upright position. RELEASE To release the seat-back from inside the trunk, pull the release under the trunk panel. Push the seat-back down, then let go of the release. Make sure all items in the trunk, or items extending through the opening into the back seat, are secured. Loose items can fly forward and cause injury if you have to brake hard.
Main Menu Table of Contents Seat Heaters SEAT HEATERS The HI or LO indicator lights and remains lit until you turn it off by pushing the opposite side of the switch lightly. The indicator will turn off. In HI, the heater turns off when the seat gets warm, and turns back on after the seat’s temperature drops. It continues to cycle as long as you leave it set on HI. The HI indicator remains lit as a reminder that you have the heater on.
Main Menu Table of Contents Power Windows Your car’s windows are electricallypowered. Turn the ignition switch to ON (II) to raise or lower any window. MAIN SWITCH Closing a power window on someone’s hands or fingers can cause serious injury. Each door has a switch that controls its window. To open the window, push the switch down and hold it. Release the switch when you want the window to stop. Close the window by pulling back on the switch and holding it.
Main Menu Table of Contents Power Windows The master control panel also contains these extra features: AUTO − To open the driver’s window fully, push the window switch firmly down and release it. The window automatically goes all the way down. To stop the window from going all the way down, pull back on the window switch briefly. To open the driver’s window only partially, push the window switch down lightly and hold it. The window will stop as soon as you release the switch.
Main Menu Table of Contents Moonroof MOONROOF SWITCH To tilt up the back of the moonroof, press and hold the center button ( ). To close the moonroof, press and hold the top of the switch ( ). To open the moonroof, press and hold the bottom of the switch ( ). Release the switch when the moonroof gets to the desired position. Make sure everyone’s hands are away from the moonroof before opening or closing it.
Main Menu Table of Contents Mirrors Adjusting the Power Mirrors SELECTOR SWITCH TAB Keep the inside and outside mirrors clean and adjusted for best visibility. Be sure to adjust the mirrors before you start driving. The inside mirror has day and night positions. The night position reduces glare from headlights behind you. Flip the tab on the bottom edge of the mirror to select the day or night position.
Main Menu Table of Contents Mirrors 4. When you finish, move the selector switch to the center (off) position. This turns off the adjustment switch so you can’t move a mirror out of position by accidentally bumping the switch. HEATED MIRROR BUTTON Available on all Canadian models The outside mirrors are heated to remove fog and frost. With the ignition switch ON (II), turn on the heaters by pressing the button. The light in the button comes on as a reminder.
Main Menu Table of Contents Parking Brake Driving the car with the parking brake applied can damage the rear brakes and axles. PARKING BRAKE LEVER To apply the parking brake, pull the lever up fully. To release it, pull up slightly, push the button, and lower the lever. The parking brake light on the instrument panel should go out when the parking brake is fully released with the engine running (see page 59 ).
Main Menu Table of Contents Digital Clock, Sunglasses Holder 2. Press and hold the M button until the numbers advance to the desired time. Digital Clock You can use R to quickly set the time to the nearest hour. If the displayed time is before the half hour, pressing R sets the clock back to the previous hour. If the displayed time is after the half hour, pressing R sets the clock forward to the beginning of the next hour.
Main Menu Table of Contents Sunglasses Holder, Beverage Holder Beverage Holder INNER LINER Push Some larger styles of sunglasses may not fit in the holder. To open the beverage holder, push on the top. The beverage holder lid is spring-loaded and will swing open. To close it, push it down until it latches. The inner liner can be removed if you want to hold a larger cup. 110 Instruments and Controls Be careful when you are using the beverage holder.
Main Menu Table of Contents Console Compartment LEVER LEVER CONSOLE COMPARTMENT To open the console compartment, pull up on the lower lever and lift the lid. To close, lower the lid and push it down until it latches. COIN HOLDER On EX and EX-V6 models The console compartment has a Compact Disc holder. You can put small items in the tray located in the console compartment lid. To use the tray, pull up on the upper lever and lift up the armrest pad.
Main Menu Table of Contents Sun Visor, Vanity Mirror Sun Visor EXTENSION Make sure you put the sun visor back in place when you are getting into or out of the car. Do not use the sun visor extension over the rear view mirror. Vanity Mirror SUN VISOR To use the sun visor, pull it down. You can also use the sun visor at the side window. Remove the support rod from the clip and swing the sun visor toward the side window. In this position, the sun visor can be extended by sliding out the extension.
Main Menu Table of Contents Coin Box, Center Pocket, Accessory Power Socket Coin Box Center Pocket COIN BOX The coin box is located under the air vent. To open the coin box, pull the bottom edge. Close it with a firm push. Accessory Power Socket ACCESSORY POWER SOCKET On LX and LX-V6 models The center pocket is located under the audio system. To open the lid, pull it down. Close it with a firm push. To use the accessory power socket, pull out on the cover.
Main Menu Table of Contents Interior Lights Ceiling Light LX, LX-V6 Spotlights The light goes out when both doors are closed. OFF On EX and EX-V6 models ON DOOR ACTIVATED The ceiling light has a three-position switch. In the OFF position, the light does not come on. In the center position, the ceiling light comes on when you open either door. EX, EX-V6 After both doors are closed tightly, the light dims slightly, then fades out in about 10 seconds.
Main Menu Table of Contents Interior Lights Courtesy Lights IGNITION SWITCH LIGHT DOOR LIGHT The courtesy light in each door comes on when the door is opened, and goes out when the door is closed. Your car also has a courtesy light in the ignition switch. This light comes on when you open the driver’s door. It remains on for several seconds after the door is closed.
Main Menu 116
Main Menu Comfort and Convenience Features The heating and air conditioning systems in your Honda provide a comfortable driving environment in all weather conditions. The standard audio system has many features. This section describes those features and how to use them. (If you selected an optional audio system, refer to the operating instructions that came with it.) On EX and EX-V6 models Your Honda has an anti-theft audio system that requires a code number to enable it.
Main Menu Table of Contents Heating and Cooling On LX, LX-V6 and EX models Proper use of the Heating and Cooling system can make the interior dry and comfortable, and keep the windows clear for best visibility. FAN CONTROL DIAL MODE BUTTONS TEMPERATURE CONTROL DIAL What Each Control Does Fan Control Dial Turning this dial clockwise increases the fan’s speed, which increases air flow. Temperature Control Dial Turning this dial clockwise increases the temperature of the air flow.
Main Menu Table of Contents Heating and Cooling Mode Buttons Use the MODE buttons to select the vents the air flows from. Some air will flow from the dashboard corner vents in all modes. Air flows from the center and corner vents in the dashboard. Air flow is divided between the vents in the dashboard and the floor vents. Air flows from the floor vents. Air flow is divided between the floor vents and the defroster vents at the base of the windshield.
Main Menu Table of Contents Heating and Cooling Vent Controls CENTER VENT DRIVER’S-SIDE VENT PASSENGER’S-SIDE VENT Close Close Open Open The direction of air flow from the vents in the center and each side of the dashboard is adjustable. To adjust the air flow from the center vent, move the tab up-anddown and side-to-side. 120 Comfort and Convenience Features On the driver’s-side vent, move the vent up-and-down and move the tab side-to-side.
Main Menu Table of Contents Heating and Cooling How to Use the System This section covers how to set up the system controls for ventilation, heating, cooling, dehumidifying, and defrosting. FAN CONTROL DIAL The engine must be running for the heater and air conditioning to generate hot and cold air. The heater uses engine coolant to warm the air. If the engine is cold, it will be several minutes before you feel warm air coming from the system. MODE BUTTONS RECIRCULATION BUTTON clears.
Main Menu Table of Contents Heating and Cooling To Cool with A/C 1. Turn on the A/C by pressing the button. The light above the button comes on when a fan speed is selected. 2. Make sure the temperature control dial is all the way to the left. . 3. Select 4. If the outside air is humid, select Recirculation mode. If the outside air is dry, select Fresh Air mode. 5. Set the fan to the desired speed.
Main Menu Table of Contents Heating and Cooling To Heat To warm the interior: 1. Start the engine. and Fresh Air mode. 2. Select 3. Set the fan to the desired speed. 4. Adjust the warmth of the air with the temperature control dial. To Heat and Dehumidify with Air Conditioning Air conditioning, as it cools, removes moisture from the air. When used in combination with the heater, it makes the interior warm and dry. 1. Switch the fan on. 2. Turn on the air conditioning. and Fresh Air mode. 3. Select 4.
Main Menu Table of Contents Heating and Cooling To remove exterior frost or ice from the windshield and side windows after the car has been sitting out in cold weather: 1. Start the engine. . 2. Select When you select , the system automatically switches to Fresh Air mode and turns on the A/C. 3. Switch the fan and temperature controls to maximum. To rapidly remove exterior frost or ice from the windshield (on very cold days), first select the Recirculation mode.
Main Menu Table of Contents Climate Control System On EX-V6 model The automatic climate control system in your Honda picks the proper combination of air conditioning, heating, and ventilation to maintain the interior temperature you select. The system also adjusts the fan speed and air flow levels. CENTER VENTS DRIVER’S-SIDE VENT Close The direction of air flow from the vents in the center and each side of the dashboard is adjustable.
Main Menu Table of Contents Climate Control System PASSENGER’S-SIDE VENT Close Open The climate control system draws air through the exterior vents at the bottom of the windshield. Keep these vents clear of leaves and other debris. For the climate control system to provide heating and cooling, the engine must be running.
Main Menu Table of Contents Climate Control System Fully-automatic Operation To put the Automatic Climate Control in fully-automatic mode, press the AUTO button and set the fan control dial to AUTO, then set the desired temperature by turning the temperature control dial. You will see FULL AUTO in the system’s display. The light above the button also shows you which mode, Recirculation or Fresh Air, is selected.
Main Menu Table of Contents Climate Control System Semi-automatic Operation You can manually select various functions of the Climate Control system when it is in FULL AUTO. All other features remain automatically controlled. Making any manual selection causes the word FULL to go out. TEMPERATURE CONTROL DIAL AIR CONDITIONING BUTTON Air Conditioning (A/C) Button Press the A/C button to turn the air conditioning on and off. You will see A/C ON or A/C OFF in the display.
Main Menu Table of Contents Climate Control System Fan Control Dial You can manually select the fan speed by turning the fan control dial. When you turn the dial clockwise, the fan is taken out of automatic mode and starts to run at its lowest speed. Turning the dial fully clockwise increases the fan’s speed, which increases air flow. MODE BUTTON FAN CONTROL DIAL Mode Button Use the MODE button to select the vents the air flows from. Some air will flow from the dashboard corner vents in all modes.
Main Menu Table of Contents Climate Control System The main air flow is divided between the floor vents and defroster vents at the base of the windshield. The main air flow comes from the floor vents. The main air flow is divided between the dashboard vents and the floor vents. The main air flow comes from the dashboard vents.
Main Menu Table of Contents Climate Control System The button directs the main air flow to the windshield for faster defrosting. It also overrides any MODE selection you may have made. When you select , the A/C turns on automatically and the system selects Fresh Air mode. For faster defrosting, manually set the fan speed to high. You can also increase air flow to the windshield by closing the side vents in the dashboard.
Main Menu Table of Contents Climate Control System Sunlight Sensor/Temperature Sensor SUNLIGHT SENSOR The climate control system has two sensors. A sunlight sensor is located in the top of the dashboard and a temperature sensor is next to the steering column. Do not cover the sensors or spill any liquid on them.
Main Menu Table of Contents Audio System AM/FM/CD Audio System For LX and LX-V6 models Your Honda’s audio system provides clear reception on both AM and FM bands, while the preset buttons allow you to easily select your favorite stations.
Main Menu Table of Contents Audio System Operating the Radio The ignition switch must be in ACCESSORY (I) or ON (II) to operate the audio system. Turn the system on by pushing the PWR/ VOL knob or the AM/FM button. Adjust the volume by turning the PWR/VOL knob. The band and frequency that the radio was last tuned to is displayed. To change bands, press the AM/FM button. On the FM band, ST will be displayed if the station is broadcasting in stereo. Stereo reproduction on AM is not available.
Main Menu Table of Contents Audio System SCAN − The SCAN function samples all the stations with strong signals on the selected band. To activate it, press the SCAN button, then release it. When the system is in the SCAN mode, SCAN shows in the display. The system will scan up the band for a station with a strong signal. When it finds one, it will stop and play that station for approximately five seconds.
Main Menu Table of Contents Audio System Preset − You can store the frequencies of your favorite radio stations in the six preset buttons. Each button will store one frequency on the AM band, and two frequencies on the FM band. AM/FM BUTTON AUTO SELECT INDICATOR A. SEL BUTTON SCAN BUTTON To store a frequency: 1. Select the desired band, AM or FM. FM1 and FM2 let you store two frequencies with each Preset button. 2. Use the TUNE, SEEK, or SCAN function to tune the radio to a desired station. 3.
Main Menu Table of Contents Audio System Once a station’s frequency is stored, simply press and release the proper preset button to tune to it. The preset frequencies will be lost if your car’s battery goes dead, is disconnected, or the radio fuse is removed. AUTO SELECT − If you are traveling far from home and can no longer receive the stations you preset, you can use the Auto Select feature to find stations in the local area. To activate Auto Select, press the A. SEL button. A.
Main Menu Table of Contents Audio System Adjusting the Sound Bass, Treble, Balance, and Fader are each adjustable. You select which of these you want to adjust by pressing the TUNE knob. The mode changes from BAS to TRE to FAD to BAL, and then back to the selected audio mode, each time you press the TUNE knob. Each mode is shown in the display as it changes. Adjustment Level Treble/Bass − Use these modes to adjust the tone to your liking. Select TRE or BAS by pressing the TUNE knob.
Main Menu Table of Contents Audio System Balance/Fader − These two modes adjust the strength of the sound coming from each speaker. BAL adjusts the side-to-side strength, while FAD adjusts the front-to-back strength. Radio Frequencies and Reception For information, See page 154 . Audio System Lighting You can use the instrument panel brightness control knob to adjust the illumination of the audio system (see page 69 ).
Main Menu Table of Contents Audio System Operating the CD Player You operate the CD player with the same controls used for the radio. With the ignition switch in ACCESSORY (I) or ON (II), insert the disc into the CD slot. Push the disc in halfway, the drive will pull it in the rest of the way and begin to play. The number of the track that is playing is shown in the display.
Main Menu Table of Contents Audio System When the system reaches the end of the disc, it will return to the beginning and play that disc again. You can use the SEEK/SKIP bar while a disc is playing to select passages and change tracks. You can switch to the radio while a CD is playing by pressing the AM/ FM button. Press the CD button to return to playing the CD. The CD will begin playing where it left off. To move rapidly within a track, press and hold the SEEK/SKIP bar.
Main Menu Table of Contents Audio System Operating the CD Changer (Optional) A Compact Disc changer is available for your car. It holds up to six discs, providing several hours of continuous entertainment. You operate this CD changer with the same controls used for the in-dash CD player. Load the desired CDs in the magazine and load the magazine in the changer according to the instructions that came with the unit. Play only standard round discs. Oddshaped CDs may jam in the drive or cause other problems.
Main Menu Table of Contents Audio System CD Player Error Indications If you see an error indication in the display while operating the CD player, find the cause in the chart to the right. If you cannot clear the error indication, take the car to your Honda dealer. Indication Cause FOCUS Error Mechanical Error High temperature Solution Press the EJECT button and pull out the disc. Check if the disc is inserted correctly in the CD player. Make sure the disc is not scratched or damaged.
Main Menu Table of Contents Audio System CD Changer Error Indications If you see an error indication in the display while operating the CD changer, find the cause in the chart to the right. If you cannot clear the error indication, take the car to your Honda dealer. Indication Cause FOCUS Error Solution Press the magazine eject button and pull out the magazine, check for error indication. Insert the magazine again.
Main Menu Table of Contents Audio System Operating the Cassette Player (Optional) The cassette system features Dolby B* noise reduction, automatic sensing of chromium-dioxide (CrO2) tape, and autoreverse for continuous play. AM/FM BUTTON PWR/VOL KNOB TAPE DIRECTION INDICATOR REPEAT INDICATOR CD/TAPE BUTTON REPEAT BUTTON To operate the cassette player, the ignition switch must be in ACCESSORY(I) or ON(II).
Main Menu Table of Contents Audio System The tape direction indicator will light to show you which side of the cassette is playing. The ▲ indicates the side you inserted facing upward is now playing. If you want to play the other side, press the PLAY/ PROG button. Dolby B noise reduction turns on when you insert a cassette. The indicator will light in the display. If the tape was not recorded with Dolby B noise reduction, turn it off by pressing the NR button.
Main Menu Table of Contents Audio System SKIP − The Skip function allows you to find the beginning of a song or passage. To activate SKIP, press the SEEK/SKIP bar. Press the side to advance to the beginning of the next song or passage, or the side to return to the beginning of the current song or passage. FF or REW will flash in the display as the tape moves. When the system reaches the beginning of the next song or passage (FF), or the beginning of the current one (REW), it goes back to PLAY mode.
Main Menu Table of Contents Audio System AM/FM/Cassette/CD Changer Audio System PWR/VOL KNOB AM BUTTON TUNE KNOB For EX and EX-V6 models Your Honda’s audio system provides clear reception on both AM and FM bands, while the preset buttons allow you to easily select your favorite stations. FM BUTTON STEREO INDICATOR The cassette system features Dolby B* noise reduction, automatic sensing of chromium-dioxide (CrO2) tape, and autoreverse for continuous play.
Main Menu Table of Contents Audio System The anti-theft feature will disable the system if it is disconnected from the car’s battery. To get the system working again, you must enter a code number (see page 171 ). Operating the Radio The ignition switch must be in ACCESSORY (I) or ON (II) to operate the audio system. Turn the system on by pressing the PWR/ VOL knob or the AM or FM button. Adjust the volume by turning the knob. The band and frequency that the radio was last tuned to is displayed.
Main Menu Table of Contents Audio System SCAN − The SCAN function samples all the stations with strong signals on the selected band. To activate it, press the SCAN button, then release it. When the system is in the SCAN mode, SCAN shows in the display. The system will scan up the band for a station with a strong signal. When it finds one, it will stop and play that station for approximately five seconds.
Main Menu Table of Contents Audio System AUTO SELECT − If you are traveling far from home and can no longer receive the stations you preset, you can use the Auto Select feature to find stations in the local area. To activate Auto Select, press the A. SEL button. A. SEL will flash in the display, and the system will go into scan mode for several seconds. It automatically scans both bands, looking for stations with strong signals.
Main Menu Table of Contents Audio System If you do not like the stations Auto Select has stored, you can store other frequencies in the preset buttons. Use the TUNE, SEEK, or SCAN function to find the desired frequencies, then store them in the selected preset buttons as described previously. Auto Select does not erase the frequencies that you preset previously. When you return home, turn off Auto Select by pressing the A. SEL button. The preset buttons will then select the frequencies you originally set.
Main Menu Table of Contents Audio System Adjusting the Sound Bass, Treble, Balance, and Fader are each adjustable. You select which of these you want to adjust by pressing the TUNE knob. The mode changes from BAS to TRE to FAD to BAL, and then back to the selected audio mode, each time you press the TUNE knob. Treble/Bass − Use these modes to adjust the tone to your liking. Select TRE or BAS by pressing the TUNE knob. Adjust the desired mode by turning the TUNE knob.
Main Menu Table of Contents Audio System Audio System Lighting You can use the instrument panel brightness control knob to adjust the illumination of the audio system (see page 69 ). The audio system illuminates when the parking lights are on, even if the radio is turned off. Stations must use these exact frequencies. It is fairly common for stations to round-off the frequency in their advertising, so your radio could display a frequency of 100.
Main Menu Table of Contents Audio System As required by the FCC: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Radio signals, especially on the FM band, are deflected by large objects such as buildings and hills. Your radio then receives both the direct signal from the station’s transmitter, and the deflected signal. This causes the sound to distort or flutter.
Main Menu Table of Contents Audio System Operating the Cassette Player The ignition switch must be in ACCESSORY (I) or ON (II). Make sure the tape opening on the cassette is facing to the right, then insert the cassette most of the way into the slot. The system will pull it in the rest of the way, and begin to play. The tape direction indicator will light to show you which side of the cassette is playing. The ▲ indicates the side you inserted facing upward is now playing.
Main Menu Table of Contents Audio System Tape Search Functions With a cassette playing, you can use the FF, REW, SKIP, or REPEAT function to find a desired program. PWR/VOL KNOB TAPE DIRECTION INDICATOR CASSETTE SLOT TAPE EJECT BUTTON DOLBY INDICATOR FF/REW − Fast Forward and Rewind move the tape rapidly. To rewind the tape, push the REW button. You will see REW in the display. To fast forward the tape, push the FF button. You will see FF displayed.
Main Menu Table of Contents Audio System SKIP − The SKIP function allows you to find the beginning of a song or passage. To skip to the beginning of a song or passage currently − button. You will playing, push the ○ see REW flashing in the display as the tape rewinds. To skip to the beginning of the next song, push the + button. You will see FF flashing in ○ the display as the tape fast forwards. When the system finds the beginning of a song or passage, it goes back to PLAY.
Main Menu Table of Contents Audio System REPEAT − The Repeat function continuously replays the current song or passage. Press the RPT button to activate it; you will see RPT displayed as a reminder. When the system reaches the end of the song or passage currently playing, it will automatically go into rewind. When it senses the beginning of the same song or passage, the system returns to PLAY mode. It will continue to repeat this same program until you deactivate REPEAT by pressing the button again.
Main Menu Table of Contents Audio System Caring for the Cassette Player The cassette player picks up dirt and oxides from the tape. This contamination builds up over time and causes the sound quality to degrade. To prevent this, you should clean the player after every 30 hours of use. Your dealer has a cleaning kit available. Look at the cassette before you insert it. If the tape is loose, tighten it by turning a hub with a pencil or your finger.
Main Menu Table of Contents Audio System Operating the CD Changer Your Honda’s audio system has an in-dash CD changer that holds up to six discs, providing several hours of continuous entertainment. You operate this CD changer with the same controls used for the radio and cassette player. LOAD BUTTON CD SLOT CD EJECT BUTTON To load the CDs or operate the CD changer, the ignition switch must be in ACCESSORY (I) or ON (II). Load and play only standard round discs.
Main Menu Table of Contents Audio System Loading CDs in the Changer To load multiple CDs in one operation: 1. Press and hold the Load button until you hear a beep and see ‘‘LOAd’’ in the display, then release the button. 2. On the upper left side of the display, the disc number for an empty position will begin blinking and the green CD Loaded indicator will come on. 3. Insert the disc into the CD slot. Insert it only about halfway, the drive will pull it in the rest of the way.
Main Menu Table of Contents Audio System If you press the Load button while a CD is playing, the system will stop playing that CD and start the loading sequence. It will then play the CD just loaded. You can also load a CD into an empty position while a CD is playing by pressing the appropriate preset button. Select an empty position (the disc number indicator is off), and press the preset button for that position (1 to 6). The system will stop playing the current CD and start the loading sequence.
Main Menu Table of Contents Audio System Operation Select the CD changer by pressing the CD button. You will see ‘‘Cd’’ in the display. The system will begin playing the last selected disc in the CD changer. You will see the disc and track numbers displayed. When that disc ends, the next disc in the CD changer is loaded and played. After the last disc finishes, the system returns to disc 1. To select a different disc, press the appropriate Preset button (1 − 6).
Main Menu Table of Contents Audio System To take the system out of CD mode, press the AM or FM button, or insert a cassette in the player. If a tape is already in the cassette player, press the TAPE button. When you return to CD mode by pressing the CD button, play will continue at the same point that it left off.
Main Menu Table of Contents Audio System Removing CDs from the Changer To remove the disc that is currently playing, press the Eject button. You will see ‘‘EJEC’’ in the display. When you remove the disc from the slot, the system automatically begins the Load sequence so you can load another CD in that position. If you do not load another CD, after ten seconds the system begins playing the next disc in the changer. If the changer is empty, the system selects the previous mode (AM, FM, or Tape).
Main Menu Table of Contents Audio System If you press the Eject button while listening to the radio or tape, or with the audio system turned off, the disc that was last selected is ejected. After that disc is ejected, pressing the Eject button again will eject the next disc in the numerical order. By doing this six times, you can remove all the CDs from the changer. In any mode, if you press the Eject button and hold it until you hear a beep, the system will eject all of the discs in the changer.
Main Menu Table of Contents Audio System Protecting Compact Discs Handle a CD by its edges; never touch either surface. Contamination from fingerprints, liquids, felt-tip pens, and labels can cause the CD to not play properly, or possibly jam in the drive. When a CD is not being played, store it in its case to protect it from dust and other contamination. To prevent warpage, keep CDs out of direct sunlight and extreme heat. 168 Comfort and Convenience Features To clean a disc, use a clean soft cloth.
Main Menu Table of Contents Audio System CD Changer Error Indications If you see an error indication in the display while operating the CD changer, find the cause in the chart to the right. If you cannot clear the error indication, take the car to your Honda dealer. Indication Cause FOCUS Error Mechanical Error No CD in the CD changer. Solution Press the CD eject button and pull out the CDs, check for error indication. Insert the CDs again.
Main Menu Table of Contents Audio System Remote Audio Controls AUDIO/CH BUTTON The top and bottom buttons adjust the volume up (▲) or down (▼). Press the proper button and hold it until the desired volume is reached, then release it. The AUDIO/CH button has three functions, depending on whether you are listening to the radio, or playing a cassette or CD. On EX and EX-V6 models Two controls for the audio system are mounted in the steering wheel hub.
Main Menu Table of Contents Audio System Theft Protection On EX and EX-V6 models Your car’s audio system will disable itself if it is disconnected from electrical power for any reason. To make it work again, the user must enter a specific five-digit code in the Preset buttons. Because there are hundreds of number combinations possible from five digits, making the system work without knowing the exact code is nearly impossible.
Main Menu Table of Contents Security System With the system set, you can still open the trunk with the master key or the remote transmitter (if the transmitter is equipped with a trunk opener) without triggering the alarm. The alarm will sound if the trunk lock is forced, or the trunk is opened with the trunk release handle or the emergency trunk opener. Standard on EX and EX-V6 models Optional on LX and LX-V6 models The security system helps to protect your car and valuables from theft.
Main Menu Before Driving Before you begin driving your Honda, you should know what gasoline to use, and how to check the levels of important fluids. You also need to know how to properly store luggage or packages. The information in this section will help you. If you plan to add any accessories to your car, please read the information in this section first. Break-in Period .............................. 174 Gasoline .......................................... 174 Service Station Procedures ..........
Main Menu Table of Contents Break-in Period, Gasoline Break-in Period Help assure your car’s future reliability and performance by paying extra attention to how you drive during the first 600 miles (1,000 km). During this period: Avoid full-throttle starts and rapid acceleration. Avoid hard braking. New brakes need to be broken-in by moderate use for the first 200 miles (300 km). Do not change the oil until the recommended time or mileage interval shown in the maintenance schedule.
Main Menu Table of Contents Service Station Procedures Filling the Fuel Tank Push Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. Stop the engine and keep heat, sparks, and flame away. Handle fuel only outdoors. Wipe up spills immediately. 3. Remove the fuel fill cap slowly. You may hear a hissing sound as pressure inside the tank escapes. Place the cap in the holder on the fuel fill door. 4.
Main Menu Table of Contents Service Station Procedures 5. Screw the fuel fill cap back on, tighten it until it clicks several times. If you do not properly tighten the cap, the Malfunction Indicator Lamp may come on (see page 311 ). Opening the Hood HOOD RELEASE HANDLE LATCH 6. Push the fuel fill door closed until it latches. 1. Shift to Park or Neutral and set the parking brake. Pull the hood release handle located under the lower left corner of the dashboard. The hood will pop up slightly.
Main Menu Table of Contents Service Station Procedures If you can open the hood without lifting the hood latch handle, or the hood latch handle moves stiffly or does not spring back as before, the mechanism should be cleaned and lubricated (see page 251 ). SUPPORT ROD To close the hood, lift it up slightly to remove the support rod from the hole. Put the support rod back into its holding clip. Lower the hood to about a foot (30 cm) above the fender, then let it drop.
Main Menu Table of Contents Service Station Procedures Oil Check DIPSTICK 6-cylinder models 6-cylinder models Lift the hood up most of the way. The hydraulic supports will lift it up the rest of the way and hold it up. To close the hood, lower it to about a foot (30 cm) above the fender, then press down firmly with your hands. After closing the hood, make sure it is securely latched. 178 Before Driving 4-cylinder models Check the engine oil level every time you fill the car with fuel.
Main Menu Table of Contents Service Station Procedures 4-cylinder models 2. Wipe the dipstick with a clean cloth or paper towel. 6-cylinder models 3. Insert it all the way back in its tube.
Main Menu Table of Contents Service Station Procedures Engine Coolant Check RESERVE TANK MAX RESERVE TANK MAX UPPER MARK LOWER MARK 4-cylinder models 4. Remove the dipstick again and check the level. It should be between the upper and lower marks. If it is near or below the lower mark, see Adding Oil on page 230 . 180 Before Driving MIN Look at the coolant level in the radiator reserve tank. Make sure it is between the MAX and MIN lines.
Main Menu Table of Contents Fuel Economy The condition of your car and your driving habits are the two most important things that affect the fuel mileage you get. Vehicle Condition Always maintain your car according to the maintenance schedule. This will keep it in top operating condition. An important part of that maintenance is the Owner Maintenance Checks (see page 227 ). For example, an underinflated tire causes more ‘‘rolling resistance,’’ which uses fuel.
Main Menu Table of Contents Accessories and Modifications Modifying your car, or installing some non-Honda accessories, can make your car unsafe. Before you make any modifications or add any accessories, be sure to read the following information. Accessories Your dealer has Genuine Honda accessories that allow you to personalize your car. These accessories have been designed and approved for your car, and are covered by warranty. Non-Honda accessories are usually designed for universal applications.
Main Menu Table of Contents Accessories and Modifications Modifications Do not remove any original equipment or modify your car in any way that would alter its design or operation. This could make your car unsafe and illegal to drive. In addition, any modifications that decrease ground clearance increase the chance of undercarriage parts striking a curb, speed bump, or other raised object, which could cause your airbags to deploy.
Main Menu Table of Contents Carrying Cargo CONSOLE COMPARTMENT Your car has several convenient storage areas so you can stow cargo safely. DOOR POCKET The glove box, and the pockets in the doors and seat-backs, are designed for small, lightweight items. The trunk is intended for larger, heavier items. In addition, the back seat can be folded down to allow you to carry more cargo or longer items.
Main Menu Table of Contents Carrying Cargo Load Limit The maximum load for your car is 850 lbs (395 kg). This figure includes the total weight of all occupants, cargo, accessories, and the tongue weight if you are towing a trailer. To figure out how much cargo you can carry: Add up the weight of all occupants. If you are towing a trailer, add the tongue weight to the number above. Subtract the total from 850 lbs (395 kg). The final number is the total weight of cargo you can carry.
Main Menu Table of Contents Carrying Cargo Carrying Cargo in the Trunk or on a Roof Rack Distribute cargo evenly on the floor of the trunk, placing the heaviest items on the bottom and as far forward as possible. If you fold down the back seat, tie down items that could be thrown about the car during a crash or sudden stop. If you carry large items that prevent you from closing the trunk lid, exhaust gas can enter the passenger area.
Main Menu Driving This section gives you tips on starting the engine under various conditions, and how to operate the 5-speed manual and automatic transmissions. It also includes important information on parking your car, the braking system, the Traction Control System, and facts you need if you are planning to tow a trailer. Preparing to Drive ......................... 188 Starting the Engine........................ 189 Starting in Cold Weather at High Altitude .....................
Main Menu Table of Contents Preparing to Drive You should do the following checks and adjustments every day before you drive your car. 1. Make sure all windows, mirrors, and outside lights are clean and unobstructed. Remove frost, snow, or ice. 2. Check that the hood and trunk are fully closed. 3. Visually check the tires. If a tire looks low, use a gauge to check its pressure. 4. Check that any items you may be carrying with you inside are stored properly or fastened down securely. 188 Driving 5.
Main Menu Table of Contents Starting the Engine 1. Apply the parking brake. 2. In cold weather, turn off all electrical accessories to reduce the drain on the battery. 3. Manual Transmission: Push the clutch pedal down all the way. START (III) does not function unless the clutch pedal is depressed. Automatic Transmission: Make sure the shift lever is in Park. Press on the brake pedal. 4. Without touching the accelerator pedal, turn the ignition key to the START (III) position.
Main Menu Table of Contents Starting the Engine Starting in Cold Weather at High Altitude (Above 8,000 feet/ 2,400 meters) An engine is harder to start in cold weather. The thinner air found at high altitude above 8,000 feet (2,400 meters) adds to the problem. Use the following procedure: 190 Driving 1. Turn off all electrical accessories to reduce the drain on the battery. 2. Push the accelerator pedal halfway to the floor and hold it there while starting the engine.
Main Menu Table of Contents 5-speed Manual Transmission Come to a full stop before you shift into Reverse. You can damage the transmission by trying to shift into Reverse with the car moving. Push down the clutch pedal, and pause for a few seconds before shifting into Reverse, or shift into one of the forward gears for a moment. This stops the gears so they won’t ‘‘grind.’’ The manual transmission is synchronized in all forward gears for smooth operation.
Main Menu Table of Contents 5-speed Manual Transmission, Automatic Transmission Recommended Shift Points Drive in the highest gear that lets the engine run and accelerate smoothly. This will give you the best fuel economy and effective emissions control.
Main Menu Table of Contents Automatic Transmission Shift Lever Position Indicator The ‘‘D4 ’’ indicator comes on for a few seconds when you turn the ignition switch ON (II). If it flashes while driving (in any shift position), it indicates a possible problem in the transmission. Avoid rapid acceleration and have the transmission checked by an authorized Honda dealer as soon as possible.
Main Menu Table of Contents Automatic Transmission To shift from: P to R R to P N to R D3 to 2 2 to 1 1 to 2 2 to D3 D3 to D4 D4 to N D4 to D3 N to D4 R to N Do this: Press the brake pedal and press the release button. Press the release button. Move the lever. Park (P) − This position mechanically locks the transmission. Use Park whenever you are turning off or starting the engine. To shift out of Park, you must press on the brake pedal and have your foot off the accelerator pedal.
Main Menu Table of Contents Automatic Transmission Neutral (N) − Use Neutral if you need to restart a stalled engine, or if it is necessary to stop briefly with the engine idling. Shift to Park position if you need to leave the car for any reason. Press on the brake pedal when you are moving the shift lever from Neutral to another gear. Drive (D4) − Use this position for your normal driving. The transmission automatically selects a suitable gear for your speed and acceleration.
Main Menu Table of Contents Automatic Transmission First (1) − To shift from Second to First, press the release button on the side of the shift lever. With the lever in this position, the transmission locks in First gear. By upshifting and downshifting through 1, 2, D3 and D4, you can operate this transmission much like a manual transmission without a clutch pedal.
Main Menu Table of Contents Automatic Transmission If you need to use the Shift Lock Release, it means your car is developing a problem. Have the car checked by your Honda dealer. 3. Put a cloth on the edge of the Shift Lock Release slot cover next to the shift lever. Use a small flat-tipped screwdriver or small metal plate (neither are included in the tool kit) to remove the cover. Carefully pry off the edge of the cover. 4. Insert the key in the Shift Lock Release slot. 5.
Main Menu Table of Contents Parking Always use the parking brake when you park your car. The indicator on the instrument panel shows that the parking brake is not fully released; it does not indicate that the parking brake is firmly set. Make sure the parking brake is set firmly or your car may roll if it is parked on an incline. If the car is facing uphill, turn the front wheels away from the curb. If you have a manual transmission, put it in first gear.
Main Menu Table of Contents The Braking System Your Honda is equipped with front disc brakes. The brakes on the rear wheels may be disc or drum, depending on the model. A power assist helps reduce the effort needed on the brake pedal. The ABS (on cars equipped with ABS) helps you retain steering control when braking very hard. Put your foot on the brake pedal only when you intend to brake. Resting your foot on the pedal keeps the brakes applied lightly, causing them to build up heat.
Main Menu Table of Contents The Braking System Brake System Design The hydraulic system that operates the brakes has two separate circuits. Each circuit works diagonally across the vehicle (the left-front brake is connected with the right-rear brake, etc.). If one circuit should develop a problem, you will still have braking at two wheels. ABS helps to prevent the wheels from locking up and skidding during hard braking, allowing you to retain steering control.
Main Menu Table of Contents The Braking System Important Safety Reminders ABS does not reduce the time or distance it takes to stop the car, it only helps with steering control during braking. You should always maintain a safe following distance from other vehicles. ABS will not prevent a skid that results from changing direction abruptly, such as trying to take a corner too fast or making a sudden lane change. Always drive at a safe, prudent speed for the road and weather conditions.
Main Menu Table of Contents The Braking System, Traction Control System On all V6 models The TCS indicator will come on along with the ABS indicator if there is a problem with the anti-lock brake system. Traction Control System On all V6 models Your Honda is equipped with a Traction Control System (TCS) to assist you in maintaining traction while driving slowly on loose or slippery surfaces. The TCS assists only in low-speed, low-traction conditions; up to approximately 25 mph (40 km/h).
Main Menu Table of Contents Traction Control System When starting out or driving at low speeds on a loose or slippery road surface, you may notice that the vehicle does not respond to the accelerator in the same way it does at other times. This is a sign the TCS is activating. You will see the TCS indicator light flash. You should still install winter tires on your car during the winter. Make sure to use the same size originally supplied with vehicle.
Main Menu Table of Contents Traction Control System The Traction Control System turns on every time you start the engine, even if you turned it off the last time you drove the vehicle. TCS Indicator The TCS indicator comes on or flashes under the following conditions: When you turn the ignition switch to ON (II). When you manually turn off the TCS. It flashes when the TCS is regulating wheelspin. If the system’s diagnostics senses a problem in the TCS, the indicator will come on and stay on.
Main Menu Table of Contents Driving in Bad Weather Rain, fog, and snow conditions require a different driving technique because of reduced traction and visibility. Keep your car wellmaintained and exercise greater caution when you need to drive in bad weather. The cruise control should not be used in these conditions. Driving Technique − Always drive slower than you would in dry weather. It takes your car longer to react, even in conditions that may seem just barely damp.
Main Menu Table of Contents Driving in Bad Weather Visibility − Being able to see clearly in all directions and being visible to other drivers are important in all weather conditions. This is more difficult in bad weather. To be seen more clearly during daylight hours, turn on your headlights. Traction − Check your tires frequently for wear and proper pressure. Both are important in preventing ‘‘hydroplaning’’ (loss of traction on a wet surface).
Main Menu Table of Contents Towing a Trailer Your Honda has been designed primarily to carry passengers and their cargo. You can use it to tow a trailer if you carefully observe the load limits, use the proper equipment, and follow the guidelines in this section. Load Limits Total Trailer Weight: The total weight of the trailer and everything loaded in it must not exceed 1,000 lbs (450 kg). Towing a load that is too heavy can seriously affect your vehicle’s handling and performance.
Main Menu Table of Contents Towing a Trailer To achieve a proper tongue load, start by loading 60 percent of the load toward the front of the trailer and 40 percent toward the rear, then re-adjust the load as needed.
Main Menu Table of Contents Towing a Trailer Checking Loads The best way to confirm that vehicle and trailer weights are within limits is to have them checked at a public scale. Using a suitable scale or a special tongue load gauge, check the tongue load the first time you set up a towing combination (a fully-loaded vehicle and trailer), then recheck the tongue load whenever the conditions change.
Main Menu Table of Contents Towing a Trailer Trailer Brakes Honda recommends that any trailer having a total weight of 1,000 lbs (450 kg) or more be equipped with its own electric or surge-type brakes. If you choose electric brakes, be sure they are electronically actuated. Do not attempt to tap into your vehicle’s hydraulic system. No matter how successful it may seem, any attempt to attach trailer brakes to your vehicle’s hydraulic system will lower braking effectiveness and create a potential hazard.
Main Menu Table of Contents Towing a Trailer Additional Trailer Equipment Many states and Canadian provinces require special outside mirrors when towing a trailer. Even if they don’t, you should install special mirrors if you cannot clearly see behind you, or if the trailer creates a blind spot. Ask your trailer sales or rental agency if any other items are recommended or required for your towing situation.
Main Menu Table of Contents Towing a Trailer Driving Safely With a Trailer The added weight, length, and height of a trailer will affect your vehicle’s handling and performance, so driving with a trailer requires some special driving skills and techniques. For your safety and the safety of others, take time to practice driving maneuvers before heading for the open road, and follow the guidelines discussed below.
Main Menu Table of Contents Towing a Trailer Handling Crosswinds and Buffeting Parking Crosswinds and air turbulence caused by passing trucks can disrupt your steering and cause trailer swaying. When being passed by a large vehicle, keep a constant speed and steer straight ahead. Do not try to make quick steering or braking corrections. Follow all normal precautions when parking, including firmly setting the parking brake and putting the transmission in Park (automatic) or in 1st or Reverse (manual).
Main Menu 214
Main Menu Maintenance This section explains why it is important to keep your car well maintained and to follow basic maintenance safety precautions. This section also includes Maintenance Schedules for normal driving and severe driving conditions, a Maintenance Record, and instructions for simple maintenance tasks you may want to take care of yourself. If you have the skills and tools to perform more complex maintenance tasks on your Honda, you may want to purchase the Service Manual.
Main Menu Table of Contents Maintenance Safety Regularly maintaining your car is the best way to protect your investment. Proper maintenance is essential to your safety and the safety of your passengers. It will also reward you with more economical, trouble-free driving and help reduce air pollution. Improperly maintaining this car or failing to correct a problem before driving can cause a crash in which you can be seriously hurt or killed.
Main Menu Table of Contents Maintenance Safety Important Safety Precautions Before you begin any maintenance, make sure your car is parked on level ground and that the parking brake is set. Also, be sure the engine is off. This will help to eliminate several potential hazards: Carbon monoxide poisoning from engine exhaust. Be sure there is adequate ventilation whenever you operate the engine. Burns from hot parts. Let the engine and exhaust system cool before touching any parts.
Main Menu Table of Contents Maintenance Schedule The Maintenance Schedule specifies how often you should have your car serviced and what things need attention. It is essential that you have your car serviced as scheduled to retain its high level of safety, dependability, and emissions control performance. The services and time or distance intervals shown in the maintenance schedule assume you will use your car as normal transportation for passengers and their possessions.
Main Menu Table of Contents Maintenance Schedule Your authorized Honda dealer knows your car best and can provide competent, efficient service. However, service at a dealer is not mandatory to keep your warranties in effect. Maintenance may be done by any qualified service facility or person who is skilled in this type of automotive service. Keep all the receipts as proof of completion, and have the person who does the work fill out the Maintenance Record. Check your warranty booklet for more information.
Maintenance Schedule for Normal Conditions Main Menu Table of Contents miles x 1,000 Service at the indicated km x 1,000 distance or time − whichever months comes first.
Main Menu Table of Contents 7,500 mi/12,000 km 15,000 mi/24,000 km/1 yr 22,500 mi/36,000 km 30,000 mi/48,000 km/2 yrs 37,500 mi/60,000 km 45,000 mi/72,000 km/3 yrs 52,500 mi/84,000 km 60,000 mi/96,000 km/4 yrs 67,500 mi/108,000 km 75,000 mi/120,000 km/5 yrs 82,500 mi/132,000 km 90,000 mi/144,000 km/6 yrs 97,500 mi/156,000 km 105,000 mi/168,000 km/7 yrs 112,500 mi/180,000 km 120,000 mi/192,000 km/8 yrs 120,000 mi/192,000 km/10yrs 120,000 mi/192,000 km/6 yrs Do items in A. Do items in A, B. Do items in A.
Maintenance Schedule for Severe Conditions Main Menu Table of Contents Service at the indicated miles x 1,000 distance or time − whichever km x 1,000 comes first.
Main Menu Table of Contents 3,750 mi/6,000 km 7,500 mi/12,000 km 11,250 mi/18,000 km 15,000 mi/24,000 km/1 yr 18,750 mi/30,000 km 22,500 mi/36,000 km 26,250 mi/42,000 km 30,000 mi/48,000 km/2 yrs 33,750 mi/54,000 km 37,500 mi/60,000 km 41,250 mi/66,000 km 45,000 mi/72,000 km/3 yrs 48,750 mi/78,000 km 52,500 mi/84,000 km 56,250 mi/90,000 km 60,000 mi/96,000 km/4 yrs 60,000 mi/96,000 km/3 yrs 60,000 mi/96,000 km/3 yrs 63,750 mi/102,000 km 67,500 mi/108,000 km 71,250 mi/114,000 km Do items in A.
Main Menu Table of Contents Maintenance Schedule for Severe Conditions (listed by distance/time) 75,000 mi/120,000 km/5 yrs 78,750 mi/126,000 km 82,500 mi/132,000 km 86,250 mi/138,000 km 90,000 mi/144,000 km/6 yrs 90,000 mi/144,000 km/5 yrs 93,750 mi/150,000 km 97,500 mi/156,000 km 101,250 mi/162,000 km 105,000 mi/168,000 km/7 yrs 108,750 mi/174,000 km 112,500 mi/180,000 km 116,250 mi/186,000 km 120,000 mi/192,000 km/8 yrs 120,000 mi/192,000 km/10 yrs 120,000 mi/192,000 km/6 yrs 120,000 mi/192,000 km/7
Main Menu Table of Contents Required Maintenance Record (for Normal and Severe Schedules) You or the servicing dealer can record all completed maintenance here, whether you follow the schedule for normal conditions (page 220 ) or severe conditions (page 222 ). Keep the receipts for all work done on your car.
Main Menu Table of Contents Required Maintenance Record (for Normal and Severe Schedules) 63,750 mi 102,000 km Signature or dealer stamp mi/km 93,750 mi 150,000 km Date 67,500 mi 108,000 km mi/km mi/km 97,500 mi 156,000 km mi/km 78,750 mi 126,000 km mi/km Date 101,250 mi 162,000 km mi/km 105,000 mi 168,000 km (or 7 years) mi/km 108,750 mi 174,000 km mi/km mi/km 112,500 mi 180,000 km 226 Maintenance mi/km Date mi/km Date 116,250 mi 186,000 km Date 90,000 mi 144,000 km (or 6 years)
Main Menu Table of Contents Owner Maintenance Checks You should check the following items at the specified intervals. If you are unsure of how to perform any check, turn to the page given. Engine oil level − Check every time you fill the fuel tank. See page 178 . Engine coolant level − Check the radiator reserve tank every time you fill the fuel tank. See page 180 . Windshield washer fluid − Check the level in the reservoir monthly.
Main Menu Table of Contents Fluid Locations 4-cylinder Models BRAKE FLUID (Gray cap) CLUTCH FLUID (5-speed Manual Transmission only) (Gray cap) ENGINE OIL FILL CAP (Black cap) ENGINE OIL DIPSTICK (Orange loop) AUTOMATIC TRANSMISSION FLUID DIPSTICK (Yellow loop) WASHER FLUID (Blue cap) ENGINE COOLANT RESERVOIR POWER STEERING FLUID (Red cap) RADIATOR CAP 228 Maintenance
Main Menu Table of Contents Fluid Locations 6-cylinder Models ENGINE OIL FILL CAP (Black cap) BRAKE FLUID (Gray cap) ENGINE OIL DIPSTICK (Orange loop) AUTOMATIC TRANSMISSION FLUID DIPSTICK (Yellow loop) WASHER FLUID (Blue cap) ENGINE COOLANT RESERVOIR POWER STEERING FLUID (Red cap) RADIATOR CAP Maintenance 229
Main Menu Table of Contents Engine Oil Adding Oil Recommended Oil Oil is a major contributor to your engine’s performance and longevity. Always use a premium-grade 5W-20 detergent oil displaying the API Certification Seal. This seal indicates the oil is energy conserving, and that it meets the American Petroleum Institute’s latest requirements. ENGINE OIL FILL CAP 4-cylinder models To add oil, unscrew and remove the engine oil fill cap on top of the valve cover.
Main Menu Table of Contents Engine Oil Make sure the API Certification Seal says ‘‘For Gasoline Engines.’’ The SAE number tells you the oil’s viscosity or weight. Select the oil for your vehicle according to this chart. 5W-20 oil is formulated for yearround protection of your Honda, to improve cold weather starting, and to help your engine use less fuel. If 5W-20 oil is not available, a 5W-30 oil may be used. However, it should be replaced with 5W-20 at the next oil change.
Main Menu Table of Contents Engine Oil Synthetic Oil You may use a synthetic motor oil if it meets the same requirements given for a conventional motor oil: it displays the API Certification Seal, and it is the proper weight as shown on the chart. When using synthetic oil, you must follow the oil and filter change intervals given in the maintenance schedule. Additives Your Honda does not require any oil additives. Additives may adversely affect your engine’s or transmission’s performance and durability.
Main Menu Table of Contents Engine Oil WASHER 6-cylinder models DRAIN BOLT OIL FILTER OIL FILTER 4-cylinder models 6-cylinder models 3. Remove the oil filter and let the remaining oil drain. A special wrench (available from your Honda dealer) is required to remove the filter. 4. Install a new oil filter according to instructions that come with it.
Main Menu Table of Contents Engine Oil 5. Put a new washer on the drain bolt, then reinstall the drain bolt. Tighten it to: (LX, EX) 33 lbf·ft (44 N·m , 4.5 kgf·m) (LX-V6, EX-V6) 29 lbf·ft (39 N·m , 4.0 kgf·m) 6. Refill the engine with the recommended oil. Engine oil change capacity (including filter): (LX, EX) 4.5 US qt (4.3 , 3.8 Imp qt) (LX-V6, EX-V6) 4.6 US qt (4.4 , 3.9 Imp qt) 234 Maintenance 7. Replace the engine oil fill cap. Start the engine.
Main Menu Table of Contents Cooling System corrosion, causing the cooling system to malfunction or fail. Have the cooling system flushed and refilled with Honda antifreeze/ coolant as soon as possible. Adding Engine Coolant If the reserve tank is completely empty, you should also check the coolant level in the radiator. 4-cylinder models RESERVE TANK If the coolant level in the reserve tank is at or below the MIN line, add coolant to bring it up to the MAX line. Inspect the cooling system for leaks.
Main Menu Table of Contents Cooling System RADIATOR CAP 4-cylinder models 2. Turn the radiator cap counterclockwise, without pressing down on it, until it stops. This relieves any pressure remaining in the cooling system. 3. Remove the radiator cap by pushing down and turning counterclockwise. 236 Maintenance 6-cylinder models RADIATOR CAP 4. The coolant level should be up to the base of the filler neck. Add coolant if it is low. 5. Put the radiator cap back on. Tighten it fully.
Main Menu Table of Contents Cooling System Replacing Engine Coolant The cooling system should be completely drained and refilled with new coolant according to the time and distance recommendations in the maintenance schedule. Only use Honda All Season Antifreeze/ Coolant Type 2. 6-cylinder models RESERVE TANK Do not add any rust inhibitors or other additives to your car’s cooling system. They may not be compatible with the coolant or engine components.
Main Menu Table of Contents Cooling System DRAIN PLUG DRAIN BOLT DRAIN PLUG 6-cylinder models 4-cylinder models 3. 4-cylinder models Loosen the drain plug on the bottom of the radiator. The coolant will drain through the splash guard. Remove the drain bolt and washer from the engine block. 238 Maintenance 6-cylinder models DRAIN BOLT 6-cylinder models Loosen the drain plug on the bottom of the radiator. The coolant will drain through the splash guard. Loosen the drain bolt.
Main Menu Table of Contents Cooling System RESERVE TANK 4-cylinder models RESERVE TANK CAP HOLDER 4. Remove the reserve tank from its holder by pulling it straight up. Drain the coolant, then put the tank back in its holder. GROUND CABLE CRUISE CONTROL CABLE RESERVE TANK 6-cylinder models RESERVE TANK CAP HOLDER 6-cylinder models When removing the reserve tank, first remove the cruise control cable and the ground cable from their clips.
Main Menu Table of Contents Cooling System 5. When the coolant stops draining, tighten the drain plug at the bottom of the radiator. Tighten the bleeder bolt when coolant comes out in a steady stream with no bubbles. 6. 4-cylinder models Put a new washer on the drain bolt, then reinstall the drain bolt in the engine block. Tighten it securely. Tightening torque: 61 lbf·ft (83 N·m , 8.5 kgf·m) 6-cylinder models Tighten the drain bolt at the rear of the engine cylinder block securely.
Main Menu Table of Contents Cooling System FILLER NECK 12.Start the engine and let it run until the radiator cooling fan comes on at least twice. Then stop the engine. FILLER NECK 13.Remove the radiator cap. Pour coolant into the radiator up to the base of the filler neck and into the reserve tank up to the MAX mark. 4-cylinder models Fill up to here 8. Start the engine and let it run for about 30 seconds. Then turn off the engine. 9.
Main Menu Table of Contents Windshield Washers Check the level in the windshield washer reservoir at least monthly during normal usage. In bad weather, when you use the washers often, check the level every time you stop for fuel. LEVEL GAUGE LEVEL GAUGE 4-cylinder models The windshield washer reservoir is located behind the driver’s side headlight. 6-cylinder models The windshield washer reservoir is located behind the passenger’s side headlight.
Main Menu Table of Contents Transmission Fluid Automatic Transmission DIPSTICK UPPER MARK LOWER MARK 4-cylinder models DIPSTICK Check the fluid level with the engine at normal operating temperature. 6-cylinder models DIPSTICK 1. Park the car on level ground. Shut off the engine. 4-cylinder models 3. Insert the dipstick all the way into the transmission securely as shown in the illustration. 2. Remove the dipstick (yellow loop) from the transmission and wipe it with a clean cloth.
Main Menu Table of Contents Transmission Fluid DIPSTICK 5. If the level is below the lower mark, add fluid to bring it to the upper mark. 4-cylinder cars − Add fluid in the dipstick tube. 6-cylinder cars − Remove the fill plug to add fluid. UPPER MARK LOWER MARK 6-cylinder models 4. Remove the dipstick and check the fluid level. It should be between the upper and lower marks. Always use Honda ATF-Z1 (Automatic Transmission Fluid).
Main Menu Table of Contents Transmission Fluid 5-speed Manual Transmission Correct level FILLER BOLT Check the fluid level with the transmission at normal operating temperature and the car sitting on level ground. Remove the transmission filler bolt and carefully feel inside the bolt hole with your finger. The fluid level should be up to the edge of the bolt hole. If it is not, add Honda Manual Transmission Fluid (MTF) until it starts to run out of the hole.
Main Menu Table of Contents Brake and Clutch Fluid Check the fluid level in the reservoirs monthly. There are up to two reservoirs, depending on the model. They are: Brake fluid reservoir (all models) Clutch fluid reservoir (manual transmission only) The brake fluid should be replaced according to the time recommendation in the maintenance schedule. Always use Honda Heavy Duty Brake Fluid DOT 3.
Main Menu Table of Contents Brake and Clutch Fluid Clutch System MAX MAX 6-cylinder models MIN Low fluid level can indicate a leak in the clutch system. Have this system inspected as soon as possible. MIN The fluid should be between the MIN and MAX marks on the side of the reservoir. If it is not, add brake fluid to bring it up to that level. Use the same fluid specified for the brake system.
Main Menu Table of Contents Power Steering UPPER LEVEL UPPER LEVEL A low power steering fluid level can indicate a leak in the system. Check the fluid level frequently and have the system inspected as soon as possible. Turning the steering wheel to f ull lef t or right lock and holding it there can damage the power steering pump. 4-cylinder models LOWER LEVEL Check the level when the engine is cold. Look at the side of the reservoir. The fluid should be between the UPPER LEVEL and LOWER LEVEL.
Main Menu Table of Contents Air Cleaner Element The air cleaner element should be cleaned or replaced according to the time and distance recommendations in the maintenance schedule. Replacement 4-cylinder Models HOLD-DOWN CLAMPS Cleaning (Severe Conditions) Clean the air cleaner element by blowing compressed air through it in the opposite direction to normal air flow. If you do not have access to compressed air (such as a service station), ask your Honda dealer to do this service.
Main Menu Table of Contents Air Cleaner Element Replacement 6-cylinder Models BOLTS The air cleaner element is inside the air cleaner housing on the driver’s side of the engine compartment. To replace it: AIR CLEANER ELEMENT 1. Loosen the four bolts by using a Phillips-head screwdriver and remove the air cleaner housing cover. 2. Remove the old air cleaner element. 3. Carefully clean the inside of the air cleaner housing with a damp rag. 250 Maintenance 4.
Main Menu Table of Contents Hood Latch, Spark Plugs (4-cylinder Models) Hood Latch LATCH ASSEMBLY PIVOTS Clean the hood latch assembly with a mild cleaner, then lubricate it with a multipurpose grease. Lubricate all the moving parts (as shown), including the pivot. To lubricate them, remove the holding clip and pull the cover away. Follow the time and distance recommendations in the Maintenance Schedule. If you are not sure how to clean and grease the latch, contact your Honda dealer.
Main Menu Table of Contents Spark Plugs (4-cylinder Models) Tighten the spark plugs caref ully. A spark plug that is too loose can overheat and damage the engine. Overtightening can cause damage to the threads in the cylinder head. 6. Install the spark plug cap. 7. Repeat this procedure for the other three spark plugs. Specifications: 4. Put the new spark plug into the socket; then screw it into the hole. Screw it in by hand so you do not crossthread it. 252 Maintenance 5. Torque the spark plug.
Main Menu Table of Contents Spark Plugs (6-cylinder Models) The spark plugs in your car should be replaced according to the time and distance recommendations in the maintenance schedule. Replacement HOLDING CLIP 1. Loosen the two holding clips by turning the heads one-quarter turn counterclockwise with a flat-tipped screwdriver. Remove the cover on the front cylinder bank by pulling it straight up. 2. Clean up any dirt and oil that have collected around the ignition coils. 3.
Main Menu Table of Contents Spark Plugs (6-cylinder Models) HEXAGON SOCKET HEAD CAP BOLT 4. Use a wrench to remove the hexagon socket head cap bolt holding the ignition coil. Remove the ignition coil by pulling it straight out. 254 Maintenance 5. Remove the spark plug with a five-eighths inch (16 mm) spark plug socket. 6. Put the new spark plug into the socket; then screw it into the hole. Screw it in by hand so you do not crossthread it. 7. Torque the spark plug.
Main Menu Table of Contents Spark Plugs (6-cylinder Models) Tighten the spark plugs caref ully. A spark plug that is too loose can overheat and damage the engine. Overtightening can cause damage to the threads in the cylinder head. 8. Install the ignition coil. Reinstall the hexagon socket head cap bolt. 9. Push the wire connector onto the ignition coil. Make sure it locks in place. 10.Repeat this procedure for the other five spark plugs.
Main Menu Table of Contents Battery TEST INDICATOR WINDOW TEST INDICATOR WINDOW 4-cylinder models 6-cylinder models Check the condition of your car’s battery monthly. You should check the color of the test indicator window, and for corrosion on the terminals. 256 Maintenance Check the battery condition by looking at the test indicator window on the battery. The label on the battery explains the test indicator’s colors. Check the battery terminals for corrosion (a white or yellowish powder).
Main Menu Table of Contents Battery The battery gives off explosive hydrogen gas during normal operation. A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you. 4-cylinder models If the terminals are severely corroded, clean them with baking soda and water. Then use a wrench to loosen and remove the cables from the terminals. Always disconnect the negative (−) cable first and reconnect it last.
Main Menu Table of Contents Battery On EX and EX-V6 models If your car’s battery is disconnected or goes dead, the audio system will disable itself. The next time you turn on the radio you will see ‘‘ ’’ in the frequency display. Use the Preset buttons to enter the five-digit code (see page 171 ). 258 Maintenance Charging the battery with the cables connected can seriously damage your car’s electronic controls. Detach the battery cables bef ore connecting the battery to a charger.
Main Menu Table of Contents Wiper Blades Check the condition of the wiper blades at least every six months. Look for signs of cracking in the rubber, or areas that are getting hard. Replace the blades if you find these signs, or they leave streaks and unwiped areas when used. WIPER ARMS LOCK TAB To replace the blade: 1. Raise the wiper arm off the windshield. Raise the driver’s side first, then the passenger’s side. 2. Disconnect the blade assembly from the wiper arm by pushing in the lock tab.
Main Menu Table of Contents Wiper Blades BLADE BLADE 5. Slide the new wiper blade into the holder until the tabs lock. 6. Slide the wiper blade assembly onto the wiper arm. Make sure it locks in place. REINFORCEMENT 3. Remove the blade from its holder by grasping the tabbed end of the blade. Pull firmly until the tabs come out of the holder. 260 Maintenance 4. Examine the new wiper blades.
Main Menu Table of Contents Air Conditioning System Your car’s air conditioning is a sealed system. Any major maintenance, such as recharging, should be done by a qualified mechanic. You can do a couple of things to make sure the air conditioning works efficiently. Periodically check the engine’s radiator and air conditioning condenser for leaves, insects, and dirt stuck to the front surface. These block the air flow and reduce cooling efficiency.
Main Menu Table of Contents Air Conditioning Filter, Drive Belts Air Conditioning Filter The air conditioning filter removes pollen and dust that is brought in from the outside through the heating and cooling system/climate control system. This filter should be replaced every 30,000 miles (48,000 km) under normal conditions. It should be replaced every 15,000 miles (24,000 km) if you drive primarily in urban areas that have high concentrations of soot in the air from industry and diesel-powered vehicles.
Main Menu Table of Contents Drive Belts, Timing Belt The belts should have the following ‘‘play’’ or deflection. 4-cylinder models Alternator belt: 0.28−0.35 in (7.0−9.0 mm) Power steering belt: 0.51−0.63 in (13.0−16.0 mm) 6-cylinder models Power steering belt: 0.51−0.65 in (13.0−16.5 mm) If you see signs of wear or looseness, have your dealer adjust or replace the belts.
Main Menu Table of Contents Tires To safely operate your car, your tires must be the proper type and size, in good condition with adequate tread, and correctly inflated. The following pages give more detailed information on how and when to check air pressure, how to inspect your tires for damage and wear, and what to do when your tires need to be replaced. Using tires that are excessively worn or improperly inflated can cause a crash in which you can be seriously hurt or killed.
Main Menu Table of Contents Tires Recommended Tire Pressures for Normal Driving The following chart shows the recommended cold tire pressures for most normal driving conditions and speeds. Tire pressures for high speed driving are the same as for normal driving. (LX, EX) Tire Size P195/65R15 89H Cold Tire Pressure for Normal Driving 29 psi (200 kPa , 2.0 kgf/cm ) (LX-V6) Tire Size P205/65R15 92V Cold Tire Pressure for Normal Driving 30 psi (210 kPa , 2.
Main Menu Table of Contents Tires INDICATOR LOCATION MARKS TREAD WEAR INDICATORS Your car’s tires have wear indicators molded into the tread. When the tread wears down to that point, you will see a 1/2 inch (12.7 mm) wide band running across the tread. This shows there is less than 1/16 inch (1.6 mm) of tread left on the tire. A tire that is this worn gives very little traction on wet roads. You should replace the tire if you can see the tread wear indicator in three or more places around the tire.
Main Menu Table of Contents Tires Tire Rotation Front Front (For Non-directional (For Directional Tires and Wheels) Tires and Wheels) To help increase tire life and distribute wear more evenly, you should have the tires rotated every 7,500 miles (12,000 km). Move the tires to the positions shown in the chart each time they are rotated. When shopping for replacement tires, you may find that some tires are ‘‘directional.’’ This means they are designed to rotate only in one direction.
Main Menu Table of Contents Tires The ABS works by comparing the speed of the wheels. When replacing tires, use the same size originally supplied with the car. Tire size and construction can affect wheel speed and may cause the system to work inconsistently. Wheels and Tires Wheel: (LX, EX) 15 x 6 JJ If you ever need to replace a wheel, make sure the wheel’s specifications match those of the original wheel that came on your car. Replacement wheels are available at your Honda dealer.
Main Menu Table of Contents Tires Snow Tires Tire Chains All Models If you mount snow tires on your Honda, make sure they are radial tires of the same size and load range as the original tires. Mount snow tires on all four wheels to balance your car’s handling in all weather conditions. Keep in mind the traction provided by snow tires on dry roads may not be as high as your car’s original equipment tires. You should drive cautiously even when the roads are clear.
Main Menu Table of Contents Lights Check the operation of your car’s exterior lights at least once a month. A burned out bulb can create an unsafe condition by reducing your car’s visibility and the ability to signal your intentions to other drivers.
Main Menu Table of Contents Lights Check the following: TURN SIGNAL/TAILLIGHT HIGH-MOUNT BRAKE LIGHT Headlights (low and high beam) Parking lights Taillights Brake lights High-mount brake light Turn signals Back-up lights Hazard light function License plate light Side marker lights Daytime running lights (Canadian models) LICENSE PLATE LIGHTS REAR SIDE MARKER LIGHT STOP/TAILLIGHT If you find any bulbs are burned out, replace them as soon as possible.
Main Menu Table of Contents Lights Headlight Aiming The headlights were properly aimed when your car was new. If you regularly carry heavy items in the trunk or pull a trailer, readjustment may be required. Adjustment of the headlights should be performed by a Honda technician or other qualified mechanic. Replacing a Headlight Bulb Your car has two bulbs on each side, four in total. Make sure you are replacing the bulb that is burned out. Your car uses halogen headlight bulbs.
Main Menu Table of Contents Lights BULB 4. Insert the new bulb into the hole and turn it one-quarter turn clockwise to lock it in place. 5. Push the electrical connector back onto the bulb. Make sure it is on all the way. 6. Turn on the headlights to test the new bulb. TAB 2. Remove the electrical connector from the bulb by squeezing the connector to unlock the tab, then slide the connector off the bulb. 3. Remove the bulb by turning it approximately one-quarter turn counterclockwise. 7.
Main Menu Table of Contents Lights 5. Remove the burned out bulb from the socket by pushing it in and turning counterclockwise until it unlocks. Replacing Front Turn Signal and Side Marker Light Bulbs HOLDING CLIP 6. Install the new bulb in the socket. Turn it clockwise to lock it in place. 7. Insert the socket back into the headlight assembly. Turn it clockwise to lock it in place. 8. Test the lights to make sure the new bulb is working. 1.
Main Menu Table of Contents Lights 3. Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms. Replacing a Parking Light Bulb POWER STEERING FLUID TANK 4. Insert the socket back into the headlight assembly. Turn it clockwise to lock it in place. 5. Turn on the parking lights to make sure the new bulb works. HOLDER 1. Open the hood. The front parking light is next to the headlight bulb.
Main Menu Table of Contents Lights 4. Remove the socket by turning it one-quarter turn counterclockwise. Replacing Rear Bulbs (in Fenders) 5. Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms. 6. Reinstall the socket into the light assembly by turning it clockwise until it locks. 7. Test the lights to make sure the new bulb is working. FASTENER 1. Open the trunk. 2.
Main Menu Table of Contents Lights 9. Put the fastener in the hole on the side of the trunk lining and push on the center until it locks (the center is flush with the head). Replacing Rear Bulbs (in Trunk Lid) SCREW 1. Open the trunk. 2. Remove the screw securing the plastic cover. Then remove the plastic cover. 3. Determine which of the two bulbs is burned out: stop/taillight or back-up light.
Main Menu Table of Contents Lights 4. Remove the socket by turning it one-quarter turn counterclockwise. Replacing a Rear Side Marker Light Bulb 5. Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms. 6. Reinstall the socket into the light assembly. 7. Test the lights to make sure the new bulb is working. SCREW 8. Reinstall the plastic cover and secure it with the screw. 278 Maintenance 1.
Main Menu Table of Contents Lights 5. Insert the socket in the assembly. Turn it clockwise to lock it in place. Replacing a High-mount Brake Light Bulb 6. Reinstall the side marker assembly in the bumper. Tighten the mounting screw securely. 3. Reinstall the socket. Turn it clockwise until it locks. 4. Test the lights to make sure the new bulb is working. 1. Open the trunk and remove the socket from the light assembly by turning it one-quarter turn counterclockwise. 2.
Main Menu Table of Contents Lights 3. Turn on the parking lights and check that the new bulb is working. Replacing a Rear License Plate Bulb 4. Put the lens back into the light assembly, right side first. Push on the left edge until it snaps into place. 1. Insert a flat blade screwdriver between the left edge of the lens and the housing. The lens will come down. 280 Maintenance 2. Pull the bulb straight out of its socket. Push the new bulb in until it bottoms in the socket.
Main Menu Table of Contents Lights Replacing Bulbs in the Interior Courtesy Lights The ceiling light, door light and vanity mirror light come apart the same way, but they do not use the same type of bulb. CEILING LIGHT DOOR LIGHT 1. Remove the lens by carefully prying on the edge of the lens with a fingernail file or a small flat-tip screwdriver. Do not pry on the edge of the housing around the lens. Ceiling light: Pry on the front edge of the lens near both sides.
Main Menu Table of Contents Lights SPOTLIGHT VANITY MIRROR LIGHT Replacing the Trunk Light Bulb TRUNK LIGHT LENS Spotlights: Pry on the front edge in front of both spotlights. 2. Remove the bulb by pulling it straight out of its metal tabs. 3. Push the new bulb into the metal tabs. Snap the lens back in place. 1. Open the trunk. Pull down the trunk light cover. 2. Remove the bulb by pulling it straight out of its metal tabs. 3. Push the new bulb into the metal tabs. 4. Push the cover back in place.
Main Menu Table of Contents Storing Your Car If you need to park your car for an extended period (more than one month), there are several things you should do to prepare it for storage. Proper preparation helps prevent deterioration and makes it easier to get your car back on the road. If possible, store your car indoors. Block the rear wheels. If the car is to be stored for a longer period, it should be supported on jackstands so the tires are off the ground.
Main Menu 284
Main Menu Appearance Care Regular cleaning and polishing of your Honda helps to keep it ‘‘new’’ looking. This section gives you hints on how to clean your car and preserve its appearance: the paint, brightwork, wheels and interior. Also included are several things you can do to help prevent corrosion. Exterior Care.................................. 286 Washing ...................................... 286 Waxing ........................................ 287 Aluminum Wheels .....................
Main Menu Table of Contents Exterior Care Washing Frequent washing helps preserve your car’s beauty. Dirt and grit can scratch the paint, while tree sap and bird droppings can permanently ruin the finish. Wash your car in a shady area, not in direct sunlight. If the car is parked in the sun, move it into the shade and let the exterior cool down before you start. Only use the solvents and cleaners recommended in this Owner’s Manual.
Main Menu Table of Contents Exterior Care Waxing Always wash and dry the whole car before waxing it. You should wax your car, including the metal trim, whenever water sits on the surface in large patches. It should form into beads or droplets after waxing. You should use a quality liquid or paste wax. Apply it according to the instructions on the container. In general, there are two types of products: Waxes − A wax coats the finish and protects it from damage by exposure to sunlight, air pollution, etc.
Main Menu Table of Contents Interior Care Carpeting Vacuum the carpeting frequently to remove dirt. Ground-in dirt will make the carpet wear out faster. Periodically shampoo the carpet to keep it looking new. Use one of the foam-type carpet cleaners on the market. Follow the instructions that come with the cleaner, applying it with a sponge or soft brush. Keep the carpeting as dry as possible by not adding water to the foam.
Main Menu Table of Contents Interior Care Fabric Vacuum dirt and dust out of the material frequently. For general cleaning, use a solution of mild soap and lukewarm water, letting it air dry. To clean off stubborn spots, use a commercially-available fabric cleaner. Test it on a hidden area of the fabric first, to make sure it does not bleach or stain the fabric. Follow the instructions that come with the cleaner. Vinyl Remove dirt and dust with a vacuum cleaner.
Main Menu Table of Contents Interior Care Dirt build-up in the loops of the seat belt anchors can cause the belts to retract slowly. Wipe the insides of the loops with a clean cloth dampened in mild soap and warm water or isopropyl alcohol. Windows Clean the windows, inside and out, with a commercially-available glass cleaner. You can also use a mixture of one part white vinegar to ten parts water. This will remove the haze that builds up on the inside of the windows.
Main Menu Table of Contents Corrosion Protection Two factors normally contribute to causing corrosion in your car: 1. Moisture trapped in body cavities. Dirt and road salt that collects in hollows on the underside of the car stays damp, promoting corrosion in that area. 2. Removal of paint and protective coatings from the exterior and underside of the car. Many corrosion-preventive measures are built into your Honda.
Main Menu Table of Contents Body Repairs Body repairs can affect your car’s resistance to corrosion. If your car needs repairs after a collision, pay close attention to the parts used in the repair and the quality of the work. Make sure the repair facility uses genuine Honda replacement body parts. Some companies make sheet metal pieces that seem to duplicate the original Honda body parts, but are actually inferior in fit, finish, and corrosion resistance.
Main Menu Taking Care of the Unexpected This section covers the morecommon problems that motorists experience with their vehicles. It gives you information about how to safely evaluate the problem and what to do to correct it. If the problem has stranded you on the side of the road, you may be able to get going again. If not, you will also find instructions on getting your car towed. Compact Spare Tire....................... 294 Changing a Flat Tire ..................... 295 If Your Engine Won’t Start ...
Main Menu Table of Contents Compact Spare Tire Your car has a compact spare tire that takes up less space. Use this spare tire as a temporary replacement only. Get your regular tire repaired or replaced and put it back on your car as soon as you can. Check the inflation pressure of the compact spare tire every time you check the other tires. It should be inflated to: 60 psi (420 kPa , 4.
Main Menu Table of Contents Changing a Flat Tire If you have a flat tire while driving, stop in a safe place to change it. Stopping in traffic or on the shoulder of a busy road is dangerous. Drive slowly along the shoulder until you get to an exit or an area to stop that is far away from the traffic lanes. The car can easily roll off the jack, seriously injuring anyone underneath. Follow the directions for changing a tire exactly, and never get under the car when it is supported only by the jack. 1.
Main Menu Table of Contents Changing a Flat Tire WHEEL NUTS JACK COVER 5. Unscrew the wing bolt and take the spare tire out of its well. 6. The jack is behind a cover in the right fender. Remove the cover by turning the handle counterclockwise, then pulling on the cover. 296 Taking Care of the Unexpected WHEEL WRENCH 7. Turn the jack’s end bracket counterclockwise to loosen it, then remove the jack. 8.
Main Menu Table of Contents Changing a Flat Tire EXTENSION JACKING POINT 9. Locate the jacking point nearest the tire you need to change. It is pointed to by a △ mark molded into the underside of the body. Place the jack under the jacking point. Turn the end bracket clockwise until the top of the jack contacts the jacking point. Make sure the jacking point tab is resting in the jack notch. WHEEL WRENCH 10.
Main Menu Table of Contents Changing a Flat Tire WHEEL COVER WHEEL NUTS On LX and LX-V6 models Do not attempt to forcibly pry the wheel cover off with a screwdriver or other tool. The wheel cover cannot be removed without first removing the wheel nuts. 298 Taking Care of the Unexpected BRAKE HUB 12. Before mounting the spare tire, wipe any dirt off the mounting surface of the wheel and hub with a clean cloth. Wipe the hub carefully, it may be hot from driving. 13. Put on the spare tire.
Main Menu Table of Contents Changing a Flat Tire 4-cylinder models 14. Lower the car to the ground and remove the jack. 6-cylinder models 15. Tighten the wheel nuts securely in the same crisscross pattern. Have the wheel nut torque checked at the nearest automotive service facility.
Main Menu Table of Contents Changing a Flat Tire WING BOLT SPACER CONE 20. Store the jack in its holder. Turn the jack’s end bracket to lock it in place. Replace the cover. Store the tools. Loose items can fly around the interior in a crash and could seriously injure the occupants. CENTER CAP 16. On EX and EX-V6 models Remove the center cap before storing the flat tire in the trunk well. 17. Place the flat tire face down in the spare tire well. 18.
Main Menu Table of Contents If Your Engine Won’t Start Diagnosing why your engine won’t start falls into two areas, depending on what you hear when you turn the key to START (III): You hear nothing, or almost nothing. The engine’s starter motor does not operate at all, or operates very slowly. You can hear the starter motor operating normally, or the starter motor sounds like it is spinning faster than normal, but the engine does not start up and run.
Main Menu Table of Contents If Your Engine Won’t Start The Starter Operates Normally In this case, the starter motor’s speed sounds normal, or even faster than normal, when you turn the ignition switch to START (III), but the engine does not run. Your car has the Immobilizer System. You should use a properly-coded master or valet key to start the engine (see page 78 ). A key that is not properly coded will cause the immobilizer system indicator in the dash panel to blink rapidly.
Main Menu Table of Contents Jump Starting If your car’s battery has run down, you may be able to start the engine by using a booster battery. Although this seems like a simple procedure, you should take several precautions. A battery can explode if you do not follow the correct procedure, seriously injuring anyone nearby. To jump start your car, follow these directions closely: 1. Open the hood and check the physical condition of the battery (see page 256 ).
Main Menu Table of Contents Jump Starting 6-cylinder models 4-cylinder models 4. Connect the second jumper cable to the negative (−) terminal on the booster battery. Connect the other end to the grounding strap as shown. Do not connect this jumper cable to any other part of the engine.
Main Menu Table of Contents Jump Starting 7. Once your car is running, disconnect the negative cable from your car, then from the booster battery. Disconnect the positive cable from your car, then the booster battery. 4-cylinder models BOOSTER BATTERY 5. If the booster battery is in another vehicle, have an assistant start that vehicle and run it at a fast idle.
Main Menu Table of Contents If Your Engine Overheats The pointer of your car’s temperature gauge should stay in the midrange under most conditions. It may go higher if you are driving up a long steep hill on a very hot day. If it climbs to the red mark, you should determine the reason. Driving with the temperature gauge pointer at the red mark can cause serious damage to your engine. Your car can overheat for several reasons, such as lack of coolant or a mechanical problem.
Main Menu Table of Contents If Your Engine Overheats 3. If you do not see steam or spray, leave the engine running and watch the temperature gauge. If the high heat is due to overloading (climbing a long, steep hill on a hot day with the A/C running, for example), the engine should start to cool down almost immediately. If it does, wait until the temperature gauge comes down to the midpoint then continue driving. 5. Wait until you see no more signs of steam or spray, then open the hood. 4.
Main Menu Table of Contents If Your Engine Overheats 9. Using gloves or a large heavy cloth, turn the radiator cap counterclockwise, without pushing down, to the first stop. This releases any remaining pressure in the cooling system. After the pressure releases, push down on the cap and turn it until it comes off. 308 Taking Care of the Unexpected 10.Start the engine and set the temperature control dial to maximum (climate control to FULL AUTO at 90°F/32°C).
Main Menu Table of Contents Low Oil Pressure Indicator LOW OIL PRESSURE INDICATOR Running the engine with low oil pressure can cause serious mechanical damage almost immediately. Turn of f the engine as soon as you can saf ely get the car stopped. 4. Start the engine and watch the oil pressure indicator. If the light does not go out within ten seconds, turn off the engine. There is a mechanical problem that needs to be repaired before you can continue driving. (See Emergency Towing on page 320 .) 1.
Main Menu Table of Contents Charging System Indicator Immediately turn off all electrical accessories: radio, heater, A/C, climate control, rear defogger, cruise control, etc. Try not to use other electrically-operated controls such as the power windows. Keep the engine running and take extra care not to stall it. Starting the engine will discharge the battery rapidly. CHARGING SYSTEM INDICATOR This indicator should come on when the ignition switch is ON (II), and go out after the engine starts.
Main Menu Table of Contents Malfunction Indicator Lamp MALFUNCTION INDICATOR LAMP This indicator comes on for a few seconds when you turn the ignition switch ON (II). If it comes on at any other time, it indicates one of the engine’s emissions control systems may have a problem. Even though you may feel no difference in your car’s performance, it can reduce your fuel economy and cause your car to put out excessive emissions. Continued operation may cause serious damage.
Main Menu Table of Contents Malfunction Indicator Lamp Readiness Codes Your car has certain ‘‘readiness codes’’ that are part of the on-board diagnostics for the emissions systems. In some states, part of the emissions testing is to make sure these codes are set. If they are not set, the test cannot be completed. If your car’s battery has been disconnected or gone dead, these codes are erased. It takes several days of driving under various conditions to set the codes again.
Main Menu Table of Contents Brake System Indicator BRAKE SYSTEM INDICATOR* * U.S. indicator shown The Brake System Indicator normally comes on when you turn the ignition switch ON (II). It is a reminder to check the parking brake. It comes on and stays lit if you do not fully release the parking brake. If it comes on at any other time, it indicates a problem with the car’s brake system. In most cases, the problem is a low fluid level in the brake fluid reservoir.
Main Menu Table of Contents Closing the Moonroof If the electric motor will not close the moonroof, do the following: ROUND PLUG SOCKET 1. Check the fuse for the moonroof motor (see page 315 ). If the fuse is blown, replace it with one of the same or lower rating. 2. Try closing the moonroof. If the new fuse blows immediately or the moonroof motor still does not operate, you can close the moonroof manually. 3. Get the moonroof wrench out of the tool kit in the trunk. 4.
Main Menu Table of Contents Fuses All the electrical circuits in your car have fuses to protect them from a short circuit or overload. These fuses are located in three fuse boxes. INTERIOR UNDER-HOOD TAB COVER The interior fuse boxes are located on each side of the dashboard. To open an interior fuse box, open the car door. Pull the cover open, then take it out of its hinges by pulling it toward you. The under-hood fuse box is located in the back of the engine compartment on the passenger’s side.
Main Menu Table of Contents Fuses Checking and Replacing Fuses If something electrical in your car stops working, the first thing you should check for is a blown fuse. Determine from the chart on pages 318 and 319 , or the diagram on the fuse box lid, which fuse or fuses control that component. Check those fuses first, but check all the fuses before deciding that a blown fuse is not the cause. Replace any blown fuses and check the component’s operation. 1. Turn the ignition switch to LOCK (0).
Main Menu Table of Contents Fuses BLOWN If you cannot drive the car without fixing the problem, and you do not have a spare fuse, take a fuse of the same rating or a lower rating from one of the other circuits. Make sure you can do without that circuit temporarily (such as the accessory power socket or radio). 6. If the replacement fuse of the same rating blows in a short time, there is probably a serious electrical problem in your car.
Main Menu Table of Contents Fuses INTERIOR FUSE BOX Driver’s Side Front ← Passenger’s Side No. Amps. 1 2 3 15 A 10 A 7.5 A 4 5 6 7.5 A 7.5 A 15 A 7 8 9 7.5 A 7.5 A 7.5 A 10 11 12 13 7.5 A 15 A 30 A 7.5 A Circuits Protected Fuel Pump SRS Heater Control, A/C Clutch Relay, Cooling Fan Relay Power Mirror Daytime Running Light* ECU (ECM/PCM), Cruise Control SRS, Moonroof ACC Relay Back-up Lights, Meter Lights Turn Signals IG Coil Wiper Starter Signal * : On Canadian models → Front No. Amps.
Main Menu Table of Contents Fuses UNDER-HOOD FUSE BOX No. Amps. 1 2 3 4 5 6 7 8 9 10 11 12 13 20 A 7.5 A 20 A 20 A 20 A 15 A 30 A 15 A 20 A 30 A 100 A 20 A 40 A Circuits Protected Left Headlight Dimmer Relay*1 Right Headlight ABS F/S*2 Stop ACG ABS Motor*2 Hazard Spare Fuse Spare Fuse Battery Cooling Fan Back Up, ACC No. Amps. 14 15 16 17 18 19 20 21 22 23 24 40 A 40 A 20 A 40 A 40 A 7.
Main Menu Table of Contents Emergency Towing If your car needs to be towed, call a professional towing service or, if you belong to one, an organization that provides roadside assistance. Never tow your car behind another vehicle with just a rope or chain. It is very dangerous. There are three popular types of professional towing equipment. Flat-bed Equipment − The operator loads your car on the back of a truck. This is the best way to transport your Honda.
Main Menu Table of Contents Emergency Towing If you decide to tow your car with all four wheels on the ground, make sure you use a properly-designed and attached tow bar. Prepare the car for towing as described above, and leave the ignition switch in Accessory (I) so the steering wheel does not lock. Make sure the radio and any items plugged into the accessory power socket are turned off so they do not run down the battery. Trying to lif t or tow your car by the bumpers will cause serious damage.
Main Menu 322
Main Menu Technical Information The diagrams in this section give you the dimensions and capacities of your Honda, and the locations of the identification numbers. It also includes information you should know about your vehicle’s tires and emissions control systems. Identification Numbers ................. 324 Specifications (4-cylinder Models) ................... 326 Specifications (6-cylinder Models) ................... 328 DOT Tire Quality Grading (U.S. Cars) ..............................
Main Menu Table of Contents Identification Numbers Your car has several identifying numbers located in various places. VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is the 17-digit number your Honda dealer uses to register your car for warranty purposes. It is also necessary for licensing and insuring your car. The easiest place to find the VIN is on a plate fastened to the top of the dashboard. You can see it by looking through the windshield on the driver’s side.
Main Menu Table of Contents Identification Numbers The Engine Number is stamped into the engine block. It is on the front. 4-cylinder Models AUTOMATIC TRANSMISSION NUMBER The Transmission Number is on a label on top of the transmission.
Main Menu Table of Contents Specifications (4-cylinder Models) Dimensions Length Width Height Wheelbase Track Front Rear Weights Gross vehicle weight rating Air Conditioning Refrigerant type Charge quantity Lubricant type 187.7 in (4,767 mm) 70.3 in (1,785 mm) 54.9 in (1,395 mm) 105.1 in (2,670 mm) 61.2 in (1,555 mm) 60.4 in (1,535 mm) See the certification label attached to the driver’s doorjamb. HFC-134a (R-134a) 24.7−26.5 oz (700−750 g) ND-OIL8 Capacities Fuel tank Approx. 17.12 US gal (64.
Main Menu Table of Contents Specifications (4-cylinder Models) Lights Headlights High Low Front turn signal/side marker lights Front parking lights Rear turn signal/taillights Stop/Taillights Back-up lights Rear side marker lights License plate lights Ceiling light High-mount brake light Trunk light Door courtesy lights Vanity mirror light Spotlights Battery Capacity Fuses Interior Under-hood 12 V − 60 W (HB3) 12 V − 51 W (HB4) 12 V − 24/2.
Main Menu Table of Contents Specifications (6-cylinder Models) Dimensions Length Width Height Wheelbase Track Front Rear Weights Gross vehicle weight rating Air Conditioning Refrigerant type Charge quantity Lubricant type 187.7 in (4,767 mm) 70.3 in (1,785 mm) 55.3 in (1,405 mm) 105.1 in (2,670 mm) 61.2 in (1,555 mm) 60.4 in (1,535 mm) See the certification label attached to the driver’s doorjamb. HFC-134a (R-134a) 15.8−17.5 oz (450−500 g) ND-OIL8 Capacities Fuel tank Approx. 17.12 US gal (64.
Main Menu Table of Contents Specifications (6-cylinder Models) Lights Headlights High Low Front turn signal/side marker lights Front parking lights Rear turn signal/taillights Stop/Taillights Back-up lights Rear side marker lights License plate lights Ceiling light High-mount brake light Trunk light Door courtesy lights Vanity mirror light Spotlights Battery Capacity Fuses Interior Under-hood 12 V − 60 W (HB3) 12 V − 51 W (HB4) 12 V − 24/2.
Main Menu Table of Contents DOT Tire Quality Grading (U.S. Cars) The tires on your car meet all U.S. Federal Safety Requirements. All tires are also graded for treadwear, traction, and temperature performance according to Department of Transportation (DOT) standards. The following explains these gradings. Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between the tread shoulder and the maximum section width.
Main Menu Table of Contents DOT Tire Quality Grading (U.S. Cars) Temperature − A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Main Menu Table of Contents Oxygenated Fuels Some conventional gasolines are being blended with alcohol or an ether compound. These gasolines are collectively referred to as oxygenated fuels. To meet clean air standards, some areas of the United States and Canada use oxygenated fuels to help reduce emissions. If you use an oxygenated fuel, be sure it is unleaded and meets the minimum octane rating requirement. Before using an oxygenated fuel, try to confirm the fuel’s contents.
Main Menu Table of Contents Driving in Foreign Countries If you are planning to take your Honda outside the U.S. or Canada, contact the tourist bureaus in the areas you will be traveling in to find out about the availability of unleaded gasoline with the proper octane rating. If unleaded gasoline is not available, be aware that using leaded gasoline in your Honda will affect performance and fuel mileage, and damage its emissions controls. It will no longer comply with U.S.
Main Menu Table of Contents Emissions Controls The burning of gasoline in your car’s engine produces several byproducts. Some of these are carbon monoxide (CO), oxides of nitrogen (NOx) and hydrocarbons (HC). Gasoline evaporating from the tank also produces hydrocarbons. Controlling the production of NOx, CO, and HC is important to the environment. Under certain conditions of sunlight and climate, NOx and HC react to form photochemical ‘‘smog.
Main Menu Table of Contents Emissions Controls Exhaust Emissions Controls The exhaust emissions controls include four systems: PGM-FI, Ignition Timing Control, Exhaust Gas Recirculation and Three Way Catalytic Converter. These four systems work together to control the engine’s combustion and minimize the amount of HC, CO, and NOx that comes out the tailpipe. The exhaust emissions control systems are separate from the crankcase and evaporative emissions control systems.
Main Menu Table of Contents Three Way Catalytic Converter Keep the engine tuned-up. The three way catalytic converter contains precious metals that serve as catalysts, promoting chemical reactions to convert the exhaust gasses without affecting the metals. The catalytic converter is referred to as a three-way catalyst, since it acts on HC, CO, and NOx. A replacement unit must be an original Honda part or its equivalent.
Main Menu Table of Contents State Emissions Testing Testing of Readiness Codes If you take your vehicle for a state emissions test shortly after the battery has been disconnected or gone dead, it may not complete the test. This is because of certain ‘‘readiness codes’’ that must be set in the on-board diagnostics for the emissions systems. These codes are erased when the battery is disconnected, and set again only after several days of driving under a variety of conditions.
Main Menu Table of Contents State Emissions Testing Select a nearby lightly traveled major highway where you can maintain a speed of 50 to 60 mph (80 to 97 km/h) for at least 20 minutes. Drive on the highway in D4 (A/T) or 5th (M/T). Do not use the cruise control. When traffic allows, drive for 90 seconds without moving the accelerator pedal. (Vehicle speed may vary slightly; this is okay.
Main Menu Warranty and Customer Relations Customer Relations Information ................................. 340 U.S. Zone Office Map .................... 341 Canada Zone Office Map .............. 342 Warranty Coverages ..................... 343 Reporting Safety Defects (U.S. Vehicles) ........................... 344 Authorized Manuals ......................
Main Menu Table of Contents Customer Relations Information Honda dealership personnel are trained professionals. They should be able to answer all your questions. If you encounter a problem that your dealership does not solve to your satisfaction, please discuss it with the dealership’s management. The Service Manager or General Manager can help. Almost all problems are solved in this way.
Main Menu Table of Contents U.S. Zone Office Map Western Zone P.O. Box 2260 700 Van Ness Avenue Torrance, California 90501-1490 (310) 781-4565 Mid-Atlantic Zone 902 Wind River Ln., Suite 200 Gaithersburg, Maryland 20878 (301) 990-2020 1 ZONE 2 ZONE 8 ZONE 9 ZONE 4 ZONE 5 ZONE 10 ZONE 1 ZONE 6 ZONE 15 Northwestern Zone P.O. Box 20186 12439 N.E.
Main Menu Table of Contents Canada Zone Office Map CUSTOMER RELATIONS RELATIONS AVEC LA CLIENTÈLE Honda Canada Inc. 715 Milner Avenue Toronto, ON M1B 2K8 Tel: 1-888-9-HONDA-9 Fax: Toll-free 1-877-939-0909 Toronto (416) 287-4776 Honda Canada Inc.
Main Menu Table of Contents Warranty Coverages U.S. Owners Your new Honda is covered by these warranties: New Vehicle Limited Warranty − covers your new vehicle, except for the battery, emissions control systems and accessories, against defects in materials and workmanship. Emissions Control Systems Defects Warranty and Emissions Performance Warranty − these two warranties cover your vehicle’s emissions control systems. Time, mileage, and coverage are conditional.
Main Menu Table of Contents Reporting Safety Defects (U.S. Vehicles) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying American Honda Motor Co., Inc.
Main Menu Table of Contents Authorized Manuals Purchasing Factory Authorized Manuals (U.S. only) The following publications covering the operation and servicing of your vehicle can be obtained from Helm Incorporated, either by filling out the attached form or, for credit card holders, calling the toll-free phone number on the form. For manuals prior to the year shown below, contact Helm Incorporated, P.O. Box 07280, Detroit, Michigan 48207, or call 1-800-782-4356.
Main Menu Table of Contents Authorized Manuals NOTE: Dealers and Companies please provide dealer or company name, and also the name of the person to whose attention the shipment should be sent. For purchases outside U.S.A. please write to the address shown below for a quotation. S H I P T O Customer Name Attention Street Address − No P.O.
Main Menu Index A Accessories and Modifications .... 182 Accessories................................. 182 Additional Safety Precautions .. 183 Modifications ............................. 183 ACCESSORY (Ignition Key Position) ........................................ 81 Accessory Power Socket .............. 113 Additives, Engine Oil..................... 232 Airbag (SRS) ................................ 9, 45 Air Cleaner Element ...................... 249 Air Conditioning Filter ..................
Main Menu Index Bulb Replacement Spotlights .................................... 281 Trunk Light ................................ 282 Turn Signal Lights ..................... 274 Bulbs, Halogen ............................... 272 C Capacities Chart .................... 326, 328 Carbon Monoxide Hazard .............. 52 Carrying Cargo .............................. 184 Cassette Player Care ............................................. 160 Operation ............................
Main Menu Index Directional Signals ........................... 69 Disc Brake Wear Indicators ......... 199 Disposal of Used Oil ...................... 234 Doors Locking and Unlocking ............... 81 Monitor Light ............................... 61 Power Door Locks ....................... 81 DOT Tire Quality Grading ........... 330 Downshifting, 5-speed Manual Transmission .............................. 191 Drive Belts ...................................... 262 Driver and Passenger Safety ............
Main Menu Index Fluids Clutch .......................................... 247 Manual Transmission ............... 245 Power Steering........................... 248 Windshield Washers ................. 242 FM Stereo Radio Reception ............................ 134, 149 Folding Rear Seat .......................... 100 Foreign Countries, Driving in ...... 333 Four-way Flashers ........................... 71 Front Airbags ............................... 9, 45 Fuel ...............................................
Main Menu Index Timing Control System ............. 335 Immobilizer System......................... 78 Important Safety Precautions .......... 6 Indicators, Instrument Panel .......... 57 Infant Restraint ................................ 20 Infant Seats ....................................... 29 Tether Anchorage Points ........... 40 Inflation, Proper Tire .................... 264 Inside Mirror .................................. 106 Inspection, Tire .............................. 265 Instrument Panel .....
Main Menu Index NOTICE, Explanation of .................... i Numbers, Identification ................ 324 O Octane Requirement, Gasoline .... 174 Odometer .......................................... 63 Odometer, Trip ................................ 64 Oil Change, How to ......................... 232 Change, When to ....................... 220 Checking Engine ....................... 178 Pressure Indicator ............... 58, 309 Selecting Proper Viscosity Chart .......................................
Main Menu Index Timing Belt ................................. 263 Tires ............................................ 267 Wiper Blades .............................. 259 Replacing Seat Belts After a Crash ............................................. 44 Reserve Tank, Engine Coolant .... 180 Restraint, Child ................................ 20 Reverse Gear Position................... 194 Rotation, Tire ................................. 267 S Safety Belts...................................
Main Menu Index Steam Coming from Engine ......... 306 Steering Wheel Adjustment ................................... 73 Anti-theft Column Lock .............. 80 Stereo Sound System ............ 133, 148 Storing Your Car ............................ 283 Sun Visor......................................... 112 Sunglasses Holder ......................... 109 Supplemental Restraint System................................... 9, 45 Servicing ....................................... 50 SRS Indicator..................
Main Menu Index U Underside, Cleaning ...................... 291 Unexpected, Taking Care of the ........................................... 293 Uniform Tire Quality Grading ..... 330 Unleaded Gasoline......................... 174 Upholstery Cleaning...................... 289 Used Oil, How to Dispose of ........ 234 V Vanity Mirror ................................. 112 Vehicle Capacity Load .................. 185 Vehicle Dimensions .............. 326, 328 Vehicle Identification Number.....
Main Menu Service Information Summary Gasoline: Unleaded gasoline, pump octane number of 86 or higher. Fuel Tank Capacity: 17.12 US gal (64.8 , 14.26 Imp gal) Recommended Engine Oil: API Premium grade 5W-20 detergent oil (see page 230). Oil change capacity (including filter): LX, EX 4.5 US qt (4.3 , 3.8 Imp qt) LX-V6, EX-V6 4.6 US qt (4.4 , 3.9 Imp qt) Automatic Transmission Fluid: Honda ATF-Z1 (Automatic Transmission Fluid) preferred, or a DEXRON III ATF as a temporary replacement (see page 244 ).