S2000 2001 Online Reference Owner's Manual Use these links (and links throughout this manual) to navigate through this reference. For a printed owner's manual, click on authorized manuals or go to www.helminc.com. Contents Owner's Identification Form Introduction ....................................................................................................................................... i A Few Words About Safety....................................................................................
Main Menu Owner's Identification OWNER This Owner's Manual should be considered a permanent part of the car, and should remain with the car when it is sold. ADDRESS STREET Main Menu CITY STATE/PROVINCE V. I. N. DELIVERY DATE (Date sold to original retail purchaser) DEALER NAME ADDRESS ZIP CODE / POSTAL CODE DEALER NO.
Main Menu Introduction Congratulations on your selection of the 2001 Honda S2000. We are certain you will be pleased with your purchase of one of the most sophisticated and technologically-advanced sports cars in the world. One of the best ways to enhance the enjoyment of your new Honda is to read this manual. In it, you will learn how to operate its driving controls and convenience items. Afterwards, keep this owner's manual in your car so you can refer to it at any time.
Main Menu Main Menu A Few Words About Safety A Few Words About Safety Your safety, and the safety of others, isYour very safety, important. operating this and And the safety of others, vehicle is an And important is verysafely important. operating this responsibility. car safely is an important responsibility.
Main Menu Your Car at a Glance HEADLIGHTS/TURN SIGNAL SWITCH (P.51) WINDSHIELD WIPER CONTROLS (P.53) HEATING AND AIR CONDITIONING (P.86) HOOD RELEASE HANDLE (P.118) DOOR LOCK SWITCH (P.62) AUDIO SYSTEM (P.94) POWER WINDOW SWITCHES (P.70) MIRROR CONTROLS (P.80) ROOF SWITCH (P.73) HAZARD WARNING SWITCH (P.
Main Menu Your Car at a Glance REMOTE AUDIO CONTROLS (P.113) INSTRUMENT PANEL BRIGHTNESS (P.52) ENGINE START BUTTON (P.131) WINDSHIELD WIPERS/ WASHERS (P.53) HEADLIGHTS/TURN SIGNALS (P.51) HOOD RELEASE HANDLE (P.118) CRUISE CONTROL MASTER SWITCH (P.
Main Menu 4
Main Menu Driver and Passenger Safety This section gives you important information about how to protect yourself and your passenger. It shows you how to use seat belts properly. It explains your Supplemental Restraint System. And it tells you how to properly restrain children in your car. Important Safety Precautions .......... 6 Your Car's Safety Features .............. 7 Seat Belts........................................8 Airbags........................................... .9 Seats & Seat-Backs..........
Main Menu Table of Contents Important Safety Precautions You'll find many safety recommendations throughout this section, and throughout this manual. The recommendations on this page are the ones we consider to be the most important. Always Wear Your Seat Belt A seat belt is your best protection in all types of collisions. Airbags supplement seat belts, but airbags are designed to inflate only in a moderate to severe frontal collision.
Main Menu Table of Contents Your Car's Safety Features Your car is equipped with many features that work together to protect you and your passenger during a crash. (1) (2) (3) (4) (5) (6) (7) (8) (9) Safety Cage Crush Zones Seats & Seat-Backs Head Restraints Collapsible Steering Column Seat Belts Seat Belt Tensioners Airbags Door Locks Some safety features do not require any action on your part.
Main Menu Table of Contents Your Car's Safety Features ０３／０７／１０ Seat Belts For your safety, and the safety of your passenger, your car is equipped with seat belts in both seating positions. Your seat belt system also includes a light on the instrument panel to remind you and your passenger to fasten your seat belts. Why Wear Seat Belts Seat belts have proven to be the single most effective safety device.
Main Menu Table of Contents Your Car's Safety Features Airbags The most important things you need to know about your airbags are: Airbags do not replace seat belts. The seat belts are the occupants' primary protection in all types of collisions. Airbags supplement seat belts by providing extra protection for occupants' heads and chests. Your car has a Supplemental Restraint System (SRS) with frontal airbags to help protect the driver and a passenger.
Main Menu Table of Contents Your Car's Safety Features Seats & Seat-Backs Your car's seats are designed to keep you in a comfortable, upright position so you can take full advantage of the protection offered by seat belts and the energy absorbing materials in the seats. How you adjust your seats and seatbacks can also affect your safety.
Main Menu Table of Contents Your Car's Safety Features Pre-Drive Safety Checklist To make sure you and your passenger get the maximum protection from your car's safety features, check the following each time before you drive away: You and any adult passenger, or a larger child who has outgrown child seats, are wearing your seat belts and wearing them properly (see page 15 ). A small child riding in a forwardfacing child seat is properly restrained (see page 26).
Main Menu Table of Contents Protecting Adults Introduction The following pages provide instructions on how to properly protect adult occupants. Your car has a door monitor light on the instrument panel to indicate when a specific door is not tightly closed. These instructions also apply to a child whom you have decided is large enough and mature enough to ride as a passenger. (See page 29 for important additional guidelines on how to properly protect larger children.
Main Menu Table of Contents Protecting Adults To reduce the chance of injury, wear your seat belt properly, sit upright with your back against the seat, and move the seat as far back as possible from the１６：１１：０９ steering wheel ３１Ｓ５Ａ９３０ while still ０３／０７／１０ maintaining full control of the car. Also make sure your passenger moves the seat as far to the rear as possible. Sitting too close to an airbag can result in serious injury or death if the airbags inflate.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ Protecting Adults Reclining a seat-back so that the shoulder part of the belt no longer rests against the occupant's chest reduces the protective capability of the belt. It also increases the chance of sliding under the belt in a crash and being seriously injured. The farther a seat-back is reclined, the greater the risk of injury. Reclining the seat-back too far can result in serious injury or death in a crash.
Main Menu Table of Contents Protecting Adults ０３／０７／１０ 4.Fasten and Position the Seat Belts Insert the latch plate into the buckle, then tug on the belt to make sure the belt is securely latched. Also check that the belt is not twisted, because a twisted belt can cause serious injuries in a crash. １６：１１：０９ ３１Ｓ５Ａ９３０ spreads the forces of a crash over the strongest bones in your upper body. Improperly positioning the seat belts can cause serious injury or death in a crash.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２ Protecting Adults If a seat belt does not seem to work as it should, it may not protect the occupant in a crash. No one should sit in a seat with an inoperative seat belt. Anyone using a seat belt that is not working properly can be seriously injured or killed. Have your Honda dealer check the belt as soon as possible. See page 33 for additional information about your seat belt system and how to take care of your belts. 5.
Main Menu Table of Contents Protecting Adults Advice for Pregnant Women Because protecting the mother is the best way to protect her unborn child, a pregnant woman should always wear a seat belt whenever she drives or rides in a vehicle. Remember to keep the lap portion of the belt as low as possible across your hips. Pregnant women should also sit upright and as far back as possible from the steering wheel or dashboard.
Main Menu Table of Contents Protecting Adults Additional Safety Precautions Two people should never use the same seat belt. If they do, they could be very seriously injured in a crash. Do not put any accessories on seat belts. Devices intended to improve occupant comfort or reposition the shoulder part of a seat belt can severely compromise the protective capability of the seat belt and increase the chance of serious injury in a crash.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Protecting Children Children who are unrestrained or improperly restrained can be seriously injured or killed in a crash. Any child too small for a seat belt should be properly restrained in a child seat. A larger child should be properly restrained with a seat belt. Children depend on adults to protect them. However, despite their best intentions, many parents and other adults may not know how to properly protect young passengers.
Main Menu Table of Contents Protecting Children Your Car is Not Recommended for Child Passengers We strongly recommend that you do not carry any child in this car. One reason is that your car does not have a back seat, and accident statistics show that a child of any size or age is safer when they are properly restrained in the back seat of a vehicle. In addition, your car has a passenger's airbag which poses serious risks to children — particularly infants and small children.
Main Menu Table of Contents Protecting Children U.S. Models To remind you of the passenger's airbag hazards, your car has warning labels on the dashboard and on the driver's and passenger's visors. Please read and follow the instructions on these labels. Canadian Models To remind you of the airbag hazards, your car has warning labels on the driver's and passenger's visors. Please read and follow the instructions on these labels.
Main Menu Table of Contents Protecting Children Additional Safety Precaution Do not leave a child alone in your car. Leaving a child without adult supervision is illegal in most states and Canadian provinces and can be very hazardous. For example, a small child left in a car on a hot day can die from heatstroke. A child left alone with the key in the ignition can accidentally set the car in motion, possibly injuring themselves or others. Lock both doors and the trunk when your car is not in use.
Main Menu Table of Contents Protecting Children Selecting a Child Seat To provide proper protection, a child seat should meet three requirements: 2. The child seat should be of the proper type and size to fit the child. 3. The child seat should fit the passenger's seat. Due to variations in the design of child seats, vehicle seats, and seat belts, all child seats will not fit all seating positions in all cars. 1.The child seat should meet safety standards.
Main Menu Table of Contents Protecting Children Placing a Child Seat This page briefly summarizes Honda's recommendations on where to place a child seat in your car. Airbags Pose Serious Risks to Children The passenger's airbag inflates with enough force to kill or seriously injure an infant in a rear-facing child seat. A small child in a forward-facing child seat is also at risk.
Main Menu Table of Contents Protecting Children Installing a Child Seat After selecting a proper child seat, there are three main steps in installing the seat: 1. Secure the child seat to the car with a seat belt. All child seats must be secured to the car with the lap part of a lap/shoulder belt. A child whose seat is not properly secured to the car can be endangered in a crash. See page 27 for instructions on how to secure a forward-facing child seat in this car. 2.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２ Protecting Children Protecting Small Children If you decide to carry a small child in this car, follow the instructions and guidelines below. Child Seat Type A child who can sit up without support, and who fits within the child seat maker's weight and height limits, should be restrained in a forward-facing, upright child seat. The passenger's airbag poses serious risks to small children.
Main Menu Table of Contents Protecting Children Child Seat Installation The passenger's seat belt has a locking mechanism that must be activated to secure a child seat. The following pages provide instructions and tips on how to secure a forward-facing child seat with this type of seat belt. 1. Move the vehicle seat to the rearmost position. Moving the seat as far back as possible reduces the chance of a child being injured or killed if the passenger's airbag inflates.
Main Menu Table of Contents Protecting Children Additional Precautions for Small Children Never hold a small child on your lap. If you are not wearing a seat belt in a crash, you could be thrown forward into the dashboard and crush the child. 5. After confirming that the belt is locked, grab the shoulder part of the belt near the buckle and pull up to remove any slack from the lap part of the belt. Remember, if the lap part of the belt is not tight, the child seat will not be secure.
Main Menu Table of Contents Protecting Children Checking Seat Belt Fit If a child is too short for the shoulder Protecting Larger Children part of the belt to properly fit, we The passenger's airbag poses recommend that the child use a serious risks to children, including those who have outgrown child seats. booster seat until the child is tall enough to use the seat belt without a If the vehicle seat is too far forward, booster.
Main Menu Table of Contents Protecting Children However, if the belt touches or crosses the child's neck, the child needs to use a booster seat. Do not let a child wear a seat belt across the neck. This could result in serious neck injuries during a crash. Do not let a child put the shoulder part of a seat belt behind the back or under the arm. This could cause very serious injuries during a crash. It also increases the chance that the child will slide under the belt in a crash and be injured.
Main Menu Table of Contents Protecting Children A child may continue using a booster seat until the tops of the ears are even with the top of the seat-back. A child of this height should be tall enough to use the lap/shoulder belt without a booster. When Can a Larger Child Ride in this Car Children vary widely. And while age may be one indicator of when a child can safely ride in this car, there are other important factors you should consider.
Main Menu Table of Contents Protecting Children If you decide that a child can safely ride in this car, be sure to: Carefully read the owner's manual and make sure you understand all seat belt instructions and all safety information. Move the vehicle seat to the rearmost position. Have the child sit up straight, back against the seat, and feet on or near the floor. Check that the child's seat belt is properly positioned and secured. Driver and Passenger Safety Supervise the child.
Main Menu Table of Contents Additional Information About Your Seat Belts Seat Belt System Components Your seat belt system includes lap/ shoulder belts in both seating positions. The seat belts are also equipped with automatic seat belt tensioners. The system also includes a light on the instrument panel to remind you and your passenger to fasten your belts. If the driver's seat belt is not fastened before the ignition is turned ON (II), the light will come on and a beeper will also sound.
Main Menu ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２ Table of Contents Additional Information About Your Seat Belts To deactivate the locking mechanism, unlatch the buckle and let the seat belt fully retract. To refasten the belt, pull it out only as far as needed. See page 15 for instructions on how to wear the lap/shoulder belt properly. Seat Belt Maintenance For safety, you should check the condition of your seat belts regularly. Pull each belt out fully and look for frays, cuts, burns, and wear.
Main Menu Table of Contents Additional Information About Your SRS SRS Components Your Supplemental Restraint System (SRS) includes: Two front airbags. The driver's airbag is stored in the center of the steering wheel; the front passenger's airbag is stored in the dashboard. Both are marked "SRS AIRBAG." Automatic seat belt tensioners that tighten the front seat belts during a moderate to severe frontal collision. Sensors that can detect a moderate to severe frontal collision.
Main Menu Table of Contents Additional Information About Your SRS After a crash, you may see what looks like smoke. This is actually powder from the airbag's surface. Although the powder is not harmful, people with respiratory problems may experience some temporary discomfort. If this occurs, get out of the car as soon as it is safe to do so. During a crash, your seat belt helps restrain your lower body and torso, while the tensioner tightens and locks the seat belt to help keep you in place.
Main Menu Table of Contents Additional Information About Your SRS How the Automatic Seat Belt Tensioners Work Your Honda has automatic seat belt tensioners lor added protection during a moderate to severe frontal collision. If your airbags inflate, the lensioners immediately tighten the front seat belts to help hold the occupants in place. The belts will remain tight until you unbuckle them in the normal way. How the SRS Indicator Light If the light conies on or flashes on Works and off while you drive.
Main Menu Table of Contents Additional Information About Your SRS SRS Service Your Supplemental Restraint System is virtually maintenance-free, and there are no parts you can safely service. However, you must have your car serviced if: Your airbags ever inflate. The airbags, seat belt tensioners, and control unit must be replaced. Do not try to remove or replace the airbags yourself. This must be done by a Honda dealer or a knowledgeable body shop. The SRS indicator light alerts you to a problem.
Main Menu Table of Contents０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Carbon Monoxide Hazard Your car's exhaust contains carbon monoxide gas. You should have no problem with carbon monoxide entering the car in normal driving if you maintain your car properly. Have the exhaust system inspected for leaks whenever: The car is raised for an oil change. You notice a change in the sound of the exhaust. The car was in an accident that may have damaged the underside. Carbon monoxide gas is toxic.
Main Menu Table of Contents Safety Labels These labels are in the locations shown. They warn you of potential hazards that could cause serious injury. Read these labels carefully. SUN VISOR U.S. models Canadian models If a label comes off or becomes hard to read, contact your Honda dealer for a replacement. SEAT BELT TENSIONER DASHBOARD U.S.
Main Menu Instruments and Controls This section gives information about the controls and displays that contribute to the daily operation of your Honda. All the essential controls are within easy reach. Control Locations............................ 42 Indicator Lights................................ 43 Gauges............................................. . 47 Speedometer................................ 47 Select Button................................ 47 Tachometer................................. .
Main Menu Table of Contents Control Locations HEADLIGHT/TURN SIGNAL SWITCH (P.51) WINDSHIELD WIPER CONTROLS (P.53) HOOD RELEASE HANDLE (P.118) DOOR LOCK SWITCH (P.62) HEATING AND AIR CONDITIONING (P.86) POWER WINDOW SWITCHES (P.70) AUDIO SYSTEM (P.94) MIRROR CONTROLS (P.80) ROOF SWITCH (P.73) Instruments and Controls HAZARD WARNING SWITCH (P.
Main Menu Table of Contents Indicator Lights CRUISE CONTROL INDICATOR (P.46) MAINTENANCE REQUIRED INDICATOR (P.49) TURN SIGNAL AND HAZARD WARNING INDICATORS (P.46) ELECTRIC POWER STEERING INDICATOR (P.45) HIGH BEAM INDICATOR (P.46) LOW FUEL INDICATOR (P.46) SEAT BELT REMINDER LIGHT (P.44) SUPPLEMENTAL RESTRAINT SYSTEM INDICATOR (P.45) ANTI-LOCK BRAKE SYSTEM (ABS) INDICATOR* (P.45) DOOR-OPEN INDICATOR (P.45) TRUNK-OPEN INDICATOR (P.45) PARKING BRAKE AND BRAKE SYSTEM INDICATOR* (P.
Main Menu Table of Contents Indicator Lights The instrument panel has many indicators to give you important information about your car. Seat Belt Reminder Light This indicator flashes for several seconds when you turn the ignition ON (II). It flashes as a reminder to you and your passenger to fasten the seat belts. A beeper also sounds if you have not fastened your seat belt. If you do not fasten your seat belt, the beeper will stop after a few seconds but the light stays on until you do.
Main Menu Table of Contents Indicator Lights Supplemental Restraint System Indicator This indicator lights when you turn the ignition switch ON (II). If it comes on at any other time, it indicates a problem in the supplemental restraint system. For complete information, see page 37. SRS U.S. ABS Canada Anti-lock Brake System (ABS) Indicator This light normally comes on for a few seconds when you turn the ignition switch ON (II), and when you push the START button.
Main Menu Table of Contents Indicator Lights Turn Signal and Hazard Warning Indicators The left or right turn signal light blinks when you signal a lane change or turn. If the light does not blink or blinks rapidly, it usually means one of the turn signal bulbs is burned out (see page 192 ). Replace the bulb as soon as possible, since other drivers cannot see that you are signalling. When you turn on the Hazard Warning switch, both turn signal lights blink.
Main Menu Table of Contents Gauges TEMPERATURE GAUGE SPEEDOMETER TACHOMETER SELECT BUTTON Liquid crystal is used in the meter panel. You may feel the indicators appear slowly in the low temperature. Speedometer This shows your speed in miles per hour (mph) or kilometers per hour (km/h). Select Button The Select button switches the speedometer reading between miles per hour and kilometer per hour. It also changes the odometer and trip meters to read in miles or kilometers correspondingly.
Main Menu Table of Contents Gauges TRIP METER FUEL GAUGE TRIP BUTTON Trip Meter This meter shows the number of miles or kilometers driven since you last reset it. There are two trip meters, Trip A and Trip B. Switch between Trip A and Trip B by pressing the TRIP button repeatedly. Each trip meter works independently, so you can keep track of two different distances. ODOMETER Fuel Gauge This shows how much fuel you have. It is most accurate when the car is on level ground.
Main Menu Table of Contents Gauges Maintenance Required Indicator When the distance driven since the last scheduled maintenance reaches 6,000 miles (9,600 km), the indicator starts blinking. If you exceed 7,500 miles (12,000 km), the indicator stays on. Your dealer will reset the indicator when they perform the scheduled maintenance. If someone else performs the maintenance, reset the indicator yourself.
Main Menu Table of Contents Controls Near the Steering Wheel The two levers on the steering column contain controls for driving features you use most often. The left lever controls the turn signals, headlights, and high beams. The right lever controls the windshield washers and wipers. HEADLIGHTS/TURN SIGNALS (P.51) INSTRUMENT PANEL BRIGHTNESS (P.52) REMOTE AUDIO CONTROLS (P.113) The engine start button and the remote audio controls are under the left air vent.
Main Menu Table of Contents Controls Near the Steering Wheel Headlights The rotating switch on the left lever controls the lights. Turning this switch to the position turns on the parking lights, taillights, instrument panel lights, side-marker lights, and rear license plate lights. Turning the switch to the position turns on the headlights. If you leave the lights on with the ignition switch in ACCESSORY (I) or LOCK (0), you will hear a reminder tone when you open the driver's door.
Main Menu Table of Contents Controls Near the Steering Wheel Daytime Running Lights Canadian models only With the headlight switch off, the high beam headlights come on with reduced brightness when you turn the ignition switch to ON (II) and release the parking brake. They remain on until you turn the ignition off, even if you set the parking brake. The headlights revert to normal operation when you turn them on with the switch.
Main Menu Table of Contents Controls Near the Steering Wheel To signal a lane change, push lightly on the turn signal lever in the proper direction and hold it. The lever will return to the center position as soon as you release it. Turn Signals Windshield Wipers TURN SIGNAL LEVER Signal a turn or lane change with this lever. Push down on the lever to signal a left turn, and up to signal a right turn.
Main Menu Table of Contents Controls Near the Steering Wheel Windshield Washers In intermittent, the wipers operate every few seconds. In low speed and high speed, the wipers run continuously. To operate the wipers in mist mode, push the control lever up from the OFF position. The wipers run at high speed until you release the lever. This gives you a quick way to clear the windshield. Instruments and Controls To clean the windshield, pull back on the wiper control lever.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Steering Wheel Controls Cruise Control Cruise control allows you to maintain a set speed above 25 mph (40 km/h) without keeping your foot on the accelerator pedal. It should be used for cruising on straight, open highways. It is not recommended for conditions such as city driving, winding roads, slippery roads, heavy rain, or bad weather. You should have full control of the car under those conditions.
Main Menu Table of Contents Steering Wheel Controls RESUME/accel cruise control. To resume the set speed, press the RESUME/accel button. The CRUISE CONTROL light on the instrument panel comes on. Changing the Set Speed You can increase the set cruising speed in any of these ways: SET/decel 3. Press and release the SET/decel button on the steering wheel. The CRUISE CONTROL light on the instrument panel comes on to show the system is now activated.
Main Menu Table of Contents Steering Wheel Controls Even with the cruise control turned on, you can still use the accelerator pedal to speed up for passing. After completing the pass, take your foot off the accelerator pedal. The car will return to the set cruising speed. Resting your foot on the brake or clutch pedal will cause the cruise control to cancel. Cancelling the Cruise Control You can cancel the cruise control in any of these ways: Tap the brake or clutch pedal.
Main Menu Table of Contents Keys and Locks Keys KEY NUMBER PLATE MASTER KEY (BLACK) VALET KEY (GREY) Your car comes with two master keys and a valet key. The master key fits all the locks on your car: Ignition Doors Trunk Lower console compartment Instruments and Controls The valet key works only in the ignition and the door locks. You can keep the trunk and the lower console compartment locked when you leave your car and the valet key at a parking facility.
Main Menu Table of Contents Keys and Locks Immobilizer System The Immobilizer System protects your car from theft. A properlycoded master or valet key must be used in the ignition switch for the engine to start. If an improperlycoded key (or other device) is used, the engine's fuel system is disabled. When you turn the ignition switch to ON (II), the Immobilizer System indicator should come on for a few seconds, then go out.
Main Menu Table of Contents Keys and Locks As required by the FCC: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Main Menu Table of Contents Keys and Locks ACCESSORY (I) - In this position, you can operate the audio system and the accessory power socket. ON (II) — This is the normal key position when driving. All features and accessories on the car are usable. Several of the lights on the instrument panel come on as a test when you turn the ignition switch from ACCESSORY to ON.
Main Menu Table of Contents Keys and Locks Power Door Locks LOCK TAB Each door has a lock tab next to the inside door handle. When you push in the lock tab on the driver's door, both doors lock. Pulling out the lock tab on the driver's door only unlocks that door. The lock tab on the passenger's door only locks and unlocks that door. Instruments and Controls To lock the passenger's door when getting out of the car, push the lock tab in and close the door.
Main Menu Table of Contents Keys and Locks Remote Transmitter LED LOCK BUTTON TRUNK RELEASE BUTTON UNLOCK BUTTON PANIC BUTTON You can lock and unlock your car with the remote transmitter. When you push the LOCK button, both doors lock. The side marker lights and taillights flash once. When you push the UNLOCK button once, only the driver's door unlocks. The parking lights and taillights flash twice. The passenger's door unlocks when you push the button a second time.
Main Menu Table of Contents Keys and Locks Panic Mode Panic mode allows you to remotely activate your car's security system to attract attention. When activated, the horn will sound, and the exterior lights will flash for about 30 seconds. To activate panic mode, press and hold the PANIC button for about one second. To cancel Panic mode before 30 seconds, press any button on the remote transmitter. You can also turn the ignition switch to ON (II).
Main Menu Table of Contents Keys and Locks BATTERY ROUND COVER Remove the old battery and note the polarity. Make sure the polarity of the new battery is the same (+ side facing up), then insert it in the transmitter. Align the mark on the cover with the mark on the transmitter, then set the cover in place and turn it clockwise. Transmitter Care Avoid severe shock to the transmitter, such as dropping or throwing it. Also, protect it from extreme hot or cold temperatures.
Main Menu Table of Contents Keys and Locks See page 124 for cargo loading and weight limit information. Keep the trunk lid closed at all times while driving to avoid damaging the lid, and to prevent exhaust gas from getting into the interior. See Carbon Monoxide Hazard on page 39 . Trunk Push TRUNK RELEASE BUTTON You can open the trunk in three ways: Press the trunk release button in the lower console compartment. Use the master key to open the trunk lock. The valet key does not work in this lock.
Main Menu Table of Contents Keys and Locks Emergency Trunk Opener (U.S. models only) Parents should decide if their children should be shown how to use this feature. For more information about child safety, see page 22 . As a safety feature, your car has a release lever on the trunk latch so the trunk can be opened from the inside. To open the trunk, push the release lever to the left.
Main Menu Table of Contents Keys and Locks Console Compartments MASTER KEY The area between the seats has two compartments. Open the lower compartment by squeezing the handle. Close it with a firm push. You can lock or unlock the lower compartment with the master key. Instruments and Controls The lever to open the upper compartment is inside the lower compartment. Push up the lever and lift the lid. To close, lower the lid and push it down until it latches.
Main Menu Table of Contents Seat Adjustments See pages 12 — 13 for important safety information and warnings about how to properly position seats and seat-backs. Make all seat adjustments before you start driving. To adjust the seat forward and backward, pull up on the lever under the seat cushion's front edge. Move the seat to the desired position and release the lever. Try to move the seat to make sure it is locked in position.
Main Menu Table of Contents Power Windows Your car's windows are electricallypowered. Turn the ignition switch to ON (II) to raise or lower either window. DRIVER'S WINDOW SWITCH MAIN SWITCH PASSENGER'S WINDOW SWITCH Each door has a switch that controls its window. To open the window, push the switch down and hold it. Release the switch when you want the window to stop. Close the window by pulling back on the switch and holding it.
０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Main Menu Table of Contents Power Windows Closing a power window on someone's hands or fingers can cause serious injury. Make sure your passenger is away from the window before closing it. The master control panel also contains these extra features: AUTO — To open the driver's window fully, push the window switch firmly down and release it. The window automatically goes all the way down.
Main Menu Table of Contents Convertible Top The convertible top on your Honda lowers and raises electrically. Do not lower or raise the top while the engine is running. Before operating the convertible top, make sure the car is parked on level ground, and that there is enough clearance above the top. Do not operate the convertible top if the car is raised on the jack, a hoist, or on jack stands. It is advisable to raise the top whenever you park the car.
Main Menu Table of Contents Convertible Top LOCKING LEVER LATCH 4. Push the top forward while you release the latches from the windshield header by pushing the locking levers forward. LOCKING LEVER 5. With the latches released, pull back on the locking levers and push them up until they latch. ROOF SWITCH 6. Pull back and hold the ROOF switch.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２ Convertible Top Operating the convertible top while any part of a passenger is in the way of the convertible top can cause serious injury. Make sure that you, your passenger or any other people around the car are clear of the way of the moving convertible top. The windows will lower and the roof will fold back. Release the ROOF switch when the roof is retracted completely into the rear shelf.
Main Menu Table of Contents Convertible Top Raising the Convertible Top 1. Apply the parking brake. The convertible top will not operate unless the parking brake is fully engaged. 2. Turn the ignition switch to ON (II). ROOF SWITCH 3. Push the ROOF switch forward and hold it. 4. The windows, if raised, will lower automatically.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２ Convertible Top WINDSHIELD HEADER TAB LATCH Operating the convertible top while any part of a passenger is in the way of the convertible top can cause serious injury. LOCKING LEVER The convertible top will raise. Release the ROOF switch when the top reaches the windshield header. 5. Push in the tab on each locking lever and pull the locking lever down. 6.
Main Menu Table of Contents Convertible Top Convertible Top Cover Use the convertible top cover when the top is folded to help prevent foreign objects, dirt, etc., from getting into the material and mechanism. 1. Remove the convertible top cover from the trunk. 2. Connect the snaps on the top cover to the four pins on the back of the interior panel. 3. Hook the fastener string to the pin on each side wall of the passenger compartment.
Main Menu Table of Contents Convertible Top Maintenance 4. Fit deep the rear part of the top cover into the space behind the convertible top. 5. To remove the top cover, reverse the attaching procedure. Instruments and Controls Dust is the main cause of creaks or other sounds coming from the convertible top. Regularly clean the body seals with glass cleaner and a soft cloth. Do not use a scraper or de-icing chemicals to remove frost, snow, or ice from the top or rear window.
Main Menu Table of Contents Convertible Top To reduce the possibility of leaks: Use the door pull to open and close the door. Do not push or pull on the door glass. The convertible top seals are designed to promote the flow of water off the roof. Spraying high pressure water directly on the seals can distort them, causing a leak. Use only a low pressure water stream when using a hose, and avoid car washes. Do not lean or sit on an open door.
Main Menu Table of Contents Hazard Warning, Mirrors Hazard Warning Mirrors Adjusting the Power Mirrors SELECTOR SWITCH TAB Push the red button next to the roof switch to turn on the hazard warning lights (four-way flashers). This causes all four outside turn signals and both indicators in the instrument panel to flash. Use the hazard warning lights if you need to park in a dangerous area near heavy traffic, or if your vehicle is disabled.
Main Menu Table of Contents Mirrors, Parking Brake Parking Brake NOTICE Driving the car with the parking brake applied can damage the rear brakes and axles. 3. Push the appropriate edge of the adjustment switch to move the mirror right, left, up, or clown. 4. When you finish, move the selector switch to the center (off) position. This turns off the adjustment switch so you can't move a mirror out of position by accidentally bumping the switch. To apply the parking brake, pull the lever up fully.
Main Menu Table of Contents Beverage Holder, Accessory Power Socket, Audio Panel Beverage Holder Accessory Power Socket Audio Panel To open the beverage holder, push on the front edge. To use the accessory power socket, pull out on the cover. The ignition switch must be in ACCESSORY (I) or ON (II). To open the audio panel, push on the top center and let the panel swing down. To close, pivot the panel up and push on it until it latches. Refer to page 94 for operation of the audio system.
Main Menu Table of Contents Interior Lights The interior light has a threeposition switch. In the OFF position, the light does not come on. In the center position, the interior light comes on when you open either door. In the ON position, the interior light stays on continuously. In addition, when the three position switch is in the center position with both doors closed, the two bulbs in the interior light can be turned on separately by the pushbutton switches next to them.
Main Menu 84
Main Menu Comfort and Convenience Features The heating and air conditioning systems in your Honda provide a comfortable driving environment in all weather conditions. The standard audio system has many features. This section describes those features and how to use them. (If you selected an optional audio system, refer to the operating instructions that came with it.) Heating and Cooling........................ 86 What Each Control Does............ 86 How to Use the System...............
Main Menu Table of Contents Heating and Cooling Proper use of the Heating and Cooling system can make the interior dry and comfortable, and keep the windows clear for best visibility. What Each Control Does Fan Control Lever Pushing this lever up and down increases and decreases the fan speed. The indicators next to the lever show you the speed selected. Temperature Control Dial Turning this dial clockwise increases the temperature of the air flow.
Main Menu Table of Contents Heating and Cooling Mode Control Dial Use the MODE control dial to select the vents the air flows from. Air flows from the vents on both sides of the instrument panel, and from the dashboard vent in front of the passenger. Air flow is divided between the vents in the dashboard and the floor vents. Air flows from the center vents in the dashboard above the audio system, the vents on both sides of the instrument panel and from the floor vents.
Main Menu Table of Contents Heating and Cooling Vent Controls CENTER VENT You can adjust the direction of the air coming from the vents on both sides of the instrument panel and at the corner of the dashboard on the passenger's side. To adjust the air flow up and down, move the tab in the center of each vent up and down. To adjust it left and right, turn the dial under each vent left and right.
Main Menu Table of Contents Heating and Cooling It is best to leave the system in Fresh Air mode under almost all conditions. Keeping the system in Recirculation mode, particularly with the A/C off, can cause the windows to fog up. Switch to Recirculation mode when you are driving through smoky or dusty conditions, then switch back to Fresh Air mode when the condition clears. The outside air intakes for the heating and cooling system are at the base of the windshield.
Main Menu Table of Contents Heating and Cooling To Cool with A/C 1. Turn on the A/C by pressing the button. The light in the button comes on when a fan speed is selected. 2. Make sure the temperature control dial is all the way to the left. 3. Select 4. If the outside air is humid, select Recirculation mode. If the outside air is dry, select Fresh Air mode. Set the fan to the desired speed.
Main Menu Table of Contents Heating and Cooling To Heat To warm the interior: 1. Start the engine. 2. Select and Fresh Air mode. 3. Set the fan to the desired speed. 4. Adjust the warmth of the air with the temperature control dial. To Heat and Dehumidify with Air Conditioning Air conditioning, as it cools, removes moisture from the air. When used in combination with the heater, it makes the interior warm and dry. To Defog and Defrost To remove fog from the inside of the windows: 1. Switch the fan on.
Main Menu Table of Contents Heating and Cooling To remove exterior frost or ice from the windshield and side windows after the vehicle has been sitting out in cold weather: 1. Start the engine. 2. Select When you select the system automatically switches to Fresh Air mode and turns on the A/C. 3. Switch the fan and temperature controls to maximum. To rapidly remove exterior frost or ice from the windshield (on very cold days), first select the Recirculation mode.
Main Menu Table of Contents Heating and Cooling These settings direct all the air flow to the defroster vents at the base of the windshield and the side window defroster vents. The air flow will get warmer and clear the windows faster as the engine warms up. You can close the side vents with the dial beside each vent. This will send more warm air to the windshield defroster vents. For safety, make sure you have a clear view through all the windows before driving away.
Main Menu Table of Contents Audio System A M / F M / CD Audio System Your Honda's audio system provides clear reception on botli AM and FM bands, while the preset buttons allow you to easily select your favorite stations. The anti-theft feature will disable the system if it is disconnected from the vehicle's battery. To get the system working again, you must enter a code number (see page 114 ).
Main Menu Table of Contents Audio System Operating the Radio The ignition switch must be in ACCESSORY (I) or ON (II) to operate the audio system. Turn the system on by pushing the PWR/ VOL knob. Adjust the volume by turning the same knob. The band and frequency that the radio was last tuned to is displayed. To change bands, press the A M / FM button. On the FM band, ST will be displayed if the station is broadcasting in stereo. Stereo reproduction on AM is not available.
Main Menu Table of Contents Audio System SCAN — The SCAN function samples all the stations with strong signals on the selected band. To activate it, press the SCAN button, then release it. When the system is in the SCAN mode, SCAN shows in the display. The system will scan up the band for a station with a strong signal. When it finds one, it will stop and play that station for approximately five seconds.
Main Menu Table of Contents Audio System To store a frequency: 1. Select the desired band, AM or FM. FM1 and FM2 let you store two frequencies with each Preset button. AM/FM BUTTON SEEK BAR TUNE BAR 2. Use the TUNE or SEEK function to tune the radio to a desired station. 3. Pick the Preset button you want for that station. Press the button and hold it until you hear a beep. 4. Repeat steps 1 to 3 to store a total of six stations on AM and twelve on FM.
Main Menu Table of Contents Audio System AUTO SELECT — If you are traveling far from home and can no longer receive the stations you preset, you can use the Auto Select feature to find stations in the local area. To activate Auto Select, press the A. SEL button. A. SEL will flash in the display, and the system will go into scan mode for several seconds. It automatically scans both bands, looking for stations with strong signals.
Main Menu Table of Contents Audio System Adjusting the Sound Balance/Fader — These two controls adjust the strength of the sound coming from each speaker. The Balance control adjusts the sideto-side strength, while the Fader control adjusts the front-to-back strength. To adjust the fader, push on the BASS/FADER control knob to get it to pop out. Pull it out slightly farther, and adjust the front-to-back sound to your liking.
Main Menu Table of Contents Audio System Digital Clock The display of your audio system usually shows the time when the ignition switch is in ACCESSORY (I) or ON (II). It shows operation mode of radio, CD player, or optional CD changer when you operate them, and goes back to the time display after five seconds. The display also goes hack to the time display two seconds after you turn the volume knob to adjust the volume.
Main Menu Table of Contents Audio System To set the time, press the CLOCK (AM/FM) button for more than two seconds until you hear a beep. The time display will begin blinking. To set the hour, press and hold the H (Preset 4) button until the hour advances to the desired time. CLOCK BUTTON To set the minutes, press and hold the M (Preset 5) button until the numbers advance to the desired time. When you are finished, press the CLOCK button again.
Main Menu Table of Contents Audio System Audio System Lighting The audio system illuminates when the parking lights are on, even if the radio is turned off. Radio Frequencies Your Honda's radio can receive the complete AM and FM bands. Those bands cover these frequencies: AM band: 530 to 1,710 kilohertz FM band: 87.7 to 107.9 megahertz Radio stations on the AM band are assigned frequencies at least ten kilohertz apart (530, 540, 550). Stations on the FM band are assigned frequencies at least 0.
Main Menu Table of Contents Audio System Radio Reception How well your Honda's radio receives stations is dependent on many factors, such as the distance from the station's transmitter, nearby large objects, and atmospheric conditions. A radio station's signal gets weaker as you get farther away from its transmitter. If you are listening to an AM station, you will notice the sound volume becoming weaker, and the station drifting in and out.
Main Menu Table of Contents Audio System Electrical interference from passing vehicles and stationary sources can cause temporary reception problems. As required by the FCC: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Radio signals, especially on the FM band, are deflected by large objects such as buildings and hills.
Main Menu Table of Contents Audio System Operating the CD Player You operate the CD player with the same controls used for the radio. With the ignition switch in ACCESSORY (I) or ON (II), insert the disc into the CD slot. Push the disc in halfway, the drive will pull it in the rest of the way and begin to play. The number of the track that is playing is shown in the display. AM/FM BUTTON CD SLOT TUNE BAR EJECT BUTTON PWR/VOL KNOB You can also play 3-inch (8-cm) discs without using an adapter ring.
Main Menu Table of Contents Audio System When the system reaches the end of the disc, it will return to the beginning and play that disc again. You can switch to the radio while a CD is playing by pressing the A M / FM button. Press the CD button to return to playing the CD. The CD will begin playing where it left off. If you turn the system off while a CD is playing, either with the PWR/VOL knob or by turning off the ignition, the disc will stay in the drive.
Main Menu Table of Contents Audio System REPEAT — To activate the Repeat feature, press and release the RPT button. You will see RPT in the display. The system continuously replays the current track. Press the RPT button again to turn it off. RANDOM PLAY — This feature, when activated, plays the tracks on the CD in random order, rather than in the order they are recorded on the CD. To activate Random Play, press and release the A. SEL/RDM button. You will see RDM in the display.
Main Menu Table of Contents Audio System Operating the CD Changer (Optional) A Compact Disc changer is available for your vehicle. It holds up to six discs, providing several hours of continuous entertainment. You operate this CD changer with the same controls used for the in-dash CD player. Load the desired CDs in the magazine and load the magazine in the changer according to the instructions that came with the unit. Play only standard round discs.
Main Menu Table of Contents Audio System Protecting Compact Discs Handle a CD by its edges: never touch either surface. Contamination from fingerprints, liquids, felt-tip pens, and labels can cause the CD to not play properly, or possibly jam in the drive. When a CD is not being played, store it in its case to protect it from dust and other contamination. To prevent warpage, keep CDs out of direct sunlight and extreme heat. To clean a disc, use a clean soft cloth.
Main Menu Table of Contents Audio System Never try to insert foreign objects in the CD player or the magazine. A new CD may be rough on the inner and outer edges. The small plastic pieces causing this roughness can flake off and fall on the recording surface of the disc, causing skipping or other problems. Remove these pieces by rubbing the inner and outer edges with the side of a pencil or pen.
Main Menu Table of Contents Audio System CD Player Error Indications If you see an error indication in the display while operating the CD player, find the cause in the chart to the right. If you cannot clear the error indication, take the vehicle to your Honda dealer.
Main Menu Table of Contents Audio System CD Changer Error Indications If you see an error indication in the display while operating the CD changer, find the cause in the chart to the right. If you cannot clear the error indication, take the vehicle to your Honda dealer.
Main Menu Table of Contents Audio System Remote Audio Controls AUDIO CONTROL BUTTON CHANNEL BUTTON MUTE BUTTON VOLUME LEVER Four controls for the audio system are on the left side of the dashboard by the instrument panel. These let you control basic functions without distracting your attention from driving. Use the VOLUME lever to adjust the volume. Push the lever up to increase the volume and down to decrease it. Hold the lever until the volume reaches the desired level, then release it.
Main Menu Table of Contents Audio System Theft Protection Your car's audio system will disable itself if it is disconnected from electrical power for any reason. To make it work again, the user must enter a specific five-digit code in the Preset buttons. Because there are hundreds of number combinations possible from five digits, making the system work without knowing the exact code is nearly impossible. You should have received a card that lists your audio system's code number and serial number.
Main Menu Before Driving Before you begin driving your Honda, you should know what gasoline to use, and how to check the levels of important fluids. You also need to know how to properly store luggage or packages. The information in this section will help you. If you plan to add any accessories to your vehicle, please read the information in this section first. Break-in Period.............................. 116 Gasoline......................................... . 116 Service Station Procedures ..........
Main Menu Table of Contents Break-in Period, Gasoline Break-in Period Help assure your car's future reliability and performance by paying extra attention to how you drive during the first 600 miles (1,000 km). During this period: Avoid full-throttle starts and rapid acceleration. Do not exceed 5,500 rpm for the first 600 miles (1,000 km) of operation. Avoid hard braking. New brakes need to be broken-in by moderate use for the first 200 miles (300 km).
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Service Station Procedures Filling the Fuel Tank Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. Stop the engine and keep heat, sparks, and flame away. Handle fuel only outdoors. Wipe up spills immediately. FUEL FILL CAP 1. Because the fuel fill cap is on the driver's side of the car, park with that side closest to the service station pumps. 2.
Main Menu Table of Contents Service Station Procedures 4. Stop filling the tank after the fuel nozzle automatically clicks off. Do not try to "top off" the tank, leave some room for the fuel to expand with temperature changes. Opening the Hood RELEASE HANDLE 5. Screw the fuel fill cap back on, tighten it until it clicks several times. If you do not properly tighten the cap, the Malfunction Indicator Lamp may come on (see page 230). 6. Push the fuel fill door closed until it latches. 1.
Main Menu Table of Contents Service Station Procedures Oil Check DIPSTICK 3. Pull the support rod out of its clip and insert the end into the hole on the front of the hood around the center. To close the hood, lift it up slightly to remove the support rod from the hole. Put the support rod back into its holding clip. Lower the hood to about a foot (30 cm) above the fender, then let it drop. After closing the hood, make sure it is securely latched.
Main Menu Table of Contents Service Station Procedures Engine Coolant Check UPPER MARK LOWER MARK 3. Insert it all the way back in its tube. 4. Remove the dipstick again and check the level. It should be between the upper and lower marks. If it is near or below the lower mark, see Adding Oil on page 157. Look at the coolant level in the radiator reserve tank. Make sure it is between the MAX and M IN lines.
Main Menu Table of Contents Fuel Economy The condition of your car and your driving habits are the two most important things that affect the fuel mileage you get. Car Condition Always maintain your car according to the maintenance schedule. This will keep it in top operating condition. An important part of that maintenance is the Owner Maintenance Checks (see page 155 ). For example, an underinflated tire causes more "rolling resistance," which uses fuel.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Accessories and Modifications Modifying your car, or installing some non-Honda accessories, can make your car unsafe. Before you make any modifications or add any accessories, be sure to read the following information. Accessories Your dealer has Genuine Honda accessories that allow you to personalize your car. These accessories have been designed and approved for your car, and are covered by warranty.
Main Menu Table of Contents Accessories and Modifications Modifications Do not remove any original equipment or modify your car in any way that would alter its design or operation. This could make your car unsafe and illegal to drive. In addition, any modifications that decrease ground clearance increase the chance of undercarriage parts striking a curb, speed bump, or other raised object, which could cause your airbags to deploy.
Main Menu Table of Contents Carrying Cargo UPPER AND LOWER CONSOLE COMPARTMENTS Your car has several convenient storage areas so you can stow cargo safely. The upper and lower console compartments are designed for small, lightweight items. The trunk is intended for larger, heavier items. However, carrying too much cargo, or improperly storing it, can affect your car's handling, stability and operation and make it unsafe. Before carrying any type of cargo, be sure to read the following pages.
Main Menu Table of Contents０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Carrying Cargo Load Limit The maximum load for your car is 400 1bs (185kg). This figure includes the total weight of all occupants, cargo, and accessories. To figure out how much cargo you can cany: Add up the weight of all occupants. Overloading or improper loading can affect handling and stability and cause a crash in which you can be hurt or killed. Follow all load limits and other loading guidelines in this manual.
Main Menu Table of Contents Carrying Cargo Carrying Cargo in the Trunk Distribute cargo evenly on the floor of the trunk, placing the heaviest items on the bottom and as far forward as possible.
Main Menu Table of Contents General Precautions Your Honda is designed to give you optimum handling and performance on well-maintained roads. As part of this design, your car has a minimum of ground clearance and very lowprofile tires. Use caution if you should drive your car on very rough or rutted roads. You could damage the suspension and underbody by bottoming out. Going too fast over parking lot "speed bumps" can also cause damage.
Main Menu 128
Main Menu Driving This section gives you tips on starting the engine under various conditions, and how to operate the manual transmission. It also includes important information on parking your car, and the braking system. Preparing to Drive......................... 130 Starting the Engine........................ 131 Starting in Cold Weather at High Altitude ..................... 132 6-speed Manual Transmission..... 133 Recommended Shift Points...... 134 Engine Speed Limiter ...............
Main Menu Table of Contents Preparing to Drive You should do the following checks and adjustments every day before you drive your car. 1. Make sure all windows, mirrors, and outside lights are clean and unobstructed. Remove frost, snow, or ice. 2. Check that the hood and trunk are fully closed. 3. Visually check the tires. If a tire looks low, use a gauge to check its pressure. Driving 4. Check that any items you may be carrying with you inside are stored properly or fastened down securely. 5.
Main Menu Table of Contents Starting the Engine 1. Apply the parking brake. 6. If the engine does not start within 15 seconds, or starts but stalls right away, repeat step 5 with the accelerator pedal pressed half-way down. If the engine starts, release pressure on the accelerator pedal so the engine does not race. 2. In cold weather, turn off all electrical accessories to reduce the drain on the battery. 3. Push the clutch pedal down all the way.
Main Menu Table of Contents Starting the Engine Starting in Cold Weather at High Altitude (Above 8,000 feet/ 2,400 meters) An engine is harder to start in cold weather. The thinner air found at high altitude above 8,000 feet (2,400 meters) adds to the problem. Use the following procedure: 1. Turn off all electrical accessories to reduce the drain on the battery. 2. Push the accelerator pedal halfway to the floor and hold it there while starting the engine.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２ 6-speed Manual Transmission Come to a full stop before you shift into Reverse. You can damage the transmission by trying to shift into Reverse with the car moving. Push down the clutch pedal, and pause for a few seconds before shifting into Reverse, or shift into one of the forward gears for a moment. This stops the gears so they won't "grind." The manual transmission is synchronized in all forward gears for smooth operation.
Main Menu Table of Contents 6-speed Manual Transmission Recommended Shift Points Drive in the highest gear that lets the engine run and accelerate smoothly. This will give you the best fuel economy and effective emissions control. The following shift points are recommended: Engine Speed Limiter If you exceed the maximum speed for the gear you are in, the engine speed will enter into the tachometer's red zone.
Main Menu Table of Contents Parking Always use the parking brake when you park your car. The indicator on the instrument panel shows that the parking brake is not fully released; it does not indicate that the parking brake is firmly set. Make sure the parking brake is set firmly or your car may roll if it is parked on an incline. If the car is facing uphill, turn the front wheels away from the curb and put the transmission in first gear.
Main Menu Table of Contents The Braking System Your Honda is equipped with disc brakes at all four wheels. A power assist helps reduce the effort needed on the brake pedal. The ABS helps you retain steering control when braking very hard. Put your foot on the brake pedal only when you intend to brake. Resting your foot on the pedal keeps the brakes applied lightly, causing them to build up heat. Heat build-up can reduce how well your brakes work.
Main Menu Table of Contents The Braking System Brake System Design The hydraulic system that operates the brakes has two separate circuits. Each circuit works diagonally across the car (the left-front brake is connected with the right-rear brake, etc.). If one circuit should develop a problem, you will still have braking at two wheels. Anti-lock Brakes Your car has an Anti-lock Brake System (ABS) as standard equipment.
Main Menu Table of Contents The Braking System You should never pump the brake pedal, this defeats the purpose of the ABS. Let the ABS work for you by always keeping firm, steady pressure on the brake pedal as you steer away from the hazard. This is sometimes referred to as "stomp and steer." You will feel a pulsation in the brake pedal when the ABS activates, and you may hear some noise. This is normal, it is the ABS rapidly pumping the brakes.
Main Menu Table of Contents The Braking System ABS Indicator PUSH CANCEL ANTI-LOCK BRAKE SYSTEM INDICATOR* * U.S. indicator shown The ABS is self-checking. If anything goes wrong, the ABS indicator on the instrument panel comes on (see page 45). This means the anti-lock function of the braking system has shut down. The brakes still work like a conventional system without antilock, providing normal stopping ability. You should have the dealer inspect your car as soon as possible.
Main Menu Table of Contents Driving in Bad Weather Rain, fog, and snow conditions require a different driving technique because of reduced traction and visibility. Keep your car wellmaintained and exercise greater caution when you need to drive in bad weather. The cruise control should not be used in these conditions. Driving Driving Technique — Always drive slower than you would in dry weather. It takes your car longer to react, even in conditions that may seem just barely damp.
Main Menu Table of Contents Driving in Bad Weather, Towing a Trailer Towing a Trailer Your car is not designed to tow a trailer. Attempting to do so can void your warranties. Traction — Check your tires frequently for wear and proper pressure. Both are important in preventing "hydroplaning" (loss of traction on a wet surface). In the winter, mount snow tires on all four wheels for the best handling. Watch road conditions carefully, they can change from moment to moment.
Main Menu 142
Main Menu Maintenance This section explains why it is important to keep your car well maintained and to follow basic maintenance safety precautions. This section also includes Maintenance Schedules for normal driving and severe driving conditions, a Maintenance Record, and instructions for simple maintenance tasks you may want to take care of yourself. If you have the skills and tools to perform more complex maintenance tasks on your Honda, you may want to purchase the Service Manual.
Main Menu Table of Contents Maintenance Safety Regularly maintaining your car is the Some of the most important safety This section includes instructions for best way to protect your investment. precautions are given here. However, simple maintenance tasks, such as Proper１６：１１：０９ maintenance is essential to we cannot warn you of every checking and adding oil.
Main Menu Table of Contents Maintenance Safety Important Safety Precautions Before you begin any maintenance, make sure your car is parked on level ground and that the parking brake is set. Also, be sure the engine is off. This will help to eliminate several potential hazards: Carbon monoxide poisoning from engine exhaust. Be sure there is adequate ventilation whenever you operate the engine. Burns from hot parts. Let the engine and exhaust system cool before touching any parts. Injury from moving parts.
Main Menu Table of Contents Maintenance Schedule The Maintenance Schedule specifies how often you should have your car serviced and what things need attention. It is essential that you have your car serviced as scheduled to retain its high level of safety, dependability, and emissions control performance. The services and time or distance intervals shown in the maintenance schedule assume you will use your car as normal transportation for your passenger and possessions.
Main Menu Table of Contents Maintenance Schedule Your authorized Honda dealer knows your car best and can provide competent, efficient service. However, service at a dealer is not mandatory to keep your warranties in effect. Maintenance may be done by any qualified service facility or person who is skilled in this type of automotive service. Keep all the receipts as proof of completion, and have the person who does the work fill out the Maintenance Record. Check your warranty booklet for more information.
Main Menu Table of Contents U.S. Owners Follow the Normal Conditions Maintenance Schedule if the severe driving conditions specified in the Severe Conditions Maintenance Schedule do not apply. NOTE: If you only OCCASIONALLY drive under a "severe" condition, you should follow the Normal Conditions Maintenance Schedule. Canadian Owners Follow the Maintenance Schedule for Severe Conditions. # : See information on maintenance and emissions warranty, last column, page 147 .
Main Menu Table of Contents Service at the indicated distance or time, whichever comes first. Do the items in A, B, C, D as required for each distance/time interval. U.S. Owners — Refer to page 148 to determine which schedule to use. Canadian owners: Follow the schedule for Severe Conditions. # : See information on maintenance and emissions warranty, last column, page 147. Note: Check engine oil and coolant at each fuel stop. Check and adjust valve clearance, cold engine, only if noisy.
Main Menu Table of Contents U.S. Owners Follow the Severe Conditions Maintenance Schedule if you drive your vehicle MAINLY under one or more of the following conditions: Driving less than 5 miles (8 km) per trip or, in freezing temperatures, driving less than 10 miles (16 km) per trip. Driving in extremely hot [over 90°F (32° Q] conditions. Extensive idling or long periods of stop-and-go driving. Driving in mountainous conditions. Driving on muddy, dusty, or de-iced roads.
Main Menu Table of Contents Service at the indicated distance or time, whichever comes first. Do the items in A, B, C, D, E, F as required for each distance/time. U.S. Owners — Refer to page 150 to determine which schedule to use. Canadian Owners — Use the Maintenance Schedule for Severe Conditions. Air Conditioning Filter on page 183 for replacement information under special driving *1 : See conditions. # : See information on maintenance and emissions warranty, last column, page 147.
Main Menu Table of Contents Air Conditioning Filter on page 183 for replacement *1 : See information under special driving conditions. # : See information on maintenance and emissions warranty, last column, page 147. NOTE: Check engine oil and coolant at each fuel stop. Check and adjust valve clearance, cold engine, only if noisy.
Main Menu Table of Contents Required Maintenance Record (for Normal and Severe Schedules) You or the servicing dealer can record all completed maintenance here, whether you follow the schedule for normal conditions (page 148) or severe conditions (page 150). Keep the receipts for all work done on your vehicle.
Main Menu Table of Contents Required Maintenance Record (for Normal and Severe Schedules) Maintenance
Main Menu Table of Contents Owner Maintenance Checks You should check the following items at the specified intervals. If you are unsure of how to perform any check, turn to the page given. Engine oil level — Check every time you fill the fuel tank. See page 119. Engine coolant level — Check the radiator reserve tank every time you fill the fuel tank. See page 120. Windshield washer fluid — Check the level in the reservoir monthly.
Main Menu Table of Contents Fluid Locations ENGINE OIL FILL CAP WASHER FLUID (Blue cap) CLUTCH FLUID (Gray cap) BRAKE FLUID (Gray cap) ENGINE OIL DIPSTICK COOLANT RESERVOIR Maintenance
Main Menu Table of Contents Engine Oil Adding Oil To add oil, unscrew and remove the engine oil fill cap on top of the left valve cover. Pour in the oil, and replace the engine oil fill cap. Tighten it securely. Wait a few minutes and recheck the oil level. Do not fill above the upper mark; you could damage the engine. Recommended Oil Oil is major contributor to your engine's performance and longevity. Always use a premium-grade detergent oil displaying the API Certification Seal.
Main Menu Table of Contents Engine Oil The numbers on the container's label tell you the oil's viscosity or weight. Select the oil for your car according to this chart. Ambient Temperature An oil with a viscosity of 10W-30 is preferred for optimum fuel economy and year-round protection in your Honda. You may use a 5W-40 oil if the temperature in your area goes below 0 ° F ( - 20° C).
Main Menu Table of Contents Engine Oil Changing the Oil and Filter Always change the oil and filter according to the time and distance (miles/kilometers) recommendations in the maintenance schedule. The oil and filter collect contaminants that can damage your engine if they are not removed regularly. Changing the oil and filter requires special tools and access from underneath the car. The car should be raised on a service station-type hydraulic lift for this service.
Main Menu Table of Contents Engine Oil 5. Put a new washer on the drain bolt, then reinstall the drain bolt. Tighten it to: 33 lbf.ft (45 N.m, 4.6 kgf.m) 6. Refill the engine with the recommended oil. Engine oil change capacity (including filter): 5.1 US qt (4.8 , 4.2 Imp qt) 7. Replace the engine oil fill cap. Start the engine. The oil pressure indicator light should go out within five seconds. If it does not, turn off the engine and reinspect your work. 8.
Main Menu Table of Contents Cooling System ０３／０７／１０ Adding Engine Coolant Always use Honda All Season Antifreeze/Coolant Type 2. This coolant is pre-mixed with 50 percent antifreeze and 50 percent water. It does not require any additional mixing. RESERVE TANK M AX M IN If the coolant level in the reserve tank is at or below the MIN line, add coolant to bring it up to the MAX line. Inspect the cooling system for leaks.
Main Menu Table of Contents Cooling System RADIATOR CAP 2. Turn the radiator cap counterclockwise, without pressing down on it, until it stops. This relieves any pressure remaining in the cooling system. 3. Remove the radiator cap by pushing down and turning counterclockwise. Maintenance RESERVE TANK 4. The coolant level should be up to the base of the filler neck. Add coolant if it is low. 5. Put the radiator cap back on. Tighten it fully. 6. Pour coolant into the reserve tank.
Main Menu Table of Contents Cooling System Replacing Engine Coolant The cooling system should be completely drained and refilled with new coolant according to the time and distance recommendations in the maintenance schedule. Only use Honda All season Antifreeze/ Coolant Type 2. Draining the coolant requires access to the underside of the vehicle. Unless you have the tools and knowledge, you should have this maintenance done by a skilled mechanic. DRAIN BOLT DRAIN PLUG 1. Turn the ignition ON (II).
Main Menu Table of Contents Cooling System RESERVE TANK CAP HOLDER BLEEDER BOLT RESERVE TANK 5. Remove the reserve tank from its holder by pulling it straight up. Drain the coolant, then put the tank back in its holder. Maintenance 6. When the coolant stops draining, tighten the drain plug at the bottom of the radiator. Apply non-hardening sealant to the drain bolt threads, put a new washer on the drain bolt, and reinstall the bolt in the engine block. Tighten it securely. Tightening torque: 61 lbf.
Main Menu Table of Contents Cooling System BLEEDER CAP Fill up to here RESERVE TANK FILLER NECK 8. Pour Honda All Season Antifreeze/Coolant Type 2 into the radiator up to the base of the filler neck. This coolant is a mixture of 50 percent antifreeze and 50 percent water. Pre-mixing is not required. The cooling system capacity is: 1.72 US gal (6.5 , 1.43 Imp gal) 9. Tighten the bleeder bolt and reinstall the bleeder cap when coolant comes out in a steady stream with no bubbles. 10.
Main Menu Table of Contents Cooling System 15. Remove the radiator cap. 16. Pour coolant into the radiator up to the base of the filler neck and into the reserve tank up to the MAX mark. 17. Start the engine and hold it at 1,500 rpm until the radiator fan comes on. Turn off the engine. Check the coolant level in the radiator and add coolant if needed. 18. Install the radiator cap, and tighten it fully. 19. If necessary, fill the reserve tank to the MAX mark. Install the reserve tank cap.
Main Menu Table of Contents Windshield Washers RESERVOIR CAP Check the reservoir's fluid level by removing the cap and looking at the level gauge attached to the cap. Fill the reservoir with a good-quality windshield washer fluid. This increases the cleaning capability and prevents freezing in cold weather. When you refill the reservoir, clean the edges of the windshield wiper blades with windshield washer fluid on a clean cloth. This will help to condition the blade edges.
Main Menu Table of Contents 6-speed Manual Transmission Fluid FILLER BOLT CORRECT LEVEL Check the fluid level with the transmission at normal operating temperature and the car sitting on level ground. Remove the transmission filler bolt and carefully feel inside the bolt hole with your finger. The fluid level should be up to the edge of the bolt hole. If it is not, add Honda Manual Transmission Fluid (MTF) until it starts to run out of the hole. Reinstall the filler bolt and tighten it securely.
Main Menu Table of Contents Differential Fluid Use a SAE 90 viscosity hypoid gear oil, API service classified GL5 or GL6 only, in the differential. FILLER BOLT Put a new washer on the filler bolt, then reinstall the filler bolt. Tighten it securely. Tightening torque: 33 lbf.ft (45N.m , 4.6 kgf.m) CORRECT LEVEL Check the fluid level with the differential at normal operating temperature and the vehicle sitting on level ground.
Main Menu Table of Contents Brake and Clutch Fluid Check the fluid level in the reservoirs monthly. There are two reservoirs. They are: Brake fluid reservoir Clutch fluid reservoir The brake fluid should be replaced according to the time recommendation in the maintenance schedule. Maintenance Brake Fluid Always use Honda Heavy Duty Brake Fluid DOT 3. If it is not available, you should use only DOT 3 or DOT 4 fluid, from a sealed container, as a temporary replacement.
Main Menu Table of Contents Clutch Fluid Clutch System M AX M IN The fluid should be between the MIN and MAX marks on the side of the reservoir. If it is not, add brake fluid to bring it up to that level. Use the same fluid specified for the brake system. Low fluid level can indicate a leak in the clutch system. Have this system inspected as soon as possible.
Main Menu Table of Contents Air Cleaner Element The air cleaner element should be replaced according to the time and distance recommendations in the maintenance schedule. Replacement CLAMPS AIR CLEANER ELEMENT Follow the replacement procedure for removal and reinstallation. To replace it: 1. Unsnap the six clamps holding the air cleaner housing cover. 2. Remove the air cleaner housing cover. Disconnect the air intake duct from the air cleaner element. Maintenance 3.
Main Menu Table of Contents Air Cleaner Element 5. Attach the new air cleaner element to the duct. Install the new air cleaner element in the air cleaner housing. Make sure the pin on the edge of the element fits in the hole in the bottom of the housing. 6. Reinstall the air cleaner housing cover, snap the six clamps back into place.
Main Menu Table of Contents Hood Latch, Spark Plugs Hood Latch PIVOTS Clean the hood latch assembly with a mild cleaner, then lubricate it with a multipurpose grease. Lubricate all the moving parts, including the pivot. Follow the time and distance recommendations in the Maintenance Schedule. If you are not sure how to clean and grease the latch, contact your Honda dealer. Maintenance Spark Plugs The spark plugs in your car are a special platinum-tipped design for longer life.
Main Menu Table of Contents Spark Plugs 3. Remove the bolt holding the ignition coil and pull the ignition coil straight up slightly. Disconnect the ignition coil connector by pushing the tab and pulling the connector back. Pull the ignition coil all the way up. 5. Put the new spark plug into the socket; then screw it into the hole. Screw it in by hand so you do not crossthread it. 6. Torque the spark plug.
Main Menu Table of Contents Spark Plugs NOTICE Tighten the spark plugs carefully. A spark plug that is too loose can overheat and damage the engine. Overtighlening can cause damage to the threads in the cylinder head. 7. Install the ignition coil. Reinstall the bolt. 8. Repeat this procedure for the other three spark plugs. 9. Reinstall the cover on the cylinder bank. Reinstall the four hexagon socket head cap bolts. Maintenance Specifications: NGK: DENSO: PFR7G-11S PK22PR-L11S Spark Plug Gap: 0.
Main Menu Table of Contents Battery Check the condition of your car's battery monthly. You should check the color of the test indicator window, and for corrosion on the terminals. Check the battery terminals for corrosion (a white or yellowish powder). To remove it, cover the terminals with a solution of baking soda and water. It will bubble up and turn brown. When this stops, wash it off with plain water. Dry off the battery with a cloth or paper towel.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ Battery If you need to connect the battery to a charger, disconnect both cables to prevent damage to the car's electrical system. The battery gives off explosive hydrogen gas during normal operation. A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you. If the terminals are severely corroded, clean them with baking soda and water. Then use a wrench to loosen and remove the cables from the terminals.
Main Menu Table of Contents Battery If your car's battery is disconnected or goes dead, the audio system will disable itself. The next time you turn on the radio you will see "Code" in the frequency display. Use the Preset buttons to enter the five-digit code (see page 114). NOTICE Charging the battery with the cables connected can seriously damage your car's electronic controls. Detach the battery cables before connecting the battery to a charger.
Main Menu Table of Contents Wiper Blades Check the condition of the wiper blades at least every six months. Look for signs of cracking in the rubber, or areas that are getting hard. Replace the blades if you find these signs, or they leave streaks and unwiped areas when used. LOCK TAB To replace the blade: 1. Raise the wiper arm off the windshield. Maintenance 2. Disconnect the blade assembly from the wiper arm by pushing in the lock tab.
Main Menu Table of Contents Wiper Blades BLADE 5. Slide the new wiper blade into the holder until the tabs lock. 6. Slide the wiper blade assembly onto the wiper arm. Make sure it locks in place. 7. Lower the wiper arm down against the windshield. REINFORCEMENT 3. Remove the blade from its holder by grasping the tabbed end of the blade. Pull firmly until the tabs come out of the holder. 4. Examine the new wiper blades.
Main Menu Table of Contents Air Conditioning System If the air conditioning does not get as cold as before, have your dealer check the system. Recharge the system with Refrigerant HFC-134a (R-134a). (See Specifications on page 247.) Your car's air conditioning is a sealed system. Any major maintenance, such as recharging, should be done by a qualified mechanic. You can do a couple of things to make sure the air conditioning works efficiently.
Main Menu Table of Contents Air Conditioning Filter The air conditioning filter removes pollen and dust from outside air the heating and cooling system brings into the interior. It should be replaced according to the lime and distance recommendations in the maintenance schedule. This filter should be replaced every 30,000 miles (48,000 km) under normal conditions.
Main Menu Table of Contents Drive Belt Auto-tensioner INDICATOR You should check the condition of the drive belt every 2 years. Examine the edges of belt for cracks or fraying. Maintenance AUTOTENSIONER POINTER An auto-tensioner adjusts the tension of the drive belt. The pointer on the auto-tensioner should be between the two lines of the indicator. If the pointer is not between the lines, contact your Honda dealer.
Main Menu Table of Contents０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Tires To safely operate your car, your tires must be the proper type and size, in good condition with adequate tread, and correctly inflated. The following pages give more detailed information on how and when to check air pressure, how to inspect your tires for damage and wear, and what to do when your tires need to be replaced.
Main Menu Table of Contents Tires Use a gauge to measure the air pressure at least once a month. Even tires that are in good condition may lose one to two psi (10 to 20 kPa, 0.1 to 0.2 kgf/cm2 ) per month. Remember to check the spare tire at the same time you check all the other tires. Check the pressure in the tires when they are cold. This means the car has been parked for at least three hours.
Main Menu Table of Contents Tires Tubeless tires have some ability to self-seal if they are punctured. However, because leakage is often very slow, you should look closely for punctures if a tire starts losing pressure. Inspection Every time you check inflation, you should also examine the tires for damage, foreign objects, and wear. You should look for: INDICATOR LOCATION MARKS Bumps or bulges in the tread or side of the tire. Replace the tire if you find either of these conditions.
Main Menu Table of Contents Tires Maintenance In addition to proper inflation, correct wheel alignment helps to decrease tire wear. If you find a tire is worn unevenly, have your dealer check the wheel alignment. The tires were properly balanced by the factory. They may need to be rebalanced at some time before they are worn out. Have your dealer check the tires if you feel a consistent vibration while driving. A tire should always be rebalanced if it is removed from the wheel for repair.
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ Tires You should carefully inspect your car's tires for wear, damage, and proper inflation every 7,500 miles (12,000km) (see page 185). Replacing Tires and Wheels The tires that came with your car were selected to match the performance capabilities of the car while providing the best combination of handling, ride comfort, and long life.
Main Menu Table of Contents Tires The ABS works by comparing the speed of the wheels. When replacing tires, use the same size originally supplied with the car. Tire size and construction can affect wheel speed and may cause the system to work inconsistently. If you ever need to replace a wheel, make sure the wheel's specifications match those of the original wheel that came on your car. Replacement wheels are available at your Honda dealer.
Main Menu Table of Contents Tires Snow Tires If you mount snow tires on your Honda, make sure they are radial tires of the same size and load range as the original tires. Mount snow tires on all four wheels to balance your vehicle's handling in all weather conditions. Keep in mind the traction provided by snow tires on dry roads may not be as high as your vehicle's original equipment tires. You should drive cautiously even when the roads are clear.
Main Menu Table of Contents Lights Check the operation of your car's exterior lights at least once a month. A burned out bulb can create an unsafe condition by reducing your car's visibility and the ability to signal your intentions to other drivers.
Main Menu Table of Contents Lights Check the following: Headlights (low and high beam) Parking lights Taillights Brake lights Turn signals Back-up lights Hazard light function License plate light Side marker lights Daytime running lights (Canadian cars) TURN SIGNAL LIGHT If you find any bulbs are burned out, replace them as soon as possible. Refer to the chart on page 247 to determine what type of replacement bulb is needed.
Main Menu Table of Contents Lights Replacing a Headlight Bulb The low beam headlight bulbs are a type of high voltage discharge tube. High voltage can remain in the circuit even with the light switch off and the key removed. Because of this, you should not attempt to examine or change a low beam headlight bulb yourself. If a low beam headlight bulb fails, take the car to your dealer to have it replaced. Maintenance Halogen bulbs are used for the high beam headlight bulbs.
Main Menu Table of Contents Lights 6. Insert the socket back into the headlight assembly. Make sure the bulb is installed correctly by looking through the headlight lens. The pins on the base of the bulb should fit in the holes in the headlight assembly. Pivot the holddown wire back in place and clip the end into the slot. 1. Open the hood. If you need to change the high beam headlight bulb on the left side, remove the coolant reserve tank from its holder by pulling it straight up. 2.
Main Menu Table of Contents Lights Replacing Front Turn Signal and Side Marker Light Bulbs 1. If you are changing the bulb on the driver's side, start the engine, turn the steering wheel all the way to the right, and turn off the engine. If you are changing the bulb on the passenger's side, turn the steering wheel to the left. 2. Use a flat-tipped screwdriver to remove the three holding clips from the inner fender. 3. Pull the inner fender cover back. 4.
Main Menu Table of Contents Lights Replacing a Side Turn Signal Bulb 3. Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms. 4. Put the bulb holder back into its hole in the lens, and turn it clockwise until it locks. 5. Test the lights to make sure the new bulb is working. 1. Use a small flat blade screwdriver to pry carefully on the back edge of the side turn signal assembly until it pops out of the body. 2.
Main Menu Table of Contents Lights Replacing Rear Bulbs 1. Open the trunk. 2. Remove the fasteners from the trunk lining. To remove a fastener, push on the center of the head until it pops in. Then pull it out. 3. Pull the lining back. Maintenance 4. Determine which of the four bulbs is burned out: stop/taillight, backup light, turn signal, or side marker. 5. Remove the socket by turning it one-quarter turn counterclockwise. 6. Remove the burned out bulb.
Main Menu Table of Contents Lights 7. Install the new bulb in the socket. 8. Push the socket into the light assembly and turn it clockwise until it locks. 9. Test the lights to make sure the new bulb is working. 10. Install the trunk lining and secure it with the fasteners. To reinstall a fastener, reset the fastener by pushing on the pointed end until it pops back almost flush with the fingers on the housing.
Main Menu Table of Contents Lights Replacing a Rear License Plate Bulb 1. Insert a flat blade screwdriver between the left edge of the lens and the housing. The lens will come down. 2. Pull the bulb straight out of its socket. Push the new bulb in until it bottoms in the socket. 3. Test the lights to make sure the new bulb is working. 4. Put the lens back into the light assembly, right side first. Push on the left edge until it snaps into place.
Main Menu Table of Contents Lights Replacing an Interior Light Bulb 1. Remove the lens by carefully prying on the front edge of the lens near both sides. Replacing the Trunk Light Bulb 2. Remove the bulb by pulling it straight out of its metal tabs. 1. Open the trunk. Pull down the trunk light cover. 3. Push the new bulb into the metal tabs. Snap the lens back in place. 2. Remove the bulb by pulling it straight out of its metal tabs. 3. Push the new bulb into the metal tabs. 4.
Main Menu Table of Contents Storing Your Car If you need to park your car for an extended period (more than one month), there are several things you should do to prepare it for storage. Proper preparation helps prevent deterioration and makes it easier to get your car back on the road. If possible, store your car indoors. Fill the fuel tank. Change the engine oil and filter (see page 159). Wash and dry the exterior completely. Clean the interior. Make sure the carpeting, floor mats, etc.
Main Menu Appearance Care Regular cleaning and polishing of your Honda helps to keep it "new" looking. This section gives you hints on how to clean your car and preserve its appearance: the paint, brightwork, wheels and interior. Also included are several things you can do to help prevent corrosion. Exterior Care.................................. 204 Washing..................................... . 204 Waxing.......................................205 Aluminum Wheels..................... 206 Paint Touch-up..
Main Menu Table of Contents Exterior Care Washing Frequent washing helps preserve your car's beauty. Dirt and grit can scratch the paint, while tree sap and bird droppings can permanently ruin the finish. Wash your car in a shady area, not in direct sunlight. If the car is parked in the sun, move it into the shade and let the exterior cool down before you start. Only use the solvents and cleaners recommended in this Owner's Manual.
Main Menu Table of Contents Exterior Care Waxing Always wash and dry the whole car before waxing it. You should wax your car, including the metal trim, whenever water sits on the surface in large patches. It should form into beads or droplets after waxing. You should use a quality liquid or paste wax. Apply it according to the instructions on the container. In general, there are two types of products: Waxes — A wax coats the finish and protects it from damage by exposure to sunlight, air pollution, etc.
Main Menu Table of Contents Exterior Care Aluminum Wheels Clean your Acura's aluminum alloy wheels as you do the rest of the exterior. Wash them with the same solution, and rinse them thoroughly. The wheels have a protective clearcoat that keeps the aluminum from corroding and tarnishing. Using harsh chemicals, including some commercial wheel cleaners, or stiff brushes can damage this clear-coat. Only use a mild detergent and soft brush or sponge to clean the wheels.
Main Menu Table of Contents Interior Care Carpeting Vacuum the carpeting frequently to remove dirt. Ground-in dirt will make the carpet wear out faster. Periodically shampoo the carpet to keep it looking new. Use one of the foam-type carpet cleaners on the market. Follow the instructions that come with the cleaner, applying it with a sponge or soft brush. Keep the carpeting as dry as possible by not adding water to the foam.
Main Menu Table of Contents Interior Care Fabric Vacuum dirt and dust out of the material frequently. For general cleaning, use a solution of mild soap and lukewarm water, letting it air dry. To clean off stubborn spots, use a commercially-available fabric cleaner. Test it on a hidden area of the fabric first, to make sure it does not bleach or stain the fabric. Follow the instructions that come with the cleaner. Appearance Care Vinyl Remove dirt and dust with a vacuum cleaner.
Main Menu Table of Contents Interior Care, Corrosion Protection Windows Clean the windows, inside and out, with a commercially-available glass cleaner. You can also use a mixture of one part white vinegar to ten parts water. This will remove the haze that builds up on the inside of the windows. Use a soft cloth or paper towels to clean all glass and clear plastic surfaces. Air Fresheners If you want to use an air freshener/ deodorizer in the interior of your car, it is best to use a solid type.
Main Menu Table of Contents Corrosion Protection Many corrosion-preventive measures are built into your Honda. You can help keep your car from corroding by performing some simple periodic maintenance: Repair chips and scratches in the paint as soon as you discover them. Inspect and clean out the drain holes in the bottom of the doors and body. Check the floor coverings for dampness. Carpeting and floor mats may remain damp for a long time, especially in winter.
Main Menu Table of Contents Body Repairs Body repairs can affect your car's resistance to corrosion. If your car needs repairs after a collision, pay close attention to the parts used in the repair and the quality of the work. Make sure the repair facility uses genuine Honda replacement body parts. Some companies make sheet metal pieces that seem to duplicate the original Honda body parts, but are actually inferior in fit, finish, and corrosion resistance.
Main Menu 212
Main Menu Taking Care of the Unexpected This section covers the morecommon problems that motorists experience with their vehicles. It gives you information about how to safely evaluate the problem and what to do to correct it. If the problem has stranded you on the side of the road, you may be able to get going again. If not, you will also find instructions on getting your car towed. Compact Spare Tire....................... 214 Changing a Flat Tire ..................... 215 If Your Engine Won't Start....
Main Menu Table of Contents Compact Spare Tire Your car has a compact spare tire that takes up less space. Use this spare tire as a temporary replacement only. Get your regular tire repaired or replaced and put it back on your car as soon as you can. Check the inflation pressure of the compact spare tire every time you check the other tires. It should be inflated to: 60 psi (420 kPa , 4.
Main Menu Table of Contents Changing a Flat Tire The size difference may also cause If you have a flat tire while driving, damage to the rear differential, so do stop in a safe place to change it. not mount the compact spare on the Stopping in traffic or on the shoulder ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ rear. If either rear tire goes flat, of a busy road is dangerous.
Main Menu Table of Contents Changing a Flat Tire 4. Remove the three clips holding the spare tire cover by pulling straight up on the rings. Remove the spare tire cover. Taking Care of the Unexpected 5. Unscrew the wing bolt and take the spare tire out of the spare tire shelf. 6. Loosen the five wheel nuts 1/2 turn with the wheel wrench. 7. Locate the jacking point nearest the tire you need to change. It is pointed to by an arrow molded into the underside of the body.
Main Menu Table of Contents Changing a Flat Tire BRAKE HUB 8. Use the extension and wheel wrench as shown to raise the car until the flat tire is off the ground. 9. Remove the wheel nuts and flat tire. Temporarily place the flat tire on the ground with the outside surface of the wheel facing up. Placing the wheel face down could mar its finish. 10. Before mounting the spare tire, wipe any dirt off the mounting surface of the wheel and hub with a clean cloth.
Main Menu Table of Contents Changing a Flat Tire 11. Put on the spare tire. Put the wheel nuts back on finger-tight, then tighten them in a crisscross pattern with the wheel wrench until the wheel is firmly against the hub. Do not try to tighten them fully. Taking Care of the Unexpected 12. Lower the car to the ground and remove the jack. 13. Tighten the wheel nuts securely in the same crisscross pattern. Have the wheel nut torque checked at the nearest automotive service facility.
Main Menu Table of Contents Changing a Flat Tire 14. Remove the tool box from the trunk well and replace the jack, wheel wrench and extension in the tool box. 16. Replace the spare tire cover. Secure it with the three clips. Push each clip down securely, and pivot the ring down flat. 15. Place the tool box into the spare tire shelf in the trunk. 17. Put the flat tire in the trunk well vertically as shown.
Main Menu Table of Contents If Your Engine Won't Start Diagnosing why your engine won't start falls into two areas, depending on what you hear when you press the ENGINE START button. You hear nothing, or almost nothing. The engine's starter motor does not operate at all, or operates very slowly. You can hear the starter motor operating normally, or the starter motor sounds like it is spinning faster than normal, but the engine does not start up and run.
Main Menu Table of Contents If Your Engine Won't Start If the headlights dim noticeably or go out when you try to start the engine, either the battery is discharged or the connections are corroded. Check the condition of the battery and terminal connections (see page 177). You can then try jump starting the car from a booster battery (see page 222).
Main Menu Table of Contents ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ Jump Starting If your car's battery has run down, you may be able to start the engine by using a booster battery. Although this seems like a simple procedure, you should take several precautions. A battery can explode if you do not follow the correct procedure, seriously injuring anyone nearby. Keep all sparks, open flames, and smoking materials away from the battery. To jump start your car, follow these directions closely: 1.
Main Menu Table of Contents Jump Starting 5. If the booster battery is in another vehicle, have an assistant start that vehicle and run it at a fast idle. 3. Connect one jumper cable to the positive ( + ) terminal on your Honda's batteiy. Connect the other end to the positive ( + ) terminal on the booster battery. 4. Connect the second jumper cable to the negative (—) terminal on the booster battery. Connect the other end to the metal projection near the intake manifold as shown in the illustration.
Main Menu Table of Contents Jump Starting 7. Once your car is running, disconnect the negative cable from your car, then from the booster battery. Disconnect the positive cable from your car, then the booster battery. BOOSTER BATTERY 6. Start your car. If the starter motor still operates slowly, check the jumper cable connections to make sure they have good metal-tometal contact.
Main Menu Table of Contents ０３／０７／１０ The reading on your car's temperature gauge should stay in the midrange under most conditions. It may go higher if you are driving up a long steep hill on a very hot day. If it climbs to the red mark, you should determine the reason. NOTICE Driving with the temperature gauge reading at the red mark can cause serious damage to your engine. Your car can overheat for several reasons, such as lack of coolant or a mechanical problem.
Main Menu Table of Contents If Your Engine Overheats 6. Look for any obvious coolant leaks, 7. If you don't find an obvious leak, such as a split radiator hose. check the coolant level in the Everything is still extremely hot, radiator reserve tank (see page ０３／０７／１０ １６：１１：０９ ３１Ｓ５Ａ９３０ ００２１ so use caution. If you find a leak, it 120). If the level is below the must be repaired before you M IN mark, add coolant to halfway continue driving (see Emergency between the MIN and MAX marks. Towing on page 241). 8.
Main Menu Table of Contents If Your Engine Overheats 10. Start the engine and set the temperature control dial to maximum. Add coolant to the radiator up to the base of the filler neck. If you do not have the proper coolant mixture available, you can add plain water. Remember to have the cooling system drained and refilled with the proper mixture as soon as you can. 11. Put the radiator cap back on tightly. Run the engine and watch the temperature gauge.
Main Menu Table of Contents Low Oil Pressure Indicator LOW OIL PRESSURE INDICATOR NOTICE Running the engine with low oil pressure can cause serious mechanical damage almost irnmediately. Turn off the engine as soon as you can safely get the car slopped. PUSH CANCEL This indicator should light when the ignition switch is ON (II), and go out after the engine starts. It should never come on when the engine is running.
Main Menu Table of Contents Charging System Indicator CHARGING SYSTEM INDICATOR Immediately turn off all electrical accessories: radio, heater, A/C, cruise control, etc. Try not to use other electrically-operated controls such as the power windows. Keep the engine running and take extra care not to stall it. Starting the engine will discharge the battery rapidly.
Main Menu Table of Contents Malfunction Indicator Lamp MALFUNCTION INDICATOR LAMP PUSH CANCEL This indicator comes on for a few seconds when you turn the ignition switch ON (II). If it comes on at any other time, it indicates one of the engine's emissions control systems may have a problem. Even though you may feel no difference in your car's performance, it can reduce your fuel economy and cause your car to put out excessive emissions. Continued operation may cause serious damage.
Main Menu Table of Contents Malfunction Indicator Lamp Readiness Codes Your car has certain "readiness codes" that are part of the on-board diagnostics for the emissions systems. In some states, part of the emissions testing is to make sure these codes are set. If they are not set, the test cannot be completed. If possible, do not take your car for a state emissions test until the readiness codes are set. See State Emissions Testing on pages 255 and 256.
Main Menu Table of Contents Brake System Indicator BRAKE SYSTEM INDICATOR The Brake System Indicator normally comes on when you turn the ignition switch ON (II). It is a reminder to check the parking brake. It comes on and stays lit if you do not fully release the parking brake. Taking Care of the Unexpected If it comes on at any other time, it indicates a problem with the car's brake system. In most cases, the problem is a low fluid level in the brake fluid reservoir.
Main Menu Table of Contents Closing the Convertible Top If the electric motor will not close the convertible top, do the following. CONNECTOR 1. Check the fuse for the convertible top motor (see page 235). If the fuse is blown, replace it with one of the same or lower rating. 2. Try closing the convertible top. If the new fuse blows immediately or the convertible top still does not operate, you can close the convertible top manually. 3. Locate the electrical connector for the convertible top motor.
Main Menu Table of Contents Fuses All the electrical circuits in your car have fuses to protect them from a short circuit or overload. These fuses are located in three fuse boxes. The interior fuse box is underneath the dashboard on the driver's side. There are two under-hood fuse boxes in the engine compartment. The main fuse box is located on the passenger's side near the battery. To open it, push the two tabs as shown.
Main Menu Table of Contents Fuses Checking and Replacing Fuses If something electrical in your car stops working, the first thing you should check for is a blown fuse. Determine from the chart on pages 237 and 238 , or the diagram on the fuse box lid, which fuse or fuses control that component. Check those fuses first, but check all the fuses before deciding that a blown fuse is not the cause. Replace any blown fuses and check the component's operation.
Main Menu Table of Contents Fuses FUSE PULLER BLOWN If you replace the blown fuse with a spare fuse that has a lower rating, it might blow out again. This does not indicate anything wrong. Replace the fuse with one of the correct rating as soon as you can. NOTICE 4. Check the smaller fuses by pulling out the fuse with the fuse puller provided in the interior fuse box. 5. Look for a burned wire inside the fuse. If it is burned, replace it with one of the spare fuses of the same rating or lower.
Main Menu Table of Contents Fuses INTERIOR FUSE BOX * : Canadian Model CONTINUED Taking Care of the Unexpected
Main Menu Table of Contents Fuses UNDER-HOOD FUSE BOXES (MAIN FUSE BOX) (AUXILIARY FUSE BOX) Taking Care of the Unexpected
Main Menu Table of Contents If Your Car Gets Stuck If your car gets stuck in sand, mud, or snow, call a towing service to pull it out (see page 241). For very short distances, such as freeing the car, you can use the detachable towing hook that mounts on the anchors in the front and rear bumpers. To use the towing hook: 2. Remove the towing hook, hook extension and wheel wrench from the tool box. 3. Using the wheel wrench, fasten the extension into the bolt hole in the anchor. 1.
Main Menu Table of Contents If Your Car Gets Stuck 4. Screw the towing hook into the extension and tighten it securely by hand. NOTICE To avoid damage to your car. use the towing hook for straight, flat ground towing only. Do not tow at an angle. The tow hook should not he used to tow t/ie vehicle onto a flat bed. Do not use it as a tie down.
Main Menu Table of Contents Emergency Towing If your car needs to be towed, call a professional towing service or, if you belong to one, an organization that provides roadside assistance. Never tow your car behind another vehicle with just a rope or chain. It is very dangerous. There are three popular types of professional towing equipment. Flat-bed Equipment — The operator loads your vehicle on the back of a truck. This is the only way your S2000 should be transported.
Main Menu Table of Contents Emergency Towing Sling-type Equipment — The tow truck uses metal cables with hooks on the ends. These hooks go around parts of the frame or suspension and the cables lift that end of the car off the ground. Your car's suspension and body can be seriously damaged. This method of towing is unacceptable.
Main Menu Technical Information The diagrams in this section give you the dimensions and capacities of your Honda, and the locations of the identification numbers. It also includes information you should know about your vehicle's tires and emissions control systems. Identification Numbers................. 244 Specifications................................. 246 DOT Tire Quality Grading (U.S. Vehicles)....................... 248 Treadwear.................................. 248 Traction.....................
Main Menu Table of Contents Identification Numbers Your car has several identifying numbers located in various places. VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is the 17-digit number your Honda dealer uses to register your car for warranty purposes. It is also necessary for licensing and insuring your car. The easiest place to find the VIN is on a plate fastened to the top of the dashboard. You can see it by looking through the windshield on the driver's side.
Main Menu Table of Contents Identification Numbers The Engine Number is stamped on the left front corner of the engine block. TRANSMISSION NUMBER The Transmission Number is on a label underneath the transmission.
Main Menu Table of Contents Specifications page 176 Including the coolant in the reserve tank and that remaining in the * 1 : engine. * Technical Information Reserve tank capacity: 0.16 US gal (0.6 , 0.13 Imp gal) 2 : Excluding the oil remaining in the engine.
Main Menu Table of Contents Specifications page 238 page 237 Technical Information
Main Menu Table of Contents DOT Tire Quality Grading (U.S. Vehicles) The tires on your vehicle meet all U.S. Federal Safety Requirements. All tires are also graded for treadwear, traction, and temperature performance according to Department of Transportation (DOT) standards. The following explains these gradings. Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between the tread shoulder and the maximum section width.
Main Menu Table of Contents DOT Tire Quality Grading (U.S. Vehicles) Temperature — A, B, C The temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Main Menu Table of Contents Oxygenated Fuels Some conventional gasolines are being blended with alcohol or an ether compound. These gasolines are collectively referred to as oxygenated fuels. To meet clean air standards, some areas of the United States and Canada use oxygenated fuels to help reduce emissions. If you use an oxygenated fuel, be sure it is unleaded and meets the minimum octane rating requirement. Before using an oxygenated fuel, try to confirm the fuel's contents.
Main Menu Table of Contents Driving in Foreign Countries If you are planning to take your Honda outside the U.S. or Canada, contact the tourist bureaus in the areas you will be traveling in to find out about the availability of unleaded gasoline with the proper octane rating. If unleaded gasoline is not available, be aware that using leaded gasoline in your Honda will affect performance and fuel mileage, and damage its emissions controls. It will no longer comply with U.S.
Main Menu Table of Contents Emissions Controls The burning of gasoline in your car's engine produces several byproducts. Some of these are carbon monoxide (CO), oxides of nitrogen (NOx) and hydrocarbons (HC). Gasoline evaporating from the tank also produces hydrocarbons. Controlling the production of NOx, CO, and HC is important to the environment. Under certain conditions of sunlight and climate, NOx and HC react to form photochemical "smog.
Main Menu Table of Contents Emissions Controls Exhaust Emissions Controls The exhaust emissions controls include four systems: PGM-FI, Ignition Timing Control, Secondary Air Injection System and Three Way Catalytic Converter. These four systems work together to control the engine's combustion and minimize the amount of HC, CO, and NOx that comes out the tailpipe. The exhaust emissions control systems are separate from the crankcase and evaporative emissions control systems.
Main Menu Table of Contents Three Way Catalytic Converter Keep the engine tuned-up. The three way catalytic converter contains precious metals that serve as catalysts, promoting chemical reactions to convert the exhaust gasses without affecting the metals. The catalytic converter is referred to as a three-way catalyst, since it acts on HC, CO, and NOx. A replacement unit must be an original Honda part or its equivalent.
Main Menu Table of Contents State Emissions Testing Testing of Readiness Codes If you take your vehicle for a state emissions test shortly after the battery has been disconnected or gone dead, it may not complete the test. This is because of certain "readiness codes" that must be set in the on-board diagnostics for the emissions systems. These codes are erased when the battery is disconnected, and set again only after several days of driving under a variety of conditions.
Main Menu Table of Contents State Emissions Testing Select a nearby lightly traveled major highway where you can maintain a speed of 50 to 60 mph for at least 20 minutes. Drive on the highway in 5th. Do not use the cruise control. When traffic allows, drive for 90 seconds without moving the accelerator pedal. (Vehicle speed may vary slightly; this is okay.
Main Menu Warranty and Customer Relations Customer Relations Information................................. 258 U.S. Zone Office Map.................... 259 Canada Zone Office Map.............. 260 Warranty Coverages..................... 261 Reporting Safety Defects (U.S. Vehicles)........................... 262 Authorized Manuals......................
Main Menu Table of Contents Customer Relations Information Honda dealership personnel are trained professionals. They should be able to answer all your questions. If you encounter a problem that your dealership does not solve to your satisfaction, please discuss it with the dealership's management. The Service Manager or General Manager can help. Almost all problems are solved in this way.
Main Menu Table of Contents U.S. Zone Office Map Western Zone P.O. Box 2260 700 Van Ness Avenue Torrance, California 90501-1490 (310)781-4565 Mid-Atlantic Zone 902 Wind River Ln., Suite 200 Gaithersburg, Maryland 20878 (301)990-2020 Northwestern Zone P.O. Box 20186 12439 N.E.
Main Menu Table of Contents Canada Zone Office Map CUSTOMER RELATIONS RELATIONS AVEC LA CLIENTELE Honda Canada Inc.
Main Menu Table of Contents Warranty Coverages U.S. Owners Your new Honda is covered by these warranties: New Car Limited Warranty — covers your new vehicle, except for the battery, emissions control systems and accessories, against defects in materials and workmanship. Emissions Control Systems Defects Warranty and Emissions Performance Warranty — these two warranties cover your car's emissions control systems. Time, mileage, and coverage are conditional.
Main Menu Table of Contents Reporting Safety Defects (U.S. Vehicles) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying American Honda Motor Co., Inc.
Main Menu Table of Contents Authorized Manuals Purchasing Factory Authorized Manuals (U.S. only) The following publications covering the operation and servicing of your car can be obtained from Helm Incorporated, either by filling out the attached form or, for credit card holders, calling the toll-free phone number on the form. For manuals prior to the year shown below, contact Helm Incorporated, P.O. Box 07280, Detroit, Michigan 48207, or call 1-800-782-4356. Valid only for sales within the U.S.
Main Menu Table of Contents Authorized Manuals Service Manual: This manual covers maintenance and recommended procedures for repair to engine and chassis components. It is written for the Journeyman mechanic, but is simple enough for most mechanically-inclined owners to understand. Electrical Troubleshooting Manual: This manual complements the Service Manual by providing in-depth troubleshooting information for each electrical circuit in your car.
Main Menu Index Accessories Installation..................................122 Accessory Power Socket................ 82 ACCESSORY (Ignition Key Position).......................................61 Additives, Engine Oil..................... 158 Airbag (SRS)......................................9 Air Cleaner Element...................... 172 Air Conditioning............................... 86 Maintenance............................... 182 Usage...........................................86 Air Outlets (Vents)..
Main Menu Index Changing Oil How to......................................... 159 When to....................................... 146 Changing a Flat Tire ..................... 215 Changing Engine Coolant............. 163 Charging System Indicator ... 44, 229 Check Engine Eight............... 45, 230 Checklist, Before Driving............. 130 Child Safety.................................... 19 Child Seats........................................ 22 Cleaner, Air....................................
Main Menu Index Closing the Convertible Top.... 233 Low Oil Pressure Indicator...... 228 Malfunction Indicator Lamp .... 230 Overheated Engine................... 225 Emergency Brake............................ 81 Emergency Flashers....................... 80 Emergency Trunk Opener............. 67 Emissions Controls........................ 252 Emissions Testing, State .............. 255 Engine Check Engine Light............45, 230 Compartment, Checking in the.......................................
Main Menu Index Gauges............................................. . 47 Engine Coolant Temperature .... 47 Fuel............................................... . 48 Speedometer............................... . 47 Tachometer................................. . 47 Gearshift Lever Positions 6-speed Manual Transmission.......................... 133 Glass Cleaning............................... 209 Halogen Headlight Bulbs.............. 194 Hazard Warning Flashers...............
Main Menu Index Low Oil Pressure Indicator... 44, 228 Lubricant Specifications Chart.... 246 Luggage.......................................... 124 Maintenance................................... 143 Owner Maintenance Checks.... 155 Record......................................... 153 Schedule..................................... 146 Maintenance Required Indicator... 49 Malfunction Indicator Lamp. 45, 230 Manual Transmission.................... 133 Manual Transmission Fluid ......... 168 Meters, Gauges......
Main Menu Index Recovery Vehicle, Emergency Towing........................................241 Reminder Lights............................. 43 Remote Transmitter........................ 63 Replacement Information Air Cleaner................................. 172 Engine Coolant........................... 163 Engine Oil and Filter................. 159 Fuses.......................................... . 235 Eight Bulbs................................. 194 Schedule.....................................
Main Menu Index Storing Your Car............................ 202 Stuck Car........................................ 239 Supplemental Restraint System Servicing...................................... . 38 SRS Indicator..........................37, 45 Tensioners, Seat Belts................ 37 Tachometer..................................... . 47 Taillights, Changing Bulbs in....... 198 Taking Care of the Unexpected .. 213 Technical Descriptions DOT Tire Quality Grading....... 248 Emissions Control Systems.....
Main Menu Index WARNING, Explanation of.............. ii Warning Labels, Location of.......... 40 Warranty Coverages..................... 261 Washer, Windshield Checking the Fluid Level......... 167 Operation.................................... 54 Washing......................................... . 204 Waxing and Polishing................... 205 Wheels........................................... . 189 Alignment and Balance............. 188 Cleaning Aluminum Alloys....... 206 Wrench..........................
Main Menu Service Information Summary Gasoline: Premium unleaded gasoline, pump octane number of 91 or higher. Fuel Tank Capacity: 13.2 US gal (50 l ,11.0 Imp gal) Recommended Engine Oil: API Service SJ "Energy Conserving" oil, SAE 10W-30 viscosity (see page 158). Oil change capacity (including filter): 5.1 US qt(4.8 l ,4.
